HomeMy WebLinkAboutEVALUATION REPORTouAWNED
BY
„nrllnT3ln1 ccor,tzs '-it Lucie Com
East Coast Metals, Inc.
2301 West 8 Lane
Hialeah, FL33010
EXTI ERIOR RESEARCH & DESIGN, LLC.
Candficate of Autimreption -9503
353 CHRISTIAN STREW, UNIT #13
OXFORD, CT 06478
PHONE: (203) 262-9245
FAX: (203) 262-9243
main rcepuie
F1537n-R4
Date of Issuance: 0910312008
Revision 4: 03117/2015
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P-E. for
use of the product under the Florida Building Code and Florida Building Code, Residential Volume_ The products described
ha_min nave been evaluated for compliance with the 5un Edition (201=) Florida Building Code sections noted herein.
DESCRIPTION: East Coast Metals Channel Metals
LABEDNC: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CORm uED ComPuwvi cE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
t constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the
Evaluation Report by the named clien
referenced Quality Assurance documentation changes. Trinity) ERD requires a complete review of this Evaluation Report
relative to updated Code requirement with each Code Cycle.
P:oveRTls=MEiti: The Evaluation Report number preceded by the words 'Trinitq(ERD Evaluated" may be displayed in
advertising lit--rature. If any portion of the Evaluation Report Is displayed, then it shall be done in it entirety.
Io-IsPEcTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or it
distributors and shall be available for inspection atthe job site at the request of the Building Official.
This Evaluation Report consists of pages !through 7.
Prepared by:
Rohe,:!.,. Nieminen, P.E.
Fiodou Registration No. 59166, Floddc OCA A,PL4'1983
Y.-.ci:¢oalxzealapPzzriadt =z aY.:am=d tt a==en::i^Liven.
P.e. on zrz/Iir'-DJA iM1C L-scnmzen: s=ndc^..�::�aVYzi3'zd
mmmenL pd ed.ecled Yvruce?ixs4aze Exen:ramG:[na:o:b
PmdunAppmvallulmNe:r:� a:.d:o Mc namxi c+cc:
CERTIFICS11ON OF INDEPENDEPIM
1, Trinib,•I ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity[ ERD is not owned, opera' ad or controlled by any company manufacturing or distributing products itevaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued. rpcss of the
s. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approvalP
product.
S. This is a building code evaluation. Neither Trinity(ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, islwas used for permitting or design guidance unless retained
snecifi :ally for that purpose.
TRINITY I ERD
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Roofing Accessories that are an Integral Part of the Roofing System
Compliance Statement: East Coast Metals Channel Metals, as produced by East Coast Metals, have demonstrated compliance
with the following sections of the Florida Building Code through testing in accordance with the following Standards. Compliance
is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section
Property
Standard
Year
1507.3.7
Installation, non-HVHZ
FRSA/rRI April 2012 (04-12)
2012
1518.8.1
Installation, HVHZ
RAS 118,119 & 120
1995
1523.6.5.2.2
Static Uplift Resistance
TAS 101
1995
1711.2.1
Static Uplift Resistance
SEW SSTD 11
1997
3. REFERENCES:
gBiLty.
Examination
Reference
Date
ERD (TST6049)
Static Uplift Resistance
E42730.08.13
08/23/2013
ERD (TST6049)
Static Uplift Resistance
ECM-SC6795.12.14-1
02/27/2015
ERD(TST6049)
Static Uplift Resistance
ECM-SC6795.12.14-2
02/27/2025
Florida TEC (TST7393)
TAS 101
SIG-02SR
10/27/2010
PRI (fST5878)
TAS 101
ECM-001-02-01
09/21/2001
PRI (TST5878)
TAS 101
ECM-003-02-01
06/13/2008
PRI (TST5878)
TA5101
ECM-004-02-01
06/13/2008
PRI (TST5878)
TAS 101
ECM-005-02-01
06/13/2008
PRI (TST5878)
TAS 101
ECM-006.02-01
06/13/2008
PRI (TSI5878)
TAS 101
ECM-007-02-01
06/13/2008
PRI DST5878)
TA5301
ECM-008-02-01
06/13/2008
Florida Building Code
Attachment Requirements
FRSA/TRI April 2012 (04-12)
04/2012
Florida Building Code -HVHZ
Attachment Requirements
RAS 218, 119 and 120
1995
East Coast Metals
Metal Quality
Mill Certifications
Various
Architectural Testing(QUA3844)
QualityControl
Participation Letter
Exp. 12/31/2018
4. PRODUCT DESCRIPTION:
4.1 Hip & Ridge Channel Metal: Pre -formed metal channel
designed for use as a hip and ridge base to which roof tiles
are bonded in FBC Approved roof tile adhesive.
Hip & Ridge Channel Metal is available in 119-3/84nch (±
3/8-inch) length by 2.5, 3, 3.5, 4, 5, 6 or 7-inch (±3/8-inch)
heights with 1.5-inch (±1/16-inch) deck -Ranges.
Exterior Research and Design, LLC Evaluation Report E10240.08.08-R4
cerd/hvte ofAuthormanon 09503 FL5374-114
- - - - - -- � -- - - - — - - _ - - Revision 4: 03/17/2015
Page 2 of 7
= j ' 1, a t� 1_RD
4.2 Trim Lock Channel Metal: Pre -farmed metal charm
designed for use as a hip and ridge base to which roof ti s
are banded in FBC Approved roof the adhesive. Trifail,
ck
Channel Metal is characterized by its Prot"dad
perforated upper horizontal flange designed to re
and allow for interlock with the overlyingthe adhesi
Trim Lock Channel Metal is available in 119-3/8-Inch (+
3/8") length by 3, 3.5, 41 5 or 6-inch (_ 3/8-inch) eights
with 1.5-inch (r 1/16-inch) deck -flanges.
4.2 Trim Lock Plus Channel Metal: Preformed metal channel
designed for use as a hip and ridge base to which roof tiles
are bonded in FBC Approved roof file adhesive. Trim Lock
Plus Channel Metal is characterized by its profiled and
perforated upper horizontal flange designed to receive
and allow for interlock with the overlying file adhesive
and its perforated deck flanges, designed for installation
atop the roof underlayment via placement in FBC
Approved roof We adhesive, which flows -through and
interlocks with the undedyingadhesive.
Trim Lock Plus Channel P4etal is available in 11-n-3/84nch
(±- 3/8") length by 3, 3.5, 4, 5 or 6-inch (-3/8-inch) heights
:vith 1.5-inch (_1/16-inch) deck,langes.
4.4 East Coast Metals Channel Metals are fabricated of the following metals:
> Galvanized Steel: Min. 0.019 + 0.002-inch, ASTM A653 (G-90), min. 33 KSL
> Galvalume Steel: Min. 0,019=0.002-inch, ASTM A792, AZ55, min. 35 KSI.
> Aluminum: ivlin. 0.032_ 0.002-inch, ASTM B209, 3003-1-114, min. 21 KSI.
y Stainless Steel: Min. 0.019=0.002-inch, ASTM A240/A480, T304, min. 35 K51.
5. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinitVI ERD nor Robert Nieminen, P.E. are, in any way, the Designer of
Record for any project an which this Evaluation Report, or previous versions thereof, is/eras used for permitting or
design guidance unless retained specifically for that purpose.
exterior Research and Design, LLC. Evaluation Report E10240.08.08-114
Certircute OfAuthorizodon 05a3 FI
Revision 4: 03/17/2024
17/20_5
page of 7
TRINITV I ERD
5.2 FOR HVHZJURISDICnONS:
5.21 For Hip & Ridge Channel Metal or Trim Lock Channel Metal, refer to FBC RAS 118, Drawing 13, Detail 3; RAS 119,
Drawing 12, Detail 3; or RAS 120, Drawing 15, Detail 3. For Trim Lock Plus Channel Metal, refer to the installation
instructions herein.
5.2.2 For HVHZ jurisdictions, installations of Hip & Ridge Channel Metal and Trim Lock are prescriptive by RAS 118, 119 and
120, and the data in Tables 1A and 1B is supplemental to these prescriptive allowances.
Installations of Trim Lock Plus are limited to projects having a required moment resistance (Mr) or uplift resistance (F,),
as determined in accordance with RAS 227, not greaterthan the following values.
Refer to the tile adhesive manufacturers published installation instructions for adhesive paddy placement details.
➢ "INDEPENDENT" paddy placement means each individual tile is bonded to the Channel Metal in its own, single
foam paddy; tile head laps are not bonded. This method is limited to 2-part tile adhesives. Allowable
performance data below for "INDEPENDENT" paddy placement already has a 2 to 1 margin of safety applied to
ultimate performance.
➢ "INTERDEPENDENT" paddy placement means each individual the is bonded to the Channel Metal in a foam paddy,
and a second foam paddy bonds the file head lap, or two tiles are bonded to the Channel Metal using a single
foam paddy. Allowable performance data below for "INTERDEPENDENT" paddy placement already has a 4 to 1
margin of safety applied to ultimate performance.
" r .TABLE lk. PEpfORMAN[E LIMRATONs-'HVHZ, INDEPENOENLPADDYPIACEMENf
.: �. .. . : ..(2701MANGINOFSgFF/YAIFFADYAP➢IIEDI
Hip/Ridge Metal
Tile
Adhesive
Allowable Performance
Design
Metal Type
Type
Placement
Moment Based
Uplift Based
M,(ft-lbf)
F'(Ibf)
Hip & Ridge
galvanized
clay or
3M'" 2-Component Foam
Independent
127
169
Channel Metal
concrete
Roof Tile Adhesive AH-160
Trim Lock
galvanized, Galvalume°,
clay or
3M"'2-Component Foam
Independent
171
159
aluminum or stainless steel
concrete
Roof Tile Adhesive AH-160
Trim Lock Plus
galvanized, Galvalume®,
dayor
3M"'2-Component Foam
Independent
177
165
aluminum or stainless steel
concrete
Roof Tile Adhesive AH-160
- TABLEIB: PERFDRMANCELIMRAMONS-HVHZ,INTiflio P D-ENTPADDYPLACEMENT-
. .' f4Tp3MARGINOF5 FR1'AMEF DYAPYUEDJ
Hip/Ridge Metal
Tile
Adhesive
Allowable Performance
Design
g
MetalT a
Type
T ype
Placement
Moment Based
Uplift Based
Mr(ft-Ibf)
F'(Ibt)
Trim Lock or Trim
galvanized, Galvalumem,
dayor
3M"' 2-Component foam
Lock Plus
aluminum or stainless steel
concrete
Roof Tile Adhesive AH-160
Interdependent
95
88
Trim Lock
galvanized, Galvalume•,
clay or
3M- Roof Tile Adhesive
Interdependent
99
94
stainless steel
concrete
RTA-1
Trim Lock
aluminum
clay or
3M" Foam Roof Tile
Interdependent
90
84
concrete
Adhesive RTA-1
Trim Lock Plus
galvanized, Galvalume®,
clay or
3M'" Foam Roof Tile
Interdependent
90
84
aluminum or stainless steel
concrete
Adhesive RTA-1
Trim Lock
galvanized, Galvalume° or
day or
TILE BOND^' Roof Tile
Interdependent
123
117
stainless steel
concrete
Adhesive
Trim Lock
aluminum
day or
TILE BOND - Roof Tile
Interdependent
79
73
concrete
Adhesive
Trim Lock Plus
galvanized, Galvalume°,
day or
TILE BOND"' Roof Tile
Interdependent
79
73
aluminum or stainless steel
concrete
Adhesive
Trim Lock
galvanized, Galvalume• or
day or
TDuch'n Seal StormBond
Interdependent
146
139
stainless steel
concrete
Roof Tile Adhesive
Trim Lock
Aluminum
day or
Touch'n Seal StormBond
Interdependent
58
54
concrete
Roof Tile Adhesive
Trim Lock Plus
galvanized, Galvalume®,
clay or
Touch'n Seal StormBond
Interdependent
58
54
aluminum or stainless steel
concrete
Roof Tile Adhesive
Exterior Research and Design, LLG Evaluation Report E3D240.08.08-R4
CertifcoteofAuthonzatrona9503 FL5374-R4
Revision 4:03/17/2015
Page 4 of 7
q -- jp Fifth./
�yi� ojSl n 1
5.3 FOR NON-HVHZJURISDICTIONS•
5.3.1 For Hip E Ridge Channel metal or Trim Lock Channel Metal, refer to FRSA/TRI April 2012 (04-12). For Trim Lock Plus
Channel Metal, rarer to the -installation instructions herein
5.3.2 For non-HVHZ, installations are limited to projects having hip and ridge design pressure requirements, determined in
accordancewith Table 1A of FRSA/TRI April 2012 (04-12), not greater than the following values. Refer to the tile
adhesive manufacturers Published installation instructions for adhesive paddy placement details.
"INDEPENDENT" paddy placement means each individual the is bonded to the Channel Metal in its own, single
foam paddy; tile head laps are not banded. This method is limited to 2-part tile adhesives. This method is limited
to 2-part tile adhesives. Allowable performance data below for "INDEPENDENT" paddy placement already has a 2
to 1 margin of safety applied to ultimate performance.
`r "INTERDEPENDENT"paddy placement means each individual tile is bonded to the Channel Metal in a foam paddy,
and a second foam paddy bands the tile head lap, or two tiles are bonded to the Channel Metal using a single
foam paddy. Allowable performance data below for "INTERDEPENDENT" paddy placement already has a 4 to 1
margin of safety applied to ultimate performance.
TABLE2A: PERFORMANCELIMrrAMON5—NON-HVHZ,INDEPENDEN7 PADDYPLACEMENT
12 TO 1 MARGIN OFSA�AIRFAOYAPPIIED)
Hip/Ridge Metal
TileHtn
Adhesive
Allowable Uplift
(Psf)
Design Metal T a
�
Type
Placement
&Ridge
Channel Metal (galvanized
day or
3141^'2-Component Foam Roof
Independent
I 169
concrete
Tile AdhesiveAH-150
Trim Lock I galvanized, Galvalumea, aluminum or
clay or
3M"' 2-Component Foam Roof
stainlesssteel
(concrete
I Tile Adhesive AH-160
Independent
173
Trim Leer. Plus galvanized, Galvalumea, aluminum or
day Dr
3M"'2-Component Foam Roof
sinless steel Icpncrete
I
Tile Adhesive AH-160
Independent
178
IABLE2B: PERFORMANCE IIMRATIONS—NON-HVHZ, INTEREIVENDEM PADDY PLACEMENT
(4 To 1 h1ARGIN OFSAF ALJ? A YAPPDED) -
I Hip/Ridge Metal
Tile
Adhesive
Allowable Uplift
(Psf)
Design
PAetal Type
Type
I Placement
Trim Lock or Trim
galvanized, Galvalume', aluminum or
day or
3M'e 2-Component Foam Roof
Loci: Plus
stainless steel
concrete
Tile Adhesive AH-160
Interdependent
98
Trim Lock
I nized, Galvalumea arstainlass
clay or
Foam Roof Tile Adhesive
steel
concrete
13.Vi—
RTA-1
Interdependent
I 110
Trim Lod:
`�
(aluminum
(clay or
3AI- Foam Roof Tile Adhesive
Interdependent
93
concrete
RTA-1
Trim Loci: Plus
,galvanized, Galvalumea, aluminum or
clay or
3NI" Foam Roof Tile Adhesive
stainless steel
Concrete
RTA-1
Interdependent
p
93
Trim Loch
galvanized, Galvalume= or stainless
day or,
I
steel
concre
concrete
(TILE BOND"'Roof Tde Adhesive
Interdependent
TS2
Trim Lock
( aluminum
day or
I TILE BOND'" Roof Tile Adhesive
Interdependent
I 82
concrete
Trim Lock Plus
galvanized, Galvalumea, aluminum or
day or
stainless steel
concrete
TILE BOND- Roof Tile Adhesive
Interdependent I
82
Trim Locklvanized,
Galvalume' orstainless
day or
Touch'n Seal StormBond Roof
steel
concrete
Tile Adhesive
Interdependent
148
Trim Lpcl: I
Aluminum
day or
(Tile
Touch'n Seat StornlBond Roof
Interdependent
61
I
Concrete
Adhesive
Trim Locl: Plus
galvanized, Galualume_�, aluminumor
Dr
TOPch'n Seal StonnBond Roof
(day
stainless steel
concrete I
Tile Adhesive
Interdependent
61
F=Aerior Research and Design, LLC. Evaluation Report E10240.08.08-114
CtrOfonT ofAurhorfzatran 99503 FI5374-114
Revision 4: 03/17/2013
.._ . ..... Page 5 of 7
TRIN11Y ERD
i
6. INSTALLATION:
6.1 The roof deck shall be minimum 15/32-inch plywood (non-HVHZ) or minimum 19/32-inch plywood (HVHZ) attached in
accordance with FBC Chapter 23 to the satisfaction of the AHJ.
6.2 Hip & Ridge Channel Metal and Trim Lock Channel Metal shall be installed using min. it ga. x N-inch long x 3/8-inch
head diameter galvanized annular ring shank nails spaced 6-inch o.c. along both deck -flanges. Fasteners shall be
positioned %-inch from the outside edge of each deck -flange, set in a bed plastic roof cement. For FBC HVHZ, refer to
FBC RAS 118, Drawing 13, Detail 3; RAS 119, Drawing 12, Detail 3; or RAS 120, Drawing 15, Detail 3.
6.3 Trim Lock Plus Channel Metal shall be installed atop the Approved roof underlayment in continuous 2-inch wide ribbons
of tile adhesive centered beneath each 1.5-inch wide deck flange. Place the Trim Lock Plus Channel Metal into the wet
adhesive and allow it to set-up priorto installation of roof tiles.
View of Polyset AH160 Placement for Trim Lock Plus Channel Metal Installation
6.3.1 It is critical that the bond between the Trim Lock Plus Channel Metal, the tile adhesive and the underlayment is not
disturbed prior to or during placement of the ridge tiles.
6.3.2 Approved underlayments are the codified '30/90' system or other FBC Approved roof underlayments listing approved
use of the subject tile adhesive.
Exterior Research and Design, LLC Evaluation Report E10240.08.08-R4
Cerifficam ofAvrhorlration 050 FL5374-114
Revision 4: 03/17/2015
Page 6 of 7
MINI
e s RD
1. �
6.4 Tile shall be installed atop the Channel Metal in accordance with the tile adhesive manufacturer's Approved, published
installation instructions, subject to the limitations outlined in Section 5 herein. The exposed edges shall be packed and
pointed with Approved mortar or weather blocking adhesive in accordance with FRSA/TRI April 2012 (04-12) or RAS
118, RAS 11-0, RAS 120 requirements.
Hip / Ridge Tile
Tile Adhesive
Trim Lock Plus
Moltar or Weather Block
Adhesive
Tile Adhesive
View of Trim Lock Pius Channel Metal Installation after Weather Blocked
6.4.1 Channel Metal shall be free w dust, debris, ails or other bond -breaking substance priorto placement of adhesive.
BUILDING PERMIT REQUIREMENTS:
As required bythe Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.
S. MANUFAC, URING PLANTS:
Contact the named CA entity for manufacturing facilities covered by F.A.C. Rule 61620-3 QA requirements.
9. QUALITY ASSURANCE ENTITY:
Architectural Testing, Inc—QUA1W, (717) 764-7700
-END OF EVALUATION REPORT -
Ettertar Research and Design, LLG Evaluation Report E10240.08.08-R4
Cerrifm[e aJAurhariraron A9505 FL5374-R4
Revlsian 4: 03/17/2015
Page 7 of 7
TRINITY ERD
P. N 1 EGRA
RO O F T I L E
SCOPE:
SUANNED
BY
St. Lurie County
Entegra Roof Tile, LLC
1289 NE 9`s Avenue
Okeechobee,FL34972
(602)515-6933
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT 1113
OXFORD, CT 06478
(203)262-9245
FL7804-R10
Date of Issuance:11/02/2011
Revision 4:10/17/2017
This Evaluation Report is issued under Rule 61GZO-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the a Edition (2017) Florida Building Code
(HVHZ) sections noted herein.
DESCRIPTION: Entegra Concrete Roof Tiles (HVHZ jurisdictions)
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinityiERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by:
Robertl.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DUI ANE1983
The raminige seat appearingms authadzed by Robert Nleminen,
P.E. on 10117/2017. ,,does ne,,eme as an elenronl<altysigned
doendent. Signed, sealed hardwpies have been transmitted to the
Pmdud Approval Adednistrato, nd to the named dent
CERTIFICATION OF INDEPENDENCE:
1. Trinityl ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity) ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
ti l
TRINITY ERD
ROOFING SYSTEM EVALUATION:
1. SCOPE:
Product Category:
Roofing
Sub -Category:
Roofing Tiles
Compliance Statement:
Entegra Concrete Roof Tiles, as
produced by Entegra Roof Tile, L-C, have demonstrated
compliance with the following sections of the Florida Building
Code through testing
in accordance with the following
Standards. Compliance
is subject to the Installation Requirements
and Limitations
/ Conditions of Use set forth
herein.
2. STANDARDS:
Section
Pro a
Standard
Year
1523.6.5.2
Physical Properties
TAS 112
1995
1523.6.5.2
Wind Driven Rain
TAS 100
1995
1523.6.5.2.2
Static Uplift Resistance
TAS 101
1995
1523.6.5.2.3
Static Uplift Resistance
TAS 102
1995
1523.6.5.2.3
Static Uplift Resistance
TAS 302(A)
1995
3. REFERENCES:
Entity
Examination
Reference
Date
ERD (TST6049)
TAS 101
P39740.02.12
02/21/2012
ATL(TST3782)
Physical Properties
RT0624.05-14
07/03/2014
ATL(TST3782)
Physical Properties
RT0624.04-14
07/07/2014
ATL(TST3782)
Physical Properties
RT1210.02-15
12/17/2015
ATL(TST3782)
Physical Properties
RT1210.03-15
12/17/2015
ATL (TST 3782)
Physical Properties
RT1103.01-15
11/07/2015
ATL (TST 3782)
Physical Properties
RT3103.02-15
11/07/2015
ATL (TST 3782)
Physical Properties
RT1103.03-15
11/07/2015
ATL (TST 3782)
Physical Properties
RT1103.04-15
11/07/2015
ATL (TST 3782)
Physical Properties
RT1103.05-15
11/07/2015
Miami -Dade (CER1592)
HVHZ Compliance
14-0416.12
11/27/2014
Miami-Dade(CER1592)
HVHZ Compliance
15-0721.04
11/05/2015
Miami-Dade(CER1592)
HVHZCompliance
16-0112.06
02/25/2016
Miami-Dade(CER1592)
HVHZ Compliance
16-0112.07
02/25/2016
Miami-Dade(CER1592)
HVHZ Compliance
16-0112.08
02/25/2016
Tile Roof Institute
TAS 100, TAS 101, 102, 102(A)
Membership Confirmation
Current
PRI (QUA9110)
QualityAssurance
Service Confirmation
Exp. 11/02/2018
Exterior Research and Design, LLC.
Evaluation Report E39310.31.11-1-R4
Certiflcute ofAuthorfcotlnn 095M
OTM EDITION(2017) FBC HVHZ EVALUATION
FL7804•R70
Entegra Roof Tiles
Revision 4:10/17/2017
Page 2 of 8
C!
` 3. TRINITY . ERD
PRODUCT DESCRIPTION:
4.1 TASu2 Type3a (flat -profile) BERMum FLAT, PuwTAMONFIAT ai
r
16'
30'\ / kPlantatlon
716'-10,
Bermuda Fiat
17-1/4"
13"
Horizon Flat
FLAT
Evaluation Report E39310.11.31-1-R4
Exterior Research and Design, LLG FL7804-R10
certipcate ofAuthonzadon Mat 61e EDITION(2017) FBC HVHZ EVALUATION Revision 4: 10/17/2017
Entegra Roof Tiles Page 3 of 8
4.2 I TAS 312; Type la (interlocking, high -profile)
4.3 -.TAS 112, Typeab
Holes —��
4.3
17"
Estate "S"
Galena Spanish "S"
Bella High "5"
rlow-profile)
10"
TRINITY � ERD
ESTATE "S" and HACIENDA
Hacienda
GALENASPANISH "S" and REGAL
Exterior Research and Design, U.C. Evacuation Report E39310.11.11-1-R4
CertrRmte of Authoritarian A9503 6' EDITION(2017) FBC HVHZ EVALUATION FL7804-R10
Entegra Roof Tiles Revision 4:10/17/2017
Page 4 of 8
<` TRINITY ERD
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is for use in FBC HVHZjurisdic'tions or others adopting FBC HVHZ requirements.
5.3 Fire classification is not part of this evaluation; refer to FBC 1516 or listing by an approved testing agency for
fire rating of this product.
5.4 Reference is made to FBC 1512.4.2.4 regarding field testing of completed tile roof installations.
5.5 Applicant shall retain the services of an FBC listed, accredited laboratory to perform quarterly tests in
accordance with TAS 112, Appendix'A'.
5.6 Minimum underlayment shall comply with the RAS 128, RAS 119 or RAS 120, as applicable. Underlayment
products shall hold current Florida Statewide Product Approval or Local Approval for use in tile roof
assemblies in FBC HVHZ jurisdictions.
5.7 Minimum roof deck requirements shall be in accordance with applicable FBC HVHZ requirements.
5.8 All products in the roof assembly shall have quality assurance audit in accordance with the F.A.C. Rule
61G20-3.
6. INSTALLATION:
6.1 Entegra Concrete Roof Tiles may be mechanically fastened, mortar -set or adhesive -set. Installation shall
comply with manufacturer's current published instructions, but not less than the requirements of RAS 118,
RAS 119 or RAS 120, as applicable.
6.2 Attachment Calculations: Entegra Concrete Roof Tile shall be evaluated as a 'Moment -Based System' in
romance Vvith Rnnfinp Annlication Standard RAS 127-11 using the data outlined herein.
TABLE I: AERODYNAMIC MULTIPLIERS -%(FT) - -
Tile
Batten Application
Direct -Deck Application
Bermuda Flat
0.189
0.205
Plantation Flat
0.267
0.289
Horizon Flat
0.305
0.330
Bella High "S"
0.349
0.378
Estate "5"
0.267
0.289
Hacienda
0.267
0.289
Galena Spanish "5"
N/A
0.235
Regal
0.287
0.311
\3
TABLE 2: RESTORING MOMENT DUE TO GRAVITY-M�
Roof Slope (0)
Tile
2:124043:12
3:12<0<4:12
4:12<0<5:12
5:12<0<6:12
6:1240<7:12
027:12
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Bermuda Flat
5.22
6.43
5.17
6.37
5.09
6.27
4.98
6.15
4.86
6.00
4.72
5.83
Plantation Flat
7.22
7.91
6.85
7.79
6.75
7.67
6.61
7.52
6.44
7.32
6.26
7.04
Horizon
7.60
8.32
7.52
8.24
7.41
8.12
7.26
7.95
7.09
7.76
6.89
7.55
Bella High "5"
Estate "S"
6.19
6.14
6.89
6.84
6.11
5.91
6.80
6.74
5.99
5.82
6.67
6.64
5.85
5.70
6.51
6.50
5.68
5.56
6.33
6.33
5.50
5.40
6.13
6.14
Hacienda
5.92
6.80
5.92
6.80
5.82
6:69
5.70
16.55
5.56
6.39
5.41
6.22
Galena Spanish "S"
Regal
N/A
7.77
6.20
8.34
N/A
7.77
6.13
8.34
N/A
7.65
6.03
1 8.20
N/A
1 7.49
5.89
1 8.03
N/A
7.30
5.74
7.83
N/A
7.10
5.57
7.61
Exterior Research and Design, U.C.
CWijrcote ofAuthorl:ation 09509 6n'EDITION(2017) FBC HVHZ EVALUATION
Entegra Roof Tiles
Evaluation Report E39310.11.11-1-R4
FL7804-R10
Revision 4:10/17/2017
Page 5 of 8
TRINITY' ERD
TABLE 3A: ATTACHMENT RESISTANCE- EXPRESSED AS A MOMENT -MF(Ff-LBF)
_MECHANICALLYATTA[HEDSYSTEMS '
Tile
Fastener
Direct -Deck
(min. 15/32-
plywood)
Direct -Deck
(min. 19/32"
plywood)
Battens
T e
YP
g
Size
Shank
Clip
p
Nail
One (1)
10d
Smooth or Screw
N/A
7.3
9.8
4.9
Nail
Two (2)
10d
Smooth or Screw
N/A
14.0
18.8
7.4
Nail
One (1)
10d
Smooth or Screw
Eave
19.0
19.0
22.1
Nail
One (1)
SOd
Smooth or Screw
Field
24.3
24.3
24.2
Bermuda Flat,
Nail
Two (2)
30d
Smooth or Screw
Eave
31.9
31.9
32.2
Plantation Fiat or
Nail
Two (2)
10d
Smooth or Screw
Field
35.5
35.5
34.8
Horizon
Nail
Two (2)
lOd
Ring
N/A
30.9
38.1
17.2
Nail'
Two (2)'
10d'
Ring'
N/A
50.3'
65.5,
48.3'
Screw
One (1)
88
N/A
N/A
30.8
3D.8
18.2
Screw
Two (2)
88
N/A
N/A
51.7
51.7
24.4
'Installation with a 4-Inch tile headlap and fasteners located min. 2%-inch from head of tile.
Nail
One
10d
Smooth or Screw
N/A
8.82
11.8'
4.1'
Nail
Two (2)
10d
Smooth or Screw
N/A
16.4
21.9
7.1
Nail
One (1)'
10d
Smooth or Screw
Eave
19.02
19.02
22.12
Nail
One(111
10d
Smooth or Screw
Field
24.3'
24.32
24.2'
Nail
Two (2)
10d
Smooth or Screw
Eave
31.9
31.9
32.2
Estate "5" or HaciendaNail
Two (2)
10d
Smooth or Screw
Field
35.5
35.5
34.8
Nail
Two (2)
10d
Ring
N/A
27.8
37.4
28.8
Nail'
Two(21'
10d'
Ring'
N/A
43,0'
67.5'
50.9'
Screw
One
g8
N/A
N/A
25.82
25.82
22.9'
Screw
Two (2)
g8
N/A
N/A
47.1
47.1
49.1
'Installation with a 4-Inch the headlap and fasteners located min. 2Y-Inch from head of tile.
' For one (1) fastener Installations, utilize hole that is approximately 4X-inch from the Interlocking edge.
Nail
One (1)
10d
Smooth or Screw
N/A
5.1
6.8
2.8
Nail
Two (2)
10d
Smooth or Screw
N/A
6.9
9.2
7.3
Nall
One (1)
10d
Smooth or Screw
Feld
23.1
23.1
19.0
Nail
One (1)
10d
Smooth or Screw
Eave
29.3
29.3
24.0
"5",
Nail
TWO (2)
10d
Smooth or Screw
Field
27.6
27.6
38.6
Bella High Galena
Spanish "S" or Regal
Nail
Two (2)
10d
Smooth or Screw
Eave
38.1
38.1
41.8
Nail
- Two (2)
10d
Ring
N/A
28.6
41.2
19.4
Nail'
Two (2)'
10d'
Ring'
N/A
33.1'
48.1'
50.9'
Screw
One (1)
48
N/A
N/A
20.7
20.7
18.1
Screw
Two (2)
88
N/A
N/A
43.2
43.2
29.8
' Installation with a 4-Inch tile headlap and fasteners located min. 2X-inch from head of tile.
Exterior Research and Design, I.I.C. Evaluation Report E39310.11.11-1-R4
ceM)icote o/AuthorknNon p95o1 6'n EDITION (2017) FBC HVHZ EVALUATION FL7804-R10
Entegra Roof Tiles Revision 4:10/17/2017
Page 6 of 8
I�
TRINITY ERD
TABLE 4: ATTACHMENT RESISTANCE EXPRESSED AS A MOMENT —MF (FT-LBF)
MORTAR AND ADHESIVE -SET SYSTEMS
Note from Entegra Roof rile, LLC.: The performance data listed in Table:4 are based on the respective adhesive manufacturers' test
reports and Miami -Dade NOAs. Entegra Roof Tile, {LC. relies upon the adhesive manufacturers.. to provide these values for our. inclusion.
in this FBC HVHZ Evaluation Report Please consult the individual adhesive manufacturer, for information on product approvals,
d d overturning Moment Performance.
limitations, revisions or other information for determining wind loRW
T
Tile
Bermuda
Product
'TILE BOND^"' by Dow Chemical
'Touch N' Seal Storm Bond" by DAP Foam
roval
2.01
1.03
Placement
Interdependent (2-paddy)
Interdependent (2-paddy)
Mf(ft-Ibf)
41
73
Flat,
Plantation
"Polyseta RTA-1" by ICP Adhesives & Sealants
5.03
Interdependent (2-paddy)
Interdependent
52
43
Flat or
Horizon
"Polyseta AH-160" by ICP Adhesives &
Sealants
22.03
Independent (medium paddy, `30 g)
51
Independent (large paddy, ^'45 g)
92
"TILE BOND`"" by Dow Chemical
'Touch N' Seal Storm Bond" by OAP Foam
NOA 16-0222.01
NOA 16-0421.03
Interdependent (2-paddy)
Interdependent (2-paddy)
44
42
Estate "5" or
"Polyseta RTA-1" by ICP Adhesives & Sealants
NOA 16-0315.03
Interdependent (2-paddy)
Interdependent (2-paddy)
44
50
Independent (medium paddy, "30 g)
37
Hacienda
"Polyseta AH-160" by ICP Adhesives &
NOA 17-0322.03
Independent (large paddy,-54 g)
61
Sealants
Bella High
"S", Galena
Mortar
"TILE BOND^" by Dow Chemical
'Touch N' Seal Storm Bond" by DAP Foam
"Polyseta RTA-1" by ICP Adhesives & Sealants
Various
NOA 16-0222.01
NOA 16-0421.03
NOA 16-0315.03
Per RAS 120
Interdependent (2-paddy)
Interdependent (2-paddy)
Interdependent (2-paddy)
Interdependent(2-paddy)
21
48
52
36
30
Independent (medium Paddy, —30 g)
49
Spanish "S"
or Regal
°Polyseta AH-160" by ICP Adhesives &
Sealants
NOA 17-0322.03
Independent (large paddy,-63 g)
94
Mortar
various
Per RAS 120
25
LABELING:
7.1 Each unit shall bear the imprint and/or identifiable marking of the manufacturers name or logo, as detailed
below. Tile lots shall be labeled in accordance with the requirements of the Accredited Quality Assurance
Agency noted herein.
and/or
6M�7E N T E G, R A
Labeling: Bermuda Flat, Plantation Flat, Estate "S", Bella High "S", Galena Spanish "S"
Exterior Research and Design, U.C.Evaluation Report E39310.11.11-1-R4
FL7804-R30
6r" EDITION FBC HVHZ EVALUATION
Certifimte ofA"Mari:aaon N95a3 I Revision 4: lo/17/2017
Entegra Roof Tiles Page 7 of 8
TRINITY: ERD
Hanson
8. BUILDING PERMIT REQUIREMENTS:
2
10.
Labeling: Horizon Flat, Hacienda, Regal
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
MANUFACTURING PLANTS:
Plant.
Profiles
Okeechobee, FL
Bermuda Flat, Plantation Flat, Estate'$", Bella High "S", Galena Spanish "S"
Ft. Myers, FL
Horizon Flat, Hacienda
Deerfield Beach, FL
Horizon Flat, Hacienda, Regal
QUALITY ASSURANCE ENTITY:
PRI Construction Materials Technologies, LLC.—QUA9130; (813) 621-5777
- END OF EVALUATION REPORT —
Exterior Research and Design, U-C. Evaluation Report E39330.11.114-R4
Cerdreate ofAutharimtlon x95a3 a EDITION (Z017) FaC HVHZ EVALUATION FL7804-R30
Entegra Roof Tiles Revision 4:10/17/2017
Page 8 of 8
F P
REVIEWED FORto C%
CODE COMPLtANIC D
ST. LUCIE CO O UAIMNED
BOCC k7 By
St; Lucie County
NEOREi
Certifim[e of Authorization #32455
353 Christian Street, Unit #13
Oxford, Cr 06478
(203)262-9245
ENGINEER EVALUATE TEST CONSULT t.ERllrT
Boral Roofing Evaluation Report M35710.12.10-R11
FL14317-R10
7575 Irvine Center Drive, Suite 100 Date of issuance:12/21/2010
Irvine, CA. 92618
Revision 11: 10/12/2018
(602)269-2288
SCOPE:
This Evaluation Report is issued under Rule 614320-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code andiFlorida Building Code, Residential Volume. The products
described herein have been evaluated for compliance with the 6"' Edition (2017) Florida Building Code sections noted
herein.
DESCRIPTION: Boral Roof Underlayments
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until suih time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of th1e Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreementto notify Robert Nieminen, P.E. of any changes to the
product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a complete review of
this Evaluation Report relative to updated Code requirementslwith each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded bylthe words "NEMOletc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8
Prepared by:
`31 "....1
_
'd.a.....a-.......-F�'
-
Robert J.M. Nieminen, P.E.
The faaimileseal appearingwas authorized byRoben
Florida Registration No. 59166, Florida DCA ANE1983
_L,, � � �'"
Nieminen, P.E. on 10/12/2018. This does not serve as an
electroniolly signed document
CERTIFICATION OF INDEPENDENCE: I
1. NEMO ETC, LLC does not have, nor does it intend to acquire or % II it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. 1 ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product. I
5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions the Ieof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
0
I11EM0 I etc.
ROOFING COMPONENT EVALUATION:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Boral Roof Underlayments, as marketed by Boral Roofing, have demonstrated
compliance with the following sections of the 6' Edition (2017) Florida Building Code through testing in
accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations
/ Conditions of Use set forth herein.
1504.3.1
1507.1.1, T1507.1.1,
1507.2.9.2
1507.3.3
Enti
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD M 6049)
OC (PDM3838)
PRI (TST 5878)
PRI (TST5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
UL, U.C. (QUA 9625)
Property
Wind Uplift
Physical Properties
Physical Properties
Examination
Physical Properties
Physical Properties
Tensile Adhesion / LTA
Adhesion
Tensile Adhesion / LTA
Tensile Adhesion / LTA
Physical Properties
ASTM D1970
ASTM D1970
Tensile Adhesion / LTA
FRSA/TRI April 2012
ASTM D1970
Wind Uplift
Wind Uplift
Tensile Adhesion / LTA
ASTM D1970 (adhesion)
Quality Assurance
4.1 Boral® TileSeal 56"r is a nominal 50-mil thick,
underlayment; meets ASTM D1970.
4.2 BoralO TileSeal"T is a nominal 60-mil thick, I
underlayment; meets ASTM D1970 and FRSA/TRI
4.3- BoralO MetalSeal"T is a nominal 60-mil thick,
underlayment; meets ASTM D1970 and FRSA/TRI
4.4 GatorSeal® is a nominal 55-mil thick, granular-sul
roof underlayment; meets ASTM D1970.
4.5 Citadel® Plus is a nominal 48-mil thick, fabric-sur
roofing underlayment for use as a base -layer in IT
UL 1897
ASTM D1970
FRSA/TRI April 2012 (04-12)
Reference
M36790.07.11
B40380.08.12
C41420.09.12-2
B41940.09.12
B47390.07.14-1
947390.09.14
Equivalency statement
NEI-031-02-02:REV
NEI-029-02-01:REV
NEI-046-02-01REV
NEI-076-02-01
NEI-034-02-02
BORR-001-02-01
BORR-005-02-01
DAPF-002-02-01
OCF-443-02-01
Service Confirmation
Year
2012
2015
2012
o9/30/2011
08/28/2012
09/21/2012
09/13/2012
07/31/2014
09/04/2014
11/02/2017
10/27/2010
12/03/2010
12/17/2010
02/14/2011
01/29/2013
03/17/2015
06/24/2015
03/08/2018
10/11/2018
Exp.08/21/2020
SBS modified bitumen
self -adhering SBS modified bitumen roof
self -adhering SBS modified bitumen roof
fiberglass reinforced, self -adhering SBS modified bitumen
fiberglass reinforced, self -adhering SBS modified bitumen
y underlayment systems; meets ASTM D1970.
NEMO ETC, LLC Evaluation Report M35710.12.10-R11
CerCfi ofAuthonzation S32455 6- EDITION (2017) FBC NON-4HZ EVALUATION FL14317-RID
Boral Roof Underlayments; (602) 269-2298 Revision 11: 10/12/2018
Page 2 of 8
ONEMOletc.
5.1 This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer
of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting
or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Laboratory Report; refer to current Approved Roofing Materials Directory for
fire ratings of this product.
5.4 Boral Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If not listed, a request may be made to the Authority Having Jurisdiction for
approval based on this evaluation combined with supporting data for the prepared roof covering.
5.5 Allowable Roof Covers: Table 1 pertains to use of each listed underlayment by -itself beneath the stated roof
.._a__._.,_:_..-u-.;--;-,,,,,, inncfnrmulti-nlvunderlavmentoDtions.
5.5.1
ROOF • • OPTIONS
Underlayment
Asphalt
-
Nail -On Tile
rle
Adhesive-setMNoYes
hk
late
Shingles
Boral TileSeal 50v
Yes
No
Noes
oral TileSealw
Yes
Yes
Yeses
(See 5.5.1)
Boral MetalSeal"T
Yes
Yes
YesYes
(See 5.5.11
GatorSeal
Yes
No
NoYes
— __ __ __. rn_„ :_ 1:...;.^A ... „— -f fnun.e,inn Annrnved tile adhesives / underlayment combinations.
Florida Product
Underlayments
Adhesive Approval
DAP Foam Touch'n Seal Stormllond Roof Tile Adhesive
FL14506
Boral TileSealw or Boral MetalSeal'
DAP Foam Touch'n Seal StormBond 2 Two -Component
FL21374
Boral TileSeaPn or Boral MetalSealm
Polyurethane Roof Tile Adhesive
Dow TILE BOND"' Roof Tile Adhesive
FL22S25
Bor4l TileSealur or Boral MetalSealm
ICP Adhesives Polysete AH-160
FL6332
Boral TileSealvr or eoral MetalSealM
ICP Adhesives Polysete RTA-1
FL6276
Boral TileSealvr or Boral MetalSealw
Refer to Tile Manufacturer's or Adhesive Manufacturer's Florida Product Approval for overturning Moment Resistance Performance.
Evaluation Report M35720.12.10-RII
NEMO ETC, LLC FL14317-R70
ee.o'fimre oj4uMon:naon #32455 6TMEDITION (2017) FBC NO N-HVHZ EVALUATION
Boral Roof Underlayments, 269-2298 Revision 11; 10/12/2018
Page 3 of 8
ONEMOletc.
5.6 Allowable Substrates:
5.6.1 Direct -Bond to Deck:
Citadel Plus, Boral TileSeal 50", Boral TileSeal"T, Boral MetalSeal"r or GatorSeal:
➢ Plywood (unprimed or primed with ASTM D41 primer).
Boral TileSealln or Boral MetalSeal"r:
➢ OSB (unprimed or primed with ASTM D41 primer).
Note: Refer to Section 5.6.4 for uplift limitations associated with direct -deck Underlayment installations where the
overlying roof cover is adhesive -set tile roofing
5.6.2 Bond to Base Laver Underlayment:
Citadel Plus, Boral TileSeal 50"T, Boral TfleSealw, BoralMetalSeal"r or GatorSeal:
➢ ASTM D226, Type II felt; Citadel Plus.
For installations under mechanically attached prepared roof coverings, base layer shall be attached per minimum
codified requirements. For installations under adhesive -set tile systems, base layer shall be attached per minimum
requirements of FRSA/TRI April 2012 (04-12), Appendix;A, Table 1, or as listed in Section 5.6.4 herein, or as tested
in accordance with FBC 1504.3.1.
5.6.3 Bond to Other Substrate Types:
Citadel Plus, Boral TileSeal 5011T, Boral TileSeal"T, Boral MetalSeal"T or GatorSeal:
➢ ASTM D41 primed metal (e.g., flashing metal, valley metal, etc.).
Boral TileSeal"r:
➢ Huber Zip Deck (unprimed or primed with ASTM D41 primer); Dens Deck Prime.
Note: For installation under mechanically attached prepared roof coverings, insulation shall be attached per
minimum requirements of the prepared roof covering manufacturer's Product Approval.
5.6.4 Wind Resistance for Underlayment Systems in Adhes(ve-set Tile Applications: FRSA/TRI April 2012 (04-12) does
not address wind uplift resistance of all underlayment systems beneath adhesive -set tile systems, where the
underiayment forms part of the load -path. The following wind uplift limitations apply to underiayment systems
that are not addressed in FRSA/TRI April 2022 (04-12),and are used in adhesive -set file applications. Maximum
Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the
ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer
to FRSA/TRI April 2012 (04-12), Appendix A, Table 1A or FBC 1609 for determination of design wind loads
#1 Maximum Design Pressure = -120.0 post:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Primer: (Optional) ASTM D41 to the plywood deck
Base Ply: Citadel Plus, self -adhered
Cap Sheet: Boral TileSeal"T or Boral MetalSeal"T, self -adhered, and back -nailed within the selvedge -edge side laps
using 12 ga. x V14" ring shank nails through 32 ga.,1-5/8" diameter tin caps spaced 12-inch o.c.
#2 Maximum Design Pressure=-142.5 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Ply: None
Cap Sheet: Boral TileSealw or Boral MetalSeal", self -adhered and back -nailed within the selvedge -edge side laps
using 12 ga. x 1Y" ring shank nails through 32 ga.,1-5/9" diameter tin caps spaced 124nch o.c.
Evaluation Report M35710.12.10-R31
NEMO ETC, LLC
Cervfcate of Authorfmtion#32455 6'"EDITION(2017J FBC NON-HVFIZ EVALUATION FL14317-R70
Boral Roof Underlayments; (662) 269-2288 Revision 11: 10/1Z/2018
Page 4 of 8
*NEMOletc.
#3 Maximum Design Pressure = -202.5 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Primer: Tropical Roofing Products #410 Quick Dry Primer or other ASTM D41 primer to the plywood deck
Base Ply: None
Cap Sheet: Boral TileSeaForBoral MetalSeal",self-adhered, and back -nailed within the selvedge -edge side laps
using 12 ga. x 1%" ring shank nails through 32 ga.,1-5/8" diameter tin caps spaced 12-inch o.c.
#4 Maximum Design Pressure =-210.Opsf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Primer: KARNAK #89 Sta-Tak Primer to the plywood deck
Base Ply: None
Cap Sheet: Boral TileSeal"T or Boral MetalSeal"r, self -adhered, and back -nailed within the selvedge -edge side laps
using 12 ga. x 1'/4" ring shank nails through 32 ga.,1-5/8" diameter tin caps spaced 12-inch o.c.
#5 Maximum Design Pressure=-120.0 psf:
Deck: Min. 2,500 psi structural concrete to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Primer: A5TM D41 to the concrete deck
Base Ply: (Optional) Citadel Plus, self -adhered
Cap Sheet: Boral TileSeal"rorBoral MetalSeal'n,self-adhered
5.6.4.1 Note: For adhesive -set file systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design
pressure requirements may not exceed -120 psf.
5.7 Exposure Limitations:
Gatorseal shall not be left exposed for longer than 30-days after installation, prior to placement of final roof cover.
Boral TileSeal 50"T, Boral TileSeal"r or Boral MetalSeal"T shall not be left exposed for longer than 180-days after
installation, prior to placement of final roof cover.
Citadel Plus, for use as a base -layer in a multi -ply underlayment system, shall not be left exposed for longer than
180-days after installation, prior to placement of subsequent underlayment layer.
5.8 Tile Slippage Limitations [FRSA/TRI April 2012 (04-12)1:
When loading roof tiles on the underlayment in direct -deck tile assemblies, the maximum roof slope shall be as
I-1i ..,. Ti — �i....e nmit.tinnc ran nnly he exceeded by using battens during loading of the roof tiles.
Underlayment
Tile Profile Staging Method
Maximum Slope
Boral TileSealw or
Boral MetalSeal'
Flat Max. 10-tile stack
6:12
Lugged Max.10-tile stack
6:12
6.1 Boral Roof Underlayments shall be installed in accordance with Boral Roofing published installation instructions
subject to the Limitations setforth in Section 5 herein and the specifics noted below.
6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to
remove any dust and debris prior to application, and prime the substrate (if applicable).
6.3 Install self -adhering underlayment when ambient and surface temperatures are minimum 40OF and rising.
NEMO ETC, LLC Evaluation Report M35710.1210-R11
Certificate of AuthoraUtion#32455 6'"EDITION (2017)FBC NON-HVHZ EVALUATION FL14317-R10
Boral Roof Underlayments, (602) 269-2288 Revision 11: 10/12/2018
Page 5 of 8
ONEMOletc.
6.4 I Citadel Plus-
6.4.1 Citadel Plus is limited to use as a base or mid -layer in multi -ply underlayment systems beneath Boral TileSeal 50"r,
Boral TileSeal"r or GatorSeal.
6.4.2 Slope limitations are those associated with the tap -layer underlayment.
6.4.3 Direct to Deck:
Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge,
extending over by''/< -inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place
the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with
a weighted roller.
Fasten the top edge of the sheet to the deck with corrosion resistant roofing nails, nails & tin -tags or 1-inch
diameter plastic or steel cap nails spaced maximum 12-inch o.c. Overlap successive courses the entire width of the
black -selvedge area, minimum 2 inches (horizontal lap) and minimum 6" end (vertical) laps.
Install final underlayment layer atop Citadel Plus per 'direct -to -deck' instructions for Boral TileSeal 501IT, Boral
TileSeal"', Boral MetalSealw or GatorSeal.
6.4.4 To Base Sheet:
Install base sheet of ASTM D226, Type 11 felt in accordance with Code requirements or install base ply of Citadel
Plus in accordance with Boral Roofing published installation instructions and Section 6.4.3 and when used as part
of a multi -ply system.
Install optional Citadel Plus as a mid -ply in accordance with Boral Roofing published installation instructions and
Section 6.4.3.
Install final underlayment layer atop Citadel Plus per 'direct -to -deck' instructions for Boral TileSeal 5011r, Boral
TileSeal' or GatorSeal-
Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design
pressure requirements may not exceed -120 psf.
6.5 Boral TileSea150"r•
6.5.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment In FBC Table 1507.1.1 for
the type of prepared roof covering to be installed.
6.5.2 Do not use Boral TileSeal 50w on roof pitches less than 2:12.
6.5.3 Non -Tile Applications Direct to Deck:
Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge,
extending over by Y-inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place
the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with
a weighted roller.
Fasten the black selvedge edge to the deck with corrosion resistant roofing nails, nails & tin -tags or 1-inch diameter
plastic or steel cap nails spaced maximum 24-inch o.c. for slopes below 7:12 and maximum 124inch o.c. for slopes
7:12 and greater. Overlap successive courses the entire width of the black -selvedge area, minimum 3-Inch.
Seal under end (vertical) laps using approved mastic, or use Joined and Folded Seam or Inverted Sheet Seam
method detailed in Boral Roofing published installation instructions.
NEMO ETC, LLC Evaluation Report M35710.12.10•R31
FL14317-RIO
CertifimMofAUNmkation 932455 6TM EDITION (2017) FBC NON-HVHZ EVALUATION Revision 11: 10/12/2018
Boral Roof Underlayments; (602) 269-2288
Page 6 of 8
ONEM10jetc.
6.5.4 Non -Tile Applications to Base Sheet:
Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance with
Boral Roofing published installation instructions and Section 6.4.
Install Boral TileSeal 50w in accordance over ASTM D226, Type II felt or Citadel Plus with Boral Roofing published
installation instructions and Section 6.5.3, except end (vertical) laps, described below.
Apply SBS Mastic under all end (vertical) laps or any other laps where the self -adhering bituminous underside is in
contact with the fabric top surface, rolling the interface into place with a weighted roller.
6.6
6.6.1
6.6.2
6.6.3
6.6.4
I- Gatorseal•
Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table 1507.1.1 for
the type of prepared roof covering to be installed.
Do not use GatorSeal on roof pitches less than 2:12.
Non -Tile applications Direct to Deck:
Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge,
extending over by Y-inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place
the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with
a weighted roller.
Fasten the black selvedge edge to the deck with corrosion resistant roofing nails, nails &tin -tags or 1-inch diameter
plastic or steel cap nails spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes 7:12 and greater.
Overlap successive courses the entire width of the black -selvedge area, minimum 3-inch.
Seal end (vertical) laps using SBS Mastic under all side (vertical) laps or any other laps where the self -adhering
bituminous underside is in contact with the granular or mineral top surface, rolling the interface into place with a
weighted roller, or using the Inverted Sheet Seam detailed in Boral Roofing published installation instructions.
Non -Tile Applications to Base Sheet:
Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance with
Boral Roofing published installation instructions and Section 6.4.
Install GatorSeal overASTM D226, Type 11 felt or CitadelIPlus in accordance with Boral Roofing published installation
instructions and Section 6.6.3 except end (vertical) laps, described below.
Apply SBS Mastic under all side (vertical) laps or any other laps where the self -adhering bituminous underside is in
contact with the granular top surface, rolling the interface into place with a weighted roller.
6.7 I Boral TileSeal"r or Boral MetalSeal"' I I ' - -
6.7.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table 1507.1.1 for
the type of prepared roof covering to be installed.
6.7.2 Do not use Boral TileSeal" or Boral MetalSeal"r on roof pitches less than 2:12.
6.7.3 Non -Tile Applications Direct to Deck:
For OSB substrate, prime with ASTM D41 primer and allow to dry prior to installation. Cut the membrane into
manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending over by X-inch.
Fold the membrane away from the edge onto itself. Remove the release sheet. Place the membrane with the
exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with a weighted roller.
Fasten the black selvedge edge to the deck with roofing nails, nails & tin -tags or 1-inch diameter plastic or steel
cap nails spaced maximum 12-inch o.c. Overlap successive courses the entire width of the black -selvedge area,
minimum 3-inch.
Seal under all end (vertical) laps using approved mastic or use Inverted Sheet Seam method detailed in Boral
Roofing published installation instructions.
NEMO ETC, LLC Evaluation Report M35710.12.10-RSl
Oe�f,mre ofAuthorrsation#32455 0 EDITION (2017) FBC NON-HVH2 EVALUATION FL14317-R10
-- Boial Roof Underlayments; (602) 269-2288 ---- Revision 11: 10/12/2018
Page 7 of 8
0
NEMO I etc.
6.7.4 Non -Tile Applications, to Base Sheet:
Install ASTM D226, Type II felt in accordance with code requirements or install Citadel Plus in accordance with
Boral Roofing published installation instructions and Section 6.4.
Install Boral TileSeal"T or Boral MetalSealHr over ASTM D226, Type II felt or Citadel Plus in accordance with Boral
Roofing published installation instructions and Section 6.7.3, except end (vertical) laps, described below.
Apply SBS Mastic under all end (vertical) laps or any other laps where the self -adhering bituminous underside is in
contact with the fabric top surface, rolling the interface into place with a weighted roller.
6.7.5 Tile Applications:
Reference is made to FRSA/TRI April 2012 (04-12) Installation Manual and Table 1 herein, using the instructions
noted above as a guideline.
For mechanically fastened tile roofing over 2-ply system[, consisting of Base Sheet and self -adhering top sheet(s),
Base Sheet fastening shall be not less than FRSA/TRI April 2012 (04-12), Table 1.
For adhesive -set the applications, refer to Section 5.6.4 herein.
Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design
pressure requirements may not exceed -120 psf. i
Refer to Section 5.8 for tile staging limitations. Battens; must be used for all tile installations atop Boral TileSealw
or Boral MetalSeal' with roof pitches of 2%to less than 3:12. Boral Roofing's Elevated Batten System or counter
battens are required.
7. t@UILDiNG PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
i
Brentwood, NH
UL, LLC.—QUA9625; (631) 546-2458; Kanchi Agrawaia-UOKanlale+ul,t
- END OF EVALUATION REPORT -
Evaluation Report M35710-12-10-R31
NEMO ETC, LLC FL14317-R30
`-- —Cer/tificdte affruthonxarian R32955----6mZDLTIOW20171FBCNON-}iVHZ EVALUATION
Boml Roof Underlayments, (6D2) 269-2288 Rein Pages
sari IT:3of 8
Page B 8