HomeMy WebLinkAboutPRODUCT APPROVAL - 1 INCH NAIL STRIP - 10-9-18FILE C
1 c r�v%%-' I
2160 SW Poma Drive
Palm City, FL 34990
jj3to'ot
Compliant with Florida Building Code 2017 (611 ed.) ST. LUCIE COUNTY BUILDING
Compliant with Florida Product Approval Rule # 61G20-3tEVIEWEEpED FOR COMPLIANC
Compliant: Keystone Certifications DATEREVIE1 U o �
PLANS AND PERMIT MUST BE KI
SITE OR NO INSPECTIONS) WI
Product: 1" Nailstrip 26GA Steel Roof Panel FBC Sec.1507.4.2
Yield strength: 50 ksi min.; Attached to min.15/32" plywood or
Wood Deck w/ 0.42 specific gravity with 16" Coverage (Max.)
Rib Height 1"
JJOB
MADE
SCANNED)
By
St Lucie County
Corrosion Resistant Compliant: FBC Sec. 1507.4.3
Fastener 1: #10 x 1" (min.) Pancake Head Wood Screw to penetrate 3/16" (min.) thru
bottom of support.
Adhesive/Sealant : Bostik 9151 Chem -Chalk one component, polyurethane adhesive with
3/16" continuous bead application along base of male rib vertical flange at each panel
seam.
Underlayment: To be compliant with FBC Sec 1507.1.1 CONCEALED FASTENERS OR ATTACHMVTS
ARE THE RESPONSIBILITY OF THE
CONTRACTOR OR RECORD
Slope: Shall be in compliance with FBC Sec.1S07.
1 Install Details: Table A Allowable Loads METHOD 1 METHOD 2 ('
DESIGN PRESSURE* _f86 PSF Main tell 97.25 PSF Perimeter
FASTENER SPACING 6 O.C. _. __. - Ir O.C. ry YW
SEAM ADHESIVE Not required 3/16» continuous bead
Reference Data: ARCHITECTURAL TESTING, INC. TST ID#: 1527
UL 580-06 & UL 1897-04 TEST REPORT D8133.01-450-18 06/30/15 Specimen #1 & #2
ULI897-04 is equivalent to Test Standard ULI897-12.
Certificate of Independence: '
Locke Bowden, P.E. does not have, not will acquire a financial W@mItbttagy�company manufacturing or distributing products
under this evaluation. ����� D • BO
Locke Bowden, P.E. is not owned, operated, or controlle mR r, ►any'aurer, or distributing products under this
report. .' �• '�
12
• '� seal
THESE PLANS AND ALL PROPOSED WORK -a
ARE SUBJECT TO ANY CORRECTIONS ��� STATE OF •• i�r t
REQUIRED BY FIELD INSPECTORS THAT y ,r . Fi OR10�' • +�
MAY BE NECESSARY IN ORDER TO s,',° • • • • " �,�?
COMP WITH ALL APPLICABLE CODES. Pi, ' ,ONAL � :••'
.t..:::►►►�'
Limitations:
1. Onderiayment to be compliance with current Florida Building Code (FBC)2017 6"' ed..
2. Minimum slope to be compliant with Florida Building Code 2017 6�' ed., and per with Manufacturer's installation reference.
3. Products are compliant for State of Florida product approval per Rule 61 G20-3. Compliance Method: 1-D
4. Engineering analysis for "project specific approval by local authorities wfJurisdiction is allowed by other registered engineers.
5. Fire classification is not part of this acceptance. Shear diaphragm values are outside this report.
6. Support framing in compliance w/FBC 2017 6°i ed., Chapter 22 for Steel, Chapter 23 for Wood and Chapter 16 for Structural
Loading.
7. This report does not imply warranty, installation, recommended product use outside of this report.
FL 17022.5 1.0 Nail Strip (26GA Steel),16" Wide Roof Panel - Details
16"
Panel Profile
1 6".o.c.
3/4"
1
Deck:
15/32" or greater Plywood, or
- Wood plank
Snap Lock
For METHOD 2:
Apply 3/16" Bead Bostik 915TM Sealant
Continuous Along Male Rib Vertical Flange
\\\ i.\ `�\ �` - Fastener
#10 x 1" Min. per Table "A"
Pancake Head Wood Screw
(Typical Fastening Pattern Across Width)
1"
FL 17022.5 1.0 Nail Strip (26GA Steel),16" Wide Roof Panel - Details
YGN\.
15/32" or greater Plywood, or
- Wood plank
Pnatanar
Isometric View
FUI MUL' 1Uu c
Apply 3116" Bead Bostik 915TM Sealant
Continuous Along Male Rib Vertical Flange
(Refer to Table "A")