HomeMy WebLinkAboutNOAF � yQ
R V EW D FOR
MI®DARE CODE COMPLIANCE MIAMI-DADE COUNTY
ST, LUC �Q �TY PRODUCT CONTROL SECTION
i(� (� 11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND EC SOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/economy
GAF
1 Campus Drive SCANNED
Parsippany, NJ 07054 BY
SCOPE: St. Lucie County
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the
Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product
Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County)
reserve the right to have this product or material tested for quality assurance purposes. If this product or
material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing
and the AHJ may immediately revoke, modify, or suspend the use of such product or material within
their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade
County Product Control Section that this product or material fails to meet the requirements of the
applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: GAF Ruberoid®Modified Bitumen Roof System for Wood Decks.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state
and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted
herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has
been no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or
change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an
endorsement of any product, for sales, advertising or any other purposes shall automatically terminate
this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of
NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and
followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is
displayed, then it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No. 15-1020.01 and consists of pages 1 through 67.
The submitted documentation was reviewed by Jorge L. Acebo.
MLCMIAADE COUNTY
ummen
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 1 of 67
ROOFING SYSTEM APPROVAL
Category:
Roofing
Sub -Category:
Modified Bitumen
Material:
APP/SBS
Deck Type:
Wood
Maximum Design Pressure:
-105 psf.
TRADE NAMES OF PRODUCTS
MANUFACTURED OR LABELED BY APPLICANT:
TABLE
Test
Product
Product
Dimensions
Specification
Description
GAFGLAS® Ply 4
39.37"
ASTM D2178
Smooth surfaced asphaltic ply sheet
(1 meter) Wide
reinforced with fiberglass mat.
Tri-Ply® Ply 4 Ply Sheet
39.37"
ASTM D2178
Smooth surfaced asphaltic ply sheet
(1 meter) Wide
reinforced with fiberglass mat.
GAFGLAS®
39.37"
ASTM D2178
Smooth surfaced asphaltic ply sheet
FlexPly' 6
(1 meter) Wide
reinforced with fiberglass mat.
GAFGLAS® #75 Base Sheet
39.37"
ASTM D4601
Smooth asphaltic base or base/ply sheet
(I meter) Wide
reinforced with fiberglass mat.
Tri-Ply® #75 Base Sheet
39.37"
ASTM D4601
Smooth asphaltic base or base/ply sheet
(1 meter) Wide
reinforced with fiberglass mat.
GAFGLAS® #80 Ultima' Base
39.37"
ASTM D4601
Smooth asphaltic base or base/ply sheet
Sheet
(1 meter) Wide
reinforced with fiberglass mat.
GAFGLAS® Stratavent®
39.37'
ASTM D4897
Smooth surfaced asphaltic perforated
Perforated Venting Base Sheet
(I meter) Wide
venting base sheet reinforced with
fiberglass mat.
GAFGLAS® Stratavent®
39.37"
ASTM D4897
Smooth surfaced asphaltic nailable venting
Nailable Venting Base Sheet
(l meter) Wide
base sheet reinforced with fiberglass mat.
Bottom side surfaced with granules.
Ruberoid® HW 25 Smooth
39.37'
ASTM D6163
Smooth surfaced torch applied SBS base
(1 meter) Wide
or ply sheet reinforced with a fiberglass
mat.
Ruberoid® HW Smooth
39.37"
ASTM D6164
Smooth surfaced torch applied SBS base
(1 meter) Wide
or ply sheet reinforced with a polyester
mat.
Ruberoid® HW Granule
39.37"
ASTM D6164
Granule surfaced torch applied SBS cap
(1 meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® HW Granule FR
39.37'
ASTM D6164
Fire retardant granule surfaced beat -
(I meter) Wide
welded SBS cap sheet reinforced with a
polyester mat.
Ruberoid® HW Plus Granule
39.37"
ASTM D6164
Granule surfaced torch applied SBS cap
(I meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® HW Plus Granule
39.37'
ASTM D6164
Fire retardant granule surfaced torch
FR
(1 meter) Wide
applied SBS cap sheet reinforced with a
polyester mat.
NOA No.: 18-0919.12
MInM1- 0 COUNTY Fly Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 2 of 67
Test
Product
Product
Dimensions
Specification
Description
Ruberoid® EnergyCap' H W
I meter
ASTM D6164
Fire retardant granule surfaced heat -
Plus Granule FR
(39.37") Wide
welded SBS cap sheet reinforced with a
polyester mat. Cap sheet is factory coated
with TOPCOAT® EnergyCote'
Elastomeric Coating.
Ruberoid® Torch Smooth
39.37"
ASTM D6222
Smooth surfaced torch applied APP base
(1 meter) Wide
or ply sheet reinforced with a polyester
mat.
Tri-Ply® APP Smooth
39.37"
ASTM D6222
Smooth surfaced torch applied APP cap,
Membrane
(I meter) Wide
base or ply sheet reinforced with a
polyester mat.
Ruberoid® Torch Granule
39.37"
ASTM D6222
Granule surfaced torch applied APP cap
(1 meter) Wide
sheet reinforced with a polyester mat.
Tri-Ply® APP Granule Cap
39.37"
ASTM D6222
Granule surfaced torch applied APP cap
Sheet
(1 meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® Torch Plus Granule
39,37"
ASTM D6222
Fire retardant granule surfaced torch
FR
(1 meter) Wide
applied APP cap sheet reinforced with a
polyester mat.
Ruberoid® EnergyCap'
39.37"
ASTM D6222
Fire retardant granule surfaced torch
Torch Plus Granule FR
(1 meter) Wide
applied APP cap sheet reinforced with a
polyester mat. Cap sheet is factory coated
with TOPCOAT® EnergyCote'
Elastomeric Coating.
Ruberoid® EnergyCap'
39.37"
ASTM D6222
Fire retardant granule surfaced torch
Torch Granule FR
(1 meter) Wide
applied APP cap sheet reinforced with a
polyester mat. Cap sheet is factory coated
with TOPCOAT' EnergyCote'
Elastomeric Coating.
Ruberoid® 20 Smooth
39.37"
ASTM D6163
SBS polymer -modified asphalt base or ply
(I meter) Wide
sheet reinforced with a fiberglass mat.
Ruberoid® 30 Granule
39.37"
ASTM D6163
Granule surfaced mop applied SBS cap
(1 meter) Wide
sheet reinforced with a fiberglass mat.
Ruberoid® 30 Granule FR
39.37"
ASTM D6163
Fire retardant granule surfaced mop
(1 meter) Wide
applied SBS cap sheet reinforced with
fiberglass mat.
Ruberoid® 30 Plus Granule FR
39.37"
ASTM D6163
Fire retardant granule surfaced mop
(1 meter) Wide
applied SBS cap sheet reinforced with
fiberglass mat.
Ruberoid® Mop Granule
39.37"
ASTM D6164
Granule surfaced mop applied SBS cap
(I meter) Wide
sheet reinforced with a polyester mat.
Tri-Ply® SBS Granule Cap
39.37"
ASTM D6164
Granule surfaced mop applied SBS cap
Sheet
(I meter) Wide
sheet reinforced with a polyester mat.
Intec Flex PRF
39.37"
ASTM D6164
Granule surfaced mop applied SBS cap
(1 meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® Mop Smooth
39.37"
ASTM D6164
Smooth surfaced mop applied SBS base
(1 meter) Wide
sheet reinforced with a polyester mat.
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/O1/18
Page 3 of 67
Test
Product
Product
Dimensions
Specification
Description
Ruberoid® Mop Smooth 1.5
39.37"
ASTM D6164
Smooth surfaced mop applied SBS base
(1 meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® Mop Plus Smooth
39.37"
ASTM D6164
Smooth surfaced mop applied SBS base or
(I meter) Wide
ply sheet reinforced with a polyester mat.
Ruberoid® Mop Plus Granule
39.37"
ASTM D6164
Granule surfaced mop applied SBS cap
(1 meter) Wide
sheet reinforced with a polyester mat.
Ruberoid® Mop Plus Granule
39.37"
ASTM D6164
Fire retardant granule surfaced mop
FR
(I meter) Wide
applied SBS cap sheet reinforced with a
polyester mat.
Ruberoid® EnergyCar Mop
39.37"
ASTM D6164
Fire retardant granule surfaced mop
Plus Granule FR
(1 meter) Wide
applied SBS cap sheet reinforced with a
polyester mat. Cap sheet is factory coated
with TOPCOAT® EnergyCote'
Elastomeric Coating.
Ruberoid® Mop Granule FR
39.37"
ASTM D6164
Fire retardant granule surfaced mop
(1 meter) Wide
applied SBS cap sheet reinforced with a
polyester mat.
Ruberoid® EnergyCap' 30
39.37"
ASTM D6163
Fire retardant granule surfaced mop
Granule FR
(I meter) Wide
applied SBS cap sheet reinforced with a
fiberglass mat. Cap sheet is factory coated
with TOPCOAT® EnergyCote'
Elastomeric Coating.
GAFGLAS® Mineral -Surfaced
39.37"
ASTM D3909
Granule surfaced asphaltic cap sheet
Cap Sheet
(1 meter) Wide
reinforced with fiberglass mat.
Tri-Ply® BUR Granule Cap
39.37"
ASTM D3909
Granule surfaced asphaltic cap sheet
Sheet
(1 meter) wide
reinforced with a fiberglass mat.
GAFGLAS®EnergyCap'
39.37"
ASTM D3909
Granule surfaced asphaltic cap sheet
Mineral -Surfaced Cap Sheet
(1 meter) Wide
reinforced with fiberglass mat. Cap sheet
is factory coated with TOPCOAT®
EnergyCote'" Elastomeric Coating.
TOPCOAT® Membrane
1, 5 or 55 gallons
ASTM D6083
Water based elastomeric coating.
United Coatings'" Roof Mate
1, 5 or 55
ASTM D6083
Water -based elastomeric coating
TCM Coating
Gallons
TOPCOAT® 5 or 55 gallons ASTM D6083
Surface Seal SB
United Coatings' Surface Seal 5 or 55 Gallons ASTM D6083
SB Roof Coating
TOPCOAT® MB Plus
United Coatings' Roof Mate
MB Plus Coating
5 or 55 gallons
5 or 55 Gallons
Proprietary
Proprietary
Solvent based thermoplastic rubber sealant
designed to protect and restore aged roof
surfaces and to increase roof reflectivity.
Solvent -based thermoplastic rubber
sealant designed to protect and restore
aged roof surfaces and to increase roof
reflectivity.
Water based, low VOC primer used to
block asphalt bleed -through.
Water based, low VOC primer designed to
block asphalt bleed -through.
NOA No.: 18-0919.12
fly =4 Mwnifonoecourrry Expiration Date: 11/06/23
Approval Date: 11/O1/18
Page 4 of 67
Test
Product
Product
Dimensions
Specification
Description
FireOut' Fire Barrier Coating
5 or 55 gallons
Proprietary
Low VOC, water -based fire barrier
coating.
Flex Seal'
1, 5 gallons
TAS 139
Solvent -based elastomeric sealant.
or I qt. tube
VersaShield® Fire -Resistant
12" x 100' rolls
ASTM D226
Non -asphaltic fiberglass -based
Roof Deck Protection
underlayment and /or fire barrier.
VersaShield® Solo' Fire-
42" roll wide,
ASTM D146,
Non -asphaltic, fire resistant fiberglass
Resistant Slip Sheet
100 ft.
D828, D4869,
underlayment
D6757
Matrix'" 102 SBS Membrane
3, 5 or 55 gallons
ASTM D3019
Fiber reinforced rubberized cold -applied
Adhesive
adhesive for modified bitumen roof
systems.
APPROVED INSULATIONS:
Product Name
EnergyGuard' Polyiso Insulation
Table 2
Product Description
Polyisocyanurate foam insulation
EnergyGuard' Tapered Polyiso Insulation Polyisocyanurate foam insulation
EnergyGuard' RA Polyiso Insulation
EnergyGuard' RH Polyiso Insulation
EnergyGuard'" RH Tapered Polyiso
Insulation
EnergyGuard' RN Polyiso Insulation
EnergyGuard' Perlite Recover Board
EnergyGuard' Perlite Roof Insulation
EnergyGuard' RA Composite Polyiso
Insulation
Structodek® High Density Fiberboard Roof
Insulation
SECUROCK® Gypsum -Fiber Roof Board
SECUROCK® Glass -Mat Roof Board
DensDeck® Roof Board
DensDeck® Prime Roof Board
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Perlite recover board
Perlite insulation board
Polyisocyanurate foam insulation
with high density fiberboard or
permalite
High density fiberboard
Gypsum board
Gypsum board
Gypsum board
Gypsum board
Manufacturer
(With Current NOA)
GAF
GAF
GAF
GAF
GAF
GAF
GAF
GAF
GAF
Blue Ridge Fiberboard, Inc.
United States Gypsum Corp.
United States Gypsum Corp.
Georgia-Pacific
Georgia-Pacific
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11101/18
Page 5 of 67
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
(With Current NOA)
1.
Drill -Tee' #12 Fastener
Phillips head, modified
#12 x 8"
GAF
buttress thread, pinch
Max. Length
point, carbon steel fastener
43 Phillips
for use in steel or wood
head.
decks. With CR-10
coating. Available with a
pinch point or drill point.
2.
Drill-Tec' #14 Fastener
Truss head, self -drilling,
#14 x 16"
GAF
pinch point, high thread
Max. Length
fastener for use in steel,
#3 Phillips
wood or concrete decks.
head.
3.
Drill-Tec " XHD Fastener
Truss head, self -drilling,
#15 x 16"
GAF
pinch point, high thread
Max. Length
fastener for use in wood or
#3 Phillips
steel decks. Carbon steel
head.
extra heavy duty fastener
used in steel decks.
4.
Drill-Tec'°' 3" Steel Plate
Round Galvalume® steel
3" Round
GAF
stress plate with
reinforcing ribs and
recessed for use with Drill -
Tee' fasteners.
5.
Drill-Tec' 3" Standard
Galvalume® coated steel
3" Round
GAF
Steel Plate
stress plate for use with
approved Drill-Tec'
fasteners.
6.
Drill-Tec' ASAP 3S
Drill-Tec' #12 fastener
#12 x 8"
GAF
with Drill-Tec' 3"
Max. Length
Standard Steel Plate.
#3 Phillips
head with 3"
Round plate
7.
Drill-Tec' AccuTrac®Flat
A2-SS aluminized steel
3" square;
GAF
Plate
plate for use with Drill-
.017" thick
Tee' fasteners.
8.
Drill-Tec" AccuTrac®
Galvalume® steel plate
3" square;
GAF
Recessed Plate
with recess for use with
.017" thick.
Drill -Tee' fasteners.
9.
Drill-Tec' 3 in. Ribbed
Round Galvalume® plated
3" Round
GAF
Galvalume Plate (Flat)
steel stress plate with
reinforcing ribs for use
with Drill-Tei:7 fasteners.
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 6 of 67
EVIDENCE SUBMITTED:
Test Agency Test Identifier Description Date
FM Approvals
3001276
FMRC 4470
01/28/99
3010215
FMRC 4470
03/01/01
3029832
FMRC 4470
05/11/07
3036980
FMRC 4470
08/14/09
3034312
FMRC 4470
04/09/09
3040738
FMRC 4470
05/18/12
3042887
FMRC 4470
11/14/11
3046081
FMRC 4470
02/13/13
3043633
FMRC 4470
01/20/12
1B9A8.AM
FMRC 4470
09/04/97
3139QLAM
FMRC 4470
01/08/08
3D4Q2.AM
FMRC 4470
04/30/97
ODIA8.AM
FMRC 4470
04/01/98
797-03221-267
FMRC 4470
09/24/07
797-10228-267
FMRC 4470
01/15/15
797-04694-267
FMRC 4470
06/17/09
797-03825-267
FMRC 4470
07/14/08
RR203450
FMRC 4470
12/04/15
FM Letter
FMRC 4470
04/11/13
FM Letter
FMRC 4470
09/15/15
UL LLC
R1306
UL 790
08/21/18
IRT-ARCON Inc.
02-005
TAS 114-J
07/19/04
02-014
TAS 114-J
04/08/02
Trinity I ERD
C8500SCA 1.07
ASTM D6862
11/30/07
G30250.02.10-2
ASTM D6222
11/11/10
G30250.02.10-3-R2
ASTM D3909
06/03/15
G31360.03.10
ASTM D6164
03/31/10
G32520.06.11
ASTM D1876
06/28/11
G33470.01.11
ASTM D6164
01/13/11
034140.04.11-2
ASTM D6163
04/25/11
G34140.04.114-R2
ASTM D4601
6/4/2015
G34140.04.11-5-113
ASTM D4897
6/4/2015
G36780.07.11-R1
TAS 114-J
07/18/11
G40620.07.12-2
ASTM D6222
07/17/12
G40630.01.14-I
ASTM D6163
01/06/14
G40630.01.14-2A
ASTM D5147
01/07/14
G40630.01.14-2A-1-RI
ASTM D6164
04/10/14
G40630.01.14-2B-Rl
ASTM D6164
01/16/15
G40630.01.14-2C
ASTM D6164
01/07/14
G40630.03.14
ASTM D5147
03/06/14
G43190.03.14-1
ASTM D5147
03/06/14
G43190.03.14-2
ASTM D5147
03/06/14
G43190.05.14-R1
ASTM D5147
05/20/14
G43610.01.14
ASTM D5147
01/22/14
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/O1/18
Page 7 of 67
EVIDENCE SUBMITTED: (CONTINUED)
Test Agency
Test Identifier
Description
Date
Trinity ERD
G43190.11.13-1
ASTM D6222
11/15/13
G46160.02.15
ASTM D6163
02/12/15
G46160.02.15-2D-1
ASTM D6163
02/09/16
046160.03.15
ASTM D6163
03/11/15
G46160.09.14-2A
ASTM D5147
09/09/14
G46160.09.14-3A
ASTM D6164
09/09/14
G46160.09.14-3B
ASTM D6164
09/09/14
G46160.09.14-3C
ASTM D5147
09/09/14
G46160.12.14-3E
ASTM D6164
12/29/14
G6850.08.08
ASTM D6163
08/01/08
G6850.08.08-R1
ASTM D6164
04/14/11
G6850.10.08
ASTM D6222
10/06/08
G6850.11.08
ASTM D6222
02/17/09
SC6870.08.14-RI
ASTM D3909
09/04/14
PRI Construction Materials
GAF-122-02-01
TAS 139
05/07/06
Technologies, LLC
GAF-245-02-01
ASTM D6083
06/10/10
GAF-276-02-0 I Rev
ASTME2178
01/04/11
ASTM D6083
GAF-306-02-01
ASTM E96
07/07/11
GAF-314-02-01
ASTM D2178
08/23/11
GAF-315-02-01
ASTM D2178
08/23/11
GAF-369-02-01
ASTM C1289
10/22/12
GAF-434-02-03
TAS 114-J
09/06/13
GAF-434-02-04
TAS 114-J
09/06/13
GAF-464-02-01
ASTM C1289
02/06/14
GAF-498-02-01
ASTM D6083
09/16/16
GAF-499-02-01
ASTM D6083
03/12/14
GAF-500-02-01
ASTM D6083
03/12/14
GAF-559-02-01
TAS 117(B)
09/30/14
GAF-559-02-04
ASTM D1876
10/01/14
GAF-559-02-05
ASTM D1876
10/15/14
GAF-559-02-06
TAS 114(H)
10/02/14
GAF-559-02-07
ASTM D903
10/02/14
GAF-559-02-08
ASTM D903
10/02/14
GAF-559-02-09
ASTM D903
10/02/14
GAF-559-02-11
TAS 114-J
10/14/14
GAF-559-02-12
TAS 114-J
10/14/14
GAF-559-02-13
TAS 114-J
10/15/14
GAF-559-02-14
TAS 114-J
10/15/14
GAF-559-02-15
TAS 114-J
10/15/14
GAF-559-02-16
TAS 114-J
10/15/14
GAF-559-02-18
TAS 114-J
10/15/14
GAF-559-02-19
TAS 114-J
04/16/15
Dynatech Engineering Corporation
#4482.02.95-1
TAS 114-C
09/01/95
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 8 of 67
Membrane Type: APP/SBS Heat Weld
Deck Type 1: Wood, Non -insulated
Deck Description: Min. 19/32" or greater plywood or wood plank secured 6 in. o.c. with 8d ring
shank nails to supports spaced 24 in. o.c. max.
System Type E(2): Anchor sheet is mechanically attached to roof deck. (Non -insulated systems)
All General and System Limitations shall apply.
Fire Barrier: FireOut " Fire Barrier Coating, VersaShield® Fire -Resistant Roof Deck
(optional) Protection, VersaShield® Solo' Fire -Resistant Slip Sheet, DensDeck®Roof
Board, SECUROCK® Gypsum -Fiber Roof Board or SECUROCK® Glass -Mat
Roof Board.
Base sheet: GAFGLAS® 480 Ultima"' Base Sheet, GAFGLAS® Stratavent® Nailable Venting
Base Sheet, Ruberoid® Mop Smooth, Ruberoid® Mop Smooth 1.5, Ruberoid®
Mop Plus Smooth, Ruberoid® 20 Smooth, Ruberoid® HW Smooth or Ruberoid®
HW 25 Smooth mechanically fastened to deck as described below;
Fasten)#1:
GAFGLAS® Ply 4, Tri-Ply® Ply 4 Ply Sheet, GAFGLAS® FlexPly"" 6,
OptioGAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet or any of above base
sheets attached to deck with approved annular ring shank nails and tin caps at a
fastener spacing of 9" o.c. at the lap staggered and in two rows 18" o.c. in the
field.
Not for use with DensDeck or SECUROCK Fire Barrier
(Maximum Design Pressure -45 psf. See General Limitation #9)
Fastening GAFGLAS® Ply 4, Tri-Ply® Ply 4 Ply Sheet, GAFGLAS FlexPly' 6,
Option #2: GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet or any of above base
sheets attached to deck with Drill-Tec'" #12 Fastener or Drill-Tec' #14 Fastener
and Drill-Tec' 3" Steel Plate, Drill-Tec' AccuTrac® Flat Plate or Drill -Tee
AccuTrac® Recessed Plate installed 12" o.c. in 3 rows. One row is in the 2" side
lap. The other rows are equally spaced approximately 12.5" o.c. in the field of
the sheet.
(Maximum Design Pressure -45 psf. See General Limitation #9)
Fastening GAFGLAS® FlexPly'" 6, GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet
Option 93: or any of above base sheets attached to deck with approved annular ring shank
nails and tin caps at a fastener spacing of 9" o.c. at the 4" lap staggered and in
two rows 9" o.c. in the field.
Not for use with DensDeck or SECUROCK Fire Barrier
(Maximum Design Pressure —52.5 psf. See General Limitation #7)
Fastening GAFGLAS® 975 Base Sheet, Tri-Ply® #75 Base Sheet or any of above base
Option #4: sheets attached to deck with Drill-Tec"" #12 Fastener or Drill -Tee' #14 Fastener
and Drill -Tee' 3" Steel Plate, Drill-Tec"" AccuTrac® Flat Plate or Drill-Tec""
AccuTrac® Recessed Plate installed 12" o.c. in 4 rows. One row is in the 2" side
lap. The other rows are equally spaced approximately 9" o.c. in the field of the
sheet.
(Maximum Design Pressure —45 psf. See General Limitation #9)
NOA No.: 18-0919.12
MIAMIDADECOUNTY Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 53 of 67
Fastening GAFGLAS' #80 Ultima" Base Sheet, Ruberoid® 20 Smooth, Ruberoid®Mop
Option #5: Smooth base sheet attached to deck approved annular ring shank nails and 3"
inverted Drill-Tec"' 3" Steel Plate at a fastener spacing of 9" o.c. at the 4" lap
staggered in two rows 9" in the field.
Not for use with DensDeck or SECUROCK Fire Barrier
(Maximum Design Pressure —60 psf. See Genera! Limitation #7)
Fastening GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet or any of above base
Option #6: sheets attached to deck with Drill-Tec' # 12 Fastener, Drill-Tec' # 14 Fastener or
Drill-Tec"' XHD Fastener and Drill-Tec"' 3" Steel Plate, Drill-Tec' AccuTrac'
Flat Plate or Drill-Tec' AccuTrac' Recessed Plate installed 8" o.c. in 4 rows.
One row is in the 2" side lap. The other rows are equally spaced approximately
9" o.c. in the field of the sheet.
(Maximum Design Pressure f15 psf. See Genera! Limitation #9)
Ply Sheet: (Optional except over Ruberoid® Mop Smooth, Ruberoid® Mop Smooth 1.5,
Ruberoid® Mop Plus Smooth, Ruberoid® 20 Smooth, Ruberoid® HW Smooth or
Ruberoid® HW 25 Smooth) One or more plies GAFGLAS® Ply 4, Tri-Ply® Ply 4,
or GAFGLAS® FlexPly 6 sheet adhered in a full mopping of approved asphalt
applied within the EVT range and at a rate of 20-40 lbs./sq. or Ruberoid® Torch
Smooth torch applied according to manufacturer's application instructions.
Membrane: One ply of Ruberoid® Torch Smooth, Tri-Ply® APP Smooth Membrane,
Ruberoid®Torch Granule, Tri-Ply® APP Granule Cap Sheet, , Ruberoid®
EnergyCap' Torch Granule FR, Ruberoid® EnergyCap' Torch Plus Granule FR,
or Ruberoid® Torch Plus Granule FR torch applied according to manufacturer's
application instructions.
Or
One or more plies of Ruberoid® HW Plus Granule, Ruberoid® HW Plus Granule
FR, Ruberoid® HW Granule FR, Ruberoid® EnergyCap"' HW Plus Granule FR,
Ruberoid® HW Granule, Ruberoid® HW Smooth and Ruberoid® HW 25 Smooth
applied according to manufacturer's application instructions.
Surfacing: Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat
of Approved asphalt at 60 lbs./sq.
2. GAFGLAS' Mineral -Surfaced Cap Sheet, Tri-Ply' BUR Granule Cap Sheet
or GAFGLAS'EnergyCap"' Mineral -Surfaced Cap Sheet adhered in a full
mopping of approved asphalt applied within the EVT range and at a rate of 2040
lbs./sq.
3. TOPCOAT' Surface Seal SB or United Coatings' Surface Seal SB Roof Coating
applied in one or more coats at a minimum rate of 1.0 gal./sq. per coat.
OR
TOPCOAT' MB Plus or United Coatings"" Roof Mate MB Plus Coating
applied at a minimum rate of 1.0 gal./sq.(to be used as a primer) followed by
TOPCOAT' Membrane or United Coatings' Roof Mate TCM Coating
applied in one or more coats at a minimum rate of 1.0 gal./sq. per coat.
4. Fiber Aluminum Roof Coating.
Maximum Design
Pressure: See Fastening Options
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 54 of 67
WOOD DECK SYSTEM LIMITATIONS:
I A slip sheet is required with GAFGLAS® Ply 4 and GAFGLAS® FlexPly' 6 when used as a
mechanically fastened base or anchor sheet.
2. Minimum'/a" DensDeck® Roof Board or %2" Type X gypsum board is acceptable to be installed
directly over the wood deck.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials
Directory for fire ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with
Product Control Approval guidelines. All other layers shall be adhered in a full mopping of
approved asphalt applied within the EVT range and at a rate of 20-401bs./sq., or mechanically
attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved
asphalt, panel size shall be Tx 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell
foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet
shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip
mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing
a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be
placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall
be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum
design pressure of -45 psE
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of
275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value,
as field-tested, are below 275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based
on a minimum fastener resistance value in conjunction with the maximum design value listed within
a specific system. Should the fastener resistance be less than that required, as determined by the
Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida Registered
Engineer, Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing
shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and
calculations in compliance with Roofing Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these
areas. Fastener densities shall be increased for both insulation and base sheet as calculated in
compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed
by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant
(When this limitation is specifically referred within this NOA, General Limitation #9 will not
be applicable.)
8. All attachment and sizing of perimeter milers, metal profile, and/or flashing termination designs
shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e.
field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for
enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners).
(When this limitation is specifically referred within this NOA, General Limitation #7 will not
be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida
Building Code and Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 18-0919.12
Expiration Date: 11/06/23
Approval Date: 11/01/18
Page 67 of 67