HomeMy WebLinkAboutNOA - CURB MOUNT - SELF FLASHING SKYLIGHTSVic
MIAMI• E MIANII-DADS COUNTY
PRODUCT CONTROL SECTION
118 eet, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES + NrMiami Flori a 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION ST. LUCtf 42590 F ( 86) 315-2599
NOTICE OF ACCEPTANCE (NOA) B"' aE I,ew w. iamidade. ov/econom
FOR C -
Maxim Industries, Inc. REVIEWED BY
1630 Terre Colony Court .::r, -: ;'. DATE PLA AND P J ao
Dallas, TX 75212 ,a }, �+j MUST BE KEPT ON JOB OR
r t BE MADE a
NO INSPECTION WILL
SCOPE:
,This NOA is being issued under,,] e,-4oicable rules aria regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER- ®his
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
lHaving Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER
reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control
Section that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone.
DESCRIPTION: Model DCM Curb Mount & DSF Self -Flashing Aluminum Skylights
APPROVAL DOCUMENT: Drawing No. MAX0003, titled "Curb Mounted and Self Flashing Skylights",
prepared by Maxim Industries, Inc, sheets 1 through 5 of 5, dated 12/03/2013, with revision C dated
02/26/2018, signed and sealed by Robert J. Amoruso, P.E., bearing the Miami -Dade County Product Control
revision stamp with the Notice of Acceptance number and expiration date by the Miami -Dade County
Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
ABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state,
l�nodel/series and following statement: "Miami -Dade County Product Control Approved", unless otherwise
noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
'NSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA # 15-0715.08 and consists of this page 1 and evidence submitted pages E-1 & E-2,
as well as approval document mentioned above.
The submitted documentation was reviewed by Helmy A. Makar, P.E., M.S.
ion No. 18-20/2019
Expiration Date: 02/20/2019
Approval Date: 04/19/2018
04�%9lZo fg Page
Maxim Industries, Inc. �r'?
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE,SUBMITTED_UNDER PREVIOUS APPROVAL #15-0715.08
A. DRAWINGS
1. :;;Drawing No. MAX0003, titled "Curb Mounted and Self Flashing Skylights", prepared by
Maxim Industries, Inc, sheets 1 through 5 of 5, dated 12/03/2013, with revision B dated
07./09 015, signed and sealed by Robert J. Amoruso, P.E.
B. ' TESTS -"Submitted underNOA # 14-0318.01"
1. Test reports on 1) Air Infiltration Test, per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test, per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with,marked-up drawings and installation of Self Flashing and Curb Mount Plasti
Glazed Unit Skylights, prepared by Architectural Testing, Inc., Test Report No. D1032.01-
801-18, dated 10/02/2013, and revision 1 dated 02/24/2014, signed and sealed by Vinu J�
Abraham, P.E.
"Submitted under NOA # 13-1217.24" i
2. Test re]�o_rts on 1) Air Infiltration Test, per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test, per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with'marked-up drawings and installation of Self Flashing and Curb Mount Plastic.
Glazed Unit Skylights, prepared by Architectural Testing, Inc, Test Report No. D1032.6-
801-18, dated 10/02/2013, signed and sealed by Vinu J. Abraham, P.E.
C. CALCULATIONS "Submitted under NOA # 13-1217.24"
1. Anchor calculations for substrate installation prepared by PTC Product Design Group, LLC,
dated 12/03/2013, signed and sealed by Robert J. Amoruso, P.E.
D. QUALITY ASSURANCE
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. Notice of acceptance No. 12-0605.05 issued to Bayer MaterialScience LLC (MA), for t eir
Makrolon Polycarbonate Sheets, approved on 12/06/2012 and expiring on 08/27/2017. :
2. Notice of acceptance No. 12-0110.04 issued to Palram Americas, Inc, for their Corrugated and
Flat Polycarbonate Panels, approved on 02/23/2012 and expiring on 01/22/2016.
i
F. STATEMENTS
1. Statement letter of code conformance to the 51 edition (2014) FBC and of no financial i�terest
issued by PTC Product Design Group, LLC, dated 07/09/2015, signed and sealed by Robert J.
Amoruso, P.E.
elmy A. Makar, P.b I, M.S.
Product Control Section Supervisor
NOA No. 18-0307.10
Expiration Date: 02/ 6/2019
Approval Date: 04/ 4/2018
E -1 Iii
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL #15-0715.08
DRAWINGS
1. Drawing No. M4X0003, titled "Curb Mounted and Self Flashing Skylights'; prepared by
Maxim Industries, Inc, sheets 1 through 5 of 5, dated 1210312013, with revision C dated
0212612018, signed and sealed by Robert J. Amoruso, P.E.
TESTS
1. None.
CALCULATIONS
1. None.
QUALITY ASSURANCE
1. By Miami -Dade County Department of Regulatory and Economic Resources (RER)
MATERIAL CERTIFICATIONS
1. None.
STATEMENTS
1. Statement letter of code conformance to the 0 edition (2017) FBC and of no financial interest
issued by PTC Product Design Group, LLC, dated 0212612018, signed and sealed by Robert J
Amoruso, P.E.
")�- wz_�
elmy A. Makar, P.E., M.S.
Product Control Section Supervisor
NOA No. 18-0307.10
Expiration Date: 02/20/2019
Approval Date: 04/19/2018
E. 2
A A L'\'7.DU3
D CM CURB MO UNT & DSF SELF-FLA SHIN
LV TALLATIONANCHORAGE DETAILS
GENERAL NOTES:
1. THIS PRODUCT IS DESIGNED TO COMPLY WITH THE HIGH VELOCITY HURRICANE ZONE (HVHZ)
REQUIREMENTS OF THE CURRENT EDITION OF THE FLORIDA BUILDING CODE (FBC). THE PRODUCT DETAILS
CONTAINED HEREIN ARE BASED UPON SIGNED AND SEALED TEST REPORT ATI D1032.01-801-18 AND
ASSOCIATED LABORATORY DRAWINGS.
2. ADEQUACY OF THE EXISTING STRUCTURAL FRAMING AS A MAIN WIND FORCE RESISTING SYSTEM CAPABLE
OF WITHSTANDING AND TRANSFERRING APPLIED PRODUCT LOADS TO THE STRUCTURE IS THE
RESPONSIBILITY OF THE ENGINEER OR ARCHITECT OF RECORD.
3. IN AREAS WHERE WIND-BORNE DEBRIS PROTECTION REQUIREMENTS EXIST, USE OF AN APPROVED IMPACT
PROTECTIVE SYSTEM IS NOT REQUIRED..
4. MATERIALS:
4.1. -SKYLIGHT FRAME MATERIAL: 6063-T5 EXTRUDED ALUMINUM.
4.2. SKYLIGHT INNER AND OUTER DOME MATERIAL: COVESTRO, LLC MAKROLON POLYCARBONATE OR
PALRAM AMERICAS POLYCARBONATE PER THE LATEST MIAMI-DADE NOTICE OF ACCEPTANCE (NOA)
COMPONENT APPROVAL.
5. DESIGNATION "0" STANDS FOR THE A FIXED PANEL
6. IN ACCORDANCE WITH THE CURRENT EDITION OF THE FBC,.WOOD BUCKING SHALL HAVE BEEN
PRESERVATIVE TREATED OR SHALL BE OF A DURABLE SPECIES.
7. DISSIMILAR METALS INCLUDING FASTENERS THAT MAY COME INTO CONTACT WITH ALUMINUM WINDOW
FRAMING SHALL HAVE BEEN PROTECTED IN A MANNER TO PREVENT CORROSION. FASTENERS SHALL BE
MADE OF A CORROSION RESISTANT MATERIAL OR HAVE A CORROSION RESISTANT COATING CONSISTENT
WITH THE REQUIREMENTS OF THE CURRENT EDITION OF THE FLORIDA BUILDING CODE.
INSTALLATION NOTES:
1. ONE (1) INSTALLATION ANCHOR IS REQUIRED AT EACH
2. THE MINIMUM NUMBER OF INSTALLATION ANCHORS -ARE
2.1. AS REQUIRED ON SHEET 3 (CURB MOUNT) At;- � JEI
AND ON CENTER SPACING.
2.2. MINIMUM OF ONE FASTENER PER SIDE AND MINIMUI
ON SKYLIGHT SIZES SMALLER THAN TESTED AND &
3. FOR INSTALLATION OF SELF -FLASHING SKYLIGHT ONTO
SUFFICIENT LENGTH TO ACHIEVE 1 3/8 INCH MINIMUM EP
4. FOR INSTALLATION OF CURB MOUNT SKYLIGHT ONTO W
LENGTH TO ACHIEVE 1 3/8 INCH MINIMUM EMBEDMENT. I
5. FOR INSTALLATION OF CURB MOUNT SKYLIGHT CURB Of
DIAMETER) BOX OR COMMON NAILS OR #6 WOOD SCREI
EMBEDMENT. MINIMUM EDGE DISTANCE IS 5116 INCH.
6. MINIMUM EMBEDMENT AND EDGE DISTANCE EXCLUDE V
FOAM, BRICK VENEER AND SIDING.
7. INSTALLATION ANCHOR CAPACITIES FOR PRODUCTS HE
MINIMUM SPECIFIC GRAVITY OF 0.55. _
8. TOE -NAILING OF CURB MOUNT SKYLIGHT CURB 01� ` "W
FOLLOWING REQUIREMENTS FROM THE 2005 NDS FOR V
8.1. LENGTH (L) AS REQUIRED TO MEET P, Ls AND Lm RE
8.2. MIN. EMBEDMENT (P) IS 2.13" FOR BOX NAILS AND 1.,
8.3. MIN. Ls IS 1.33" FOR BOX NAILS AND 1.0"
FOR COMMON NAILS WITH 0.148" SHANK DIAMETER.
8A. MIN. Lm IS 2.13" FOR BOX NAILS AND 1.6"
FOR COMMON NAILS WITH 0.148" SHANK DIAMETER.
M
N
mtD
II
LL
r
J
Frame
Width = 97.5"
Notes:
1. This skylight is designed to comply with all wind zones, including the HVHZ, of the Florida
Building Code.
2. This skylight meets small & large missle impact resistance (TAS-201%TAS-203)
and no other protection is required.
3. All framing and roof deck is by others and must comply with the Florida Building Code.
4. All sizes equal to or less_ than the test size total square footage are to be accepted
under this NOA.
5. Fasteners used to attach skylight to wood curb are to be minimum #12 stainless
steel wood screws with minimum embedment of 1.37S"
Comer Detail
see Detail #3 & #4)
'op Frame Fastener
#12 X 1.5'
(see BOM #5)
'op Frame Fastener
#10X%"
(see BOM #65
Frame Detail
see Detail #1 & #3)
Angle Detail
;see Detail #1 & #4)
Glazing Detail
see Detail #1 & #2)
Bill of Materials:
1. 6063-TS Extruded Aluminum Frame mitered and welded at four comers. Manufacturer: AFCO Part #4950
2. 6063-TS Extruded Aluminum Angle mitered and welded at four corners. Manufacturer: AFCO Part #4843
3. Dow Coming 795 Silicone Building Sealant located between aluminum angle & glazing (glass bite)
4. 0.125" UV Enhanced polycarbonate domes. Rise varies but is not less than 16%.of the smaller
dimension of the length or width. Test specimen = 10" outer dome & 7" inner dome.
Manufacturer: Covestro or Palram.Amedcas
S. #12 x 1" Stainless Steel Tapping Screw with neoprene gasket. Fasteners located 12" from each comer,
maximum 12" on center. Minimum one fastener per side and minimum four fasteners per skylight.
6. #10 X 0.375" Stainless Steel fasteners 4" from each comer, maximum 12" on center.
7. Schnee -Morehead SM5127 0.6250" X 0.125" Sealant tape.
LoZLL�om
U1 of
0 j5
r, c ► 9
PRODIJCf MV(SFD I
2S omF'Yi1w with t3-s ne ide
Gaii*o coda
Fxpirzrtr lh:.e yUMV—
By
Robert J. Amoiuso. P.E.
Flodda P.E. No. 49752
No
OF
DCM CURB MOUNT - SECTIONS DESIGN PRESSURE = +40psf / -75psf
Detail- #1:
Frame,. Angle & Glazing Section Detail
#12 x 1" Stainless Steel Tapping Screw with neoprene gaskeL
lym
0.125" W Enhanced Polycarbonate Domes. Rise varies
Fasteners located 12" from each comer, maximum 12" on center.
but is not less than 10% of the smaller dimerWon of the
Miriam,, one fastener per side and four fasteners per skylight
length or width. Test Specimen - 10" Outer 8.7" Inner.
1.75" X 1.75" X .060" Extruded Aliminum Retaining, Angle
Dow Coming 795 Silicone Sealant between retaining
angle and top dome. Glazing bite = 1.75"
Schnee Morehead SM 5127 sealant tape. 0.6;
width applied continuously around the permeter
#10 X 0375" stainless steel fastener. 4" from each
Of the dome set
comer, maxmnrm 12" on center.
.060" Extruded Aluminum Shape -
Minimum Stainless Steel #12 PH or HH Wood Screw with minimum 1.375"
Sealant to be minimum 0.125" tall bead to create constant
embedment and 0.875" Edge Distance, 3" from each comer St maximum 8" on
seal between extruded frame and top of crab. (by others
center. Pre -punched 1/8" holes by Maxim for fasteners (by others or optional
or Included by Maxim as per note below)
# aooessary)(See Installation Notes on Sheet 1.)
Curb Buck Exterior Finishing (by others)
Minimum 12D (0.148" Shank Dla.) Common Nail or #6 Stainless Steel Wood
Sam 6" O.C. with Minimum Embeddment of 2.13" and 0.5625" Edge Distance
(by others or optional accessory)(See Installation Notes on Sheet 1.)
Curb 8ukk: See'• Note Below
Roof deck (by others)
* Minimum distance = 4" from aluminum frame to
roof surface for shingles or BUR without insulation.
_
For insulation and'roof tile add Insulation or roof the
•' Roof deck and framing by others. Ail
thickness tc 4" minimum height
roof details shall comply with the Florida
Building Code
** Curb buck = Nominal Southern Yellow Pine
2 X 6 minimum with skylight set on buck with minimum
1/8" tall bead of building sealanL Installation fasteners are
Stainless Steel *12 PH or HH Wood Screw with minimum
1.375" embedment and 0.875" Edge Distance located 3"
,
from each comer and maximum e" on center. This curb
'
buck is an optional component included In the NOA.
Anchoring of the curb buck must be per the Florida
Building Cade. See Installation Notes on Sheet 1.
Detail #2
Glazing Detail
0.125" UV Enhanced Polycarbonate Dome. Rise varies
but Is not -less than 10% of the smaller dimension of
the length or width. Test Specimen = 10".
Schnee Morehead SM 5127 sealant tape. 0.625"
width applied continuously around the perimeter
of the dome seL
0.125' UV Enhanced Polycarbonate Dome. Rise varies
but is not less than 10% of the smaller dimension of
the length or width. Test Specimen = 7".
Detail #3
Aluminum Shape Weld Detail
AFCO Part #AF4950
ML cep h
---.25" ivcep hale
Maintain lip height - at each corner.
no "V" weld acceptable.
Location of Were TIG weld.
4
W
0
m -01
Z
7 CIz
O+•
Or
0� U.
JO Co
WgU.
of
C G�
-a�
Detail #4
PRODUCT REVISED
Aluminum Angle Corner Weld Detail m complying vr'dr the Flo: iSn
AFCO Part #AF-Q43 �"l `°`'` _
ateoro o-]-)e
du
Robert I Pmomso, P.E.
Location of hellare TIG weld. FkAde P.E. No.49752
♦o♦% sPLMES 4
♦ �.
Q' No 49752 -0 %
9'_ STi�;,�u
fn /
In
to
M Ln /
y ti 41
E to rn
II 5
LL t y
01
O
J Q
DL Opening = 92.5"
Frame
Width = 97.5"
X
- Comer Detail
(see Detail #3 & #4)
t— Top Frame Fastener
#12 X 1.5'
(see BOM #5)
f— Top Frame Fastener
#10x%"
(see BOM #6)
Frame Detail
(see Detail #1 & #3)
o
j
2 �
N
OLL
�6
/
Angle Detail
Z
z
(see Detail #1 & #4)
0
(0 Z
G V
zcgo`�'
t1=
o N a
��I
�w¢o�
— Glazing Detail
t 4
F w
R�
(see Detail #1 & #2)
m
Z,
DW
0
to
0:
Notes:
Bill of Materials:
1. This skylight is designed to comply with all wind zones, including the HVHZ, of the Florida
1. 6063-TS Extruded Aluminum Frame mitered and welded at four corners. Manufacturer: AFCO Part #4951
Building Code.
2. 6063-TS Extruded Aluminum Angle mitered and welded at four corners. Manufacturer: AFCO Part #4043
2. ,This skylight meets small & large missle Impact resistance (TAS-201%rAS-203)
3. Dow Coming 795 Silicone Building Sealant located between aluminum angle & glazing (glass bite)
4. 0.125" UV Enhjnced polycarbonate domes. Rise varies but is not less than 10% of the smaller
and no other protection -is required.
dimension of length or width. Test specimen = 10" outer dome & 7" inner dome.
3. Al framing and roof deck is by others and must comply with the Florida Building Code.
erthe
Manufacturer: Americas.
4. All sizes equal to or less than the test size total square footage are to be accepted
S. #12 x 1" Stainless Steel Tapping Screw with neoprene gasket. Fasteners located 12" from each comer,
s Steel T p ingPaiSc
under this NOA.
maximum 12" on center. Minimum one fastener per side and minimum four fasteners per skylight.
S. Fasteners used to attach skylight to the existing roof structure are to be minimum #12 stainless
6. #10 X 0.375" Stainless Steel fasteners 4" from each comer, maximum 12" on center.
steel wood screws with minimum embedment of 1.375"
7. Schnee -Morehead SM5127 0.6250" X 0.125" Sealant tape.
PRi,D'J:1T I:fi'I:NEU I
as comy:.ring wifit the F7oria
ffitti3lirg Ghte , p -, D _a7 .10
FcC&fl¢tet!tt Na � q
.RobertJ.Anw .,P.E.
Florida P.E. No. 49752
No 49752 :O
.0 STATE OF .�!0
pT 4V
idd�rpiu: GPM'
DSF SELF -FLASHING - SECTIONS DESIGN PRESSURE = +40psf / -75psf
'Detail #1:
Frame, Angle & Glazing Section Detail
0.125' W Enhanced Polytarbonate Doman. Rise varies
but Is not less than 10% of the smaller dimension of the
length or width. Test Specimen = 10"-Outer at 7" Inner.
Dow coming 795 Silicone Sealant between retaining
angle and top dome. Glazing bite = 1.75"
Schnee Morehead SM 5127 sealant tape. 0.625"
width applied continuously around the perimeter of
the dome set.
.060" Extended Aluminum Shape
* Minimum distance = 4" from aluminum frame to
roof surface for shingles or BUR without Insulation.
For insulation and roof the add Insulation or roof tile
thickness to 4" minimum height
Detail #2
Glazing Detail
#12 x V Stainless Steel Tapping Screw with neoprene gasket. Fasteners located 12" from
each comer, maximum 12" an cent=. Minimum one fastener per side and four fasteners per
skylight
1.75" X 1.75" X .060" Extruded Aluminum Retaining Angle
#10 X 0.375" stainless steel fastener. 4" from each
comer, maximum 12" on center.
Detail #3
Aluminum Shape Weld Detail
AFCO Part #4951
Minimum
—.25" weep hole
Maintain lip height - at each corner.
no "V" weld acceptable.
Stainless Steel Minimum #12 PH or HH Wood Screw with minimum 1.375"
embedment and 0.875" Edge Distance, 3" from each comer & maximum B" on Location of heliarc TIG weld.
center. Pre -punched 1/8" holes by Maxim for fasteners (See Installation Notes on
Sheet 1.)
Roof deck. (by others)
� I
**Roof deck and framing by others. All
roof details shall comply with the Florida
Building code
0.125" UV Enhanced Polycarbonate Dome. Rise varies
but is not less than 10% of the smaller dimension of the
length or width. Test Specimen = 10".
Schnee Morehead SM 5127 sealant tape. 0.625"
width applied continuously around the perimeter
of the dome set
0.125" UV Enhanced Polycarbonate Dome. Rise wades
but is not less than 10% of the smaller dimension of the
length or width. Tat Specimen = 7".
Detail #4
Aluminum Angle Corner Weld Detail
AFCO Part #4843 .
Location of heliarc TIG weld.
a. a R au9
PRODUCT REVISED I
ns compiyin g with r1w [ 10: ida
bAdh9gC do
Aeeep!ance rt:>!��7, f c
S.igirntioa Dsm 7 �,'' " �
@�dai Dei>�rffSJaci C:inno:
Roberti. Amoroso, P.E.
Florida P.E. No. 49752