The URL can be used to link to this page

Home My WebLink AboutNOAI MIAM1•DADE DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE i MIAMI DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175-2474 T (786) 315-2590 -F (786) 315-2599 ww%mia midad e.eov/economy Sun-Tek Manufacturing, Inc. AUr 10303 General Drive � ,v+-cZ ® 0 O' Orlando, FL 32824 FILE CO ak LU SCOPE: Cie comy This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER- Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Hurricane Self Flashing (HSF) Aluminum Skylight APPROVAL DOCUMENT: Drawing No. HSF-002, titled "HSF", sheets 1 and 2 of 2, dated 01/27/2001, with revision dated 05/04/2015, prepared by Sun-Tek Manufacturing, Inc., signed and sealed by James D. Wells, Jr., P.E., bearing the Miami -Dade County Product Control revision stamp with the Notice of Acceptance number and the expiration date by the Miami -Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, model/series and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided'to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises & renews NOA # 12-0424.05 and consists of this page 1 and evidence submitted pages E4 & E-2 as well as approval document mentioned above. The submitted documentation was reviewed by Hpimy A. Makar, P.E., M.S. llr/ NOA No.15-0513.07 IIAMI•DADE COUNTY Expiration Date: 01/10/2021 Approval Date. 11/05/2015 Page 1 Sun-Tek Manufacturing, lnc.. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. HSF 002, titled "HSF", sheets land 2 of 2, dated 01/27/2001, with revision dated 12/15/2010, prepared by Sun-Tek Manufacturing, Inc., signed and sealed by James D. Wells, Jr., P.E. B. TESTS "Submitted under NOA # I1-0104-09" 1. Test reports on 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per FBC 2411 3.2.1, TAS 202-94 along with marked -up drawings and installation diagram of HSF Polycarbonate Aluminum Fixed Skylights, prepared by National Certified Testing Laboratories, Test Reports No. 210- 3716-1, dated 11/22/2010, with a revision dated 03/07/2010, signed and sealed by Gerard J. Ferrara, P.E. C. CALCULATIONS "Submitted under NOA # 11-0104-09" 1. Anchor calculations prepared by J & L Wells Consulting LLC, dated 01/04/2011, signed and sealed by James D. Wells, Jr., P.E. D. QUALITY ASSURANCE 1. Miami -Dade Department of Permitting, Environment, and Regulatory Affairs (PERA) E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No.12-0110.04 issued to Palram Americas, Inc. for their "Corrugated and Flat Polycarbonate Panels", approved on 02/23/2012 and expiring on 01/22/2016. 2. Notice of Acceptance No. 08-0305.02 issued to SABIC Innovative Plastics for their "Lexan Sheet Products" approved on 04/24/2008 and expiring on 07/17/2013. 3. Notice of Acceptance No.10-0329.03 issued to Sheffield Plastics, Inc., for their"Makrolon Polycarbonate Sheets" approved on 07/07/2010 and expiring on 08/27/2012. F. STATEMENTS 1. Statement letter of code conformance to 2010 FBC issued by J & L Wells Consulting LLC, dated 04/25/2012, signed and sealed by James D. Wells, Jr., P.E. "Submitted underNOA # 11-0104-09" 2. Statement letter of code conformance with FBC 2007 and no fmancial interest issued by J & L Wells Consulting LLC, dated 03/17/2011, signed and sealed by James D. Wells, Jr., P.E. y A. Makar, P.E., M.S. Product Control Section Supervisor NOA No. 15-0513.07 Expiration Date: 01/10/2021 Approval Date:11/05/2015 E -S Sun-Tek Manufacturing, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED j NEW EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. HSF-002, titled "HSF", sheets 1 and 2 of 2, dated 0112712001, with revision dated 0510412015, prepared by Sun-Tek Manufacturing, Inc., signed and sealed by James D. Wells, Jr., P.E. B. TESTS 1. None. C. CALCULATIONS 1. None. D. QUALITY ASSURANCE 1. By Miami -Dade County, Regulatory and Economic Resources Department (RER). E. MATERIAL CERTIFICATIONS 1. None. F. STATEMENTS 1. Statement letter of code conformance to 2014 FBC issued by J & L Wells Consulting LLC, dated 0510512015, signed and sealed by James D. Wells, Jr., P.E. my A. Makar, P.E., M.S. Product Control Section Supervisor NOA No. 15-0513.07 Expiration Date: 01/10/2021 Approval Date:11/05/2015 E -2 J OUTER DOME .093 POLYCARBONATE (Palram Palsun, Sabic Lexan 9034 or SHeiield Makrolon) DECO CLIP .060 6063 T-6 ALUMNIUM ISTI-217 INSULATED AIR SPACE - BUTYL SEALING TAPE (CONTINOUS) DESIGN PRESSURE RATING +- 60 PSF LARGE MISSLE IMPACT RESISTANCE STS 1000 SEALANT CONTINOUS UNDER FRAME AROUND PERIMETER OVER HEADS OF SCREWS 0.25' MINI. 11r PROTRUSION THROUGH ROOF DECK ROOF DECK MIN I" THICKNESS 0 SILCONE DOME SEAL (CONTINOUS) `INNER DOME .080 POLYCARBONATE (Palram Palsun, Sabic Lexan 9034 or Sheffield Makrolon)) INSULATION OR AIR SPACE PVC LINER STI-300 COMPLY WITH SECTION 2612 OF THE F.B.C. DWG.#:HSF-002 #6 X 3!4" HEX HEAD SELF -DRILLING 8 PER SIDE DECO RING .050 �- 6063 T-5 ALUMNIUM STI-208 FRAME ,080 6063 T-6 ALUMNIUM STI-207 U d CORNERS MITERED O AND WELDED W oa M LL EnginaerofRecoid James D. Wells, Jr„ EE. co ProfessionalEngin=No.53616 O v0 J&L WELLS CONSULMNO LLC NOTE: 1453 Arbltm Cird (1) ALL ROOF DETAILS SHALL COMPLY WITH Oviedo, FL 32765 CHAPTER 15 OF THE 2014 FLORIDA BUILDING (407) 4963A89 C�+tlflrale orAudmdraHpn Ne.211� CODE. (2) 4" MINIMUM DISTANCE FROM ANGLE LIP TO ROOF SURFACE FOR SHINGLES OR B.U.R. WITHOUT INSULATION. FOR INSULATION AND TILE ROOF ADD TILE HEIGHT AND oy� INSULATION THICKRIHi�IF�THE 4" MINIMUM HEIGHT. �``,T�S1a10 eM+oGy�P �� PRODVGTRGNSCD #8 X 1" PHILLIPS PAN HEAD m plyhiywl,hlMFlaAd+ ` * 0.63816 �= 8 PER SIDE amle y aae :� s'►� of SUN-TEK MANUFACTURING, 10303 GENERAL DRIVE INC. ORLANDO, FL 32624 \LE: DWG No. F-002 Uv.UU 4.00 —f��P6.75 16,00 0.83 —►{ I FFASTENERSFRAME TO DECK HSF 4646 — — SYMETERICAL 32 FASTENERS DECO RING TO FRANE 1 FASTENER SCHEDULE FRAME TO DECK #8 X 1 PHILLIPS PAN HEAD SCREWS FASTENER SCHEDULE DECO RING TO FRAME #6 X 3/4 .HEX HEAD SELF DRILLING SCREWS MODEL PER LONG SIDE PER SHORT SIDE MODEL PER LONG SIDE PER SHORT SIDE 4646 8 8 4646 8 8 3046 8 6 3046 8 6 3636 7 7 3636 7 7 2246 8 5 2246 8 5 2222 5 5 2222 5 5 DWG.#:HSF-002 NOTE: (1) ALL ROOF DETAILS SHALL COMPLY WITH CHAPTER 15 OF THE 2014 FLORIDA BUILDING CODE. 0 0 (2) 4" MINIMUM DISTANCE FROM ANGLE LIP TO 4.00 MIM. 0 LIP TO ROOF SURFACE FOR SHINGLES OR B.U.R. ROOF WITHOUT INSULATION. FOR INSULATION SURFACE AND TILE ROOF ADD TILE HEIGHT AND INSULATION THICKNESS TO THE 4" MINIMUM cli HEIGHT. _ m N POLYCARBONATE DOME .093 THICK (6 (Palram Palsun, Sheffield Makrolon or Sabic Lexan 9034)) N I1 co POLYCARBONATE DOME .080 THICK -- T (Palram Palsun, Sheffield Makrolon or Sabic Lexan 9034) � 11 J&L WELLS CONSULTING LLC Engineer ofRawrd 1453 Arble�s Circle _ Oviedo, FL 32765 James D. Welle, Jr„ P,B. (407) 496-5489 Professional Eagiaeer No. 53616 Cmdfl.1, ofAuftdBadmNo.2716E DESIGN PRESSURE RATING +- 60 PSF momcraav,sea LARGE MISSLE IMPACT RESISTANCE 8w,, ;�e.ft; A-p oN. oS 3•a7 Jan ow o y! Arc�(yotrd 53616 PRO13UCT NAME: I SUN-TEK 10303 GENERAL DRIVE I NL HSF EN INDUSTRIES, INC. ORLANDo,FL3za2a IDATE:01/28/01 I SCALE_ _ DWG No. HSF-002