HomeMy WebLinkAboutPRODUCT CERTIFICATIONNOTICE OF PRODUCT CERTIFICATION
SCANNED
CERTIFICATION NO:
— DATE:
CERTIFICATION PROGRAM:
COMPANY:
CODE:
REVISION DATE:
BY
St. Lucie County
NI009198-R5
12/30/2007-
Structural
Maxim
M-1256-1
08/21/2017
To verify that the "Notice of Product Certification" is valid, please visit www.NAMICertification.com to assure that
the product is active and currently listed. This certification represents product conformity to the applicable
specification and that certification criteria has been satisfied. A NAMi approved certification label must be applied
to the product to claim certification status. Please review and advise NAND if any corrections are required to this
document.
COMPANY NAME AND ADDRESS
PRODUCT DESCRIPTION
Maxim Industries, Inc.
Series "Dade Self -Flashing"
1630 Terre Colony Court
Polycarbonate Glazed Aluminum Skylight
Dallas, Texas 75212
Configuration: O
Glazing: Exterior Dome-0.118" Hyzod Polycarbonate
w/8" rise/lnterior Dome-0.118" Hyzod Polycarbonate
w/4" rise
Overall: W46" DLO: W-37'
H-8'6" H-79"
SPECIFICATION
PRODUCT RATING
TAS 201/202/203-94
Design Pressure: +60/-60 psf
Large Missile Impact Rated
Product Tested By:
Report No:
Expiration Date:
Administrator's
Architectural Testing, Inc.
ATI-01-43381.01
December 31.2021
NATIONAL ACCREDITATION AND
MANAGEMENT INSTITUTE, INC.
4794 George Washington Memorial Highway
Hayes, VA 23072
Tel: (804) 684-5124
Fax: (804) 684-5122
Product Evaluation
61G20.3 F.A.C. I Report No. 2000, Rev. 2 1 Project No. 418-0102 1 3/2/18 1 Page 2 of 2
Material Certifications/Component Approvals:
• Polycarbonate Panel Dome Material: See current Miami -Dade Notice of Acceptance (NOA) for component
approval for the following approved material.
o Covestro LLC Makrolon Polycarbonate Panels NOA can be found here.
Limitations & Conditions of Use:
• This product has been evaluated for use inside the HVHZ (High Velocity Hurricane Zone)
• This product is Impact Resistance; therefore, a protective impact -rated device is not required.
• Refer to Product Installation Instructions noted above for.
o Maximum allowable wind loads at related maximum allowable size(s).
o Overall dimensions and material/grade of main product components, accessories, etc.
o Illustrated diagrams of the attachment of the product to the structure.
o Anchor type(s), size(s), substrate(s), embedment, edge distance, and spacing%locations.
• Site wind pressures shall be determined by a licensed professional engineer in accordance with the current edition
of the Florida Building Code and/orASCE 7-10 for components and cladding based on allowable stress design.
• Site conditions not covered in this product evaluation document are subject to additional engineering analysis by a
licensed professional engineer or registered architect as required by the authority having jurisdiction.
• Adequacy of the existing structural substrates as a main wind force resisting system capable of withstanding and
transferring applied product loads to the foundation Is the responsibility of the licensed professional engineer or
registered architect acting as the design professional of record for the project of installation.
Certificate of Independence per Product Approval
Rule 61G2O-3.009
PTC Product Design Group, LLC and RobertJ. Amoruso, P.E.
does not have, nor will acquire, any financial Interest in the
company manufacturing or distributing product(s) covered
by this Product Evaluation Report. PTC Product Design
Group, LLC and RobertJ. Amoruso, P.E. do not have, nor
will acquire any financial interest in any other entity
involved in the approval process or testing of the
product(s) covered by this Product Evaluation Report.
Digitally signed
by Robert J
Amoruso
Date:
2018.03.05
10:09:46-05'00'
Evaluated by:
Robert J. Amoruso, P.E.
Fl. PE License No. 49752
�ANW PTC Product Design Group, LLC I PO Box 520775 1 Longwood, FL 32752-0775
rEiL 321.690.1788 1 FBPE Certification of Authorization No. 25935