HomeMy WebLinkAboutNOA - ALUMINUM SINGLE HUNG WINDOWFILE COPY
M IM I®DADS MIAMI-DADS COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (7W 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.¢ov/economy
Lawson Industries, Inc. SCANNED N 8501 W 90 Street BY
Medley, FL 33166
St Lucie bounty
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction
.materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami -Dade County) and/ or the AHJ (in areas other than Miami -Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER
reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control
Section that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone. -
DESCRIPTION: Series "SH-7700 (Flange Frame)" Aluminum Single Hung Window - L.M.I.
APPROVAL DOCUMENT: Drawing No. L7700-0901, titled "Series-7700 Single Hung Flange Frame
Impact Window", sheets 1 through 5 of 5, dated 05/27/09, with revision C dated 09/21/16, prepared by
manufacturer, signed and sealed by Thomas J. Sotos, P.E., bearing the Miami -Dade County Product Control
Revision stamp with the Notice of Acceptance number and expiration date by the Miami -Dade County
Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LIMITATIONS: insulated Glazing Options Types 6 and 7 are not approved to be installed above 30 feet in
height without external protection device (shutters)
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, series,
and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been
no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change
in the materials, use, and/ or manufacture of the product or. process. Misuse of this NOA as an endorsement
of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure
to comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and
followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is
displayed, then it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises and renews NOA No. 14-0908.10 and consists of this page 1 and evidence pages E-1
and E-2, as well as approval document mentioned above. ' - .
The submitted documentation was reviewed by Manuel Perez, P.E.
MIAM►-DADe COUNTY NOA No. 16-1003.01
.. , . Expiration Date: December 27, 2021
2jS jl(p Approval Date: December 45, 2016
! J i Page 1
Rk !, _u C72 u
�AN' 3379 RCH_ OIL, E111mr; PA
r,APPROVED A.Re*,9 I I Jo5
R—RISE & RESUB.41,IT
0 APPROVc- D A&OOPr,7:c_rED El REJECTED
This rovile--ev �s only fl;
ron.
M.-muce vVIII., VIV- us
WSTI in the w,"tiact
ngs G,,,,4
p!'M2ns kjf�j.it wilh U,,e rem-wra-
ur af, J Y si fall riot f I ','Ah7 thc Rem If atph, is is 0,171,
iob sib,. f;n�
k;laf prb;03 ,f)ISIY !L, Ilia fab"14-pul'on iho n:!_-Lds le&mf PODSMojoosp C7 io
gLreS of r�,,nq of , �hpo_
in 0 Safe and saidsiactcry man ail Wfor lreda3: and for patforming 2,11 v,�Oj.k
DATE: 9"S BY,
M IM I®DADE MIAMI DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.¢ovIeconomv
Lawson Industries, Inc.
8501 NW 90 Street
Medley, FL 33166
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami -Dade County) and/ or the AHJ (in areas other than Miami -Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER
reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control
Section that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone. -
DESCRIPTION: Series "SH-7700 (Flange Frame)" Aluminum Single Hung Window - LALL
APPROVAL DOCUMENT: Drawing No. L7700-0901, titled "Series-7700 Single Hung Flange Frame
Impact Window", sheets 1 through 5 of 5, dated 05/27/09, with revision C dated 09/21/16, prepared by
manufacturer, signed and sealed by Thomas J. Sotos, P.E., bearing the Miami -Dade County Product Control
Revision stamp with the Notice of Acceptance number and expiration date by the Miami -Dade County
Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LINXFATIONS: Insulated Glazing Options Types 6 and 7 are not approved to be installed above 30 feet in
height without external protection device (shutters)
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, series,
and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been
no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change
in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement
of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure
to comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and
followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is
displayed, then it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises and renews NOA No. 14-0908.10 and consists of this page l and evidence pages E-1
and E-2, as well as approval document mentioned above.
The submitted documentation was reviewed by Manuel Perez, P.E.
MlAMMADE COUNTY NOA No. 16-1003.01
Expiration Date: December 27, 2021
ki,
Approval Date: December 15,2016
i Page 1
Lawson Industries, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
A. DRAWINGS
1. Manufacturer's die drawings and sections.
(Submitted under NOA No. 09-0706.09)
2. Drawing No. L7700-0901, titled "Series-7700 Single Hung Flange Frame Impact
Window", sheets 1 through 5 of 5, dated 05/27/09 with revision C dated 09/21/16,
prepared by manufacturer, and signed and sealed by Thomas J. Sotos, P.E.
B. TESTS
1. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of an aluminum single hung
window, prepared by Hurricane Engineering & Testing, Inc., Test Reports No. FiETI-
09-2530A and HETI-09-2530B, dated 03/02/09, signed and sealed by Candido F.
Font, P.E. (Submitted under NOA No. 09-0706.09)
2. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of an aluminum single hung
window, prepared by Hurricane Engineering & Testing, Inc., all Test Reports No.
HETI-08-2003C, HETI-08-2004A, HETI-08-2060A & B, HETI-08-2061A & B,
HETI-08-2062A & B, HETI-08-2063A & B, BETI-08-2064A & B, dated 03/15/08,
signed and sealed by Candido F. Font, P.E. (Submitted under NOA No. 08-0825.17)
3. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test, per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6) Forced Entry Test, per FBC 2411 3.2.1, TAS 202-94
along with marked -up drawings and installation diagram of an aluminum single hung
window, prepared by • Fenestration Testing Laboratory, Inc., Test Reports No. FTL-
2987 and FTL-2986, dated 04/03/01 and 03/27/01, all signed and sealed by Luis
Antonio Figueredo, P.E. (Submitted under NOA No. 01-1009.01)
C. CALCULATIONS
1. Anchor verification calculations and structural analysis, complying with FBC,
prepared by Lawson Industries, Inc., dated 05/28/09, revised on 01/18/10, signed and
sealed by Thomas J. Sotos, P.E. (Submitted under NOA No.11-0705.09)
2. Glazing complies with ASTM E1300-09
ManGel
erez, P.E.
ProductCoExaminer
NOA No.16-1003.01
Expiration Date: December 27, 2021
Approval Date: December 15, 2016
E-1
Lawson Industries, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
D. QUALITY ASSURANCE ,
1. Miami -Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 14-0916.11 issued to Kuraray America, Inc. for their
"SentryGlas® (Clear and White) Glass Interlayers" dated 06/25/15, expiring on
07/04/18.
2. Notice of Acceptance No.14-0916.10 issued to Kuraray America, Inc. for their
"Butacite® PVB Glass Interlayer" dated 04/25/15; expiring on,12/11/16.
3. Notice of Acceptance No. 14-0423.17 issued to Eastman Chemical Company (MA)
for their "Saflex Clear and Color Glass Interlayers" dated 06/19/14, expiring on
05/21/16.
F. STATEMENTS
1. Statement letter of conformance, complying with FBC-5'h Edition (2014), and of no
financial interest, dated September 30, 2016, issued by manufacturer, signed and
sealed by Thomas J. Sotos, P.E.
2. Statement letter of no financial interest, dated 05/28/09, issued by manufacturer,
signed and sealed by Thomas J. Sotos, P.E. (Submitted under NOA No.11-0705.09)
3. Laboratory compliance letter for all Test Reports No. HETI-09-2530A & B, issued by
Hurricane Engineering & Testing, Inc., dated 03/02/09, signed and sealed by Candido
F. Font, P.E. (Submitted under NOA No. 09-0706.09)
4. Laboratory compliance letter for Test Reports No. HETI-08-2003C, HETI-08-
2004A, HETI-08-2060A & B, BETI-08-2061A & B, HETI-08-2062A & B,
HETI-08-2063A & B, HETI-08-2064A &B, issued by Hurricane Engineering &
Testing, Inc., dated 03/15/08, signed and sealed by Candido F. Font, P.E.
(Submitted under NOA No. 08-0825.17)
5. Laboratory compliance letter for Test Reports No. FTL-2987 and FTL-2986, issued
by Fenestration Testing Laboratory, Inc., dated 04/03/01 and 03/27/01, signed and
sealed by Luis Antonio Figueredo, P.E. (Submitted under NOA No. 01-0406.08)
I G. OTHERS
1. Notice of Acceptance No.14-0908.10, issued to Lawson Industries, Inc. for their
Series "SH-7700 (Flange Frame)" Aluminum Single Hung Window — L.M.I.",
approved on 11/06/14 and expiring on 12/27/16.
Manuel P ez, .E.
Product Control xa finer
NOA No. 16- 0101
Expiration Date: December 27, 2021
Approval Date: December 15, 2016
E-2
Y4Wv FLN4CBFNN( vi01N
w umoas
FAnE aii
uNis cscE sr¢r FKI
nA'x U. Al
E /
A•
ALL [ ERB
16. YAK. U.Lo.
16
11/16
= ag
l
xBEL�OV
I' ��'I rn E
E.I. a WI. FALSE COLONIAL
C
.. MS ARE -LIE. V/ VINOLIvr B�iAt V10r11 YIN00Y 0.rY VIOrN
V/ S UTWE W0 PRE nVPILABLC AB OPTIOxAL. vINMV RCK VIOIN
AVAILABLE AS OPTIMAL. 40' x 70' EQUAL LITE ELEVATION UN -EQUAL LITE RADIUS ELEVATION UN -EQUAL LITE ELEVATION
• INCLINES UN -EQUAL UTZ AND RADNIS HEAD (UMRED TO LOA05 ON SMELT 4 OF b) (LIMITED TO LOADS ON SMELT 4 OF S)
(LOUSED
TO WADS ON SHEEP 4 OF S) General Notes: SERIES-7700 SINGLE HUNG IMPACT WINDOW — FLANGE FRAME
1.) THIS WINDOW SYSTEM IS DESIGNED AND TESTED TO COMPLY WITH THE REQUIREMENTS b�Rs•_,
OF THE 2014 FLORIDA BUILDING CODE SLN EDITION INCLUDING HIGH VELOCITY HURRICANE INS aAL11Da AAx Rs.--- YINBw nAce rnPN[ YlBrx
ZONE VELOCI7Y (HYHZ) AND Aefi1 1300-U9. THIS PRODUCT IS IMPACT RESISTANT. E rvEAS \ HaO ,
(SHUTTERS NOT REQUIRED) iw rim�i vca �xuc saE
�, P BT ISEE -I ..I -i X � r
2.) WOOD BUCKS SHALL BE INSTALLED AND ANCHORED SO THAT THE BUILDING A C 4
NERISIE THE SUPERIMPOSED WADS IN ACCORDANCE WITH THE REQUIREMENTS S, Dp[jL AT
OF 2014 P.B.C. & TO BE REVIEWED BY BUILDING OFFICIAL CORNERS
3.) ANCHORSISHOWN ABOVE ARE AS PER TEST UNTIE. ANCHORS ON ALL WINDOW SIZES Ma D.L.O. W Lh
ARE NOT ;TO EXCEED THESE MAXIMUM SPACINGS ON CENTER (O.C.) AND AS TABULATED Si IB II IQ,
ON SHEET 4.
4.) ANCHOR CONDITIONS NOT DESCRIBED IN THESE DRAWINGS ARE TO BE 0 'MgR
ENGINEERED ON A SITE SPECIFIC BASIS, UNDER SEPARATE APPROVAL AND Sh >B ryCEIIRIaW C I✓/ TO BE REVIEWED BY BUILDING OFFICIAL Y� D
3J WINDOWS ARE QUALIFIED FOR USE WITH SINGLE GLAZE LAMINATED GLASS 8 S
TYPES TABULATED HEREIN (SEE SHEET ®3), AND FOR USE WITH DOUBLE GLAZE •' 4
LAMINATED INSULATED CLASS TYPES TABULATED HEREIN (SEE SHEET 93).
B.) SEE 9HECT 3 FOR LOCK DETAILS & OPTIONS. ET "eV
7.) SEE SHE4 FOR DESIGN PRESSURES AND CLASS TYPES. =
22 J— li / tt i C
B.) FOR OPTIONAL FRAME INSTALLATION DETAILS SEE SHEET 3. tl� II i
9.) EXT, & INT. FALSE COLONIAL MUNTLNS ARE OPTIONAL & AND ARE APPLIED W/ SILICONE
10.) ROOD BUCKS IN CONTACT WITH CONCRETE MUST BE PRESSURE TREATED AND ANCHORED /7;/^,; 6
(BY OTHERS), PRIOR TO WINDOW LNSTAUATION. (SEE SHEET A2 FOR DETAIL & NOTES) �Lw PRODUCTREVI56BVISED
WOOD BUCKS TO BE ANCHORED IN COMPLIANCE WITH THE 2014 FBC CHAPTER 24, ( " PWINNB ybrAlB
SECTION 11.3.3.3. bux OWAE4�(b•b A
I1J APPROVAL,APPLIES TO SINGLE UNITS OR S(DE BY SIDE MULLED UNITS. Del
I2J MULLING SINGLE HUNG WINDOWS WITH OTHER TYPES OF MIAMI-DADE COUNTY APPROVED EXT. a WT. FALSE cOLOlIAL C DY WINDOWS USING A MIAMI-DADE COUNTY APPROVED MULLION IN BETWEEN ARE ACCEPTABLE EXT. LS ARE APPLIED v
BUT THE LOWER DESIGN PRESSURE FROM THE WINDOWS OR MULLION APPROVAL WILL APPLY y TWSARE — ARE b2IxT Nome
TO THE ENTIRE MULLED SYSTEM. W/ SILI AS �r[axa.. vIxLGV RCx vIDtR
13.) SEE SHEET A 3 FOR MULLON/METAL ATTACHMENT DETAILS & OPTIONS. EQUAL LATE ELEVATION
I4J ALL YETAL/STEEL IN CONTACT
WITH ALUMINUM OR OTHER DISSIMILAR MATERIALS TO BE (WILTED TO LOADS ON SHEET 4 OF b)
PAINTED OR PLATED AND SHALL MEE[ SECTION 2003.6.4 OF THE 2014 FLORIDA SLOG. CODE.
y
m
OL
O
1/4' TAPCON W/ 1 1/4--
MIN. EMBEDMENT INTO GONG.
(SEE ELEVATION AT SHEET
FOR MAX. FASTENER SPACIN
1 1/B•
EXTERIOR
a
C.
O
ALL WOO O BUCKS ENGINEERED SEPARATELY —
A TO BE REVIEWED BY BLDG. OFFICIAL (TYPJ
P.T WOOD BUCK NOT BY LAWSON IND.
MUST SUSTAIN IMPOSED LOADS
, �MBCOMENT
d
SILICONE RINDS1VE
DEDDING COMPCUND
LAMINATED CUSS
T4
INTERIOR
RAILS (IB1
.414 SMS. V/ 1 1/4'
ED MIN EMBMENT LNTD WOOD.
wTED FAASS PT. V®D BUCKS
(SEC ELEVATICN AT SNEET 41
FOR NAX. FASTENER SPACING)
4
y
"
SILICCKE ANESIVE
DJ
C
BEDDING COMPOUND
qo
m
z Z
18 1 INTERIOR
T la rnvLm� V/ I ...•
y
x
Sy MIN. EMBEDMENT WIG CONC.
(SEE ELEVATION AT SWEET Ill
y
FDR MAL FASTENER SPACING)
• _
m � o e
O
IT
2
``
C
N
12 1A1NIM
2 p
2
B
2
-
1 MIN
' EDGEEDISTANCE
miy
!
51
W y
o
a
0
D A D EXTERIOR
EXTERIOR GRADE
PERIMETER CALLKING
WLYDDV FWWC
' V/ 1 1/4'
WIDDI
V
S
CDMENT INTD WODn D�Br
EVATI. AT AI� D --jl
FASTENER SPACING)
iY1NDOW INSTA .ATION NOT
1. THE WINDOW FRAME FLANGE TO BE BACK -BEDDED W/ AN EXT.
(� O
EXT. CRADE
CAUII(
GRADE CAULK THROUGHOUT THE ENTIRE PERIMETER OF FLANGE
BY WINDOW INSTALLER (TYPJ
B. THE EXPOSED EXT. PERIMETER OF THE WINDOW FRAME TO
BE SCALED V/ AN APPROVED EXTERIOR WADE CAULK
BY OTHERS (TYPJ
�I
1 o
f
I
• WHEN THE CAP BETWEEN THE WINDOW FRAME AND THE BUCK OR
2
DO
MASONRY IS IEM THAN 1/8', SHINS ARE NGT REQUIRED.
ANCHORS NOTE:
W
(�
1
ANCHORS TO BE N12 SMS DR WD. SCREWS INTO WOOD, DR
I/A' TAPCONS APPROVED
or CONE. FASTENERS INTO GONG,
WITH A MINIMUM OF 1 1/4' PENETRATION INTO WOOD DR
CONC. (REFER TO LOAD TABLES
o
@@ _
T
i
AT SHEET 4 OF g FOR
QUANTITIES REQUIRED)
e e
AX.
()DUCT REVISBD
INFIA9 wiN tl»A4A&A
1
Pmasa `�
I Idv [dMrG B99
T SOLtE-IOR[14n ln1
xIKO srccrvuN e
Rao�o•
t.Y1NATEO GLA59 CONPOSRfON
- TYPS E
11
0 .FMGG_n
m° f, .ems
me •.wMnLm enii n
IAKpATe OssnOTIW
Fsuu M0.�I
�
--IC•
_ _caw
IAMINATBD GLASS COMPOSITION
-TYPE 3
rtnl
I
a• AwEµEO fuss
1 TI
esewmon
ASTiG MsuAAT(R
M�k� aNnt
�
X n�� C a
WIINATEO cLASS COMPOSETON - TYPE A .
nLI55 RaC®PNOx ORCO. -T1F1 LWnLLR OO¢IPORX
11[ RITORArte _ ein J iMiar A�vrt° q
LAMIOGNNATED GLASS COMPOSITION
-TYPE 6
ITI
TR[NGITFI[D Russ
TASIfC w10.uY[R
iFF6n GLxSi
"j7�'
� .> J
IAYwATR DESCRIPTRn
s'""'Acl,[ M q
. ,z
no
7 ]
•SRILbC� �
2a — Z)T
=. GUNN
NSU4TE0 IA1II AIEO
G COMPOSITION
TYPE 6
TrIM
GLAv sesiPanc�
AR
TT OelLmPllOx
T RN,°t°y
x• IxRI+IFn AW sPAcc
wFALFn (LASS
INSULATED U]IINA7ED
GLASS COMPOSRIO
TYPE-?
ITM
YLse rni�mi[
rtALL
-- 4 m= - �
WNIW1l Gsdavnax
S �wR q
Ec MHc•I ca
!
PusTl[ Ix1OUTO
wKALEn [LASS
'- - - _ ��
Klx SHS. V/ 1 1/4•
KIN. CHILE INTO V000.
ISEE ELEVATION aT S12CT nl 6 6 26 rc
FOR MAX FASTENER SPRCIxGT — INTERIOR IE'Z=-
DO
TERR lwvsxlm�i RmuimlFs, u OII��l-f_Y�II� roNG L1(]U 26iIoeiF,j m R <;LOCK (LATCH AND SWEEP) OPTIONBTOTHERS 111P1. BOTH EXTRUDED ALUMINUM AND PLASTIC LIFT HANDLE
LOCKS ARE QUALIFIED FOR USE ON ALL WINDOWS.2. BOTH DIE CAST AND NYLON CAM LOCKS ARE QUALIFIEDFOR USEONALLWIDOWS.MEXTERIOR 3. TWO (2) LACKS ARE REQUIRED PER EACH VENT. z
KT. GRAK NF IEamw.GUCCOwER HETAL um wuLEn TOd BEGYRYvmn TO .. 11.0.°YITFci wNOTn INmWOOD FRAME INSTALIATION DETADALUMINUM MULLIONO i
SEE M GN AP XS FOR 12 [ G/a• SOS SC YULU M APFRwALS FOR � <
ULI N TYPE. RE ANO IN%I
RAi NERD, I'MILLIPS. WON DBE. 9 E AEm mm.
DESIGN PRESSURE INRATIICK) IS._ ELEVATION AND OESWTI PRESSURE NATAGGNS.
(ALUN. 0.016• YIN. MICN) OTFASTENERRSPACING)Y INTERIOR NO ' THE UX PRESSURES OF JINGLE
NOTE• THE LOWER PRESSURES OF 4 N 1/N• MA)L M nW00N OR MUE S G FwHUNGOR YIAY SM- GOVESWIM •• ,•mINTERI/ SEE2ELE . FOR SP.s/LIXCL dg k_
I
Iluh
NOTE:
1. µ1 Tm' IR GMT_ ,N
0 BE PYNTEO OR PUTEO.
]. A) EF STRIICDIRES:
A) STEEL : FIT - 36 MSI MIN.
g g
i a
G
(sIEE le u MIN. MILK -
8) ALWWUu : 60G]-TS uw.
o.o.s7
S d =
< m
3 aa
N L
r
EXTERIOR
UOR GRADE
ETER CAULKING
PERIMLIEa ww00W FRAME
s'IT EXTERIOR El (uuN. G.GT6' uIN. TwcX)
ii
t
FRAME MULLING DETAILMETAL
STRUCTURE ATTACHMENT DETAI
m ODUCT REVISED
�Ibls
n:r
0� O
OZ�'
N
nBmll Prmmu
9y
,,'AIFA1EE°EIII1lAYLSAY
G,
N OJ N O fW.l tp (NJ �a N ro S m
N V fT N N N [R N N OAo N V N N N W N V O! b N p p
W W Vl N W (Ni,=S (mq NZE b
—___—_—_.—SO!—r _ mono oa mp 2
m V V V A A A A A W W W CoW W W W W DI W W y
e c O y a L A A
W W W N IV N W W W W W W �D O 0 O 1 1 61 N
N U W W S d m N u u y D
F) m O
F
O P � A
<
m
... o W W ..........
W W W o W W W W
(O 0 0 0 0 0 0 0 0 0 0 0 0 0 O O O O p W o 0 0 0
0 0 0 0 0 O O O O O O O o O O O O O
C � m
m t i 1
953 0 0 0 0 o W o 0 0 0 0 0 0 0 0 0 0 0 o q g b" p
0 0 0 0 0 0 0 0 o c o 0 0 0 0 0 0 0 0 o E o y e f
HrCn M
07� 2 moS
L-n!
b0 cocm 00 -- o00000 W 0000 y o my y
9
2L
m
z 1 z
3fl-
V��� SS$o�$m �Ts�mt��N2SN��ic1 < HLn�N{r�i;EYS�EiYJ�mffimeeP,°H'Pu,°ti'�u�•",���� �'e
o �y
ED
I/1
Gi
z
a°
C
ED
m
r
R 1a
�� aw,
o�
{WI EER
y
d r �CENSF Y A ay TS ® n T
0 552?5 a.a.m lOJ 8/8/ 1/\tl/ R501 N.W. 90 A
* ••I* � x01° � MEDLEY, FLORIDA 37166
e c�a co-. em ra,ie„ xm� sT PH No. (305) 696-8660
MANUFACTURER OF QUALITY ALUMINUM IIINDOWS AND CLASS DOORS
�.o .• p ����'�` x. ERxzo-er-ue SERIES-7700 SINGLE H NC FI ANGE FRAME 1
• 00Lp.•'rr?�.�� MPAG"f WINDOW
DATE ° C Eruxo �ppRl a 'a. —M PRESSURE CHARTS. h CONFIGURATION OPTIONS
n L7700-0901 d°nL 4 DY 5
�I
BILL OF MATERIALS
ITEM /
PART /
It D.
DESCRIPTION
RENAItKS
I
L-7801
1
FIN FRAME HEAD
6063-T6 ALUMINUM
2
L-7802
I
IN FRAME SILL
6063-16 ALUMINUM
3
L-7803
2
FIN FRAME JAMB.
6063-T6 ALUMINUM
4
L-7704
1
FRAME FIXED MEETING RAI
6063-T6 ALUMINUM
5
L-7705
1
VENT MEETING (TDP) RAIL
6063-T6 ALUMNUM
6
L-7706
I
VENT BOTTOM (LATCH) RA
6063-T6 ALUMINUM
7
L-7707
2
VENT JAMB (SIDE) RA[L
6063-T6 ALUMINUM
B
L-7708
AS REO'D.
GLAZING BEAD ( 3/8' )
6063-TS ALUMINUM
9
FS-006
AS RED'➢.
FRAME ASSEMBLY SCREVS
98 % 3/4' P.M. PHILLIP
10
FS-040
AS RE00.
INSTALLATION SCREVS
A14 X 1 1/4' FH./PHIL.
11
L-753I
JAS REO'D.
BULB VINYL VTS'P
1/4' ➢IA. BULB 03033
12
PVS-003
AS REO'D.
FIN SEAL WEATHERSTRIP
.187'x.230'
13
PVS-003
AS REG-D.
FIN SEAL WCATHERSTRIP
.187'x.350'
19
PVS-009
AS REG'0.
FIN SEAL WEATHERSTRIP
.187'x.310'
IS
HC-024-1
2
ISELF ADHESIVE PILE PAD
1/4' X 1 1/2'
I6
L-7711
AS REO'D.
GLAZING BEAD/ INSULATED
6063-T5 ALUMINUM
17
L-4204
AS REO'D.
GLAZING BEAD - RADIUS
6063-T5 ALUMINUM
18
L-7723
1 I
SASH BALANCE CAN/GUI➢E
G_ K VENT)
19
L-7725
2
RIGID VINYL SASH STOP
(2 X FRAME)
20
L-7727
2 IBLOCK
A TACKLE BALANCE
BSI BAl=ce Systems
21
L-7539
2
VENT LIFT LATCH
6063-T5 ALUMINUM
22
L-7523
1% LATCM
VENT LATCH SPRING
STAINLESS STEEL
23
AS RED-D.
GLAZING SILICONE
SEE GLAZING 8 SHT. 3
24
2
Lc. -tea Glass
SEE GLAZING DETAILS
25
HC-057-1
2
VENT LIFT LATCH
MOLDED NYLON
26
HC-058-1
2
VENT SVEEP LATCH
MOLDED NYLON
27
2
FRAME SILL TOMGASKET
SELF ADHESIVE
28
HC-026-1
1
SCREEN FRAME 6 MESH
29
L-7730
I
PRODUCT LABEL
30
31
SM-5504
AS RED'➢.
JOINT SEALANT
SM-5504
32
i .
AS REO'D.
PERIMETER ACRYLIC CAULK
OSI POLYSEAMSEAL