The URL can be used to link to this page

Home My WebLink AboutNOAMIAMF • M MH-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami. Florida 33175-2474 Nn-fffTTi n>r A nd WW W V A ,..�.a — T (786)315-2590 F (786) 31525-99 Tarco Specialty Products, Inc. One Information Way Suite 225 Little Rock, AR 72202 SCANNED BY .SCOPE' ST. Lucie County, N' mi-aing � St. Lucie County This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to he used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the A14J (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. APR 2 3 '019 DESCRIPTION: Turco Self -Adhering Modified Bitumen Roofing Systems over Wood Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product TERNMATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terntinate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA- ( ADVERTISEMENT: The NOA number preceded, by the words Miami -Dade County, Florida, and followed bytheexpiration date may be displayed in advertising literature. If any portion of the NOA is di la then it shall be done ;n its entirety. R�/1��!l��AE��D'' 1FOpR� INSPECTION: A copy of this entire NOA shall be provided to the user by the man rYM itWANCE shall be available for inspection at the job site at the request of the Building Official. ST. LU CI E COUNTY This NOA renews NOA No. 12-0703.06 consists of pages 1 through 10. BOCC-0 The submitted documentation was reviewed by Alex Tigem. . M ECOUNTY NOA No.: 18-0919.04 ' FILE �OF�prrationDate: 11/08/23 pproval Date: 10/25/18 Page I of 10 —firm P.OsoG1 vVC. 111 wr1 \-I P. R 64 I() ROOFING SYSTEM APPROVAL Ca o : Roofing Snb-Cateeorv' Modified Bitumen Material SBS Deck Tvpe• Wood Maximum Design Pressure: -60.0 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Dimensions LeakBarrier® 3' x 133'4" rolls EasyLay LeakBarrier' 3' x 72' rolls EasyBase LeakBarrier' 3' x 36' rolls EasyStick Plus' t LeakBarrier® 3' x 72' rolls EasyTorch' SA Base Le"arrier" 39 3/8" EasyTorch'" APP x 32' 10" rolls Smooth LeakBarrielm 39 3/8" EasyTorcb APP x 32' 10" rolls Granular APPROVED INSULATIONS: Product Name Test Product Specification Description ASTM D 226 Mechanically attached, asphalt coated Type H polyester base sheet. ASTM D 4601, Type I Self -adhered, fiberglass reinforced, smooth surfaced SBS modified bitumen base ply membrane. ASTM D 6164, Type I Self -adhered, polyester reinforced, granule surfaced SBS modified bitumen cap ply membrane. ASTM D 4601 Self -adhered, glass fiber reinforced, smooth Type H surfaced, SBS modified bitumen base ply membrane. ASTM D 6222, Polyester reinforced, smooth surfaced, APP Type I modified bitumen torch applied cap membrane. ASTM D 6222, Polyester reinforced, slate flake surfaced, APP Type I modified bitumen torch applied cap membrane. TABLE2 Product Description SECUROCK Gypsum -Fiber Roof Board Rigid, gypsum -based board stock MUU11•DADECOUNTY ,.... my Manufacturer (With Current NOA1 United States Gypsum Corporation. NOA No.:18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 2 of 10 APPROVED FASTENERS: Fastener Product Number Name 1. #12 Standard Roofgrip, OMG Heavy Duty TABLE 3 Product Description Dimensions Roofing and insulation fasteners, Various with #3 Phillips head. 2. OMG 3" Galvalume Steel Galvalume steel stress plates. 3" round Plate 3. Trufast #12 DP Fastener Insulation fastener for wood, steel and concrete 4. Trufast #14 HD Fastener Insulation fastener for wood, steel and concrete 5. Trufast 3" Metal Insulation Galvalume steel stress plate 3" round Plate EVIDENCE SUBMITTED: Test Agency Test Identifier Test Name/Report Southwest Research 10.16924.01.220a ASTME108 Institute 10.16924.01.220b ASTM E108 Trinity I ERD NEMOjetc. T39040.11.11-R1 T43940.05.13-R1 T43410.05.13-RI T35450.12.11-R1 TAR-SC13965.02.17-RI TAR-SC16545.11.17 4-TAR-18-002.04.18 TAS 114 (H) ASTM D6222 / TAS 110 ASTM D4601 ASTM D6222 / TAS 110 ASTM D226 ASTM D4601 ASTM D6164 / TAS 110 Manufacturer (With Current NOA) OMG, Inc. OMG, Inc. Altenloh, Brinck & Co. U.S., Inc. Altenloh, Brinck & Co. U.S., Inc. Altenloh, Brinck & Co. U.S., Inc. Date 11/02/12 11/02/12 11/21/11 05/01/13 05/23/13 6/02117 02/27/17 11/01/17 04/16/18 MIAMFDADE COUNTY NOA No.: 18-0919.04 . • • • . , Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 3 of 10 APPROVED ASSEMBLIES Membrane Type: SBS Deck Type 11- Wood, Insulated Deck Description: 19/32 or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spared maximum 24" o.c. System Type C(1): All layers of insulation are mechanically attached to roof deck All General and System'Limitations apply. One or more layers of the following: Insulation Laver Insulation Fasteners Fastener Table 3 Density/fe SECUROCK Gypsum -Fiber Roof Board Minimum 3/8" thick 1 (#12), 2. 3, 4, 5 1:1 fe Note: Base layers of insulation shall be mechanically attached using the fastener density listed. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: One ply ofLeakBarrier®EasyBase self -adhered. Ply Sheet: (Optional) One ply of LeakBarrier®EasyBase self -adhered. Cap Sheet: One ply of LeakBarrier®Easysticr Plus self -adhered. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA. 1. Gravel or slag at 400 lbs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 lbs/sq. 2. Karnak 97 Fibrated Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1 % gal/sq. Maximum Design -52.5 psf (See General Limitation #7.) Pressure: NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 4 of 10 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: 19/32" or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spaced maximum 24" o.c. System Type C(2): All layers of insulation are mechanically attached to roof deck. All General and System Limitations apply. One or more layers of the following: Insulation Laver Insulation Fasteners Fastener SECUROCK Gypsum -Fiber Roof Board able 3 Density/112 Minimum 3/8" thick 1 (#12),2,3,4,5 1:1 if Note: Base layers of insulation shall be mechanically attached using the fastener density listed. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment Base Sheet: One ply ofLeakBarrier®EasyBase self -adhered Ply Sheet: (Optional) One ply LeakBarrier® EasyTorcW' SA Base self -adhered or one ply of LeakBarrier®EasyTorchTM APP Smooth, torch applied. Cap Sheet: One ply of LeakBarrief®EasyTorcN" APP Granular, torch applied. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA. 1. Gravel or slag at 400 Ibs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 Ibs/sq. 2. Karnak 97 Fibrated Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1'/2 gal/sq. Maximum Design -52.5 psf (See General Limitation #7.) Pressure: APPROVED NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 5 of 10 Membrane Type: SBS Deck Type 1I: Wood, Insulated Deck Description: 19/32" or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spaced maximum 24" o.c. System Type D(1): All layers of insulation are mechanically attached to roof deck. All General and System Limitations apply. One or more layers of the following: Insulation Laver Insulation Fasteners Fastener able 3 Density/W SECUROCK Gypsum -Fiber Roof Board Minimum 3/8" thick N/A N/A Base Sheet: One or more plies of LeakBarrier® EasyLay', mechanically attached 10" o.c, in the min. 4" lap and 10" o.c, in two, equally spaced, staggered center rows with #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3" Galvalume Steel Plates. Ply Sheet: One ply of LeakBarrier® EasyBase' self -adhered. Cap Sheet: One ply ofLeakBar ier®EasyStick Plus self -adhered. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA. 1. Gravel or slag at 4001bs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 Ibs/sq. 2. Karnak 97 Fibmted Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1'/: gal/sq. Maximum Design -60 psf (See General Limitation #7.) Pressure: NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 6 of 10 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: 19732° or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spaced maximum 24" o.c. System Type D(2): All layers of insulation are mechanically attached to roof deck. All General and System Limitations apply. One or more layers of the following: Insulation Laver SECUROCK Gypsum -Fiber Roof Board Insulation Fasteners Fastener able 3 Density/fO Minimum 3/8" thick N/A NIA Base Sheet: One or more plies of LeakBarrier® EasyLay'", mechanically attached 10" o.c. in the min. 4" lap and 10" o.c. in two, equally spaced, staggered center rows with #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3" Galvalume Steel Plates. Ply Sheet: One ply of LeakBarrier® EasyTorch' SA Base splf-adhered or one ply of LeakBarrier® EasyTorch APP Smooth, torch applied. Cap Sheet: One ply of LeakBar ier® EasyTorch' APP Granular, torch applied. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA_ 1. Gravel or slag at 400 lbs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 lbs/sq. 2. Karnak 97 Fibrated Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1 %s gallsq. Maximum Design -60 psf (See General Limitation V.) Pressure: NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 7 of 10 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: 19/32" or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spaced maximum 24" o.c_ System Type E(1): Base sheet mechanically fastened. All General and System Limitations apply. One ply of LeakBarrier® EasyLay' fastened to the deck as described below. OMM Attach base sheet using 12 ga. annular ring shank nails with min. 32 ga., 1-5/8" diameter tin - caps spaced 7" o.c. in the 4" lap and 7" o.c. in three, equally spaced, staggered center rows. Fastening #2: Attach base sheet using #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3" Galvalume Steel Plates or Trufast #12 DP or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 10" o.c. in the min. 4" lap and 10" o.c. in two, equally spaced, staggered center rows. One ply of LeakBarrierl FasyBase' self -adhered. One ply of LeakBarrier® EasyStick Plus' self -adhered. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA. 1. Gravel or slag at 400 lbs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 lbs/sq. 2. Karnak 97 Fibrated Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1'/2 gal/sq. Maximum Design -60 psf (See General Limitation #7.) Pressure: NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10 5/18 Membrane Type: SBS/APP Deck Type 1I: Wood, Non -Insulated Deck Description: 19432" or greater plywood or wood plank attached with 8d common nails spaced 6" o.c. at wood joists spaced maximum 24" o.c. System Type E(2): Base sheet mechanically fastened. All General and System Limitations apply. Base Sheet: One ply of LeakBarrier® EasyLay'a fastened to the deck as described below. Fastening #1: Attach base sheet using 12 ga. annular ring shank nails with min. 32 ga., 1-518" diameter tin - caps spaced 7" o.c. in the 4" lap and 7" o.c. in three, equally spaced, staggered center rows. Fastening #2: Attach base sheet using Trufast #12 DP or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 10" o.c. in the min. 4" lap and 10" o.c. in two, equally spaced, staggered center rows. Ply Sheet One ply of LeakBarriet'a EasyTorchm SA Base self -adhered or one ply of LeakBarrier® EasyTorchTm APP Smooth, torch applied. Cap Sheet: One ply of LeakBarrier® EasyTorchTm APP Granular, torch applied. Surfacing: (Optional) Install one of the following to obtain required fire classification. Any coating, listed below, used as a surfacing, must be listed within a current NOA. 1. Gravel or slag at 4001bs/sq or 300 lbs/sq, respectively, in a flood coat of approved asphalt at 60 lbs/sq. 2. Karnak 97 Fibrated Aluminum Asphalt Roof Coating or Asbestos Free Aluminum Roof Coating at 1'/2 gal/sq. Maximum Design -60 psf (See General Limitation #7.) Pressure: nwnuoaoe couornr NOA No.: 18-0919.04 Expiration Date: 11/08/23 Approval Date: 10/25/18 Page 9 of 10 WOOD DECK SYSTEM LIMITATIONS: 1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet. GENERAL LimrrATIoNs: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2_ Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbsJsq. Note: Spot attached systems shall be limited to a maximum design pressure of 45 psf. S. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F) value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida Registered Engineer, Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and comer areas shall -comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with'Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter milers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and 'applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and comers). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE MIAMMADE COUNiY NOA No.: 18-0919.04 Expiration Date: 11/0Sl23 Approval Date: 10/25/18 Page 10 of 10 MIAMI.OA6E av DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DMSION M MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 209 Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 www.miamidade.eov/econRm1 TAMKO Building Products, Inc. RECEIVED SCANNED 220 West 4th Street BY Joplin, MO64801 APR 2 3 2019 St. Lucie County SCOPE: ST. Lucie County, Permittinn This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: TAMKO Roof Shingles LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. �q �, A4 a FOR INSPECTION: A copy of this entire NOA shall be provided to the user b�e manufacturer or-its-diStM T end shall be available for inspection at the job site at the request of the Building Ol&ial. " r N'� .s +e This NOA revises and renews NOA Ne.14-0306.02 and consists of pages 1 through 6. The submitted documentation was reviewed by Gaspar J Rodriguez. MIAMI•DADECOUNTY i NOA No.:15-0709.19 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub -Category: Asphalt Shingles Materials: Laminate Deck Type: Wood SCOPE This approves TAMKO's Heritage, Heritage Woodgate and Heritage Premium asphalt shingles, manufactured by TAMKO Building Products, Inc., as described in this Notice of Acceptance and designed to comply with the Florida Building Code High Velocity Hurricane Zones. PRODUCT DESCRIPTION Product Dimensions Test Product Description Specifications Heritage 13 %4 " x 39'/8" TAS 110 Dimensional asphalt shingle. Manufacturing Location # 1, 2, 3 Heritage Woodgate 13 %4 "x 39'/s" TAS 110 Dimensional asphalt shingle. Manufacturing Location # I Heritage Premium 13 % " x 391/8" TAS 110 Dimensional asphalt shingle. Manufacturing Location # 1, 2 MANUFACTURING LOCATIONS 1. Dallas, TX 2. Tuscaloosa, AL 3. Frederick, MD EVIDENCE SUBMITTED Test Agency Test Identifier Test Name/Report Date Underwriters Laboratories, Inc. TAS 107 & UL 790 04CA44252 02/25/05 ASTM D3462 02NK33813 09/23/02 ASTM D 3462 & TAS 107 R2919 Letter 03/10/11 ASTMD3462 4789110543 08/26/14 TAS 107 02/19/15 ASTM E 108 08/26/14 ASTM D3161, Class F 4787043752 10/20/15 PRI Asphalt Technologies, Inc. TAS 100 TAP-129-02-01 05/26/05 TAS 100 TAP-130-02-01 05/26/05 TAS 100 TAP-131-02-01 05/26/05 TAS 100 TAP-303-02-01 12/12/14 TAS 100 TAP-307-02-01 02/10/15 TAS 100 TAP-317-02-01 09/02/15 MIAMMADE COUNTY NOA No.:15-0709.19 Expiration Date: 12/01/20 Approval Date: 11/12/15 Page 2 of 6 LIMITATIONS 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Shingles shall not be installed on roof mean heights in excess,of 33 ft. 3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. INSTALLATION I. Shingles shall be installed in compliance with Roofing ApplicationStandard RAS 115. 2. Flashing shall be in accordance with Roofing Application Standard RAS 115. 3. The manufacturer shall provide clearly written application instructions. 4. Exposure and course layout shall be in compliance with Detail 'A', attached. 5. Nailing shall be in compliance with Details 'B', attached. LABELING Shingles shall be permanently labeled with the manufacturer's name and/or logo, city and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control Approved" or with the Miami -Dade County Product Control Seal as seen below: MIAMl-DADE COUNTY BUILDING PERMIT REQUIREMENTS As required by the Building Official or the applicable Building Code in order to properly evaluate the installation of this system. This Notice of Acceptance on its own cannot be used to obtain a building permit. MAW DADE COUNTY NOA No.: 15-0709.19 Expiration Date: 12/01/20 Approval Date:11/12/15 Page 3 of 6 DETAIL A HERITAGE, HERITAGE WOODGATE, AND HERITAGE PREM UM All dimensions are In inches. STH COURSE 4TH COURSE 3RD COURSE 2ND COURSE — 23 1ST COURSE zs Fun 1 1 : HERITAGE SBMXGLE FIG. I FASTENING PATTERN All dimensions are in inches - 39-3/8" • 7'�' �I< 7'/="—� 7 3/e" 7 F'" 7'�" 1" 13 ----------I ----------SIG ---- -- ------------------------------------------------- C E 1/4" -5/8" KPOSUfe MIAMMM=E COUNTY NOA No.:15-0709.19 ' Expiration Date: 12/01/20 Approval Date:11/12115 Page 4 of 6 DETAIL B (CONTINf7ED) HERITAGE SHINGLE FIG. 2 ALTERNATE FASTENING PATTERN ttl"It': 12•Il?."—.; + 1?-t12"-r(;:1"�w i ! Q Common Boni I FASTENERS ; _ � m 1 m� �a 1 � x L� s .. 39_3/8" HERITAGE SHINGLE (TUSCALOOSA, AL) FIG. 3 ALTERNATE FASTENING PATTERN HORIZONTAL NAIL SPACING IN ACCORDANCE WITH FIG. 1 OR FIG. 2. VERTICAL NAIL SPACING ALLOWED ANYWHERE WITHIN NAIL ZONE. PAINT LINE,_ .y 7-718 T _ NAILZONE 6-118e DO NOT FASTEN ALONG EDGE OF COMMON BOND PREFERRED FASTENER LOCATION WALMA)ADE COUNTY NOA No.:15-0709.19 • • • Expiration Date: 12/01/20 Approval Date: 11/12/15 Page 5 of 6 ai HERITAGE WOODGATE & HERITAGE PREMIUM SHINGLES FIG. 4 FASTENING PATTERN All dimensions are in inches 1° 7'/z" 6'/2" 6 931e° '/:° ' ° 6IE— 3IE 3IE 3I� �I� ,7/ �IH 13 :------•-------:--------------------- ---------------------------- ------ END OF THIS ACCEPTANCE -1/4" Exposure MUIMFDADE COUNTY NOA No.: 15-0709.19 Expiration Date: 12/01/20 Approval Date.11/12/15 Page 6 of 6