The URL can be used to link to this page

Home My WebLink AboutEVALUATION REPORT - UNDERLAYMENTSCertificate of Authorization No. 29824 j 17520 Edinburgh Drive CRE,EK Tampa, FL 33647 TECHNICAL. SERVICES, LLC (813) 480-3421 EVALUATION REPORT FLORIDA BUILDING CODE, 6"" EDITION (2017) Manufacturer: TAMKO BUILDING PRODUCTS, INC. Issued October 19, 2017 P.O. Box 1404 Joplin, MO 64802 (417} 624-6644 http://www.tamko.com Quality Assurance: UL LLC (QUA9625) SCOPE Category: Roofing Subcategory: Underlayments Code Sections: 1507.1.1 Properties: Physical properties i PRODUCT DESCRIPTION TAMKO RO ASTM Slate ASTM D 6380, Class M, Type II underlayment constructed from organic felt saturated Surfaced Rolf Roofing with asphalt and coated on both sides with asphalt and surfaced with granules. TAMKOO ASTM Tile ASTM D 6380, Class M, Type 11 underlayment constructed from an organic felt saturated Underlayment with asphalt then coated on both sides with asphalt and surfaced with granules. i TAMKOkU Master ASTM' ) 6380, Class S, Type IV underlayment constructed from an organic felt saturated Smooth with asphalt then coated on both sides with asphalt and surfaced with a fine mineral. For I use in.non-HVHZ only. :F TAMKOO Moisture Self -adhered, ASTM D 1970; fiberglass reinforced,'; modified bitumen sheet membrane Guard@) with a mineral_, surfacing and, a removable release film on the adhesive side and removable selvedge release tape. TAMKO® No.15 ASTM ASTM;D 226, Type I underlayment constructed from a non -perforated organic felt that is Asphalt Saturated saturated with asphalt. Organic Felt TAMKOO No.. 15 UL ASTM D 226, Type I underlayment constructed from .a non -perforated organic felt that is Asphalt Saturated saturated with asphalt. Organic Felt TAMKO® No. 30 ASTM ASTMD 226, Type.11 underlayment constructed from a non -perforated organic felt that is Asphalt Saturated saturated with asphalt. Organic Felt TAMKO® No. 30 UL ASTM 1D 226, Type II underlayment constructed from a non -perforated organic felt that is Asphalt Saturated saturated with asphalt. Organic Felt TAMKO® TW Metal and Self -adhered, flexible, ASTM D 1970 and TAS 103, .rubberized asphalt sheet membrane Tile Underlayment with a polymer film on the surface and a removable release film on the adhesive side. TAMKOO TW Self -adhered, flexible; ASTM D 1970, rubberized asphalt sheet membrane with a Underlayment polymer film on the surface and a removable release film on the adhesive side. TBP14001A FL12328-R8 1 of 4 This evaluation report is provided for State of Florida product approval under Rule 61 G20�. The manufacturer shall notify CREEK Technical Services, LLC of any productchanges or quality assurance changes throughout'the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein. I CREEKTAMKO BUILDING PRODCUTS, INC. ,+ TAMKO Underlayments �.� -f"Ec$- LAICAL SIZIRVICE: Lt 't TAMK0@ TAM -FELT Alternate to ASTM D 226, Type I and Type 11 underlayment constructed from a non - perforated organic felt that is.saturated with asphalt.. APPLICATION METHOD Installation shall be in accordance with the published manufacturer's installation instructions, the FBC, and the requirements below. Deck substrates shall be clean, dry, and free from any irregularities and debris. All fasteners in the deck shall be checked for protrusion and corrected prior to underlayment application. The roof deck shall be constructed of closely fitted plywood sheathing for new or existing construction. Plywood deck shall be installed in accordance with FBC requirements. Roof decks shall have no more than 1/8" gap at abutting joints. The minimum application temperature shall be 50°F except as follows: a) The minimum application temperature of TAMKO® TW Metal and Tile Underlayment and TAMKOV TW Underlayment shall be 40°F. b) The minimum'application temperature of TAMKO® Moisture GuardO shall be 35°F. The minimum roof slope shall be in accordance with FBC requirements except as.foilows: a) The minimum slope of TA.MKO® ASTM Slate Surfaced Roll Roofing shall be 2:12. Underlayments shall be exposed in accordance with the manufacturer's recommendations, but in no case shall exposure exceed 30 days. Exception: TAMKO() TW-Metal and Tile.Under►ayment may be exposed for a maximum 90 days. Self -adhering underlayments may be adhered to primed or unprimed plywood substrates in the non-HVHZ. All roof coverings shall be mechanically fastened through the underlayment to the roof deck. Allowable Roof Coverinas: Metal Roof Mineral wood Underlayment G.AsphaIt 'Shin les Panels and Shin les Surfaced Roll Roofing Shingles and Shakes Slate Shingles Clay and Concrete Tile TAMKOO ASTM Slate ? 1 Y Surfaced Roll Roofing N N jN N Y TAMKOJASTM Tile Underlayment N N N N N Y TAMKO(§) Master Smooth Y' N N N N N TAMKO® Moisture Guard® Y N N N N N TAMKO® No. 15 ASTM I Asphalt Saturated Organic Y Y Y YZ N N Felt TAMKO@ No. 15 UL Asphalt ff Saturated Organic Felt Y Y Y YZ t Y N TAMKO@ No. 30 ASTM Asphalt Saturated Organic Y Y Y `f Y Y Felt TAMKOrni No. 30`UL Asphalt Saturated Organic Felt Y Y Y N Y N TAMKO® TW Metal and Tile Y Underlayment Y N N N Y TAMKO® iiN Underlayment Y Y N N N N TAMKO(D TAM -FELT Y N N N N N utes. iI open vauey appucauons per -iour,z.v,z 2) Wood shingles only TBP14001.4 FL12328-R8 Page 2 of 4 This evaluation report is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services; LLC of any product changes or quality assurance changes throughoutbe duration for which this report is valid. This evaluation report does not express; nor imply warranty, installation, recommended us4, or other product attributes that are not specifically addressed herein. ;" s� y CREEK TECHNICAL SERVICES, LLB' LuTATms TAMKO BUILDING PRODCUTS, INC. TAMKO Underlayments 1 } Fire Classification is not within the scope of this evaluation. 2) Wind uplift resistance in not within scope of this evaluation. 3) Installation of the evaluated product shall comply with this report, the FBC, and the manufacturer's published application instructions. Where discrepancies exist between these sources, the more restrictive and FBC compliant installation detail shall prevail. 4) Contact the manufacturer when installing at temperatures below the minimum application temperature. 5) Unless otherwise stated, the minimum roof slope shall be in accordance with FBC requirements. 6) All underlayments shall be installed with the roll length parallel to the eave, starting at the eave, and lapped in successive courses installed up the deck in a manner that effectively sheds water from the deck. End laps shall be staggered between courses in accordance with the manufacturer's application instructions. 7) The underlayment may be used as described in other current FBC product approval documents. 8) The underlayment shall not be installed over existing roof coverings. 9) Contact the manufacturer -'regarding specific exposure limits for each underlayment. 10) All products listed in this report shall be manufactured under a.quality assurance program in compliance with Rule 61G20-3. REFERENCES I Enti Report No. PRI Construction Materials Technologies (TST6049) TAP-192-02-01 PRI Construction Materials Technologies (TST6049) TAP-193-02-01' PRI Construction Materials Technologies (TST6049) TAP-214-02-01 PRI Construction Materials Technologies (TST6049) TAP-215-02-01 PRI Construction Materials Technologies (TST6049) TAP-216-02-03 PRI Construction Materials Technologies (TST6049) TAP-217-02-01 REV PRI Construction Materials Technologies (TST6049) TAP-218-02-01 PRI Construction Materials Technologies (TST6049) TAP-219-02-01 PRI Construction Materials Technologies (TST6049) TAP-220-02-01 PRI Construction Materials Technologies (TST6049) TAP-222-02-01 PRI Construction. Materials Technologies (TST6049) TAP-245-02-01 li PRI Construction Materials Technologies (TST6049) TAP-311-02-01 PRI Construction Materials Technologies (TST6049) TAP-019-02-01.1 PRI Construction Materials Technologies (TST6049) TAP-387-02-01 PRI Construction Materials Technologies (TST6049) TAP-388-02-01 UL LLC (TST9628) 13CA12269 Standard ASTM D 1970 ASTM D 1970 ASTM D 4869 ASTM D 226 ASTM D 6380 ASTM D 6380 ASTM D 226 ASTM D 226 ASTM D 6380 ASTM D 4869 TAS 103 ASTM D 4798 ASTM D 1970 ACC 188 ASTM D 1970 ASTM D 1970 ASTM D 226 ;t TBP14001.4 FL12328-R8 This evaluation report is provided for State of Florida product approval under Rule 61G20- Technical Services, LLC of any productchanges or quality assurance changes throughout This evaluation report does not express nor imply warranty, installation, recommended_ us specifically addressed herein. Year 2015a 2015a 2016 2009 2003(2013) 2003(2013) 2009 2009 2003(2013) 2016 1995 2011 2015a 2012 2015a 2015a 2009 3of4 The manufacturer shall notify CREEK e duration for which this report is valid. or other product attributes that are not ,i CREEK TAMKO BUILDING PRODCUTS, INC. TAMKO Underlayments TECHNICAL 'CI S, LLC COMPLIANCE STATEMENT The products evaluated herein by Zachary R. Priest, P.E. have demonstrated, compliance with the Florida Building Code, 6`h Edition (2017) as evidenced in the referenced documents submitted by;the named manufacturer. No 74021 ' / ; 12:15:58 P � • • � .a ' _0 '00' :3 STATE OF •:��` R ; O p;•'\rti4'°` °®,, Zachary; R. Priest, P.E: S�; ' •.. • •� ` Florida Registration No, 74021 Organization Ai 1 bea' No. ANE9641 CERTIFICATION OF INDEPENDENCE u= CREEK Technical Services, LLC does not have;. nor will it acquire, a financial interest in any company manufacturing or distributing products under this evaluation. CREEK Technical Services, LLC is not owned, operated, or controlled by any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E. does not have, nor will acquire, a financial interest in any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E: does not have, nor will acquire..a financial interest in any other entity involved in the approval process of the product. i; END OF REPORT TBP14041.4 FL12328-R8 Page 4 of 4 This evaluation report is provided for State of Florida product approval under Rule 6IG20-3. The manufacturer shall notify CREEK Technical Services, LLC of any product changes or quality assurance changes throughout the.duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.