HomeMy WebLinkAboutLAB TEST RESULTSCONSTRUCTION MATERIALS
TECHNOLOGIES
LABORATORY TEST RESULTS
Report for: Woodland Industries SCAB NEE)
1520 Kalamazoo Drive BY
Griffin, GA 30224 St. Lucie County
Attention: Bill Ward
Product Name(s): No. 30
Manufacturer: Woodland Industries
PRI-CMT Project No.: WII-008.02-03
Source: Woodland Industries
Date Received: May 12, 2017
Sep. 13, 2017
Dates Tested: May 16 — Sep. 15, 2017
Purpose: Evaluate No. 30 for compliance with the physical properties of ASTM D 226
Asphalt -Saturated Felt Used in Roofing and Waterproofing, Type 11.
Test Methods: Testing was completed as described in ASTM D 226-09: Standard Specification
for Asphalt -Saturated Organic Felt Used in Roofing and Waterproofing. Test
methods assigned or referenced include ASTM D 70: Standard Test Method for
Density of Semi -Solid Bituminous Materials (Pycnometerldethod); ASTM D 146:
Standard Test Methods for Sampling and Testing Bitumen -Saturated Felts and
Woven Fabrics for Roofing and Waterproofing; and ASTM D 6136: Standard
Test Method for Kerosine Number of Unsaturated (Dry) Felt by Vacuum Method.
Sampling: Product samples were provided by Woodland Industries from Griffin, GA.
i ne �t resmw, upimuns, or inmrpremuons are oases on me mamroa suppiieo oyme cnent. i nis report Isrorme excwslve use of stated
client No reproduction orfaesimile In anyform can be madewithoutthe client's permission. This reportshall not be reproduced exceptin
full without the written approval ofthis laboratory. PRI Construction MatedalsTechnologles LLC assumes no responsibility nor makes a
performance orwarranty statement for this material or products and processes containing this material In connection with this report
PRI Conehudlon Materials Terrinologio LLC 6408Badgermdw Tampa,FL33810 Ta1:813.621d777 F=85Q14M emm1:metadalstssW0p4=tmm WelAltshepik".priontwm
Woodland Industries
ASTM D 226 for
No. 30
Page 2 of 3
Breaking Strength (Ibf/in-width)
20 specimens; 1" x 6" x thickness;
ASTM D 146
Cond. 2h @ 73.4t3.6*F & 50t5%RH;
Test @ 73.4t3.60F• Rate=2in/min
Longitudinal (with fiber grain)
66
a 30
a 40
Transverse (across fiber grain)
29
z 15
a 20
Pliability(Pass/Fail] .
10 specimens; V x S" x thickness;
Cond. 10-15min in water @ 77±1:80F;
ASTM D 146
'/" radius
'/a" radius
Test 90° around %z' radius In 2s
Longitudinal (with fiber grain)
Pass
No; Failures
No Failures
Transverse (across fiber grain)
Pass
No; Failures
No Failures
Loss on Heating (weight %)
2 specimens; 12" x 6" x thickness;
ASTM D 146
2
5 4
5 4
Test Cond. 221d:5°F for 5h±3min
ft=. zsr s--?`Y t e Tr qp �<. a
DImenslona and Masses
FA.^x _... t^__ r_ _. ,.x. ..aa..!i t... ...,a.. _. .
:.cs , ate.._.
.,. �Y;:...+ _�.v.C.•.
Width of Roll (in) ASTM D 146 35 718
" 36d 1'/4
36t1/4
Area, min (ftz)
ASTM D 146
216
432
216
Moisture at Point of Manufacture (%)
ASTM D 146
NT
64.3
5 4.1
As Received'
3.2
5.4.3
54.1'
Net Mass of Saturated Felt (lb/100ft2)
ASTM D 146
26
211.5
Z 26
Mass of Saturant (lb/100ft2)
ASTM D 146
17.5
2 6.2
z 15.0
Mass Ratio of Saturant to Desaturated Felt
ASTM D 226
1.5
a 1.2
a 1.5
Saturation Efficiency (%)
ASTM D 226
NA
' 70
Mass of Desaturated Felt (Ib/100ft2)
ASTM D 146
11.4
2 5.2
a 10.0
Ash (%)
ASTM D 146
5.0
.510.0
s 10.0
Continued on Following Page
client. No reproduction orfacsimile in anyfonn can be i
full without the written approval of this laboratory. PRI(
performance or warranty statement for this matedal or
he clients Permission. Thisreportshallnotbereproducedexceptin
latedatsTechnologies LLC assumes no responsibility nor makes a
processes containing this material In connection with this report
PRIConahuCft Materials Te*WOgles LLC 84888adgar Drive Tampa,FL33818 Tel:81340.5 n Fax;813E21h840 email: meterialstaelBt@pdemtwm WebBite:http•J/sw,xpdmtwm
Woodland Industries
ASTM D 226 for
No. 30
Page 3 of 3
Perforated Felt (in2) I ASTM D 226 I NA I s 0.05
Average Venting Area (%) ASTM D 226 NA a 0.1
Unrolling @ 50°F and 140°F [PasVFail] I ASTM D 226 I Pass I No Damage I No Damage.
Note(s): 1- Moisture (As Received) was utilized In lieu of Moisture at Point of Manufacture;
NT- Not Tested;
NA- Not Applicable
Statement of Compliance:
The productwas tested has demonstrated compliance with the physical requirements of Type Il prescribed in
ASTM D 226-09: Standard Specification for Asphalt -Saturated Organic Felt Used in Roofing and
Waterproofing.
Signed: -...
Florida
Date: C
Report Issue History:
Issue # I Date
h
END OF REPORT
upaauos, or merpremaons are oaseo on the material supplied bythe client. This report isfor the exclusive use of stated
client. No reproduction orfacsimile in anyform can be made without the client's permission. This reportshail notbe reproduced exceptin
full without the written approval of this laboratory. PRI Construclion Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material In connection with this report.
PRIComsWc0m Materials Technologies LLC 640813atpar Drive Tampa,FL33610 Tel: 813-621-SM F=813.621-6840 eanali:maWalstesling@pricmt= WebSIbxhBpJNranv.pfl=t n