The URL can be used to link to this page

Home My WebLink AboutTEST REPORTIntertek Architectural Testing TEST REPORT Report No.: E5100.01-401-44 Rendered to: INNOVATIONS MANUFACTURING, INC. Denver, Colorado PRODUCT TYPE: Transom Window SERIES/MODEL: IM too coin SPECIFICATION(S): AAMA/WDMA/CSA 101/I.S.2/A440-11, NAFS 2011 -North American Fenestration Standard/Specification for Windows, Doors, and Skylights Title SummaKy of Results AAMA WDMA CSA 101 I.S.2 A440-11 Class R-PG50 1829 x 309 72 x 12 -TR Design Pressure ±2400 Pa ±50.13 s Air Infiltration <0.1 L s/mz <0.01 cfm/ftz Water Penetration Resistance Test Pressure 440 Pa 9.19 pso This report contains in its entirety: Cover Page: 1 page Report Body: 5 pages Alteration Addendum: 1 page Location Air Seal: 1 page Drawing: 1 page Test Completion Date: 02/11/15 0��•41N P.' M Cp01/,�� Joi::•�10ENSF•.9� :� * No. 77418 ,t = •a STATE OF ' C PST •`:�<ORIOP:' _A; w.,ey.aera�a,m 2015.04.23 16:17:11-04'00' Reference must be made to Report No. E5100.01-401-44, dated 04/23/15 for complete test specimen description and detailed test results. 2250 Massaro Boulevard wwwarchtest.com . www.intertek.com/building p• 813.628.4300 Tampa, FL 33619 f. 717.764.4129 ®� Architectural Testing - — - -- � Test Report No.: E5100.01-401-44 Report Date: 04/23/15 Page 1"of 5 1.0 Report Issued To: Innovations Manufacturing, Inc. 4555 Grape Street Denver, Colorado 80216 2.0 Test Laboratory: Architectural Testing, Inc. an Intertek company ("Intertek-ATI") 2250 Massaro Boulevard Tampa, Florida 33619 813-628-4300 3.0 Project Summary: 3.1 Product Type: Transom Window 3.2 Series/Model: IM 3.3 Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The specimen tested successfully met the performance requirements for a Class R-PG50 1829 x 309 (72 x 12)-TR rating. 3.4 Test Dates: 02/10/15 - 62/11/15 3.5 Test Record Retention End Date: All test records for this report will be retained until February 11, 2019. 3.6 Test Location: Intertek-ATI test facility in Tampa, Florida. 3.7 Test Specimen Source: The test specimen(s) was provided by the client. Representative samples of the test specimen(s) will be retained by Intertek-ATI for a minimum of four years from the test completion date. 3.8 Drawing Reference: The test specimen drawings have been reviewed by Intertek-ATI and are representative of the test specimen(s) reported herein. Test specimen construction was verified by Intertek-ATI per the drawings located in Appendix C. Any deviations are documented herein or on the drawings. 3.9 List of Official Observers: Name Owen Bunker Wilferson Simbert Company Innovations Manufacturing, Inc. Intertek-ATI www.archtest.com . www.intertek.com/building ®� Architectural Testing 4.0 Test Specification(s): Test ReportNo.: E5100.01-401-44 Report Date: 04/23/15 Page 2 of 5 AAMA/WDMA/CSA 101/1.S.2/A440-11, NAFS 2011 - North American Fenestration Standard/Specification for Windows, Doors, and Skylights 5.0 Test Specimen Description: 5.1.Product Sizes: Overall Area: 0.6 In (6 ft2) Width IHeight millimeters inches millimeters inches Overall size 1 1829 72 305 12 5.2 Frame Construction: Frame Member Material I Description Head, sill and Aluminum Extruded jambs joineryType Detail Each corner was sealed with sealant and All corners Mitered and keyed secured with one inside aluminum corner key with epoxy, 5.3 Weatherstripping: No weatherstripping was utilized. 5.4 Glazing: No conclusions of any kind regarding the adequacy or inadequacy of the glass in anyglazed testspecimen(s) can be made. Glass Type Glazing Glazing Method Interior glazed against adhesive Monolithic 3 mm thick backed foam glazing tape and annealed glass secured with snap -in PVC glazing beads. Location Quantity Daylight Opening Glass Bite millimeters inches Transom daylight 1 1784 x 260 70-1/4 x 10-1/4 1/2" opening www.archtest.com . www.intertek.com/building Archl�l Testing 5.0 Test Specimen Description: (Continued) 5.5 Drainage:_ No drainage was utilized. 5.6 Hardware: No hardware was utilized. 5.7 Reinforcement: No reinforcement was utilized. 6.0 Installation: Test Report N E5100.01-401-44 Report Date: 04/23/15 Page 3 of 5 The specimen was installed into a 2x6 Southern Yellow Pine wood buck. The rough opening allowed for a 1/8" shim space. The exterior perimeter of the window was sealed with sealant. Location chor Description Anchor Location t2ng 3" from each corner and spaced 8" Head, sill and jamb roofing nails on center, through the nail fin and trim board into the wood buck 7.0 Test Results: The temperature during testing was 19°C(6717). The results are tabulated as follows: Title of Test Results Allowed Note Air Leakage, Infiltration per ASTM E 283 <0.1 L/s/mz 1.5 L/s/mz at 75 Pa 1.57 s <0.01 cfm ftz 0.3 cfm ftz max. 1 Water Penetration, per ASTM E 547 N/A N/A 2 Uniform Load Deflection,. per ASTM E 330 N/A NIA 2 Uniform Load Structural, - per ASTM E 330 N/A N A 2 Forced Entry Resistance, per ASTM F 588, Type: D -Grade: 10 Pass No entry www.archtest.com . www.intertek.com/building ®— Architectural Testing 7.0 Test Results: (Continued) Test ReportNo.: E5100.01-401-44 Report Date: 04/23/15 Page 4 of 5 Title of Test Results Allowed Note 0 tional Performance Water Penetration, per ASTM E 547 at 440 Pa .9.19 pso Pass . No leaka e 3 Uniform Load.Deflection, per ASTM E 330 Deflections taken at the head +2400 Pa (+50.13 psf) <0.3 mm (<0.01") -2400 Pa -50.13 s 0.3 mm 0.01" Report Only 4, 5, 6 Uniform Load Structural, per ASTM E 330 Permanent sets taken at the head +3600 Pa (+75.19 psf) 0.5 mm (0.02") 0.8 mm (0.03") max. -3600 Pa -75.19 s 0.5 mm 0.02" 0.8 mm 0.03" max. 4, 5, 6 Note 1: The tested specimen meets (or exceeds) the performance levels specified in AAMA/WDMA/CSA 101/LS.2/A440 for air leakage resistance. Note 2: The client opted to start at a pressure higher than the minimum required. Test results are reported under Optional Performance. Note 3: Without insectscreen. Note 4: The deflections reported are not limited by AAMA/WOMA/CSA 101/1.S2/A440 for this product designation. The deflection data is recorded in this report for special code compliance and information only. Note S. Loads were held for 10 seconds. Note 6: Tape and film were not used to seal against air leakage during structural testing. www.archtest.com . www.intertek.com/building Ak —® IAtcSi�l Testing— — - Test Report No.: E5100.01-401-44 Report Date: 04/23/15 Page 5 of 5 Intertek-ATI will service this report for the entire test record retention period. Test records such as detailed drawings, datasheets, representative samples of test specimens, or other pertinent project documentation, will be retained by Intertek-ATI for the entire test record retention period. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written approval of Intertek-ATI. For ARCHITECTURAL TESTING, Inc. D4t*&%mdbr.Dada)P.Bm D4b YBi9JWbr.JPMtDwWd Daniel P. Braun J.P. McDonald, P.E. Senior Vice President Director - Regional Operations VLM:vlm Attachments (pages): This report is complete only when all attachments listed are included. Appendix -A: Alteration Addendum (1) Appendix-B: Location of Air Seal (1) Appendix-C: Drawing(s) (1) This report produced from controlled document template ATI 00438, revised 06/27/14. www.archtest.com . www.intertek.com/building Test ReportNo.: E5100.01-401-44 Repo�te--W4/Z2j15 Appendix A Alteration Addendum Note: No alterations were required. www.archtest.com • www.intertek.com/building E510 ®— ^•- - — — Test ReportNo.: tUafte 04/22-44 — - n n tuTesting Report�te�4J22/15 Appendix B Location of Air Seal: The air seal between the test specimen and the test wall is detailed below. The seal is made of foam weatherstripping and is attached to the edge of the test specimen buck. The test specimen buck is placed against the test wall and clamped in place, compressing the weatherstripping and creating a seal. Test Air Seal (WeathwWppIno Test Spedmen Bic Test Spedmen www.archtest.com . www.intertek.com/building ^, T Test ReportNo.: E5100.01-401-44 —��Architectural re.noa—Reporflfte3 �4�22�15 Appendix C Drawing(s) www:archtest.com . www.intertek.com/building M AS TESTED INSTALLATION NOTES: 1. WINDOW.MUST BE INSTALLED INTO A SPF OR BETTER 2X WOOD MEMBER 3 2. WINDOW MUST BE INSTALLED USING 2" LONG, #8 ROOFING NAILS. ALL NAILS MUST BE SPACED A MAXIMUM OF 6" ON CENTER, THROUGH THE NAIL FIN .INTO THE 2X WOOD MEMBER. 3. ALL INSALLATION FASTENERS MUST BE LOCATED A MINIMUM OF 1/2" FROM THE EDGE OF THE NAIL FIN AND HAVE A MINIMUM EMBEDMENT OF 1-1/2".. I 1-1/2" MIN EMBEDMENT #8 x2" LONG 1/2" MIN 2X WOOC ROOFING NAILS BUCK MIN (SPF min) EDGE EDGE DISTANCE EDGE DISTANCE 1-1/2" MIN 1/8" SHIM EMBEDMENT SPACE, �I TRANSOM / WINDOW 1/8" SHIM #8x2"LONG _l SPACE ROOFING NAILS TRANSOM WINDOW SECTION A -A hEAD/SILL DETAILS 2X WOOD Busl�ingBetterTog6theG SECTION B-B compiles vAth se defogs. BUCK ,IAMB DETAILS Deviations ere noted. II (SPF min) Report#: E5100.01-44011--44 /gLDate: 04/ 13/201 Verified by: TUFF SHED ONel k. PO# THEBEDRETHEaANOTHE TITLE APwL- DESIGNAHED IN ROPEfttt TUFF SHED, INC. aPfl-TRA soM Customer. Drexm By. PK DRAWNG AREFC THESE INSTALLATION INSTRUCTIONS I OPAWINGTOBEF02F Storage Buildings&Garages DateCheclm!By. AND BUILT09EBFPNap INHOUSE 1777. HARTINGDETREET NT REV. LEVEL 01 not TUFF SHED, INC. Situ P AVER, COLORA O80210 x FOR MANUFA T WINDOWS AND BUILT TUFF SHED. 1777 S. HARRISON STREET Cata: tlBy, FNYOTHERUBEIB DENVE$COL3-TUFF 0210 MANUFACTURED BY $HEFT Data: INCFORBIDNBYTUER OF (..4.3-TUFF Bulltling Sire:.m..uwm..,ur.e"n. )� F�ENt8T EE�NG ENGINEER o[ rvneiaome, wvwuie p swunro" INNOVATIONS MFG,INC SHEET 10F�3 $tale: N.T.S. RECORD.