Loading...
HomeMy WebLinkAboutOWNER MANUALS•( ��-;����t� i1 Sr. Lucie County, permitting Opeff,< SCANNED ,1� Il'1L�17.� BYSt. Lucie Cow Important Read this document before operating / installing this product For additional product manuals and operation / installation procedures, please visit www.AquaCal.com I— —— — — — — — — — 1 MODEL SERIAL NUfvi6ER LTM0883 REV 2a Table ®f Contents Section I - Contaeting AquaCa➢ Aut®PiRct, Inc. Section (2 - �af¢tj _ ,• 1 Section 3 - Operation 3.1 Energizing Heat Pump ......-•-• ....................................•-- ............-•---...... 2 3.2 Display Door...-•-----------------------•---.....-•-•-----........---................-•--......------.............. 2 3.3 Display Lock......................••----••-•---......--..................------.................................... 2 3.4 Display Panel............................................................•-•-•----•---.................-------••.... 2 3A.a Buttons........--•-•-••----••--•--•..................•------•--.....................-•-•--------............... 3 3.4.b Indicator Lights...........................................•--................-•-•--------...........----..... 3 3.4.c Display................•--•------------....................................--..........•-•--•-----.......--.... 3 3.5 User Level Factory Defaults.............................•--......•---..........-•--•-•----•.........-•----..... 4 3.6 Setting Operating Mode-----•................•-•------.....--------.............-•----...............--.......... 5 3.7 Selecting Celsius or Fahrenheit................................................................................. 5 3.8 Setting Thermostats..................•---------------............---....-•-•--•-----------........--•---.......... 5 3.9 User Lock Option (Enable)....................•-••---------•-----•--.............-•---------•---...-•---........ 6 3.10 User Lock Option (Disable)--•..............................•-------..................--•---....--. 7 3.11 User Lock Option (Entering Pass Code).................................................................... 7 3.12 Operating Heat Pump (With an External Controller)..................................................... 8 Section 4 - Maintenance 4.1 Monitoring Conditions.......--•............................•-•--•----------.................---.....------...... 8 4.1.a Water Chemistry ...--•-----•................................•--------------.........----------....------..... 8 4. Lb Water Flow Rates-----••---.....--••-•-------------------•---........----------.............•----........... 9 4.1.c Adjusting Water Flow Using AT (Delta-T)...........................................................10 4.Ld Irrigation and Storm Run-Off............................................................................ I I 4.1.e Clearances ..............................----...-•-------.............................11 4.2 Cleaning Equipment-----•-----•--••-•-•--•-•-•-•-------------------•---.........------------------------•--------12 4.3 Planned Maintenance-------------------------•----...................------------------.....--------......---...13 4.4 Winterizing---........-•...........................••----........................------.........--•-----......-----.14 Section 5 - Troubleshooting 5.1 Fault Codes............................•-•---•------...........................-----...........----......------....16 5.2Issues and Resolutions.........--•.............••--•---------------..............------........------......--....18 Section 6 - Appendix 6.1 Identifying Model Specifications..............................................................................21. 6.2 Initial Heating Recommendations.............................................................................22 6.3 Initial Cooling Recommendations .............................................................................22 6.4 Available Accessories---------------------------------------------•---.........--------.......-----••-----...--..22 ISECT90H 9' - 'CONTACTING AQUA(CAL AUTOPILOT, MC. For further assistance, please contact the installing dealer or contact AquaCal Autopilot, Inc. fora service. partner in your area. To better assist you, please have the heat pump model and serial number aiailable. See "Identifying Model Specifications" on aaee 21. Wcehsite www.AquaCal.com Request SerwiseOungine -•n,wv,.AquaC-,. 4::, ee,;:<s li nt-3t;nir•-:; roicer Phone (1) 727-823-5642 -- Hours _ 8-5 pm, Eastern M-F mc-noN ?_ - SAFIEry For personal safety, and to avoid damage to equipment, follow all safety instructions displayed on the equipment and within this manual. Repair and service of heat pump must be performed by an authorized service center. • Warranties may be voided if the equipment has been improperly installed, maintained or serviced. • If service is deemed necessary, please contact the installing dealer. Or contact AquaCal` for a service partner in your area. See "Contacting AquaCal AutoPilot, Inc." on page I. SSAFIETFSllrGNALS Throughout this document, safety signals have been placed where particular attention is required A WARNING - signals relate to personal safety. i CAUTION -signals promote avoiding damage to the equipment. When installing and using your heat pump basic safety precautions must always be followed, including the following: G-\ WARNING - Failure to heed the following may result in injury or death. > Installation and repairs must be performed by a qualified technician. * The heat pump contains refrigerant under pressure. Repairs to the refrigerant circuit must not be attempted by untrained and / or unqualified individuals. Service must be performed only by qualified HVAC tedilicians. Recover refrigerant before opening the system. The heat pump utilizes high voltage and rotating equipment. Use caution when servicing. • Electrical installation and service should be performed by a Licensed Electrician only. • Improper water chemistry can present a serious health hazard. To avoid possible hazards, maintain pool / spa water per standards detailed in this document. • Prolonged immersion in water warmer than normal body temperature may cause a condition known as Hyperthermia. The symptoms of Hyperthermia include unawareness of impending hazard, failure to perceive heat, failure to recognize the need to exit the spa, and unconsciousness. The use of alcohol, drugs, er medication can greatly increase the risk of fatal Hyperthermia. In addition, persons having an adverse medical history, or pregnant women, should consult a physician before using a hot tub or spa. Children and the extreme elderly should be supervised by a responsible adult. • Prolonged immersion in water colder than normal body temperature may cause a condition known as Hypothermia. The symptoms of Hypothermia include shivering (although as hypothermia worsens. shivering stops), clumsiness or lack of coordination, slurred speech or mumbling, confusion and poor decision -making, drowsiness or low energy, lack of concern about personal welfare, progressive loss of consciousness, weak pulse and slow or shallow breathing. In addition, persons having an adverse medical history, or pregnant women, should consult a physician before immersing in a cold body of water. Children and the extreme elderly should be supervised by a responsible adult. Page - 1 CAUTION - Failure to heed the following may result in equipment damage. " Maintain proper water chemistry in order to avoid damage to pump, filter, pool shell, etc. o Water flow exceeding maximum flow rate requires a bypass. Damage due to excessive water flow will void warranty. SAVE THESE INSTRUCTIONS 3 - OPERATION 3.9 (Energizing Heaa Pump Turn power on at external fuse box or breaker disconnect. o Controller performs a lamp test. " The display reads 608. " Controller then displays as normal. See "Display" on page 3. 3.2 Display Door The display panel is located in a door compartment on the front of the heat pump. This compartment is designed to protect the display against harsh weather. It can also be padlocked for extra security. " Press the bottom of the panel to open the display panel door. o To close, push the display panel up. Then press the bottom of the panel in until a clicking noise is heard. 3.3 Display Lock The heat pump has a display lock to protect against inadvertent setting changes. To activate display and controls, slide finger across the controls as shown from left to right. o The code VnL will briefly appear, then the set temperature or mode will display. o This is different than a user -lock which requires a pass code. See "User Lock Option (Enable)" on page 6. 3.4 Display Panel 77 J The following information outlines the operation for a standard installation. o Control Buttons will operate differently for custom installations; such as a heat pump connected to an external controller. See "Operating Heat Pump (With an External Controller)" on page 8. bane! Page - 2 3A.a Buttons Buttons Description Display lock Sliding your finger across the buttons from left to right will temporarily disable the display lock. Pool / Spa Select either the pool or the spa thermostat. Up Arrow Used to increase temperature set point and navigate though menu options. Down Arrow Used to decrease temperature set point and navigate though menu options. Mode Select heat pump's operating mode. 3.4.b Indicator Lights Indicators Description P®o➢ The Heat Pump is referencing the pool thermostat. Spa The Heat Pump is referencing the spa thermostat. Indicates the unit is heating the water. Heating Please note - the compressor must be operating before this light will illuminate. Indicates the unit is cooling the water. Cooping Please note - the compressor must be operating before this light will illuminate. Water Temp Indicates current water temperature. Desired Tempe Indicates temperature set point is displayed. This is displayed when "UP" or "DOWN" is selected. 3.4.c Display Display Description -8s The heat pump is on and displaying the current water temperature. In this example 75' F is displayed. FL ® No water flow is detected. The filter pump is off or heat pump is not receiving correct water flow. The heat pump has been turned off via the mode selector OFF button or the temperature set point has been lowered below 45° F. The control program is initializing. This displays only as ®®® power is applied to the heat pump. The program version number will then be displayed. Page - 3 Display Description CF I Select water temperature format (in either Celsius or Fahrenheit). ULC Enable heat pump lockout feature. ELC Select passcode to lock the keyboard. This is a Service Entry Point (not intended for use by the owner). The LOC code permits service personnel to enter a LUC factory passcode to access adjustable calibration and site dependent setup parameters. Service adjustments are available to authorized installation and service personnel, only. �3 User Level Factory Defaults— -- - — -- Certain programming options have been preset at the factory. These options can be overwritten for site - specific conditions. CAUTION - Failure to heed the following may result in equipment damage. o Unauthorized adjustments in the Installer Menu (beyond the L BE menu) may void heat pump's warranty. Table 1 - Factory Defaults CODE9DESCEtI[PTION IlDVALUEFAUB RANGE E VALUE OFF Heat Pump is deactivated. Set to heat water iiEfl to point set on thermostat. Set to cool water COO to point set on thermostat. Set to maintain a flCH water temperature set on the thermostat. Celsius / EF 1 Fahrenheit 1 0 = Celsius 1= Fahrenheit Selection ELC Enter Lock Code 0 0 - 99 111E User Lock Code 0 0 = "User Lock Disabled" 1 = "User Lock Enabled" Page - 4 3.6 Setting Operating Made Heat Mode C®ol Mode Beating / Cooling modes only available on select equipment_ Confirm heat pump features before setting a mode. 3.7 Selectina Celsius or Fat reruheit Hold "UP" and "DOWN" until [F i displays. 3.8 Setting Thermostaa Select "POOL" or "SPA" Press "UP or "DOWN" button to select. "0" - Celsius "I" -Fahrenheit Press "UP" or "DOWN" to the desired temperature. Automatic Heat / Cool Mode o The heating indicator will illuminate when heating the water. o The cooling indicator will illuminate when cooling the water. Deactivate Heat Page - 5 3.9 User Lack Option (Enable) The user -lock feature allows the heat pump display panel to be 'locked". This can prevent unauthorized temperature adjustments in commercial applications. Do not confuse a user -lock with the display lock. See "Display Lock" on page 2_ " 1 f GE is briefly displayed, followed by a "0", theheat pump is already locked. " If the user -lock code has been misplaced, please contact AquaCal- Customer Service for further assistance. Hold "UP" and "DOWN" until IF I displays. Press "POOL / SPA" button until ULC is displayed. Press "POOL / SPA" button until ELC is displayed. Press "Up" button till "1" is displayed to enable. Press "UP or "DOWN" button to change or add a numerical password Press "POOL / SPA" button to lock in the password. Page - 6 3.90 User Lock Op¢ioo (MsWe) Use "UP" button to enter existing password. Press "DOWN" button until "0" is displayed. Press "_Pool / Spa" button to unlock. Hold "UP" and "DOWN buttons until EF I is displayed. Press "POOL / SPA" button until ULE is displayed 3.21 User Lock Op -don- Q Enferung Pas Code) If E®C is briefly displayed when attempting to change a heat pump's settings followed by a "0",the beat pump is in a user -lock mode. A numerical passcode is required to proceed. Press "UP" or "DOWN" arrow to enter user lock code. Press TOOL/ SPA" button to unlock. NOTE- * After three seconds of inactivity, the heat pump's display lock will activate. See "Display Lock" on page 2. If the user -lock code has been misplaced, please contact AquaCal' Customer Service for further assistance. Page - 7 �.fl2 Operating Bleat Pump (With. an. lExternal Controller) Controller aisith an internal thermostat control Activating heat Pump 1. Set the desired temperature at the external controller. 2. Use the external controller to select either the "Pool" or "Spa" to heat. (Deactivating Heat Pump Set the external controller to "OFF". Please note - If equipped, the heat pump's cooling function will he disabled when using this type of controller. If the cooling function is needed, the heat pump must be temporarily re -programed for local control. Check with controller installer if heat pump needs to be re -programmed. Controller with 2 positions - ("Pool" and "Spa" - no internal thermostat control) Activating Heat Pump 1. Set the desired temperatures on the heat pump thermostats. See "Setting Thermostats" on page 5. 2. Use the external controller to select either the "Pool" or "Spa" to heat. o Rapid movement between thermostats without a "rest" between each change can cause a missed signal by the heat pump. Deactivating Heat Pump Go to the heat pump and set the mode to "OFF". See "Setting Operating Mode" on page 5. Please note - If equipped, the heat pump's cooling function will be disabled when using this type of controller. If the cooling function is needed, the heat pump must be temporarily re -programed for local control. Check with controller installer if heat pump needs to be re -programmed. Controller with 3 positions - ("II$igh", "Low", and "Oft" - no internal thermostat control): Activating Heat Pump 1. Set the desired temperatures on the heat pump thermostats. See "Setting Thermostats" on page 5. 2. Use the external controller to select either "High" or "Low" to heat. • When changing between thermostats, select "Off' first. Then select desired thermostat. o Rapid movement between thermostats without a "rest" between each change can cause a missed signal by the heat pump. Deactivating Heat Pump o Set the external controller to "OFF". SECTION 4 - MAINTENANCE 4.11®Ionitoring Cont9itions _._- -.------- 4.1.a Water Chemistry Check water chemistry regularly and maintain within recommended levels. Standards for commercial applications vary in different areas. Follow all local applicable codes. ` CAUTION - Failure to heed the following may result in equipment damage. o Do not allow water to flow through heat pump when refinishing or acid washing a pool. Either use an installed bypass to route water away from heat pump or deactivate filter pump. e To avoid damage to equipment, monitor and maintain chemistry within recommended levels. Page - 8 C'MJSTRY LEVEL CHART (RESIDENTIIAL) CHEMICAL POOLS SPAS (Chlorine 1.0 — 3.0 ppm 3.0 — 5.0 ppm Bromine 2.0 — 6.0 ppm 2.0 — 6.0 ppm Cyanuric Acid 30 - 50 ppm 30.- 50 ppm PH 7.4-7.6ppm 7.4-7.6ppm Total A➢ka➢inity 80 —120 ppm 80 —120 ppm calcium 200 — 400 Hardness ppm 150 — 250 ppm EDibssoRved 0 —1,500 ppm 1,500 ppm above start-up total dissolved solids in spas ° Salt from a chlorine generator is not included in Total Dissolved Solids. 4.1.➢n Water Flow Rates Maintain water flow rates as indicated. Please note, these specifications relate to the heat pump caly. Code - specified whole system turnover rates must be satisfied. 9`..CAUTION -Failure to heed the following may result in equipment damage. Water flow exceeding maximum flow rate may damage heat exchanger; such damage will not be covered under the equipment warranty MODEL BEAT EXCHANGER TYPE FLOWRATES MINIMUM MA%IIMIJH SQ12OR Titanium ThermoLink® 30 GPM 70 GPM SQ125 Titanium ThermoLink® 30 GPM 70 GPM SQ145 Titanium ThermoLink® 30 GPM 70 GPM SQ166R Titanium ThermoLink® 30 GPM 70 GPM SQ225 Titanium TbermoLinV 30 GPM 70 GPM T035 Titanium Tube -in -Tube 20 GPM 45 GPM T055 Titanium Tube -in -Tube 20 GPM 45 GPM T075 Titanium Tube -in -Tube 20 GPM 45 GPM T090 Titanium ThermoLink® 30 GPM 70 GPM T115 Titanium ThermoLink® 30 GPM 70 GPM T135 Titanium ThermoLink® 30 GPM 70 GPM Page - 9 If water flow through the heat pump is reduced, performance will suffer and internal safety devices may deactivate the heat pump with error codes UP and HP5, or (if equipped) an L P and L Ps. o Operate water filtration devices per manufacturer's specifications. Dirty filters can cause reduced water flow to the heat pump. An increase of 7-10 psi higher than the clean filter pressure typically reduces flow rates. This requires the filter to be cleaned or back -washed o Keep baskets free of debris. Similar to a dirty filter, large volumes of debris in the pump and skimmer baskets can reduce water flow. Check for improper valve settings. A partially closed valve after the filter, or a full -open bypass around the heat pump, will cause insufficient water flow through the heat pump. The maximum static (or operating pressure) is 50 pounds -per -square -inch (PSI). These specifications relate to the heat pump only. Code -specified whole system turnover rates must be satisfied. 4.1.e Adjusting Water Flow Using AT (Delta-T) The Delta-T is the temperature difference between the water temperatures entering and leaving the heat pump. The equipment can be fine-tuned for maximum performance by balancing water flow rates to maintain an ideal AT. o Installed Temperature / Pressure probes and ports are required to perform the following procedures. o This adjustment procedure is to be completed with the unit in HER mode only; REM and r00 discharge temperatures are not shown. PLEASE NOTIE - Temperature / Pressure ports are required for all commercial applications. They are strongly recommended (but not required) for residential installations. 1. Adjust heat pump thermostat to its lowest setting while in HER mode. 2. Deactivate the water filtration pump. 3. Adjust valves to a halfway open position leading to the heat pump. 4. Adjust valves to a fully open position leading away from the beat pump. 5. Activate the pool water filtration pump. 6. Slowly turn the thermostat up until the heat pump activates. o After a four -minute delay, the heat pump compressor will start. 7. With the heat pump running, confirm water filtration pump is operating properly with adequate flow and no short cycling. If needed, clean filters leading to the heat Temperature / Pressure Port (Shown with Probe) C sr PUMP. 8. Wait for water and refrigerant pressure to stabilize (approximately 5 minutes). 9. Adjust valves in the following order: A. Adjust valve leading away from the heat pump to correct temperatures measured with a temperature pressure probe. B. Allow pressure to stabilize. Then check temperature again. Re -adjust valve leading away from the heat pump as needed. 10. Mark valves at these positions for future reference. Temperature differences are based on pool temperatures of 720 (+ or — 3° F). For water temperatures outside this range, contact AquaCar Technical Support. Page -10 MODEL TEMPERATURE PERATUR;E SQ 120R 30 to 7017 SQ 125 30 to 7° F SQ 145 30 to 7° F SQ ] 66R 30 to 8° F -SQ225 4° to 9° F T035 10 to 4° F T055 20 to 5° F T075 30 to 7° F T090 30 to 6° F T115 30 to 70 F T135 40 to 8° F Table 2 - Temperature Chart 4.1.dl Irrigation and Storm Run -Oft' • Irrigation water may damage heat pump components. Have irrigation water directed away from the heat pump. • The heat pump will withstand normal rainfall. Do not allow a roof slope to direct rainwater onto the heat pump. Have a gutter installed on the roof edge to direct this water away from the heat pump. Or install the hat pump in another location. 4.1.e Clearances • Proper air circulation is required for the heat pump to operate efficiently. Avoid placing objects new or on top of the heat pump. This includes shrubbery and lawn furniture. These objects will also hinder maintenance access. • Avoid storing chemical containers near the heat pump. The chemicals can cause equipment damage. Overhead Clearance Overhangvft gutter / -4 I 1 � OVERHEAD Rain run-off and 5 feet It 52 cm] sprinklersshoutd be directed aivay from heater Page - 11 .2 Cleaning ]Equipment Cleaning and polishing your heat pump regularly can protect its appearance and longevity. More frequent servicing may be required for heat pumps located in sandy or coastal areas where sand and salt spray can become detrimental factors to equipment. AWARNING - Failure to heed the following may result in injury or death. e Possible electric shock hazard - Deactivate power to all electrical devices on the pad when washing heat pump. Do not restore electrical power until equipment is completely dry. `> CAUTION - Failure to heed the following may result in equipment damage. o Do not use a pressure cleaner to wash heat pump. Damage to heat pump components may result. If using a hose - end spray nozzle adjust spray pattern to low strength only. a Do not spray water directly into the interior of the heat pump; damage to components may result. e Do not use chemicals on the display panel. Page -12 Cleaning 1. Wash outside cabinet using a low-pressure water hose. A high-pressure water stream will cause damage to the aluminum fins of the heat pump. This damage is not covered under product warranty. 2. While the heat pump is still wet, use an approved cleaning agent to clean the exterior of the heat lump. Do not 3. 4. 5. use chemicals on the display panel. Use a detergent -dampened cloth to wipe the heat pump's exterior cabinet. Flush all exterior with fresh water using a low-pressure water hose. Dry the exterior cabinet using a soft cloth being careful not to damage evaporator fins. APPROVED CLEANING AGIENTS°- Fantastic® Formula 409e Cascade® All Power Plain Detergent (3% Solution) Table 3 - Cleaning Agents (Polishing 1. Polish the heat pump's cabinet panels using an approved polishing agent and following the manufacturer's instructions. Do not use chemicals on the display panel. 2. Rinse the heat pump panels with fresh water, wipe, and buff panels using a dry soft cloth. 3. Allow heat pump interior and surrounding equipment to "air-dry" for several hours prior to restoring electrical power. APPROVED PO LIISIEII NG AGENTS' Simonize Wax Glo-Coate Armor Alle Protectant Table 4 - Polishing Agents ' The trademarks used in approved cleaning and polishing agents are property of their owners and are not related to AquaCal . 4.3 PVanned kaintenance An annual inspection and maintenance program is strongly recommended starting no longer than one year after installation of the heat pump. In coastal areas a bi-annual inspection is recommended. See recommended inspection checklist. AquaCal° can perform this service in limited areas. Contact Customer Support for more information. A WARNING - Failure to heed the following may result in injury or death. Annual inspection and service must be performed by a qualified heat pump specialist in order to prevent physical injury or damage to equipment. Page - 13 RECOMMENDED IINEPECTION CRECKILIST o Check Air Temperature Change through Evaporator • Check and Clean Condensate Drains m Check Capacitor Value o Check Compressor Amperage Draw o Check Electrical Connections o Check Flow / Pressure Switch o Check Operating Controls and Temperature Sensors o Check Water Chemistry • Check Proper Voltage to Unit o Check Refrigerant Levels • Check Relay Contacts o Check Water Flow • Check filter pump Amperage Draw o Check Water Temperature Change through Heat Exchanger • Clean Evaporator's Coil o Clean Heat Pump's Cabinet 4.4 Wlnterizing J A WARNING - Failure to heed the following may result in injury or death. o Deactivate all electrical power to heat pump before performing hard freeze procedures. CAUTION - Failure to heed the following may result in equipment damage. • Failure to winterize heat pump may result in serious equipment damage. Freeze damage is not covered under the heat pump warranty. • While the plumbing connections are in the winterized condition (not fully tightened), it is imperative the pool and spa water not be circulated through the heat pump. Loss of water through loose plumbing connections may result in damage to circulation pump, pool and spa structures, and other equipment. ]Light )Freeze Conditions There are two freeze conditions requiring heat pump attention. A light freeze is when the ambient air temperature falls below 32 degrees Fahrenheit for less than 8 hours. Typically during light freeze conditions circulating (moving) water will not freeze. Override time clocks and allow filtration system to run continuously during light freeze conditions. Hard Freeze Conditions A hard freeze is when the ambient air temperature falls below 32 degrees Fahrenheit for more than 8 hours_ In areas where this condition is prevalent and sustained, the heat pump MUST be winterized for hard freeze conditions. Follow the correct procedure depending on the type of heat exchanger found in the heat pump. Rdentify Exchanger: I. Deactivate all electrical power to heat pump. 2. Deactivate filter pump. 3. Remove front access panel. 4. Identify heat pump exchanger from illustrations in this section. Then follow procedure for that heat pump's exchanger. Page - 14 Titanium Thnermol,ink" Exchanger (with Internal Drain) I. Disconnect the plumbing to the heat pump at connection unions (removal is counter- clockwise). 2. Remove internal drain plug. 3. Allow water to drain completely from the heat pump. Expect to see a lot of water drain out at first, and then a small amount to continue to drain out over a long period. 4. After heat pump is frilly drained, re -connect internal drain plug and reinstall front access panel. 5. Partially.reconnect.plumbing connection unions. 6. Winterizing is complete. 7. When ready to use heat pump again, hand -tighten connection unions. Reconnect electrical power, and set the operating mode on the heat pump. Activate filter pump. Titanium T hermolLlnlc® ]Exchanger (with no ]Drain) I. Reinstall front access panel. 2. Disconnect the plumbing to the heat pump at connection unions (removal is counter- clockwise). 3. Allow water to drain completely from the heat pump. Expect to see a lot of water drain out at first, and then a small amount to continue to drain out over a long period. 4. After heat pump is fully drained, reinstall front access panel. 5. Partially reconnect plumbing connection unions. 6. Winterizing is complete. 7. When ready to use heat pump again, hand -tighten connection unions. Reconnect electrical power, and set the operating mode on the heat pump. Activate filter pump. Titanium T u be-in-Tubc Exchanger 1. Disconnect the plumbing to the heat pump at connection unions (removal is counter- clockwise). 2. Allow water to drain completely from the heat pump. Expect to see a lot of water drain out at first, and then a small amount to continue to drain out over a long period. I Place an air hose into the pool inlet of the heat pump; wrap a clean rag around the hose to form a temporary seal. 4. Push all water from the water circuit using compressed air no stronger than 50 psig. The residual water should be forced out of the pool outlet. Allow compressed air to blow into S. 6. 7. S. the heat pump inlet for at least 15-20 seconds after the water stops coming out. Repeat process on the outlet side of the heat pump. Partially reconnect plumbing connection unions. Winterizing is complete. Internal Drain f y6. ro No-IDrain Y Titanium Tube-in- Ilahe i When ready to use heat pump again, hand -tighten connection unions. Reconnect electrical power, and set the operating mode on the heat pump. Activate filter pump. Page - 15 ISIE(CTION S = TROUBLESHOOTING I P IFan9t. Codes A fault code indicates a specific issue or condition that will require action before the equipment can resume operating. Please perform the following troubleshooting. If, the issue reoccurs, please contact the installing dealer. Or contact AquaCar for a service partner in your area. See "Contacting AquaCal AutoPilot, Inc." on page 1. A WARNING - Failure to heed the following may result in injury or death. o Repairs must not be attempted by untrained or unqualified individuals. o The heat pump contains refrigerant under high pressure. Repairs to the refrigerant circuit must not be attempted by untrained or unqualified individuals. Service must be performed only by qualified HVAC technicians. Recover refrigerant before opening the system. i °'• CAUTION - Failure to heed the following may result in equipment damage. o Service by unauthorized personnel will void the heat pump warranty. FLD Indicator ISSUE Low or no water detected. RESOLUTION 1. Confirm the filter pump is on. 2. If a multiple -speed filter pump is being used, run at a higher speed to determine if the error persists. Do not exceed maximum flow rate for your model. 3. Confirm water is not being diverted away from the heat pump. • See "Water Flow Rates" on page 9. • See "Adjusting Water Flow Using AT (Delta-T)" on page 10. [Er Indicator ISSUE This can indicate a loose or damaged communication cable. RESOLUTION A qualified technician should check the cable from control board to display assembly for a loose connection or visible damage. C5E IIndicaitor ISSUE This is a control system error. RESOLUTION Deactivate then reactivate power to reset controls. dPC or dP0 Indicator ISSUE Shorted or open defrost sensor. RESOLUTION A qualified technician should replace the defrost sensor. Page - 16 PE or PG Indicator ISSUE Shorted or open water sensor. RESOLUTION A qualified technician should replace the water sensor. MF1 Indicator ISSUE The refrigerant system's high-pressure switch is showing as open. RESOLUTION If the heat pump is a reversing unit, place it in HEFT mode and perform the following troubleshotting. Determine if an insufficient amount of water is being supplied to the equipment. 1. Confirm the filter pump is on. 2. If a multiple -speed filter pump is being used, run filter pump at a higher speed. Do not exceed musimum flow rate for the model. 3. Confirm water is not being diverted away from the heat pump. See "Water Flow Rates" on page 9. See "Adjusting Water Flow Using AT (Delta-T)" on page 10. MPS Indicator ISSUE The heat pump has locked due to five HP (high-pressure) faults during one call for heating or cooling. RESOLUTION ION 1. Deactivate then reactivate power to the heat pump to clear error. 2. Troubleshoot the high-pressure issue causing the error. See " HP Indicator" on page 17. LP IIndicator ISSUE The refrigerant system's low-pressure switch is showing as open. RESOLUTION If the heat pump is a reversing unit, place it in HER mode and perform the following troubleshooting. I. Check for proper fan operation. If fan is not operating, contact AquaCalb Technical Support. 2. Check for obstructed air flow around the heat pump. See "Clearances" on page 11. 3. Check for dirty or blocked evaporator coil. See "Cleaning Equipment" on page 12. 4. Check for signs of ice buildup on the coil. LPS Indicator ISSUE The heat pump has locked due to five L P (low-pressure) faults during one call for heating or cooling. RESOLUTION 1. Deactivate then reactivate power to the heat pump to clear error. 2. Troubleshoot the low-pressure issue causing the error. See "LP Indicator" on page 17. Page - 17 DR Indicator ISSUE Incoming water temperature exceeded 110' F and the unit is locked with an Ilk over temperature alarm. The heat pump will not operate until incoming water temperature drops to 100* F or lower. RESOLUTION 1. Determine if another heat source (gas heater, solar heater, etc.) is heating water being sent directly to the heat pump with the OEn indicator. This situation will need to be corrected before continuing. 2. Rule out an incorrect reading from the water temperature sensor. Verify existing water temperature with an accurate thermometer. If heat pump's sensor is inaccurate, the water temperature sensor may require replacement. 5.2 Issues and Resolutions A WARNING - Failure to heed the following may result in injury or death. a Repairs must not be attempted by untrained or unqualified individuals. o The heat pump contains refrigerant under pressure. Repairs to the refrigerant circuit must not be attempted by untrained or unqualified individuals. Service must be performed only by qualified HVAC technicians. Recover refrigerant before opening the system. i 9'•, CAUTION - Failure to heed the following may result in equipment damage. Service by unauthorized personnel will void the factory warranty. Please perform the following troubleshooting. For further assistance, please contact the installing dealer. Or contact AquaCar for a service partner in your area. See "Contacting AquaCal Autopilot, Inc." on page 1. ➢Disp➢ay Panel Not Responding 1. If the heat pump is controlled be an external controller, confirm the external controller settings. See "Operating Heat Pump (With an External Controller)" on page 8: 2. If the issue is still occurring, contact the installer or manufacturer of the external control device. Heat Pumps Not Running 1. Confirm equipment is receiving power. Is the heat pump display illuminated? o If not, confirm the main breaker (located at the power supply panel) and the disconnect switch (located near the heat pump) are both turned on. o If the display still does not illuminate, it is recommended that the heat pump installer or electrician confirms heat pump is receiving power. 2. Confirm correct mode is selected. See "Setting Operating Mode" on page 5. 3. Confirm thermostat is set correctly. See "Setting Thermostats" on page 5. o If heating the water, the thermostat should be set above the current water temperature. o If cooling the water, the thermostat should be set below the current water temperature. 4. If an error code is displayed, diagnose and correct the cause of the code. See "Fault Codes" on page 16. 5. If the heat pump is using an external controller, the heat pump may not be set correctly to accept the controller's signal. See "Operating Heat Pump (With an External Controller)" on page 8. Heat Pumps Tripping ]Breaker 1. Have an electrician confirm breakers are in good condition and properly sized for the heat pump. 2. Multiple heat pumps installed at the same site may benefit from special automatic sequencing controllers to avoid excessive power drops at start-up. See "Automatic Sequencing Controller" on page 22. 3. If a fault occurs immediately when the compressor starts, a qualified technician should evaluate the system. Page - 18 Heat Pump Won't Shutt Off PLEASE ArOTE When heat pump is set to "®FF" the display will show either the water temperature orFLO. l . Confirm the heat pump has reached the desired temperature set on the thermostat. The heat pump will continue to run until the set temperature is reached. 2. If the heat pump is using an external controller, it may not be set correctly. See "Operating Heat Pump (With an External Controller)" on page 8. Heat Pump Is Running, Not Heating 1. If the heat pump is using an external controller, confirm it is set correctly. • See "Operating Heat Pump (With an External Controller)" on page S. • If the heat pump is still not running correctly with this device, contact the installer of the alernal controller device or the device's manufacturer for further assistance. 2. Confirm heat pump mode is set to HER operating mode. 3. Confirm thermostat is set to the desired water temperature. 4. Confirm valves are correctly positioned to heat the correct body of water (either the pool or the spa). If heating a spa that overflows into a pool, confirm the spa is isolated when being heated (not flowing into the pool). 5. Confirm heat pump is transferring heat into the water. Measure the temperature of air discharge coming out of heat pomp fan. If discharge air is between 8° to 100 colder than the outside ambient air (entering air), then the heat pump is moving heat ireo the water. 6. If an error code is displayed, diagnose and correct cause of code. See "Fault Codes" on page 16. 7. Confirm that filter pump has a sufficient run-time. The heat pump will not run (or heat the water)without water flow. Heat Pump equipment will generally be set to run 24 hours a day in commercial appliradons.See "Initial Heating Recommendations" on page 22. 8. If heating a spa, deactivate air blower or venturi (if equipped) to allow for quicker heating times. For pools, deactivate water features, such as slides, waterfalls, or fountains to allow water to retain heat. Useof a liquid pool blanket product, such as an Aqua BlanketTu, can also compensate for excessive heat loss. See "Liquid Blankets" on page 23. Heat Pump Fs Running, Not lCoolling (Reversing Models) 1. If the heat pump is using an external controller, confirm the heat pump is programmed properly to allow for cooling. See "Operating Heat Pump (With an External Controller)" on page S. 2. Confirm the heat pump mode is set to COB operating mode. 3. Confirm the thermostat is set below the current water temperature. 4. Confirm valves are correctly positioned to cool the correct body of water (either the pool or the spa). If cooling a spa that overflows into a pool, confirm the spa is isolated when being cooled (not flowin, into the pool). 5. If an error code is displayed, determine and correct the condition causing the code. See "Fault Codes" on page 16. 6. Confirm heat pump is transferring heat out of the water. Measure the temperature of air discharge coming out of heat pump fan. If discharge air is between 8° to 100 warmer than outside ambient air (not coming out of heat pump), then the heat pump is moving heat out of the water. 7. Confirm that filter pump has a sufficient run-time. The heat pump will not run (or cool the water) without water flow. Heat Pump equipment will generally be set to run 24 hours a day in commercial appliations.See "Initial Cooling Recommendations" on page 22. Page - 19 Water Coming From Heat Pump The water may be normal condensation produced as a by-product of the heat pump's refrigeration process. The heat pump can produce 8 to 10 gallons of condensation per day depending on the humidity of the ambient air. Determine if the water is condensation or a possible leak. 1. If using chlorine or bromine as a pool / spa sanitizer, use a test strip in the water at heat pump to determine if sanitizer is present. If sanitizer is present, a leak may exist. 2. Deactivate heat pump, leaving the filter pump on. After several hours, determine if water is still coming from the heat pump. Page - 20 D I�E�7fII�1Y en' APPENDIX �.fl Ila9e�Q➢ffryu�g 1�1f®a➢e0 �pteeB>r�art6®cans 1. Find Data Plate -The data plate is usually posted on the DataPlateExampleside Or the equipment or the inside of the heat pump's access plate. 2. Find the model number on the data plate. The first letters and numbers indicate the model type. 3. The complete model number identifies the equipment's specifications. pYlloOlel SE MiDer }1INRUA1 DIdCURn`.GTJf:"� YlSaYUE u:A =. ==?11IC=: V%, O a O S1F:U_1U_I W,E DaW?UE=M W_-RSSgJl O ?NWDU.. T= Oil'. a_;la=VT:C -IC �l Nu;l= O AQUA CAL INO i IIIBARCODEIIC l: FACTO P.}•gEayILE I0IBAR CODEIII (MODEL NUMBER N01lfNCLATURE Bland Designation I I ATHROUGHZ I I I I I I AAA IRTHOUG ROUHZZ GH2 Unit Designation M vo.ynauu r C = ctprouicked A = 160:208-230 D =Demo Unit B = 3.60.208-230 H =High Pressure Cupratdckel D = 3.50380415 L =Tube -in -tube E=3;60:3S0=i20 M=packaging for Mexico G = 3*0A60 N=No Options H = L50.200-220 P = Thant-O-Link II (5M for 2016) N = Nil R=1hemto-0-Link II (3;4 and 5;8) T =Thermo-O-Link ll Features C = Chill Only X = None H = Heat Only Co!or Designation R = Heat and Cool S = Split Chiller A = Black outside cabinet.; l4Trite inside ntinet T=Split Heater B=Black W =147tite C=Creme Controls D=Dir T =Taupe A = Analog Refrigerant S = R410A T=R407C UPDATED E = R22 07;142016 . a Page - 21 6.2 llnitia➢.Heating Recommendations _ The following recommendations will reduce the amount of time required to heat a pool. If unsure of equipment heating capability, review equipment data p➢ate. See "Identifying Model Specifications" on page 21. 1. Confirm heat pump mode has been set to HER. 2. Set thermostat to desired water temperature. 3. Temporarily override the filter pump's time -clock for continuous operation. o This will allow the Heat Pump the time required to heat the water at start-up. o After the water has reached the desired temperature, the time -clock can be reset to normal operating time -frames. 15.3 Initial �ooleng IIBecommeudations The following recommendations will reduce the amount of time required to cool a pool or cold plunge application. llff unsure of equipment cooling capability, review equipment data plate. See "Identifying Model Specifications" on page 21. 1. Confirm heat pump mode has been set to [00. 2. Set thermostat to desired water temperature. 3. Temporarily override the filter pump's time -clock for continuous operation. o This will allow the Heat Pump the time required to cool the water at start-up. " After the water has reached the desired temperature, the time -clock can be reset to normal operating - time-frames.- 1b.4 AvailalDle Accessories -- -_' 5 lb Bypass Valve Kit (Kit ST1f0135) When high flow rates are outside recommended tolerances, please use this kit or an alternative bypass valve system. o This kit can be used to control excessive water flow through the heat pump. It provides automatic flow adjustments for most applications. Automatic Sequencing Controller o An Automatic Sequencing Controller (ASC) provides easy control of all units from one lead unit and prevents the simultaneous start-up of multiple heat pumps. o Site voltage drop is minimized and utilities are not subjected to large in -rush demands of electrical current. • Part number is based on number of heat pump's to be controlled. Call AquaCar Customer Support for assistance with correct configuration. External Flow Relay (Grid Flow) Switch Kit (0040s) o Used when the pool / spa elevation is higher than the heat pump. o Used when a variable two -speed filter pump set on low -speed mode does not provide enough water pressure to activate a heat pump's water pressure switch. o Also used for automatic pool / spa thermostat switching. PLEASENOTE - The 0040s is not to be used on applications exceeding 50 PSI. Page - 22 Liquid Blankets o An invisible liquid heat barrier designed to retain heat and extend the swimming season. AquaCal" recommends the Aqua Blanket'r". Plumbing Unions: SIZE I PART NIT �B1E18 2INCH 1 2627 Remote Control Kit (STKO070) A remote (wired) control kit allows for full control of the heat pump from up to 100 feet from the equipment. Page - 23 e��jPro�eries SCANNED BY St. Lucie County RECEIVED APR 15 2019 ST. Lucie County, Permitting OWNER'S MANUA _ _ I_LE COPY ENGLISH I FRANI;AIS I ESPANOL Jandy Pro Series Nicheless LED Underwater Light FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the productwill be installed where such state or local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment Installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and Instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/or operation will void the warranty. P' Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property damage, or death. ATTENTION INSTALLER - This manual contains important information about the installation, operation and safe use of this product This information should be given to the owner/operator of this equipment. Page 2 1611MMMINIL Nicheless Underwater LED Lights I Owner's Manual - Table of Contents ,,: Contents Section 1. Important Safety Instructions ....... 3 Section 2. Installing the Jandy° Pro Series Nicheless LED Light......................4 2.1 Preparing the Light Fixture for Installation .....................5 2.2 Installing the Light Fixture............................................6 Section 3. Wiring Options for Controlling Jandy Pro Series Nicheless LED Lights......................................7 3.1 Wiring to an AquaLinV RS Control System..................7 3.2 Wire Gauge and Length................................................8 3.3 Wiring to a Switch..........................................................9 3.4 Twelve (12) Volt Installation...........................................9 Section 4. Jandy Pro Series Nicheless Underwater LED Light Operating Instructions..................................10 4.1 Light Synchronization..................................................10 4.2 Operating the Light......................................................11 Section 5. Designer Lens Series Options .... 12 Section 6. Light Cartridge Replacement ...... 13 Section 7. Winterizing....................................14 Section B. Troubleshooting ...........................15 Wheless Underwater LED lights I Owner's Manual Page 3 Section 1. Important Safety Instructions IMPORTANT SAFETY -INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: A DANGER RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This underwater light must be installed by a licensed or certified electrician in accordance with the National Electrical Code® and applicable local codes and ordinances. In Canada, the Canadian Electrical Code and all applicable local codes and ordinances must be adhered to. Improper installation will create an electrical hazard, which could result in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Read and follow the specific instructions below. A WARNING Before installing this underwater light, read and follow all warning notices and instructions accompanying this light. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Visit www.zodiacpoolsystems.com for additional free copies of these instructions or call Zodiac Technical Support at 800.822.7933 (U.S.) or 888.647.4004 (Canada) CAUTION Except when the Jandy° Pro Series Nicheless Underwater LED Lights are installed in an area of the swimming pool that is not used for swimming and the lens is adequately guarded to keep any person from contacting it, the light shall be installed in or on a wall of the pool, with the top of the lens opening not less than 4 inches (102 mm) below the normal water level of the pool. ATTENTION INSTALLER This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment. SAVE THESE INSTRUCTIONS Page 4 11MEOft Nicheless Underwater LED Lights I Owner's Mannal A WARNING RISK OF. ELECTRICAL SHOCK ELECTROCUTION,OR___ which_ _ could result in serious injury or death. The Jandy® Pro Series Nicheless LED Lights are only available for 12-volt AC power. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated and listed by a NRTL for swimming pool use. Section 2. Installing the Jandy Pro Series Nicheless LED Light A WARNING Risk of Electrical Shock or Electrocution. This underwater light must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code® (Canadian Electrical Code, in Canada) and all applicable local codes and ordinances.. Improper installation will create an electrical hazard, which could result in death or serious injury to pool or spa users, installers or others due to electrical shock, and may also cause damage to property. Always disconnect the power to the light at the circuit breaker before installing or servicing the light. Failure to do so could result in death or serious injury to serviceman, pool or spa users or others due to electrical shock. Use the chart below to determine the appropriate pipe length for your installation. WATTS MINIMUM LENGTH FOR 1.5" PIPE JLU4C9W 9W 3" JLUW9W 9W 3" JLU4C20W 20W 9" JLUW20W 20W 9" JLU4C30W 30W 14" JLUW30W 30W 14" All products listed above come in a variety of cord lengths. Typical cord lengths are 50, 100, & t50 feet NOTE: The lights are servicable - do not remove the enclosure or cord from the conduit. No separate ground or bonding wire is required for the JLU4C9W, JLUW9W, JLU4C20W, JLUW20W, JLUW30W or JLU4C30W low voltage lights which do not have any exposed metal. Nicheless Underwater LED Lights.I Owner's Manual Page 5 2.1 Preparing the Light Fixture for Installation -- NOTE: -The -electrician must complete preparatory steps before -light- - - fixture is installed. See Figure 1. Verify that the pool meets the requirements of the current National Electri- cal Code® (Canadian Electrical Code, in Canada) and all local codes and ordinances. A licensed or certified electrician must install the electrical system to meet or exceed those requirements before the underwater light is installed. Some of the requirements of the National Electrical Code, which the pool electrical systems must meet, are as follows: 1. The junction box or the low -voltage transformer must be located at least eight (8) inches (measured from the inside of the bottom of the junction box or transformer) above the MAXIMUM water level, OR at least four (4) inches above the ground level or pool deck, whichever is greater. The junction -box or transformer must also be installed at least forty-eight (48) inches (4 ft.) from the edge of the pool. See Figure 1. 2. A standard 1.5" plastic wall / return fitting (not included) must be installed so that the top edge of the underwater light's lens is at least 4 inches (10.2 cm) below the surface of the water in the pool. See Figure 1. NOTE: To be certain that the pool's electrical system meets all applicable requirements, the electrician should also consult the local building department. 12 VAC Class 2 Transformer or (Junction Box 1 45' min. CM&AWW.ffie,kb. quire. j B' minimum to maximum water level i.:i%PO[' OLE 4Y.iiEF UUEE It a(appy\ *x+x ' min to top of lens 1.5' pipe through bond Rigid 1' Rigid Electrical — beam and a minimum length Conduit Sweep elbows _ for each style light only, no so- elbows. _ (See Light Info Charts, p.4) NOTE VeNwl InstanationssuM az cenN enawaA<w bralbnswl9 uzeALLol Ne same tleamnce sepu'vemenis Figure 1. Jandy® Pro Series LED Light Installation with Standard 1.5" Plastic Fitting Page 6 Nicheless Underwater LED Lights I Owner's W imial 2.2 Installing the Light Fixture NOTE: Perform these steps only after the electrical system requirements are met. 1.5" pipe must be installed through the bond beam with a minimum length of 14", followed by 1" conduit with sweeps only without 90 degree elbows. It is highly recomended to use 1.5" pipe throughout the entire width of the bond beam. NOTE: Gaskets help ensure that conduit is not a potential leak path. For vinyl wall fittings use both rubber gaskets. For�,rt�';� gunde and fiberglass remove the small gasket and use the Lart�e Gazket large one only. smau casket Flat Gasket See chart on ...._ page 4 for min. 4'MIN. FROM WATER length requirements LEVEL TO TOP OF LENS V minimum I rigid conduit 1.5° Pipe No 99 degree elbows 1.5'THREADED WALL FITTING Figure 2. Standard installation with 1.5" pool wall fitting 2. Snake the 2-Conductor electric cord through the conduit outlet of the wall fitting, into the conduit and up to the location of the 12VAC pool transformer. Cut off cord after allowing for service and length of run to the transformer. 18"-24" of excess cord is recomended for the service loop. Pull the fixture snug to the wall fitting. NOTE: When using a 1 1/2" MIP fitting on the back of a SP-1022 or SP-1408 Wall Fitting, the interior of the Spears and Dura MIP are too small for use with the JandyO Pro Series Nicheless LED Lights. Using the included Lens Key, thread the light into the wall fitting until it is snug. Please provide the pool owner with minimum of 1 key upon job completion. o'Nen Nicheless Underwater LED Lights i Owner's Manual Page 7 ___I. _ __ _ __ 72VACPool for moeer. _ See fable 32 for more details - NOTE: Sentce "1 Loop not applicable rd! for Junction Box Installations. /La'MM.FROM . L EVELTO TOP OF LENS LmNailb tZVAC eiwlaan for Figure 3. Standard installation with IS' pool wall fitting Section 3. Wiring Options for Controlling Jandy® Pro Series Nicheless LED Lights NOTE: Always consider the cable length when calculating the input voltage at the transformer. The maximum run of service between transformer and lights should not exceed 150ft. in length, inclusive of the use of J Box. or not. To the extent allowed by local installation codes in effect in the installation jurisdiction and capacity of the electrical equipment, multiple Jandy Pro Series lights may be controlled with a single switch and transformer so their colors may be synchronized. IMPORTANT NOTE: All fixtures must be tied into the same transformer, circuit or switch for synchronization to occur. The use of Solid Core over Stranded wire and terminating Bus Bars is strongly recomended. 3.1 Wiring to an AquaLink® Controller The Jandy Pro Series Nicheless LED Lights can be controlled by an AquaLink controller. Connect the transformer powering the lights to one of the auxiliary relays in the'AquaLink. Refer to Figure 4 to connect the Jandy Pro Series Nicheless LED Lights to the Power Center. Page 8 Nicheless Underwater LED Lights I Owner's Manual 3.2 Wire Guage and Length - CAUTION Jandy® Pro Series Nicheless Underwater LED Lights are low voltage fixtures. Improper wire guage and wire length can effect the performance of these products. Follow the guidelines below to determine the, proper operation and optimum performance of the lights. Voltages are determined by the measured voltage level at the Bus Bar where the transformer and cords are connected. NOTE: Each color mode has a slightly different power draw JLU4C9W/JLUW9W/JLU4C20W/JLUW20W Min/Max Voltage per cord length Cord Length Min. Voltage Max. Voltage 50 Feet 9AVAC 12AVAC 100 Feet 10.7VAC 13.2VAC 150 Feet 11.82VAC 13.8VAC JLU4C30W & JLUW30W Min/Max Voltage per cord length Cord Length Min. Voltage I Max. Voltage 50 Feet 10.34VAC 112.56VAC 100 Feet 10.9VAC 113.5VAC 150 Feet 11.43VAC 114AVAC A WARNING RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which could result in serious injury or death. A Ground Fault Circuit Interrupter (GFCI) must be provided for 120 Volt transformers. The conductors on the load side of the GFCI circuit shall not occupy conduit, boxes, or enclosures containing other conductors unless the additional conductors are also protected by a GFCI. Refer to local codes for complete details. A WARNING RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which could result in serious injury or death. The Jandy Pro Series Nicheless LED Lights are only available for 12-volt AC power. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated and listed by a NRTL for swimming pool use. Nicheless Underwater LED Lights I Owner's Manual Page 9 3.3 Wiring -too -a -Switch - - The Jandy® Pro Series Nicheless LED Lights can be wired to a switch to manually operate the lights. Refer to Figure 4 to connect the lights into the. switch. Figure Automation Auk Relay or Switch V '^ N L m Line Black Black Neutral White Whitenanffnter Ground Ground Gree 4. Wirina Jandv Pro Series Nicheless Underwate 3.4 Twelve (12) Volt Installation r Liahts A 12-14 Volt AC Transformer must be used to power all 12-Volt lights. NOTE For optimum performance Jandy Pro Series recommends not exceeding the load factor specified by the instructions included with the transformer. To ensure maximum safety; use only a Class 2 transformer that can supply 12-14 Volts AC to power all 12-Volt lights. The transformer must be listed or certified by a Nationally Recognized Testing Laboratory (NRTL) for the intended use. A CAUTION To prevent risk of fire which could result in property damage, and to ensure optimum performance, do not exceed the load factor specified in the instructions provided by the transformer manufacturer. Page 10 Nicheless Underwater LED Lights i Owner's Manual Figure 5. Wiring LED Lights to a 12 Volt Transformer NOTE A dimmer switch or dimming relay may be used when Jandy Pro Series Nicheless WHITE ONLY lights are installed. Jandy Pro Series color lights are NOT DIMMABLE and are NOT COMPATIBLE with dimmer switches or dimmer relays. Section 4. Jandy® Pro Series Nicheless Underwater LED Light Operating Instructions 4.1 Light Synchronization NOTE This section only applies to the color (RGBW) lights. All fixtures must be tied into the same transformer, circuit or switch for synchronization to occur. 1. Turn the light ON. If the light has been off for 7 seconds or longer, the light will turn on at the last color selected. 2. To synchronize multiple lights to the same color mode, you will need to reset to the beginning of the color mode sequence. With the lights ON, turn them OFF for five (5) seconds, then turn ON again. All of the lights will reset to the Alpine White color mode. If all of the lights are not in the Alpine White color mode, they have not been synchronized, repeat step 2. Nicheless Underwater LED Lights I Owner's Manual Page 11 4.2 Operating the Light 3. To change the color mode, turn the light OFF for one 1-3 seconds. Continue turning OFF and ON until the desired light color mode is reached. See Table 1 for the color mode sequence. Example: If you followed step 3 and are now on Sky Blue and want the lights to be Violet, then the lights must be turned off and on 7 seven times to bring you to Violet. Sequence Order Color Modes 1 Alpine White 2 Sky Blue 3 Cobalt Blue 4 Caribbean Blue 5 Spring Green 6 Emerald Green 7 Emerald Rose 8 Magenta 9 Violet 10 Slow Color Splash 11 Fast Color Splash 12 America the Beautiful 13 Fat Tuesday 14 Disco Tech Table 1. Color Mode Sequence 4. The lights have memory. If the lights are off for 7 seconds or more, the next time the lights are turned on, they will return to the last color mode they were on prior to being turned off (Step 1 listed above). This function allows you to keep your lights returning to your favorite color mode every time the lights are turned back on. NOTE To synchronize colors on multiple Jandy® Pro Series Nicheless Underwater LED Light systems wired to separate switches, perform the above actions on all of their switches simultaneously. All Jandy Pro Series Nicheless Underwater LED Lights will synchronize automatically if activated by the same switch. No other accessories are required. Page 12 Nicheless Underwater LED Lights I Owner's Manual Section 5. Designer Lens Options The Designer Lenses offer a unique set of options for the LED Series of lights. Each one has the ability to create unique lighting effects within the pool's interior. See the list below to learn more about the designer lens options. P HALF DOME - This escutcheon adds over the existing lens to allow you to direct 1/2 the light in a direction you want. Downwards -to light a pools interior without light shining upwards.. Upwards to light a water feature or sideways to put light where it might be needed but no where else HALO LENS - This lens allows for gentle lighting in an area but knocks down the center beam. This allows for installation on walls, etc. where there might be an opposite wall, etc. where you want to eliminate generating a "hot" spot. Great general lighting but softly. SPOT LENS - Just the opposite of the Halo. Concentrates the light and reduces the output at wider beam angles in order to produce a spot -light effect. Great for illuminating that special feature. CATS EYE - This lens reduces the light to just a "slice" of light that is broad but thin. An incredible effect for illuminating but without spilling light all over. DIAMOND - WOW want to really create something special? The Diamond lens creates incredible points of light throughout the interior. The points will be different the farther away from the light they are. Put the LED colored light on DISCO TECH MODE AND WATCH THE FUN BEGIN! Nichetess Ondenvater LED Lights I Owner's Manual 0 Page 13 Section 6. Light Cartridge Replacement ® WARNING RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which could result in serious injury or death. The Jandy® Pro Series Nicheless LED Lights are only available for 12-voltAC power. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated and listed by a NRTL for swimming pool use. Always disconnect the power to the light at the circuit breaker before installing or servicing the light. Failure to do so could result in death or serious injury to serviceman, pool or spa users or others due to electrical shock. 1. Verify that the light has been disconnected from the power source and be sure that the light fixture is in a dry environment. Remove the eight (8) screws from the lens with the tool provided. Pull the lens from the fixture body. Remove and discard the 0-ring between the Lens and Fixture Body. 2. Using the tool provided, insert and turn the threaded portion into the extraction hole in the face of the light cartridge. Pull the light cartridge from the housing body. 3. Insert the replacement cartridge into the housing body. Line up the TAB at the end of the circuit board with the receiving slot inside the housing body. It may be necessary to slowly turn the light cartridge until the TAB lines up with the slot. i .wy F i a o Page 14 Nicheless Underwater LED Lights I Owner's Manual 4. Clean the lens and the enclosure of any remaining old silicone before applying new silicone and -replacing the lens,. Replace the_O-ring with the new one provided. Attach the lens onto the fixture body. Tightly secure the eight (8) screws indicated in the diagram below. Once all screws are tight, slowly submerse in water, checking for any air bubbles - quickly remove from water bubbles appear as it indicates the seal is not water tight. retighten the screws and test for bubbles again. SILICONE BEAD ON LENS SCREW TIGHTENING DIAGRAM Apply a new silicone bead to the lens with tube provided after cleaning the lens and body of old silicone. 5. Reset the fixture into the wall fitting and turn the power ON. Section 7. Winterizing The water level should be lowered to approximately 12 inches below the pool lights. Make certain that the water is drained out of the wall housing. Consult a Local Swimming Pool Professional for proper winterization. Minimum safeguard requires dropping the water level 2"-4" below the light. At NO TIME should there be water removed from the pool without checking ground water tables. Nicheless Underwater LED Lights I Owner's Manual Section 8. Troubleshooting Page 15 Use the troubleshooting information in the following table for suggestions. .. .-Problem -CorrectiveAction AII-lights fail to illuminate -Lights-are not-reciev= Check-120VAC power supply ing power into transformer. Check for 12VAC output at transformer. Check or reset GFCL Make sure 120 volts has not been used in the installation - damage is assured and is NON WARRANTY. One or more lights are Poor connection or Separate each light and dim, blinking or not improper wire gauge independently wire 12V to the working single light only. Repeat this process on each light. If junc- tion box is being used, check for proper connection of light cord. Verify that the correct wire guage is being used between the transformer and junction box. Colored lights out of Improper voltage Verify that proper wire connec- synch supply or poor con- tions are being achieved for nection to the light the lights that are out of synch. Reset all the lights to white by turning lights OFF for five (5) seconds, then turning ON Jandy® Pro Series Nicheless Underwater LED Lights are field servicable and the cord and light body fixture should not be removed completely from the conduit or pool. There should be enough cord supplied in the service loop to remove light from wall fitting and lifted above water level for LED light cartridge replacement. If there is not enough cord in service loop or it cannot be accessed, pool water can be drained below light to access front of light.