HomeMy WebLinkAboutNOAMIAMIM E MIAMI-DADE COUNTY, FLORIDA
METRO -DARE FLAGLER BUILDING
BUILDING CODE COMPLIANCE OFFICE (BCCO) SCANNED 140 WEST FLAGLER STREET, SUITE 1603
PRODUCT CONTROL DIVISION BY MIAM,I,. FLORIDA33130.1563
(NOA)
St. Lucie County (305) 375-2901 FAX (305) 372-6339
NOTICE OF ACCEPTANCE rnvw.miamidade.gov/buildinacode
Best Rolling Doors, Inc.
9780 NW 791h Avenue
Hialeah Gardens, FL 33016
SCOPE:
IQ
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed by Miami -Dade County Product Control Division
and accepted by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas
where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Division (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA
reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control
Division that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone.
DESCRIPTION: Model S10-6565 Steel Roll -up Door
APPROVAL DOCUMENT: Drawing No. 6565_2009_02, titled "Model S 10-6565', sheets 1 through 3 of
3, dated 04/06/09, prepared by Best Rolling Door, Inc, signed and sealed by Joseph H. Dixon, Jr, P.E.,
bearing the Miami -Dade County Product Control approval stamp with the Notice of Acceptance number and
approval date by the Miami -Dade County Product Control Division.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and
following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been
no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change
in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of
any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to
comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA consists of this page 1 and evidence page E-1, as well as approval document mentioned above.
The submitted documentation was reviewed by Carlos M. Utrera, P.E.
NOA No. 09-1103.05
Expiration Date: January 27, 2015
Approval Date: January 27, 2010
J I7/10 Page 1
Best Rolling Doors, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
A. DRAWINGS
1. Drawing No. 6565_2009_02, titled "Model S 10-6565", sheets 1 through 3 of 3, dated
04/06/09, prepared by Best Rolling Door, Inc, signed and sealed by Joseph H. Dixon,
Jr., P.E.
B. TESTS
1. Test reports on 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS.203-94
4) Tensile Test per ASTM A370-05,
Along with marked -up drawings and installation diagram of Model S 10-6565 Steel
Garage Doors, prepared by Fenestration Testing Laboratory, hic., Test Report No.
FTL # 5589, dated 01/13/09, signed and sealed by Michael R. Wenzel, P.E.
C. CALCULATIONS
1. Calculations for attachment of "C" channel guide to steel or concrete jamb, dated
07/23/09, prepared, signed and sealed by Joseph H. Dixon, Jr., P.E.
D. QUALITY ASSURANCE
1. Miami Dade Building Code Compliance Office (BCCO)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 07-1107.08, issued to Dyplast Products, LLC, for their
Expanded Polystyrene Block Type Insulation, approved on 02/28/08 and expiring on
01/11/12.
F. STATEMENTS
1. Statement letter of code conformance, dated 10/16109, signed and sealed by Joseph H.
Dixon, Jr., P.E.
2. Statement letter of no financial interest, dated 10/16/09, signed and sealed by Joseph
H. Dixon, Jr., P.E.
Carlo M. Utrera, P.E.
Product Control Examiner
NOA No. 09-1103.05
Expiration Date: January 27, 2015
Approval Date: January 27, 2010
E -1
MI®=ME
BUILDING CODE COMPLIANCE OFFICE (BCCO)
PRODUCT CONTROL DIVISION
NOTICE OF ACCEPTANCE
Daybar Industries Limited
50 West Drive,
Brampton, Ontario, Canada L6T 2J4
MIAMI-DADE COUNTY, FLORIDA
METRO-DADE FLAGLER BUILDING
140 WEST FLAGLER STREET, SUITE 1603
MIAMI, FLORIDA 33130-1563
(305) 375-2901 FAX (305) 375-2903
www.miamidade.gov/buildingcode
IZ.I Zoizo IV
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.
The documentation submitted has been reviewed by Miami -Dade County Product Control Division and accepted
by the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by
the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Division (hi Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right
to revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code,
including the High Velocity Hurricane Zone.
DESCRIPTION: Series "LS-18" Outswing Commercial Steel (Galvanneal or Stainless) Doors w/ 16 ga
Frames & w/wo Panic Exit Device-LM Impact
APPROVAL DOCUMENT: Drawing No "09-030", titled "Double & Single LS18 Outswing Commercial
Galvanneal or Stainless Steel Doors w/ Series"AS"16 ga Steel frames", sheets 1 through 3, 3A and 4 thru 19 of 19
prepared by Tilteco Inc, dated MAR 17, 2009, signed and sealed by Walter A. Tillit Jr. , P. E., bearing the Miami -
Dade County Product Control Renewal stamp with the Notice of Acceptance number and expiration date by the
Miami -Dade County Product Control Division.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
Limitations: 1. Glazed vision liter are limited per sheet 8.
2. Min edge distance required for ITW 3/16" Tapcon (item #22) is 2-5/8" and for Power 5/16-18
caulk -in anchor is 3-3/4".
LABELING: Each unit shall bear a pennancnt label with the manufacturer's name or logo, city, state and
following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no
change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any
product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply
with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded- by the words Miami -Dade County, Florida, and followed by
the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall
be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors
and shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA # 09-0323.21(06-0117.01) consists of this page 1 and evidences page E-1, as well as
approval document mentioned above.
The submitted documentation was reviewed by Ishaq I. Chanda, P.E.
MIAMI•DADECOUNrY
,.=
NOA No 10-0217.05
Expiration Date: April 07, 2015
Approval Date: May 05, 2010
Page 1
Daybar Industries Limited
' NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
A. DRAWINGS (transferred from file # 09-0323.21)
1. Manufacturer's parts and sections drawings (transferred from file # 05-0620,06)
2. Drawing No "09-030", titled "Double & Single LS18 Outswing Commercial Galvanneal or
Stainless Steel Doors w/ Series"AS"16 ga Steel frames", sheets 1 through 3, 3A and 4 thru 19
of 19 prepared by Tilteco Inc, dated MAR 17, 2009, signed and sealed by Walter A. Tillit --
Jr., P. E.
B. TESTS (transferred from file # 09-0323.21)
1. Test reports on 1) Air Infiltration Test, per FBC, TAS 202-94 (except sp# 7 louver)
2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94
3) Water Resistant Test, per FBC, TAS 202-94 (except sp# 7 louver)
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94
Along with marked -up drawings and installation diagram of outswing steel door, prepared by
Hurricane Testing Laboratory, LLC, Test Report No. HTL-0279-0719-03 dated 07-16 thru
08-18-2003 for specimen 1, 2, 3, 7 & 7 EMB, signed and sealed by Vinu J. Abraham, P.E.
Note: The above test report has been revised with addendum letters dated Dec 16, 2004 and a
revised marked -up drawing issued on 12-15-2004 by Hurricane Testing Lab, signed and
sealed by Vinu J. Abraham, P.E.
C. CALCULATIONS: (transferred from file # 09-0323.21)
1. Anchor Verification Calculations, complying w/ FBC-2007, dated 03/17/09, prepared,
signed and sealed by Walter A. Tillit Jr., P. E.
D. QUALITY ASSURANCE
1. Miami Dade Building Code Compliance Office (BCCO).
E. MATERIAL CERTIFICATIONS (transferred from file # 05-0620.06)
1. Tensile Test report No. Job# 0279-0719-03, dated March 02, 2004, issued by Q C
Metallurgical, Inc, per ASTMS-8, signed & sealed by Frank E. Grate, P.E.
2. Notice of Acceptance No. 07-1107.08 issued to Dyplast Product, LLC (Former Apache
Products Co.) for "EPS-Expanded Polystyrene Insulation", expiring on 01/11/12.
3. Notice of Acceptance No. 08-0305.02, issued to SABIC Innovative Plastic (Former
G.E. Plastic) for "Lexan Sheet Product", expiring on 07/17/2013.
F. STATEMENTS (transferred from file # 09-0323.21)
1. Statement letter of compliance to FBC-2007 and "No financial interest, both dated
April 29, 2009, signed by Walter A. Tillit Jr., P. E.
2. Facsimile correspondence dtd Nov. 14, 2005 from DAYBAR, requesting substitution
of Stainless Steel in lieu of Galvanneal Steel & BCCO response dated 11/23/05.
3. Statement letter of compliance issued by Hurricane Testing Laboratory LLC:, as part
of above referenced test report.
G. OTHER
1. This NOA renews NOA # 09-0323.21(06-0117.01), expiring April 07, 2010.
2. Material properties data sheet of AISI 304 Stainless Steel.
2. Manufacturer/Distributor agreement between Daybar Industries Ltd. & Daybar
Southeast Service Centre, signed by respective officials (original in le #04-0818.02).
shaq I. Chanda, P.E.
Product Control Examiner
NOA No 10-0217.05
Expiration Date: April 07, 2015
Approval Date: May 05, 2010
E-1