HomeMy WebLinkAboutNOAMIA(�, NDMIANII-DARE COUNTY
® COPY PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 31525-99
NOTICE OF ACCEPTANCE (NOA) www.miamidade.sov/economy
CeriainTeed Corporation
20 Moores Road LNOV �01$ SCANNED
Malvern, PA 19355 �� �®
r►t'a l'arRl� 4-0,
SCOPE: — St LUcle County
This�NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used! in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This INOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This ,product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION--Certa nTeed-,ModifedBitnmen:Roofmg.-Sys emsroverWooa I?ecl�s s
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
I
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
i
ADVERTISEMENT: The NOA number preceded by the words Miami Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA #14-0529.02 and consists of pages 1 through 42.
The submitted documentation was reviewed by Alex Tigera.
� ("L rTOA�No_ wIT'1003`u-.-
Mu 4naoe courmr xpira`tion DaT te: 0 /_19t23"i
Approva_I_tD_a_te: 0.4/119/18t• Page 1 of 42 :
ROOFING SYSTEM APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Material:
APP/SBS
Deck Type:
Wood
Maximum Design Pressure:
-127.5 psf.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Description
All Weather/Empire Base
39 3/s" x 65' 10' ;
ASTM D 4601, Type Asphalt coated, fiberglass reinforced
Sheet
Roll weight: 70 lbs.
II
base sheet.
(2 squares)
UL Type G2
Flexiglas Base Sheet
39 3/s" x 98'9"; Roll
ASTM D 4601, Type
Modified Bitumen coated fiberglass
weight: 90 lbs.
II
base sheet.
(3 squares)
UL Type G2
Flint�astic Base 20
39 3/s" x 49' 6"; Roll
ASTM D 6163,
Modified Bitumen coated fiberglass
weight: 90 lbs.
Grade S, Type I
base sheet.
(1.5 squares)
Flintglas Ply Sheet Type IV
39 3/8" x 1647% Roll
ASTM D 2178, Type
Fiberglass, asphalt impregnated ply sheet.
weight: 38 lbs.
IV
(5 squares)
UL Type GI
Flintglas Premium Ply Sheet
39 3/s" x 164'7"; Roll
ASTM D 2178, Type Fiberglass, asphalt impregnated ply
Type!VI
weight: 40 lbs.
VI
sheet.
(5 squares)
UL Type GI
Flintlastic STA
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Smooth surfaced APP Modified
weight: 871bs.
Grade S, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
luitlasti GTc A
39 3/s' x 32' 10"• Roll
ASTM D 6222
Granule. surfaced APP Modified,
weight: 1051bs.
Grade G, Type I
$iumen meml�ane�with non woven
(1 square)
i r � s �,"''"'?
ggolyesterjmat�remforcemen for torch
Flintlastic GTA-FR
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 94 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application.
NOA No.: 17-1003.04
MIMMADE coExpiration Date: 06/19/23
Approval Date: 04/19/18
Page 2 of 42
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
I TABLE 1
Product
Test
Dimensions Specification
Product
Description
Flintlastic FR-P
39 3/g' x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic Premium FR-P
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic FR Dual Cap
39 3/8" x 32' 10"; Roll
ASTM D 6162,
Granule surfaced SBS modified
weight: 103 lbs.
Grade G, Type I
bitumen membrane with a nonwoven
(I square)
polyester/fiberglass composite mat
reinforcement for use in cold or mop
applications.
Flintlastic FR Cap 30
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 86 lbs.
Grade G, Type I
Modified Bitumen membrane with
(I square)
fiberglass mat reinforcement for mop
applications.
Flintlastic FR Cap 30 T
39-3/8" x 32' 10"; Roll
ASTM D 6163,
Granule surfaced SBS Modified
weight: 100 lbs.
Grade G, Type I
Bitumen membrane with fiberglass
(I square)
mat reinforcement for torch
application.
FlintlIastic Base 20 T
39-3/8" x 33'; Roll
ASTM D 6163,
Modified Bitumen, coated fiberglass
Weight: 81 lbs.
Grade S, Type I
base sheet for torch application.
(1 square)
Flintlastic FR Cap 30 CoolStar
39 3/s" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 88 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
Flintl'astic FR Cap 30 T
39 3/s' x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
CoolStar
weight: 102 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
Flintlastic GTA CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 106 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
I
CMIAMMA E COUNTY
I
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 3 of 42
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
i Product
Dimensions
Specification
Description
Flintlastic GTA FR CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 106 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
Flintlastic GMS CoolStar
39 3/s' x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 97 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application. Covered with reflective
CoolStar Coating.
Flintlastic FR-P CoolStar
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 103 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
Flintlastic Premium FR-P
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
Cool$tar
weight: 103 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
Flintl'astic Ultra Poly SMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Smooth surfaced SBS Modified
Base Sheet
weight: 901bs. (1
Grade S, Type I
Bitumen Membrane with non -woven
squares)
polyester mat reinforcement for mop
applications.
G asta ise:Base�'S_ heet ,
36" x 98' 9' ; Roll
ASTM D 4601, Typ!E Asphalt coated beiglass base shee
weight: 75 lbs.
(3 squares)
UL Type G2
Flintlastic Poly SMS Base
39 3/8" x 64' 3"; Roll
ASTM D 4601,
Modified Bitumen coated polyester
Sheen,
weight: 90 lbs.
Grade S, Type II
base sheet.
(2 squares)
UL Type G2
Yosemite Venting Base Sheet
39 3/8" x 32' 10"; Roll
ASTM D 3909
Mineral Surfaced fiberglass reinforced
weight: 851bs.
ASTM D 4897, Type buffer sheet.
(1 square)
II
UL Type G3
Flintlastic APP Base T
39 3/8" x 65' 4"; Roll
ASTM D 6509
Modified Bitumen coated fiberglass
weight: 100 lbs.
base sheet.
(2 squares)
I
NOA No.: 17-1003.04
MIAMFDADE COUNTY Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 4 of 42
Flintlastic Ultra Glass SA
Black DiamondTM Base Sheet
APPROVED INSULATIONS:
I
Product Name
FlintBoard ISO
F1intBoardx ISO
ACFoam -11
DensDeck
I
DensDeck Prime
39 3/s" x 33' 11 "; Roll
weight: 73 lbs.
(1 square)
36" x 687'; Roll
weight: 781bs.
(2 squares)
ASTM D 1970
ASTM D 1970
TABLE 2
Product Description
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Water resistant gypsum board
Water resistant gypsum board
H-Sh eld
Polyisocyanurate foam insulation
ENRGY 3
Polyisocyanurate foam insulation
ENRGY 3 25 PSI
Polyisocyanurate foam insulation
Multi 1- Max FA-3
Polyisocyanurate foam insulation
SECUROCK Gypsum -Fiber Roof Board
homogenous fiber reinforced
Structodek High Density Fiberboard
High Density Wood Fiber Insulation
Roof Insulation
board
FescoBoard
Expanded perlite and fiber insulation
I
CMWDADE COUNTY
A �
Self -adhering, fiberglass reinforced,
SBS modified`bitumen base/ply sheet.
Self -adhering fiberglass reinforced
modified bitumen base sheet
Manufacturer
(With Current NOA)
CertainTeed Corporation
C6rtainTeed Corp.
Atlas Roofing Corp.
Georgia Pacific Gypsum LLC
Georgia Pacific Gypsum LLC
Hunter Panels LLC
Johns Manville Corp.
Johns Manville Corp.
RMax Operating, LLC
USG Corp.
Blue Ridge Fiberboard, Inc.
Johns Manville Corp.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 5 of 42
i
APPROVED FASTENERS:
I
Fastener Product
NuT Name
11. Trufast #12 DP Fastener
21.
Trufast 3" Metal
Insulation Plate
3.
FlintFast #12
4!
FlintFast 3" Insulation
Plate
5�
FlintFast #14
I
6.
Simplex MAXX Cap
71
OMG #12 Standard
Roofgrip
8.
OMG 3" Galvalume Steel
Plate
9.
Trufast #14 HD Fastener
10. OMG Heavy Duty
11.
3 in. Round Metal Plate
12.
AccutTrac Hextra
13.
AccuTrac Plate
14.
AccuTrac Flat Bottom
i
Plate
15.
Millennium One Step
Foamable Adhesive
16.
Millennium PG-1 Low
Viscosity Insulation
Adhesive
17.
Insta Stik Quik Set
Insulation
PAOVE
OUNTY
•
TABLE 3
Product
Description
Insulation fastener for wood
and steel decks
Galvalume steel plate
Coated, carbon steel screw
Galvalume AZ50 steel plate
Insulation fastener for wood
and steel decks
Polymer fastner
Insulation fastener for wood
and steel.
Galvalume stress plate
Insulation fastener for wood
and steel decks
Insulation and membrane
fastener
Galvalume AZ50 steel plate
Carbon steel fastener
Galvalume stress plate.
A2-SS aluminized steel plate
Manufacturer
Dimensions
(With Current NOA1
various
Altenloh, Brinch & Co. U.S.,
Inc.
3" round
Altenloh, Brinch & Co. U.S.,
Inc.
various
CertainTeed Corp.
3" round
CertainTeed Corp.
various CertainTeed Corp.
1" long Simplex Nails, Inc.
various OMG, Inc.
3" round OMG, Inc.
various Altenloh, Brinch & Co. U.S.,
Inc.
Various OMG, Inc.
3" round OMG, Inc.
Various OMG, Inc.
3" square OMG, Inc.
3" square OMG, Inc.
Polyurethane two component
1.5 liters
Adco Products, Inc. d.b.a.
high rise insulation adhesive
Royal Adhesives & Sealants,
Inc.
Polyurethane two component
1.5 liters
Adco Products, Inc. d.b.a.
low rise insulation adhesive
Royal Adhesives & Sealants,
Inc.
Polyurethane one component
It is supplied
The Dow Chemical Company
moisture curing adhesive
in pressurized
cylinders with
a net weight
of 23 lbs.,
with a total
unit weight of
30 lbs.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 6 of 42
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
(With Current NOA)
118.
OMG OlyBond 500
Spray polyurethane foam
10 gal. bag -in-
OMG, Inc.
Adhesive
insulation adhesive
box set and
1.5 liters
SpotShot
1
cartridge
19.
OMG OlyBond 500 Green
Spray polyurethane foam
10 gal. bag -in-
OMG, Inc.
Adhesive
insulation adhesive
box set and
1.5 liters
SpotShot
cartridge
APPROVED SURFACING/COATING OPTIONS:
i
TABLE 4
Chosen components must be applied according to manufacturer's application instructions. Any coating, listed
below, used as a surfacing, must be listed within a current NOA.
System Number Manufacturer Application
I. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at
i
2. Generic
3. Karnak Corp.
1
4. CertainTeed Corp.
5. Gardner Asphalt Corp.
1
6, Gardner Asphalt Corp.
CMIAMMADECOUNTY
I
60 lbs/sq.
Slag applied at 3001bs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
F1intCoat A-150 applied at an application rate of 1.5 gal/sq.
APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
APOC #400 Sunbrite applied at an application rate of 3 gal./sq.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 7 of 42
EVIDENCE SUBMITTED:
Test Agencv/Identirier
Name
Report
Date
Factory Mutual Research Corp.
FM 4470
3Y8A'LAM
03/23/96
FM 4470
OD3A3.AM
04/04/97
FM 4470
2DOAO.AM
12/23/98
FM 4470
1 D7A4.AM
11 /09/98
FM 4470
3039046
06/15/10
FM 4470
3048520
09/19/13
Underwriters Laboratories, Inc..
UL 790
R11656
01/11/13
Unit-d States Testing Company
ASTM D 5147
97457-4
06/03/88
I
ASTM D 5147
97-457-2R
12/02/87
Momentum Technologies, Inc.
ASTM D6164
AX31 G8F
06/05/09
TrinityIERD
TAS 114(J)
3507.08.99-1
04/18/01
TAS 114(J)
3504.06.01-1
06/05/01
TAS 114
3521.07.04
07/29/04
TAS 114
3533.01.06
01/06/06
TAS 114 (H)
Letter
04/05/06
TAS 117 (B)
3503.10.06
10/10/06
TAS 117 (B)
06490.04.07-R1
06/27/07
TAS 117 (B)/ ASTM D 6862
C8500SC.11.07
11/30/07
TAS 114
C8370.08.08
08/19/08
FM 4470, TAS 114, FM 4470,
C8370.08.08-R1
10/05/09
TAS 114(J)
-
ASTM Physical Properties
C10080.09.08-R4
03/25/10
TAS 114(H), TAS 117(B), TAS
C30560.06.10
6/10/10
114(J)
FM 4470, TAS 114
C32830.07.10
7/20/10
ASTM D6164/D4798
C31410.01.11-2
01/10/11
TAS 117B
C35500.02.11
02/09/11
ASTM D4601
C40050.09.12-1
09/28/12
ASTM D1876
C35460.05.11
06/16/11
ASTM D1876, TAS 114 (H),
C42110.08.12
08/13/12
TAS 117 (B)
FM 4474/TAS 114
C39670.08.12
08/20/12
ASTM D1970
c4o05O.O9.12-2
09/28/12
ASTM 135147/134798
C31410.10.10-R1
11/01/12
ASTM D5147/D4798
C31410.01.11-1-R1
11/01/12
ASTM D4798
C31410.01.11-2A Rl
02/21/13
ASTM D4798
C31410.12.13
12/05/13
ASTM D6222
C40050.12.13-R1
12/31/13
TAS 117, TAS 114
C30310.12.09-R1
03/07/14
ASTM D1876, TAS 114 (H),
C45620.03.14
03/27/14
FM 4474
ASTM D1876, TAS 114 (IT),
C47320.03.14-R1
04/01/15
FM 4474
NOA No.: 17-1003.0.4
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 8 of 42
EVIDENCE SUBMITTED:
i Test Agency/Identifier
Name
Report
Date
ASTM D4601-04 (2012), Type II
CTR-SC11145.09.16-
09/19/16
3A
I
PRI Construction Materials.
ASTM D6163
CTC-066-02-01
08/09/11
Technologies LLC
ASTM D6222
CTC-071-02-01
08/08/11
ASTM D6222
CTC-070-02-01
08/09/11
ASTM D6164/D4798
CTC-093-02-01
08/09/11
ASTM D4601
CTC-126-02-01
03/12/12
ASTM D2178
CTC-122-02-01
03/13/12
ASTM D2178
CTC-123-02-01
03/13/12
ASTM D4601
CTC-127-02-01
03/13/12
ASTM D6163
CTC-128-02-01
06/11/12
ASTM D6163
CTC-129-02-01
06/11/12
ASTM D6164
CTC-132-02-01
06/11/12
ASTM D6164
CTC-161-02-01
05/09/13
ASTM D6162
CTC-183-02-01
10/02/13
ASTM D6164
CTC-190-02-01
12/02/13
ASTM D1970
CTC-199-02-01
01/22/14
ASTM D6163
CTC 319-02-01
08/22/17
i
i
CUkADE COUNTY
UM
I -
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 9 of 42
Membrane Type: tYPP IVSadfe
i
Deck Type 1:Woo Non -Insulate; `�'
Deck Description: '9/32 Tr,- - ater plywood ot_vaood=plank, attached w h: S - ng hank nails spaced 4".,.o:c t
14odj611sts.spacednaximum2d' o�c�
System Type E(6): Base'she mechanically:fastenetl t
All General and System Limitations apply.
I
"aseSheet
Past ping:
I
Ply Sheet:
(Optional)
I
apsRt8`a c nrntlie lap :and thee rows.'staggered in the center of tfie sheet 8770:c.
One ply of All Weather/Empire Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase
Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. or one
ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self -adhered or Flintlastic STA
or Flintlastic APP Base T torch adhered.
mbra� liiitlasg—e-GT lintlastic GTA CoolStar, Flintlastic GTA FR or Flintlastic GTA-FR CoolStar
torch adhered to base/ply sheet.
Surfacing:
(OptI ional)
Any of the approved surfacing/coating options listed in Table 4.
Maximum Design �-40 psf.— See�eneral-iimfftion # n-
Pressure:
NOA No.: 17-1003.04
M[AMI-oaDe COUNTY Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 26 of 42
WOOD DECK SYSTEM LDmATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
I. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. 'Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped' If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design'pressure of -45 psE
5. ;Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
,fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
Iprepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered
Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value
taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application
Standard PAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet ' as calculated in compliance with .Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and comers). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended comers and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 17-1003.04
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 42 of 42