HomeMy WebLinkAboutNOAMl®�E
MIAMI.DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.eov/economy
James Hardie Building Product, Inc.
SCANNED
10901 Elm Avenue
BY
Fontana, CA 92337
St. Lucie County
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AID may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code,
including the High Velocity Hurricane Zone.
DESCRIPTION: "Hardie", "Cem" and "Prevail" Planks and Panels Fiber Cement Siding and Soffit
APPROVAL DOCUMENT: Drawing No. PNL, PLK & SOFF, titled "HardiePanel, CemPanel, Prevail
Panel; HardiePlank, CemPlank Prevail Lap Siding; HardieSoffit, CemSoffitPanel; Installation Details
Wood/Metal Stud Construction", sheets 1 through 12 of 12, dated 04/24/2013, prepared by the
manufacturer, signed and sealed by Ronald I.Ogawa, P.E., bearing the Miami -Dade County Product
Control renewal stamp with the Notice of Acceptance number and expiration date by the Miami -Dade
County Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LABELING: A permanent label with the manufacturer's name or logo, Plant City, Florida, and the
following statements: "ASTM C 1186 Type A compliant" and "Miami -Dade County Product Control
Approved" is to be located on each siding plank or panel and per FBC 1710.9.2 and 1710.9.3 on soffit
panels.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA # 15-0122.04 and consists of this page 1 and evidence page E-1, as well as
approval document mentioned above.
The submitted documentation was reviewed by Carlos M. Utrera, P.E.
NOA No. 17-0406.06
MIAMMADE Caurmr Expiration Date: May 1, 2022
Approval Date: May 4, 2017
�(y7 /2017 Page I
James Hardie Building Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
A. DRAWINGS "Submitted under NOA # 13-03IL07"
1. Drawing No. PNL, PLK & SOFF, titled "HardiePanel, CemPanel, Prevail Panel;
HardiePlank, CemPlank Prevail Lap Siding; HardieSoffit, CemSoffit Panel;
Installation Details Wood/Metal Stud Construction", sheets 1 through 12 of 12, dated
04/24/2013, prepared by the manufacturer, signed and sealed by Ronald I. Ogawa,
P.E.
B. TESTS "Submitted under NOA # 13-0311.07"
1. Test reports on 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
2) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of HardiePlank, HardieSoffit
and HardiePanel, prepared by Intertek Testing Services NA LTD, Test Report No.
100733361COQ-004, dated 08/24/2012, with revision 1 dated 04/25/2013, signed and
sealed by Rick Curkeet, P.E.
"Submitted under NOA # 02-0729.02"
Laboratory Report Test Date Signature
2. ATI-16423-1 PA 202 & 203 03/18/96 A. N. Reeves P.E.
3. ATI 16423-2 PA 202 & 203 03/18/96 A. N. Reeves P.E.
4. ATI 16423-3 PA 202 & 203 03/18/96 A. N. Reeves P.E.
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENTS "Submitted under NOA # 15-0122.04"
1. Statement letter of code conformance to the P edition (2014) FBC issued by Ronald
I. Ogawa & Associates, Inc., dated 10/26/2014, signed and sealed by Ronald I.
Ogawa, P.E.
AO tr7/-Zo17
Carlos M. Utrera, P.E.
Product Control Examiner
NOA No. 17-0406.06
Expiration Date: May 1, 2022
Approval Date: May 4, 2017
E-1
WAIL
PRODUCT RENEWED
as complying with the Florida
Building Code
NOA-No. 17-0406.06
12022
WALL LENG1
Stud Spacing at 16" O.C.
a.a__ , I i
0
Nai
3/8" Mihttnum Edge oistance is at 16" O.C. (typ.)
8IL.A Sheathing fastener, as described in
'—./— Note 1
Panel fastener, as described in
Note 2
HarliePanel, Cempanel,
Prevail Panel Siding
Water -resistive barrier per
Florida Balding Code Section
14042
5/8" thick / 5 ply APA rated
plywood sheathing fastened in
accordance with Florida Building
Code Section 2322.3
2" X 4" S-P-F Wood Studs
The wall and soSd frames are to, be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
SEE
DETAIL A
T518" ticki 6 ply APA rated
plywaod sheathing in
a=cdance v ilh Florida
Buiildiing Code Section
23223
Water-reestive
barrer per Florida
Bullding Code
Section 1404.2
2" X 4" S-P-F
Wood Sheds
HardiePamel.
iEC,L6_B Cempanel,
preyall Panel
Siding
PRQ-'LC'T DESC�tI-P_no�l.
Hardie Panel®, Cempanel®, &
Prevail® Panel Siding materials are
nonasbestos fiber -cement products
tested in accordance with ASTM
G1186 Grade 11, Type Aand meeting
the requirements ofthe Florida
Building Code.
,p�ptE)LDIMF,�ySJQ(!IS
Weith Length Thickness
4' 8,9,10' 5/18"
FS1GJI�R_E$SU&E _:TUJCi
Installation Design Pressure
Wood Studs -76 pal
Impact Resistant -
Planks installed over 5B" thick / 5 pry
APA rated plywood sheathing
hIF),KUMIMcr-4-1%-1 C IV, rJynF,�_N:.,.•z�o-lvc--•_"-- -____. .___ —..
• All installationshall be done in conformance with this Notice of Acceptance, the manufacturer's
installation recommendations, and the applicable sections of the Florida Building Code.
• Wood studs where Hardie Panel, Cempanel, Prevail Panel Siding VA be installed shall be
designed by an Engineer crArchitect per the Florida Building Code and the requirements of this
N.OA
• [Note 11 sW thick 15 ply APA rated plywood sheathing shall be attached to the studs In
accordance with Florida Building Code Section 2322.3.
• The Sidling panels shall be installed over 5/8" thick / 5 ply APA rated plywood sheathing supporter
by a minimum of 2X4" S-P-F wood studs spaced a maximum of 16" O.C.
• [Nate 21 The siding panel fastener shag be a 2" long, oi=' head diameter, 0.o92" shank
edges
diameter, corrosion resistant siding nail; the fasteners shall be spaced at 6" O.G. at p
and intermediate studs; the fasteners shall be driven through the 518" thick 15 ply APA rated
plywood sheathing into wood studs located at 16" O.C.
• Fasteners shall have a minimum edge distance of 3/8" and a minimum clearance of T from
comers.
HARDIEPANEL, CEMPANEL., PREVAIL PANEL
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA=37
A I I PNL-PLY,SOFF
Creator E. Gonzales scua 1f2"=1'-0" I Date; 412412013 Isnsar 1OF 12
REV
Fastener Spacing per Florld
Building Code.Section 2322.3 16,OOin.
'taemccRE ED Fastener Spacing per Florida
� gwlhthe8lorian Building Code Section 232 -3
AcmpWM No
Dme
-BY PmdudCmaoS - I -I I'I rirr'/III l
I 1
FROIHJCCBEVISED
PRODUCT RENEWED
mv+�driln.8s as complying with the Florida
�� pf% ilding Code Bu; : • N
_ � ��'rj]� NOA-Nb. 77-0405.06
Ex Iratron e05/0112022
p
9r 1 PmductC.enhdS By
Mleml- a duct Control I I _^ O��s F�O•"
Ni
F-96M NG
• NOMINAL 2" X 4" S-P-F WOOD STUDS 16" O.C. FASTENED
WITH 3-1W 16d COMMON NAILS (2 PER TOP AND
BOTTOM CONNECTION)
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEI&T 00
• NOMINAL 5/8" THICK/ 5 PLY APA RATED PLYWOOD
SHEATHING FASTENED IN ACCORDANCE WITH FLORIDA
BUILDNG CODE SECTION 2322.3
,�I,gDDTNG
• THE PANEL IS FASTENED WITH 2' LONG, 0.223' HEAD
DIAMETER, 0.092" SHANK DIAMETER, CORROSION
RESISTANT SIDING NAILS, PLACE NAILS 6" O.C. AT
PANEL EDGES AND INTERMEDIATE STUDS
1
Cladding
Framing
iC
Sheathing
15
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPANEL, CEMPANEL, PREVAIL PANEL
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc,
10901 Urn Avenue
Fontana, CA92337
Fax 909-427.0634 A PNL•PLKSOFF 1
Creator. E. Gonzales 'scale P� a 1'-0" pata:4/24lZ013 SHEET 2OF 12
1
WALL
1
AE,T6D A -
PRODUCT RENEWED
as complying with the Florida
Building Code
NOA-No. 17-0406.06
WALL LENGTH
Stud Spacing at 16" O.C.
a—__ 1 ,
STATE
I Nails at 6" O.C, (typ.)
3/8" Minimum Edce Distance
Sheathing fastener, as
described in Note 1.
Panel fastener, as described In
Note 2
HardiePanel® Siding
Water -resistive barrier per
Florida Building Code Section
1404.2
5/8" thick IS pry APA rated
plywood sheathing fastened
to metal studs as described
in Note 1.
209a, 3-5/8" X 1-5/8" Metal Cstud
The wall and sofRt frames are to be designed
by the Architect or Engineer of Record In
compliance with the Florida Building Code.
SEE
DETAILA
�— 618" tluok 13 ply APA rated
plywood sheathing fastened
to metal studs as described
in Note 1
PROCLUCT DU6.CBlP_7TP9
HardlePanel®, Cempanel®, & Ptevail0
Panel Siding materials are nonesbestos
fiber -cement products tested in
accordance with ASTM Of 188 Grade it,
Type A and meeting the requirements of
the Florida Building Code.
=
ggn]4o�M�FtSLONs
Water -resistive
Width Length Thickness
barrierper Florida
4' 8,9,10' 5/16"
yt
Building Code
r
Section 14042
JMSJGN_PJ3ER%UUjJ 6TJNG
(
Installation Design Pressure
20ga, 3518" X 1-618"
Metal Studs -104 psf
Metal Cstud
HardlePanel,
Impact Reslstant-
sS9cTaOf11:144
Cempansl,
Panel installed over 518" thick / 5 ply
Prevail Panel
APA rated plywood sheathing
Siding
]fAj�Dtj=�1NEL CEMPANFJ„�PgESA_{L_P1NE,�.SID1[�LGIYySTf,L1,A�'IO�ETAILS
• " All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's
installation recommendations, and the applicable sections of the Florida Building Code.
• Metal studs where HardiePanel, .Cempsnel, Prevail Panel Siding will be Installed shall be
designed by an Engineer or Architect per the Florida Building Code and the requirements of this
N.O.A.
• [Note 11 5/8" thick 16 ply APA rated plywood sheathing shall be attached to metal studs at Was
at panel edges and all Intermediate supports using a No.8-18, 0.315" head diameter 1-1W long
bugie head screw
The siding panels shall be installed over 518"thick /5 ply APA rated plywood sheathing
supported by a minimum 20ga, Nominal 3-5/8" X 1S18" Metal C-studs spaced a maximum of 16"
D.C.
• [Note 2] The siding panel fastener shall be a minimum No. 8-18, 0,315" head diameter X 1-5/8'
long` ribbed bugle head screw ('cr screw shall have at least 3 full threads penetratingmetal
framing); the fasteners shall be spaced at 6" O.C. at panel edges and intermediate studs; the
fasteners shall be driven through the 5/8" thick 15 ply APA rated plywood sheathing into metal
studs located at 16" D.C.
• Fasteners shalt have a minimum edge distance of 3/8" and a minimum clearance o12" from
comers.
HARDIEPANEL, CEMPANR, PREVAIL PANEL
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA 92337
PNL-PLKSOFF
Creator,. I -Gonzales IsakE' 1fL"=i'A" 1 Date:4124/2013 IsHEET 3OF 12
. M
PRODUCT RENEWED
as complying with the Florida
Building Code
NOA-No. 17-0406.06
exatratlon Bate 05/01 /2022
' T
6.00in.
PAODUCTHEVISM
m oom0yinivftthoF5Mi'.de
tt
BY
minaw PMdxmtGMiW
II
I•I
II
T I I
&001n. I
I
I' I
II
I' II
I
VRWucr REVLSFD '
® ..,rein* vnth the F10"
IOW
pdW of
ProOud
FRAMQ�G
NOMINAL 20 GAUGE 3.6/8" X 1-5/e" STEEL STUDS 16" O.C.
FASTENED WITH 518, WAFER HEAD SCREWS (2 PER TOP
AND BOTTOM CONNECTION)
+ THE WALLAND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SyEAl�'F lN_G
• NOMINAL 51VITHICK/ 5PLY APARATED PLYWOOD
SHEATHING TO METAL STUDS AT W OC AT PANEL
EDGES AND ALL INTERMEDIATE SUPPORTS USING A
NO.8-16, 0.319' HEAD DIAMETER X 1-1W LONG BUGLE
HEAD SCREW
CLADDING
• THE PANEL IS FASTENED WITH NO.8-18, 0.315" HEAD
DIAMETER X 1-518' LONG CORROSION RESISTANT
RIBBED BUGLE HEAD SCREWS (SCREW SHALL HAVE AT
LEAST 3 FULLTHREADS PENETRATING THE METAL
FRAMING), PLACE SCREWS 6" O.C. AT PANEL EDGES
AND INTERMEDIATE STUDS
• I
II
11
' I'I
' II
Cladding
Framing
Sheathing
�.I
OGA
se*'
I �
I•I �` 121
Q.
STATE OF
I
�•I --FCOR1�?:
S�ONA1-�
�dr
FOR MErALAND WOOD STUDS PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPANEL, CEMPANEL, PREVAIL PANEL
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10901 Elm Avenue
Fontana, CA92337
Fax 909427-0834 A PNL-PLK-SOFF
Creator. E. Gonzales ISCALC 1"= V-0" Date:4124/2013 suer 40F 12
1
MnLL-A
"r
PRODUCT RENEWED
as complying with the Florida
Building Code
Non -No. 17-0406.06
Sheathing fastener, as
described in Note 1
Siding fastener, as
described in Note 2
HardiePlank,
Cemplank, Prevail
Lap Siding
Water -resistive barrier
par Florida Building
Code Section 14042
LIX 5/8" thick / 5 ply APA rated
plywood sheathing fastened
--.in accordancewith Florida
Building Code Section
2322.3
Expiration te05/01/2022 2"X 4" S-P-F Wood Studs
The wall and soffit frames are to be designed
BY.1 by the Architect or Engineer of Record In
ive Product Control cmmnliancewith the Florida Building Code.
36E.
�EfA1LA
p�OG)�I DESCR{PT1011
HardlePlank®, Cemplank®, &
Prevail® Plank Lap Siding materials
5/5/80 thick 16 APA are nonasbestos fiber cement
/I`
ply
products tested in accordance with
d plywood
ASTM C1186 Grade 11, Type A and
athing in
meeting the requirements of the
ordance with
Florida Building Code.
Florida Building Code
tion 2322.3 N L D EN 1 -_
P.9� LMI. QNS
Water-resis&e Width Length Thickness
barrier parFlorida 59-1/2• 12' SM6"
J�hBuilding Code
Section 14042 9 �GN PRE- -,F �.NR
2^X40S-P-F Installatlon Design Pressure
Wood Studs Wood studs -92 psf
Lap Sitling Impact Resistant -
Planks Installed over 5/3" thick / 5 ply
1-114" iaa X 5/16" APA rated plywood sheathing
flick siartetslrip
tigR.4tEP_I /SNK CF del-ANIS ME-A-EtJ-AP—SIDI.NGJ1JSTA JIST 0XQlUAa1-S
• Ali installation shall be done in oonform8ncewlth this Notice of Acceptance, the manufacturees
Installation recommendations, and the applicable sections of the Florida Building Code.
• Wood studs where HardlePlank, Cemplank, Prevail Lap Siding will be installed shall be designed by an
Engineer or Architect per the Florida Building Code and the requirements of this N.O.A.
• [Note 115/8' thick 15 ply APA rated plywood sheathing shall be attached to the studs in accordance
with Florida Building Code Section 2322.3.
• Planks shall be applied horizontally commencing from the bottom course of the well with 1-1l4" wide
laps at the top of the plank such that the exposure area of each plant( is 58-1/4"'vertically.
• [Note 2] The siding fastener shall be a 2-1/Z long, 0.223" head diameter, 0.092" shank diameter,
corrosion -resistant siding nail; The siding is fastened S 8-114" O.C. vertically and16d sheathing, fasteners
fasteners are driven into wood studs through 5/8 thick ! 5 ply APA rated plywood
are placed in the overlapping area approximately 314' from the bottom edge off the overlapping plank.
• Vertical joints shalt be placed over studs.
• The planks shall be Installed over 5/8" thick 15 ply APA rated plywood sheathing supported by a
minimum of 21X4" S-P-F wood studs spaced a maximum of 16" O.C.
• Fasteners shall have a minimum edge distance of 3!6".
Creator. E. Gonzales
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Inc.
' 10901 Elm Avenue
Fontana, CA 92337
A I I PNL-PLK-SOFF
112" =1'�0" I - Date: 4124/2013 IsueET 5 OF 12
Fastener Sparing per Florida
Building Cade Section 2322.3
PRODUCT RENEWED
as complying with the Florida
Building Code
_ _ __NOA-No. 17-0406.06
0.75n Expiration Dqtt,051011112022
By
Mlaini-D'adia Product Control
FRAMING
• NOMINAL 2" X 4" S-P-F WOOD STUDS 16" O.C. FASTENED
WITH 3-1/2' 16d COMMON NAILS (2 PER TOP AND
BOTTOM CONNECTION)
• THE WALL AND SOFFIT FRAMES ARE TO SE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHP,ItTHING
• NOMINAL 5/6"THICK /5 PLY APA RATED PLYWOOD
SHEATHING FASTENED IN ACCORDANCE WITH FLORIDA
BUILDING CODE SECTION 23223
silLA M
• PLANKS.OVERLAP 1-i/4"
• THE EXPOSURE IS 56.1/4"
• THE PLANKS ARE FACE NAILED WITH 2-1/2 LONG, 0.223"
HEAD DIAMETER, 0.092" SHANK DIAMETER, CORROSION.
RESISTANT SIDING NAILS, -PLACED 3W UP FROM THE
BOTTOM EDGE OF THE PLANKAT EACH STUD LOCATION
Fastener Spacing per Florida
Building Code Section 2322.3
i.
I
P@mucr REYISM .I
a « I . 'V f1� Plaids
ftfift
Cladding
Framing
Sheathing
121
STATE OF
sj0NAt E 01 V
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND G17AVITY LOAD A
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS WOOD STUD CONSTRUCTION
James Hardie Building Products, Ina.
10901 film Avenue
Fontana, CA 92337
Fax909,427-0634 j A I IPNL-PLKSOFF
Creator, E. Gonzales SCALE 1" =1'-0" Date: 424=13 sxEE7 6 OF 12
1
Stud Spacing at 16" O.C.
WAE1 LENGTH
--------,_
I l
'•'
NALL
(�
' i •.
mcoop-, gvab k6 nw1da
'Cotit
1w '.
EIGHT
I
•i�`
ii
O >
���
:�••
r PwdWizCcawl I
jj :I.
---------- i__-._-''i_.__—____1•,
_ I�
•' 'Q
13
Alnl• A
PRODUCT RENEWED
as complying with the Florida
Building Code
NOA-No. 17-0406.06
Expiratlon
By
S/4- minimum tcage uistance Naas ar na" u.u, (typ,) �� -, •��� p,4W41
Sheathing fastener,
described in Note 1
SEE
P&ODUCT bESO-ELTV-Phl
ETAIL A
HardiePlank®, Cemplank®, and
—518" thick! 9 pIyAPA
Prevail® Plank Lap Siding materials
ra ed plywood
are nonasbestos fibar-cement
sheathing fastened
products tested In accordance with
to metal studs as
ASTM C1186 Grade II, Type A and
described in Nate 1
meeting the requirements of the
Florida Building Code.
Watervresistive,
border per Florida
PIANI< DIMENSJONS
Z.
Building Code
Width Length Thickness
Section 14042
59-1/2" 12' ails"
20ga, MW X 1.5/6" DEjPN PR.E9$UBF RA'0 1�G
Metal C sGltl Installation Design Pressure
HardiePlank, Metal Studs -92 psf
Cemplank, Prevall
Lap 81ding Impact Resistant -
1-1/4' tell X 5/16" Planks Installed over 518" thick15 ply
thick starter strip APA rated plywood sheathing
• All installation shall be done in conformance with this Notice of Acceptance, the manufacturer's Installation
as recommendations and the a licable,sections of the Florida Buiidln Code
Siding fastener, as
described in Note 2
HardiePlank,
Cemplank,
Prevail Lap Siding
Water -resistive
barrier per Florida
Building Code
Section 1404.2
5/8"thick / 5 ply APA rated
plywood sheathing fastened to
metal studs as described in
Note 1
209a, 35/8"X 1-5/8" Metal Cstud
The wall and soffitframes are to be designed
by the Architect or Engineer of Record in
compliance with the Florida Building Code.
PP g
• Metal studs where HardiePlank, Cemplank, Prevail Lap Siding will be installed shall be designed by an
Englneer or Architect per the Florida Building Code and the requirements of this N.OA
• [Note 115/8" thick / 5 ply APA rated plywood sheathing shall be attached to metal studs at 6"00 at panel
edges and all intermediate suppags using a No.8-18, 0.316' head diameterx 1.1/4" long bugle head screw
Planks shall be applied horizontally commencing from the bottom course of the wall with 1-14 wide laps at
the top of the plank such that the exposure area of each plank is s 8-1/4" vertically.
• [Note 2) The siding fastener shall be a minimum No. 8-18, 0.315" head diameter X 2-1/4" long` bugle head
screw over metal studs Coor screw shall have at least 3 full threads penetrating metal framing); The siding Is
fastened 4 8.1/4" O.C. vertically and 16" O.C. horizontally; fasteners are driven Into metal studs through 518"
thick 15 pry APA rated plywood sheathing,' fasteners are placed in the overlapping area approximately 3/4"
from the bottom edge of the overlapping plank.
• verticaljoints shall be placed over studs.
• The planks shall be Installed over 518" thick /5 ply APA rated plywood sheathing supported by a minimum
20ga, Nominal 3-5/8" X 13/8" Metal Cstuds spaced a maximum of 16" O.C.
• Fasteners shall have a minimum Edge distance of 3/8".
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc,
10901 Elm Avenue
Fontana, CA 92337
PNL-PLK SOFF
'Creator, E. Gonzales ISCALE 1/2"=V-W j Date:412412013 jSHEEr 70F12
fi.00in. fa-- �.-16in.
6.001n. I' .
PRODUCT RENEWED I _S _I as complying with the Florida
Building Code
-NOA-No. 17-0406.06
0.751n.� Expiration D teDS/01/2022 -
By
Miami - a" Product control '
Wan(i.UesrPros
58251n.
e- Mal I"- .
• NOMINAL20 GAUGE 3.5/6"X 1-5/8" STEEL STUDS 16"
O.C. FASTENED WITH 51T LONG RIBBED BUGLE HEAD
SCREWS (2 PER TOP AND BOTTOM CONNECTION)
• THE WALLANO SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
SHEA G
• NOMINAL S/8"THICK/5 PLY APA RATED PLYWOOD
SHEATHING TO METAL STUDS AT6 OCAT.PANEL
EDGESAND ALL INTERMEDIATE SUPPORTS USING A
NO.8-18, 0.316" HEAD DIAMETER X 1-1/4' LONG BUGLE
HEAD SCREW
CLADD�IG
• PLANKS OVERLAP 1-114'
• THE EXPOSURE IS:; 8-1/4n
• THE PLANKS ARE FASTENED WITH NO, 8-18, 0.315"
HEAD DIAMETER X 2-1W LONG CORROSION -
RESISTANT RIBBED BUGLE HEAD SCREWS (SCREW
SHALL HAVE AT LEAST 3 FULL THREADS -
PENETRATING THE METAL FRAMING), PLACED ShV UP
FROM THE BOTTOM EDGE OF THE PLANK AT EACH
STUD LOCATION
/ •I
8EYL5Ep •I
Cladding
Framing
Sheathing
aft Cot I� - `
"e 0. 121
a o I ATE OF
FOR METAL AND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIEPLANK, CEMPLANK, PREVAIL LAP SIDING
INSTALLATION DETAILS MECALSTUD CONSTRUCTION
James Hardie Building Products,.Inc.
10901 Elm Avenue
Fontana, CA 92337
Fax909,427-0634 A PNL-PLK-SOFF 1
Creator. E. Gonzales sC4L'c 1" = T-0' Oate:4242D13 571eE7 8 OF 72
WALL
WALLLENGTH
Stud Spacing at 16" O.C.
Rom_ I I
tODUCT RENEWED
complying with the Florida
Ilding Code
A -No, 17-0406.06
Expiration
SEE
DETA(LA
Nails at G' O.C. (typ.) PAt9DUCf REVISED
318" Minlmum Edge Distance °" COf°UlYh*Wilhd" FU"
,fit CO&,dar
AFTALO BY
PmAM Comd"
Q&OOUCs115A R-ILQN
HardieSoffitO A Cemsofflt® materials
are nonasbestos flber-cement products
tested In accordance with ASTM C1186
Grade 11,1ypeA and meeting the
requirements of the Florida Building
Code.
3.518"X1-518" SOEET_DJMEN5lOYj;.
C•srud Width Length Thickness
4 8' Y.."
'diesotft DESIGN gSSI1RE RATWG
'msoffit Installation Design Pressure
Metal Studs 55 p f
ird
o'°flii L 06 _
Fuoma 9EVLWD
ma complyim wile fiwFlarkin ``51 S •'••.
Huadieg Cado No. 121 Anxptmoeo No 1.3�C3!l•Cj : I
Mwmr9 ` 9p', STA OF
cP•oaeuCDotroaORIDP,�;�
HA13AAEs0�EiT�QENLsQEELL29NEL INSTAi �9L4ClD CAJ1& '�-r��NAL EN riillr-rt�tt
" Ali Installation shall be done in conformance with this Notice ofAccepianFb!g1cyMaahufadurer's
installation recommendations, and the applicable sections of the Florida Building Code.
Soffit fastener, as • Metal studs where HardieSoffit, Cemsoftit will be installed shall be designed by an Engineer or
described in Note 1 Architect per the Florida Building Code and the requirements of this N.O-k
• The soffit shall be installed over minimum 20ga, Nominal $.618" X 1-5/8",Metal C-studs spaced
— HardieSoffd, Cemsofft a maximum of 16" O.G.
[Note 11 The soffit fastener shall be a minimum No. 8.18, 0.315" head diameter X 1-1/4" tong'
ribbed bugle head screw ('or screw shall have at least 3 full threads penetrating metal
framing);the fasteners shall be spaced at 6" O.C. at panel edges and Intermediate studs; the
fasteners shall be driven into metal studs totaled at 18" O.C.
Fasteners shalt have a minimum edge distance of 318" and a minimum clearance of 2" from
comers.
HARDIESOFFIT, CEMSOFFIT PANEL
INSTALLATION DETAILS METALSTUD CONSTRUCTION
James Hardie Building Products, Inc.
20ga, 3-5/8" 1-51W Metal C-stud
10901 Elm Avenue
The wall and soffit frames are to be
s
Fontana, CA 92337
designed by the Architect or Engineer
Phone:202358-MOD
size
F=MND
DNbND
Rear
of Record in compliance with the
Fax 909-427-0634
A
PNL-PLKSOFF
I
1
Florida Building Code.
I
Creator. E..Gonzales
SCALE IX" 11- I
Date; 4/E4/2013
SHEET 11 of 12
PRODUCT RENEWED
as Complying with the Florida
Building Code
NOA-No. 17-0406.06
Explration t)�O5/01/2022
Ia . �,y�
MODUCr REVISED
9dWi BCodr .r -.-, .w
FRAIJQNG
• NOMINAL20 GAUGE M18" X 1.5/8" STEEL STUDS 1W O.C.
FASTENED WITH 5/8' WAFER HEAD SCREWS (2 PER TOP
AND BOTTOM CONNECTION
• THE WALL AND SOFFIT FRAMES ARE TO BE DESIGNED
BY THE ARCHITECT OR ENGINEER OF RECORD IN
COMPLIANCE WITH THE FLORIDA BUILDING CODE
CJ ADDING
THE SOFFIT IS FASTENED WITH NO, 8-18, 0.315" HEAD
DIAMETERX 1-1/4' LONG CORROSION RESISTANT RIBBED
BUGLE HEAD SCREWS (SCREW SHALL HAVE AT LEAST 3
FULL THREADS PENETRATING THE METAL FRAMING), PLACE
SCREWS 6" O.C. AT PANEL EDGES AND INTERMEDIATE
STUDS
FOR METALAND WOOD STUDS, PROVISIONS FOR DIAPHRAGM ACTION AND GRAVITY LOAD ARE
NOT PART OF THIS APPROVAL (MUST PROVIDE ALTERNATE PROVISIONS FOR THESE LOADS)
HARDIESOFFIT, CEMSOFFIT PANEL
INSTALLATION DETAILS METAL STUD CONSTRUCTION
James Hardie Building Products, Inc.
10961 Elm Avenue
Fontana, CA 92337
Fax909427-0634 A PNL-PLIf-SOFF 1
Creator..E.Gonzales SCALE 1"=1'-0" Date:4/24M1013 ISKEET 120Et2
C