The URL can be used to link to this page

Home My WebLink AboutINSTALLATION PAPERWORKi-;-MfS�LVER T eyNF® 4�/e � ;��lthelie Roo �nde�layment !_- I Installation Instructions: i Caution: Always follow Safety Instruction, Building Codes and Safe Work Practices �- issues bythe local Govt. bodies (e.g.OSHA / WCB) i t{_ FT Synthetics products should be installed with Plastics Cap or Metal Cap nails with either ring shank I `,• - or smooth shank Nails. DO NOT USE STAPLES. Use of staples will void the Manufacturer's warranty. FT Synthetics products are a secondary layer protection approved for installation over Plywood with ' �.„ proper fasteners. FT Synthetics underlayment is an air, vapour and water barrier with <1 Perm. FTSynthetics underlayment is laid out horizontally with printed side up using 6" vertical laps and 4" ' horizontal laps. The overlaps ensure that the water runs over the overlaps without getting under the material. Before installing the underlayment ensure that the roof is clear of any debris or any sharp protrusions. 6 r ; Pro ductmust be attached to the roofing structure using 1" plastic or metal cap nails. Product must be fastened with the nail pattern printed on the product. All anchoring must be performed flush to the I C! roof, 90 degrees to the roof deck that will hold the material tightly with the plywood. The use of every-• ; 1 other anchoring location printed on the product is also acceptable. For prolonged exposure, double the overlaps and use every anchor location. Product has 90 Days UV protection but it should not be considered a final roofing system. A proper final roofing system should be installed over the product ' to et the proper protection. Product is a secondary barrier used over plywood, under a roofing 9 P P P Y P Y g system like wood and asphalt shingles and metal. Ly4 Safety Notification: ; } FT Synthetics products are designed with the GRIPSPOT technology for better skid protection for the `- roofer but product may become slippery due to high moisture, frost, rain, water, dust, debris or other a conditions. Use precautions when working on the roof. Follow all local and federal safety codes when "n i . installing any roofing system including FT Synthetics products.Failure to adhere to those procedures may resultinserious lnjuryorevendeath, .? ' 9 1 ~" Unit 143120 - 76th Avenue Toll Free Ph: 1-844.353-9839 M FT SYNTHETICS Surrey BC V3W 3H8 Phone: 604.594.3439 q , i ' Fax: 604-594.3589 Canada w .ffsynxom '`t Single Layer application of FT SILVER For slopes greater that 4:12 FT SILVER should be installed horizontally starting from the bottom -of the roof with a 4 inch overlaps working up the roof. oof Deck- 1 (100 mm) Rake Drip Edge -- Horizontal Overlap, - Over ---- Underlayment 48" (122 cm) Fasten underlayment as specified in the 6" (150 mm) installation instructions Vertical Overlap Eave Drip Edge Under Underlayment Double Layer Application of FT SILVER For slopes 2:12 to 4:12 FT SILVER should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. `�` lam....... oRoof Deck—� J48" (122 cm) ------ 'Rake Drip Edge Over -- 25" (64 cm) Underlayment 251' (64 cm) Fasten underlayment as specified in the installation instructions Eave Drip Edge Under Underlayment I �I�I �� w� i� �� i �• w w Lull+ 1_1319A - Mh wonun Toll Free Ph- 1.H".M51Ae30 11. F> U r I J 1IV 117C I I LPQ Surrey BC V3W 3H8 Phone: 604-594.3439 Fax: 604-594.3589 Canada w .Asyn.com -2- F/V1 GOLD Synthetic Roofing Underlayment Installation Instructions: Caution: Always follow Safety Instruction, Building Codes and Safe Work Practices issues by the local Govt. bodies (e.g. OSHA / WCB) FT Synthetics products should be installed with Plastics Cap or Metal Cap nails with either ring shank or smooth shank Nails. DO NOT USE STAPLES. Use of staples will void the Manufacturer's warranty. FT Synthetics products are a secondary layer protection approved for installation over Plywood with proper fasteners. FT Synthetics underlayment is an air, vapour and water barrier with <1 Perm. FT Synthetics underlayment is laid out horizontally with printed side up using 6" vertical laps and 4" horizontal laps. The overlaps ensure that the water runs over the overlaps without getting under the material. Before installing the underlayment ensure that the roof is clear of any debris or any sharp protrusions. Product must be attached to the roofing structure using 1" plastic or metal cap nails. Product must be fastened with the nail pattern printed on the product. All anchoring must be performed flush to the roof, 90 degrees to the roof deck that will hold the material tightly with the plywood. The use of every other anchoring location printed on the product is also acceptable. For prolonged exposure, double the overlaps and use every anchor location. Product has 180 Days UV protection but it should not be considered a final roofing system. A proper final roofing system should be installed over the product to get the proper protection. Product is a secondary barrier used over plywood, under a roofing system like wood and asphalt shingles, tiles, slate and metal roof. Safety Notification: Fr Synthetics products are designed with the GRIPSPOT technology for better skid protection for the roofer but product may become slippery due to high moisture, frost, rain, water, dust, debris or other conditions. Use precautions when working on the roof. Follow all local and federal safety codes when installing any roofing system including FT Synthetics products. Failure to adhere to those procedures may result in serious injury or even death. lFruffll FT SYNTHETICS UnlSurrey SC V3W 3H8nue Canada Toll Free Ph: 1.844-353.9839 Phone: 604-594.3439 Pax: 604.594.3589 w .Reyn.com -3- Single Layef- Application of FT GOLD For slopes greater that 4:12 FTGOLD should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. take Drip Edge )ver Jnderlayment n underlayment ecified in the lation instructions Eave Drip Edge Under Underlayment Double Layer Application of FT GOLD For slopes 2:12 to 4:12 FT GOLD should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. Drip Edge dayment derlayment ed in the n instructioi Eave Drip Edge Under Underlayment FT SYNTHETICS Unit 1-13120 - 76th Avenue Toll Free Phi 1.844.353.9839 Surrey BC V3W 3HB Phone: 604-594.3439 Far 694-5943589 Canada w .ftsynxorn -4- ❑O PLATINUM Synthetic Roofing Underlayment Installation Instructions: Caution: Always follow Safety Instruction, Building Codes and Safe Work Practices issues by the local Govt. bodies (e.g. OSHA / WCB) FT Synthetics products should be installed with Plastics Cap or Metal Cap nails with either ring shank or smooth shank Nails. DO NOT USE STAPLES. Use of staples will void the Manufacturer's warranty. FT Synthetics products are a secondary layer protection approved for installation over Plywood with proper fasteners. FT Synthetics underlayment is an air, vapour and water barrier with <1 Perm. FT Synthetics underlayment is laid out horizontally with printed side up using V vertical laps and 4" horizontal laps. The overlaps ensure that the water runs over the overlaps without getting under the material. Before installing the underlayment ensure that the roof is clear of any debris or any sharp protrusions. Product must be attached to the roofing structure using 1" plastic or metal cap nails. Product must be fastened with the nail pattern printed on the product. All anchoring must be performed flush to the roof, 90 degrees to the roof deck that will hold the material tightly with the plywood. The use of every other anchoring location printed on the product is also acceptable. For prolonged exposure, double the overlaps and use every anchor location. Product has 180 Days UV protection but it should not be considered a final roofing system. A proper final roofing system should be installed over the product to get the proper protection. Product is a secondary barrier used over plywood, under a roofing system like wood and asphalt shingles, tiles, slate and metal roof. Safety Notification: Fr Synthetics products are designed with the GRIPSPOT technology for better skid protection for the roofer but product may become slippery due to high moisture, frost, rain, water, dust, debris or other conditions. Use precautions when working on the roof. Follow all local and federal safety codes when Installing any roofing system including FT Synthetics products. Failure to adhere to those procedures may result in serious injury or even death. IFIFFIFT SYNTHETICS unlSurrey BC V3W 3H8nue Canada Toll Free Ph: 1-844353.9839 Phone: 604.594.3439 Fax: 604-594.3589 w .Rsyn.com -5- Single Layer Application of FT PLATINUM For slopes greater that 4:12 FT PLATINUM should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. 6"(150 mm) Vertical Overlap Eave Drip Edge Under Underlayment Rake Drip Edge Over Underlayment Fasten underlayment as specified in the installation instructions Double Layer Application of FT PLATINUM For slopes 2:12 to 4:12 FT PLATINUM should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. FT SYNTHETICS um iaicu im"Avenue ionrreern:i•aa4-ss�•s6ss Surrey BC V3W 3H8 Phone: 604-5943439 Fax: 604-6943589 Canada w .keyn.eom -6- � HYDRA Breathable Synthetic Underlayment Installation Instructions: Caution: Always follow Safety Instruction, Building Codes and Safe Work Practices issues by the local Govt. bodies (e.g. OSHA / WCB) FT Synthetics HYDRA should be installed with Plastics Cap or Metal Cap nails with either ring shank or smooth shank Nails. DO NOT USE STAPLES. Use of staples will void the Manufacturer's warranty. FT Synthetics HYDRA is a secondary layer protection approved for installation over Plywood with proper fasteners. FT Synthetics HYDRA underlayment is laid out horizontally with printed side up using 6" vertical laps and 4" horizontal laps. The overlaps ensure that the water runs over the overlaps without getting under the material. Before installing the underlayment ensure that the roof is clear of any debris or any sharp protrusions. Product must be attached to the roofing structure using 1" plastic or metal cap nails. Product must be fastened with the nail pattern printed on the product. All anchoring must be performed flush to the roof, 90 degrees to the roof deck that will hold the material tightly with the plywood. The use of every other anchoring location printed on the product is also acceptable. For prolonged exposure, double the overlaps and use every anchor location. Product has 180 Days UV protection but, it should not be considered a final roofing system. A proper final roofing system should be installed over the product to get the proper protection. Product is a secondary barrier used over plywood, under a roofing system like wood and asphalt shingles and metal. Safety Notification: FT Synthetics products are designed with the GRIPSPOT technology for better skid protection for the roofer but product may become slippery due to high moisture, frost, rain, water, dust, debris or other conditions. Use precautions when working on the roof, Follow all local and federal safety codes when installing any roofing system including FT Synthetics products. Failure to adhere to those procedures may result in serious injury or even death. ® FT SYNTHETICS UniSurrey BC V3W 3H8nue Toll Free Ph: Phone:; 60.594.348444353.9839 39 Fax: 604-594-3589 Canada w .hsyn.com -7- Single Layer Application of FT HYDRA For slopes greater that 4:12 FT HYDRA should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. Rake Drip Edge Over Underlayment Fasten underlayment as specified in the 6" (150 mm) installation instructions Vertical Overlap Eave Drip Edge Under Underlayment Double Layer Application of FT HYDRA For slopes 2:12 to 4:12 FT HYDRA should be installed horizontally starting from the bottom of the roof with a 4 inch overlaps working up the roof. fake Drip Edge 7ver Jnderlayment !n underlayment lecified in the Ilation instructions Eave Drip Edge Under Underlayment Unit 1-13120 - 76th Avenue Toll Free Ph: 1.844-353.9839 ❑lfr FT SYNTHETICS Surrey BC V3W 3H6 Phone; 604-594-3439 Fax: 604.594.3589 Canada w .ksyn.com -8-