HomeMy WebLinkAboutMANUAL - SPAI AC
L
SWIM SPAS OWNER'S MANUAL
Pinnacle Spas
6101 46th St. N.
St. Petersburg, FL 33714
727.573.9611
pinnaclespas.com
SCANNED
BY
St. Lucie County
File cop
RIS WVW�EEF 0 R
CODE COMPLiANCE
ST. LUCIE CO;UnTy
BOCC
Owner's Information
Dealer:
Date Purchased:
Company:
Address:
Telephone:
Installer:
Date Installed:
Company:
Address:
Telephone:
Swim Spa:
Date Delivered:
Model:
Color:
Serial Number:
Your unique swim spa serial number is located on a data plate outside
the cabinet at ground level. When calling for service, please have your
serial number in hand.
Ovirnees Manual
Table of Contents
Introduction............................................................................................ 2
Important Safety Information ............................... .................................. 3
Site Selection and Installation ................................................................ S
Electrical Specifications .................................................................... ... 10
Electrical Services ........................................................... -- ................. 12
iWi I Diagrams ................................................................................... 15
a .................................................................................................. 25
WaterBalancing ............................... ................................................... 30
Topside Controls & Operation .............................................................. 31
Optional Audio and Docking station ..................................................... 47
Cover.................................................................................................... 48
Frequently Asked Questions ................................................................ 49
Troubleshooting................................................................................... 51
Maintenance and Care ......................................................................... 53
Specifications....................................................................................... 57
Notes.................................................................................................... 85
Important: Pinnacle Spas is dedicated to offering you the best in customer
satisfaction and service. Be sure to read, complete, sign, and send in the
limited warranty card within 30 days of purchase to ensure you understand
what you are entitled to in terms of service. If you have any questions, you can
call our customer care center at 727.573.9611
Printed in the U.S.A.
Version 2.5 Revised 03/2015 Part # 7068
Copyright 02010, Pinnacle Spas. All rights renewed, No portion of this manual maybe reproduced In any mammor
without express written permission of Pinnacle Spas, Pemade Spasm Swim spas and Fitness Trainers are trademarks of
Pinnacle Spa.. Ali other brands, product names, company names, trade names, trademarks, and service marks used
are the property of their respective owner. Pinnacle Sees may make product modifications and enhancements.
Specifications may change Wheat notice. International products may be configured differently to meet local electrical
requirements. Dimensions are approximate. Patents pending.
Page I
For HELP, call 727,573.9611
. . ( 14
In trodu cti on
Your choice of a Pinnacle Spas� brand �wirn spa from Pinnacle Spas indicates
that you are devoted to excellence. The management and staff appreciate your
patronage and takes pride in the tradition of quality swim spas that our
company represents.
To properly acquaint yourself with your swim spa, we suggest that you take time
to read through this manual before hook up and operation. Doing so will
familiarize you with important operating and safety procedures, thereby ensuring
an enjoyable experience right from the start.
If you need any more information than this manual provides, feel free to visit our
Web site at pinnaclespas.corn or call our customer care center, at
727.573.9611.
WARNING: This manual was written to ensure the proper use and installation
of your swim spa. Any modifications to the procedures outlined in
this manual may result in voiding your warranty.
This manual and its contents are subject to change without notice. Although we
have prepared this manual as accurate as possible, we are not liable for errors or
omissions; loss, injury, or damages caused by improper installation; or use of
swim spa (improper or otherwise).
Your new swim spa is made with quality synthetic cabinet materials. Synthetic
materials won't fade and are nearly invulnerable to mold and mildew. Where
wood splits, cracks, and stains, synthetic materials stand in timeless perfection.
4—,
Figure 1 — Dual Zone IS
Page 2
For HELP, cail 727,573.9611
4
NO DIVING
DANGER: DIVING MY RESULT IN SERIOUS INJURY OR DEATH
F Emir -as
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Your physiological response to hot water depends on subjective factors such as
age, health, pregnant women, temperature sensitivities, chemical sensitivities,
and medical history. Always consult a physician before using a swim spa to
understand your particular tolerance and limitations.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING — To reduce the risk of injury, do not permit children to use this
product unless they are closely supervised at all times.
A wire connector is provided on this unit to connect a minimum #6 (AWG) solid
copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the
unit.
** For units with GFC1. AWarning — This product is provided with a ground -
fault circuit interrupter located in the main panel. The GFCI must be tested
before each spa use.
RISK OF ACCIDENTAL DROWNING: Extreme caution must be
exercised to prevent unauthorized access by children. To avoid
accidents, ensure that children cannot use this spa unless they are
supervised at all times. Always cover the swim spa and use safety
locks when it is not in use.
RISK OF INJURY: The suction fittings in this spa are sized to match
the specific water flow created by the pump. Should the need arise
to replace the suction fittings or the pump, be sure that the flow rates
are compatible. Never operate the spa if the suction fittings are
broken or missing. Never replace a suction fitting with one rated less
than the flow rate marked on the original suction fitting.
RISK OF ELECTRIC SHOCK: Install at least 5 feet (1.5 m) from all
metal surfaces. As an alternative, a spa may be installed within 5
feet of metal surfaces if each metal surface is permanently
connected by a minimum #6 (AWG) solid copper conductor to the
wire connector an the terminal box that is provided for this purpose.
RISK OF ELECTRIC SHOCK: Do not permit any electric appliance,
such as a light, telephone, radio or television, within 5 feet (1.5 m) of
a spa. Do not operate such an appliance from either inside the swim
spa or when you are wet, unless such appliances are built-in by the
manufacturer.
Page 3
For HELP, call 727.573.9611
V
NO DIVING
DANGER: DIVING MY RESULT IN SERIOUS INJURY OR DEATH
M1111119�� - - —
A TO REDUCE THE RISK OF INJURY:
The water in a spa should never exceed 40*C (1 04'F).
Water temperatures between 38*C (11 00*F) and 40'C
(1 04'F) are considered safe for a healthy adult, Lower
water temperatures are recommended for young children
and when spa use exceeds 10 minutes.
Since excessive water temperatures have a high potential
for causing fetal damage during the early months of
pregnancy, pregnant or possible pregnant women should
limit spa water temperatures to 38*C (11 00'F).
Before entering a spa/swim spa, the user should measure
the water temperature since the tolerance of water
temperature regulating devices varies.
The use of alcohol, drugs or medication before or during
spa/swim spa use may lead to unconsciousness with the
possibility of drowning.
Obese persons and persons with a history of heart disease,
low or high blood pressure, circulatory system problems, or
diabetes should consult a physician before using a spa.
Persons using medication should consult a physician before
using a spalswim spa since some medication may include
drowsiness while other medication may affect heart rate,
blood pressure and circulation.
Do not connect auxiliary components (such as headphones, cables,
and additional speakers) to the stereo (if equipped).
Do not use a swim spa immediately following strenuous exercise.
Do not use your swim spa alone.
Lock the cover on your swim spa when not in use.
Persons with infectious diseases should not use a swim spa.
Replace audio components only with identical components.
Do not leave the OD/Stereo/MP3 access door open on the stereo (if
equipped).
Some types of hair dye can react with the sanitizers in your swim spa
water causing your hair to change color. Use at your own risk.
Water normally splashes out of a swim spa during typical use. Install
an adequate perimeter that provides sound footing.
Do not turn your swim spa on/off from a wall switch, ground fault
circuit interrupter, circuit breaker, fuse, or by plugging/unplugging it.
Remove all jewelry, metal, and watches from your person before
entering your swim spa.
Keep all breakables away from the swim spa area.
A Maintain water balance in accordance with instructions.
Do not sit on lip of the spa.
4
NO DIVING
DANGER: DIVING MY RESULT IN SERIOUS INJURY OR DEATH
Warning Sign Must Be Posted — The
red WARNING sign like the one shown is
packed with your new swim spa. This
sign must be posted in a prominent place
EG=ME KGF�M�
in close proximity to the swim spa
f installation site immediately upon
completion of swim spa installation.
Rt.DWMMRISQVEDENDYADEDW��
Figure 2 —Warning Sign
Important: It is extremely important that this sign be permanently placed in clear
view of persons using the swim spa. Occasional swim spa users may not be
aware of some of the dangers hot water poses to pregnant women, small
children, seniors, and people under the influence of alcohol. If you did not
receive a warning sign or your sign has become damaged, please call your local
dealer for a replacement.
Hyperthermia
To reduce the risk of injury, the water temperature in a swim spa should never
exceed 104'F (40'C). Water temperatures between 1 00*F (38*C) and 104*F
(40'C) are considered safe for a healthy adult. Lower water temperatures are
recommended for young children, senior citizens, persons with sensitivities, and
when swim spa use exceeds 10 minutes.
WATER TEMPERATURE IN EXCESS OF 1 00-F (38-C) MAY BE INJURIOUS
TO YOUR HEALTH.
Hyperthermia occurs when the internal temperature of the body reaches a level
several degrees above the normal body temperature of 98.67 (37*C). The
symptoms of hyperthermia include drowsiness, lethargy, and an increase in the
internal temperature of the body. The effects of hyperthermia include:
,& Unawareness of impending hazard
A Failure to perceive heat
Failure to recognize the need to exit swim spa
Physical inability to exit swim spa
Fetal damage in pregnant women
Page 5
For HELP, call 727,573.9611
A Unconsciousness and danger of drowning
If you sense any of the symptoms of hyperthermia, safely exit the swim spa
Immediately.
SAVE THESE INSTRUCTIONS
Basic Safety Guidelines
Your hot tub is meant to be enjoyable, healthful, and relaxing. Below are some
basic safety guidelines to follow every time you use your hot tub.
Always check the temperature of your hot tub before entering. High water
temperatures can be hazardous to your health.
• Persons suffering from heart disease, diabetes, high or low blood pressure,
and pregnant women should consult a doctor before using your hot tub.
• Persons under the influence of medication, drugs, or alcohol should not be
allowed into your hot tub.
• Remove all jewelry, metal, and watches from your person before entering
your hot tub.
Do not allow children to use your hot tub without continuous supervision of
an adult.
• Do not use your hot tub alone.
• Test the ground fault circuit interrupter (GFCI) breaker prior to using your hot
tub each time to ensure it operates properly.
• Any electrical devices near your hot tub must be GFCl protected and out of
reach from inside the hot tub.
• Keep all breakables away from the hot tub area.
Lock the cover on your hot tub when not in use.
• Enter and exit the hot tub slowly. Wet surfaces can be slippery.
• Prolonged immersion can be hazardous to your health.
Maintain water chemistry in accordance with manufacturer's instructions.
The hot tub is not to be used by persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction
Do not sit on lip of spa.
lkicei VJJRIF
DANGER: DIVING MY RESULT IN SERIOUS INJURY OR DEATH
Page 6
I *
Basic Water Quality Guidelines
• During the initial filling of the spa, add a sequestering agent to combat
suspended minerals in the water. Allow water to circulate and filter for at
least 12 hours before adding any other chemicals.
• Test water for PH, total Alkalinity, and Calcium hardness. The PH should be
7.2-7.8 and the total Alkalinity SO- 180 PPM. Calcium hardness levels should
be maintained between 150 and 400 PPM. Adjust PH and total Alkalinity
(TA) utilizing the directions on the chemical bottles. Wait 15-30 minutes, test
and adjust if necessary.
• Add 2 ounces of concentrated chlorinating granules (sodium Dichlor-s-
triazinetreone) on initial start up to begin sanitizing the spa water. It is
important not to add the chlorinating granules until the PH, alkalinity and
calcium hardness have been adjusted to their proper levels.
Check.spa water with test strip forproper sanitation levels and adjust
accordingly to the proper levels. Free chlorine should be 2-4 PPM.
We recommend a minimum level of 2 PPM residual chlorine be maintained
in spa water. Be sure the pumps are running when adding chlorine or non
chlonne shockloxidizer.
Add 1 ounce of non -chlorine shockloxidizer or V2 ounce of chlorine to the spa
water after each spa use.
Audio components are optional and not available on all models.
WARNING: Prevent Electrocution: Do not connect any auxiliary
components — for example, cable, additional speakers,
headphones, etc., — to the system.
JECaution: Risk of Electric Shock: Do not leave audio compartment door
open. Replace audio components only with identical components.
. 10
w
Proper planning is an important consideration when installing your new swim
spa. Site selection is a critical step and requires serious thought. Planning ahead
makes the installation process easier. The following information is provided to
assist you in site preparations.
1 ) Always comply with local building codes and obtain any necessary permits.
You may also need to consult with an engineer to address your specific
design needs.
2) Contact an electrician to assess your electrical needs, install wiring, and
assure a safe operation.
3) Position your swim spa with proper access to water, drainage, and electricity.
4) For external installations, place your swim spa on a uniform solid, flat
surface desighed to properly support its weight. For external installations, a
level concrete pad or properly constructed deck capable of supporting 200
Ibs/ft2 (925 kg/M2) should be installed. For best results, we suggest the
installation of a level concrete pad. Dig out and level the ground 8-12 inches
(20-30 cm) below your desired base level. Install 4-6 inches (10-15 cm) of
crushed stone. Next, install 4-6 inches (10-15 cm) of poured concrete and
level it with a broom -type finish. Decks constructed flush to the swim spa
should slope away for proper run off. In regions where freeze/thaw occurs, or
where there will be custom decking abutting the swim spa, we recommend
the installation of poured concrete footings extending below the frost line
beneath the pad to prevent the possibility of future shifting.
5) For internal Installations, check the load carrying capabilities of the floor on
which the swim spa will reside. The ceiling should be more than 10 feet high
(for safe entry and use), the floor should have a drain for splash over and the
room should have a window or exhaust fan with humidistat for ventilation. If
this is not possible, indoor/outdoor carpeting and the use of a dehumidifier
while the cover is off should be adequate.
6) For partial In -ground installations (not recommended), follow these tips: In
non-freezing climates it is sufficient to ensure that the base of the hole or
cavity created for the swim spa simply has a stable, compacted base. Where
the climate permits, should you choose to backfill directly against the swim
spa, a clear sand backfill is suggested. Never fill using raw earth and never
cover electrical components or plumbing connections. - In climates where
freeze/thaw occurs, it is necessary that a proper poured concrete base,
complete with concrete footings. - In areas with a high ground water table,
the concrete base, as well as a concrete or wood retaining wall to hold back
the earth, is suggested. This forms a box or "crib/vault" where the swim spa
is placed. After excavating the installation site for your Pinnacle Spas
Page 8
7.573.9611
swim spa, ensure that the soil underlying the foundation is capable of
supporting a minimum of 1,000 lbs/ ft2 or 12,206 kg/M2 - ALWAYS ensure
that there is good drainage, via a properly designed (gravel) drain system
and/or a sump pump, to prevent ground water flooding damage to the
support equipment or structure. Install protective waterproof conduit to
house light, or topside control cables that must be buried. Access for future
service must be considered at the time of design and installation. Difficult
access can result in supplemental service labor charges not covered by the
factory warranty. Consider easily removable deck materials.
7) Assure that your swim spa will fit into the space you have chosen and the
delivery route -will accommodate its large size. In most cases, a crane Will be
necessary for the delivery.
8) Provide adequate ventilation for the humidity created by your swim spa. In
most cases, a Swim spa Hard Cover is sufficient.
9) Protect the pumps and all equipment from the weather by ensuring the
cabinet panels are secure at all times.
10) Allow 36 inches (1 meter) of unobstructed access to all sides of your swim
spa for normal servicing.
11) Contact your local building code department to determine if a building permit
is necessary and for information on applicable bylaws (distance from
property lines, buildings, fencing requirements, etc). In most cases, the
shallow depth of the unit could result in it being classified as a portable swim
spa by building regulations (as opposed to a permanent pool).
12) Consider positioning your swim spa out of or adequately protecting it from
the wind. Just as people can get cold on cool/windy days, so can your swim
spa. Windy environments can significantly increase operating costs.
F7
L.�
Figure 3 — A Crane is a Common Delivery Arrangement for Swim Spas
[Electrical Specifications
Important — Qualified and licensed electricians must perform all electrical
hookups. The following specifications must be followed in order to ensure proper
performance and safety.
WARNING: Starting an incorrectly wired swim spa could cause severe
damage to the mechanical equipment or even bodily harm. Have
your licensed electrician verify GFCl (or RCD) wiring with the
diagrams on pages 12-23 prior to starting the swim spa or call
the technical support line at 727.573.9611.
Caution: Failure to abide by specifications listed may result in damage to the
equipment and will void the warranty. All swim spas must be wired
with the appropriately sized wiring. Failure to do so will cause
equipment damage and will not be covered under your warranty. All
swim spas must be over current protected with a built-in GFCl (or
RCD) in the service panel.
Model
Service 1
Service 2
Volts/
GFOI/RGD
Wire size
control
control
Frequency
Required in
required
(controller,
(controller,
VAO/HZ
AMPS
Servicall
spa panel)
spa panel)
Servicel/
Service 2
Service2
DZ 18 (2022)
PEL2SWIM,
VS5007J
240/120/60
60/40
4 Wire #6
ML700
MVP260
4 Wire #8
BP2000,
Sp OUC
S18(2028)
PEL2SWIM,
N/A
240/120/60
60
4 Wire 461
ML900,AX20
SP2000
SpaTouch*,
AX20
E
0
4V
ESIA 1)1�
(130;!
MVp2eo
N
220-240/50
IX32
3X4
*For spas with Spa Touch panel see included 7678B Manual insert
Table 1 — Domestic/Export (in Gray) Electrical Specification Chart
NOTE: The Sevice I and the Service 2 will need to be wired independently.
WARNING: Disconnect electrical power before servicing. Before obtaining
access to terminals, all supply circuits must be disconnected.
WARNING: Test the GF01 (or RCD) before each use.
Our swim spas are certified by Intertek Testing, SNAa Ltd.
Ontario, Canada to CSA-C22.2 No. 218.1 -M89 and ANSVUL
offis
I 1563 standards.
3041384
(C amomma3mamlo
Page 12
For HELP, call 727.573.9611
do
WirinqDiagrarns — I
anportant laaamm OrMIS Gpocircuffareaker.
IMUdIIgAMpEffi EM10gand Medan QfCMdLXftr M
and qpa,musl be pertued by a Matto evaeltlaa 13
at=amm wU Me Want! Eloafflol Code. arthe
Wamn EleaRmalCode, aw aDlecerat Glar. and local
AM AN
OW 0"'111 Waaaand eguamus in embla: Ineumeoftl6mum-
rRaw"
1101e: TM atra R== Rom Imm Me tact onto Gra
MUIA be OMMMIed Re Me IMMItl 9LIRe "Wat, TIM
To
lalerna[ MeMantm of Me GFO R&CR310% Me nMb3I
CanneaRIM. Ine GM Wu MR Wait WMMUL
...... ............
r— ff " C f (SP We a)
Mgt
UK
var,
--------------
IMT FMMBI 1!71F_T_�
MI
Am L2
BDD=g
Lag
r
Figure 4— Electrical Serviceforall domestic Single-phase 240vac models
See wire size chart on page 10-11
Page 13
For HELP, ca[I 727.573.9611
Figure 6 — Electrical Service for export models, single service 1x32A,
applications.
All wiring is 3M MM2, solid copper
See wire size chart on page 11
14
ON ON ON ON ON
OFF OFF OFF OFF,
0 010 IQA 0
Grou"OR&M . *
SIC
(Ne'"), Fmmmd�raflsseewlirilig
diagram for your wwroller.
(pag� 15-23)
2
0 SON IV 01 E30 a
:Pmnd)
Figure 6— Electrical Service for three phase, 3xI6A applications.
All wiring is 5xI.5 MM2' solid copper
See wire size chart on page 11
Page 15
For HELP, call 727Z73.9611
PEL2SOM -PN 56261-01
L (,,.) m,,
63 ON 2 PINS
—i SWTCHBANK A OFF (DOVVN)ER- SWICHBANK A ON (UP)
TEST RODE UP
.4 At
TEST HOW OR
VRC#k,
� m 2 M � V�
A?
A3
� ADS 4 M P� VAAA
A4
4 um �r
musT m mr
A5
MLLT K ur
MOWER OISAmPn
M
ENAKED
MIT ASM�
A AT
-&UWER
NOT ASSIGIED
NOT ASSICKED
-d Aa
NOT ASSIGNED
JRUI-AS n
j_A9_
--
No tmf�T—
4
All,
Al2
EDIT
inb�,M-
W� R--
SMTCHBANK 8 OFF (DOM) SMICHBANK B ON (UP)
NOT ASSMED
4 BI
NOT ASSGNMI)
NOT AMCKED
.482
NOT ASSMED
INOT ED
-4-03� ---
94
NOT -ASSIGNED ... . ..... .....
NOT ASSGNED
,QT A=GNw
IA M
!NOT ASSGNED
NOT �W
[4 BB
JNOT-A�GNED
AU UMMD SHOaD a OFF
=All
I
ARTS;
mm
To
il
2 SPD Pi
20V
la
YjF --
" "
ROf bsm�
[
CA
we
I RED Ac
J4
A v
lmv
1 2A
we
�x
H�
I SPO P2
24�
%T2
RED AC
1
AC
K'R
P�LATLR
124UV
*WIF
R TERM
JIM
7 KJST ALSO BE SET ON PINS 2 AND 3 FOR A �V. SPA LMHT
IT 4
ARP BRAV NOT TO EXCEED WX �T RATING OF SPA
VFWAC
USE CUNNECTIENS AS MXRTED-INSIDE THE SYSTER ENCLOSLRE
CORRECT ONLY TO QRCWTS,PRO� BY A � A
ILocATMI
DEAMI,�rsl
A �NE"Nc UEANS MUST BE MSTA� WIM SORT FEW
rW.MXR
M-C EQU�ENT AND AT � 5 FEET (I.W M) FROW TRE
MOE W� OF THE POOL. SPA; OR NOT TM
FOR SUMY CONNECTONS. TOROUE RANGE FOR
USE COPPER CONDUCTORS MY.
USE �WcToAs sm OR TRE RAIN MMHAL � (m*
UPLOYER Mou� n
� OF W� AMPAUTY OUT 27-M ft
DES �VCMRS M �
06 AM MR. WRE- 7Y
RAM MMMUU OF 7M
0
LL
,o �
PEL2P3S2 -PN 56424
m
Tiumaut: izANGE
I'MHUM
CONNECTIONS,
XTU35
K LBS.
,(�ML�(MAIN)PANELS
El
1 r TL
MCPR��!F �I�M, Ac
CONNECT MY TO CTIZCUTTS MTECTED BY A MASS A GFCL
A DISCENNEMNG W-ANS,RUST PEINSTALLED WITHIN SIGHT F14IN
THE EXXUlPNENT AND AT LUST 5 FEET ILSE M FIZON THE
INSIDEE WALLS DIF THE POOL. VA, OR NOT TUD.
TINIQUE TZANGE FOR
unm � OLocIc
27-30 IN. UBS.
J83042RNS
SWITCHRANK A OFF COWN) IR SWITCHBANK A ON (UP)
TEST NOBE OFF
-4 At
TEST IIQDE ON
-4AB
AIOZRI�T
NOT
--on! A� ......
NOT ASSIGNED
A.fis..-
_-O, Ak_
-4 A7
mol-nSPRIED
b!qL
NOT ASSIGNED
maT
-4 A9
NOT ASSIGNED
NO EDIT
MT
AAII
W�
;4-AM
HEAMY KSET
SWITCHBANK B OFF (DOWN) SWITCHBANK B ON (UP)
I NOT ASSIGNED
1.4 111,
ASSIGNED
NOT ASSI
BE
NOT ASSIGNEI)
NOT ASSIGNED
4 .3
NOT ASSIGNED
'NUT - ASSI�D
NOT ASSIGNEI),
AIR6�
14 IS
NOT.,%SSIGNED ------
NOT ASSIGNED
NOT ASSIWV��
14
ASSIGNED
ALL UNUSEll SWITC:HES SHOULD BE OFF
LOCATIM
-DEVICE
I �`S
IS
AKPS
Fizam
TO
V PL
2 D P
DLL4
24 0V
�!
12A
vi
RED AC
je
_4
,&SP_L
"M
"M
EB�
4A
W7
m Ac
J3
ED
am
V2
IZED AC:
J4
A0
Xlav
2A
we
WffT AC
J5 .. .. .. .... ..
J12
_GZOKE__
LI
II,v
12��
IA
E
PA
V9
—REFA-C
. . . ......
VHT AC
JAS
ITTW--
iEATE;z
240
5�
TW TENN
HIN Ili,
19J37, HUST ALM IS SET ON PMS a AND 3 M A LEV SPA LIGHT
TOTAL OUTPUT � MAW NOT TO EXCEED MAX TNi`(JT,RATlNG OF VA
USE UIZT11 GIZOLIND CONNECTIONS AS TKII�1101 INSIDE TRE SYST� ENCICISUIZE
WE cupoz CoNtrucim My.
ENPLDYm UNIQUENENT?
DES CONDUCTEURS BE CUIWIG
06 AVG KIN, Vl� 73-
FOR SUPPLY CONNECTIONS,
USE SUED ON TNE
BARS OF 60-C ANPACITY BUT
RATED MINNUNI OF 7M
OD
ED
CL
Z
VS 510SZ/HS20OVS-PN 55098-02
U,
cl
L5� I �A,, �. � Ac
I C � - - 1" 1 6,-'- 12-. 1 ii5,
�E fthGE FOR
A �KNMTN WANS WST BE Ww� WINN WHT
� TEINVNA. �
Twr��Na AT�TsTzETOMM)� THE
27-M K �
NSDE W��W THE PODL. WA. M NOT TUM
� MNCE
FM HE&TER
ux�c� �CTORS ONLY.
CONNECMUN&
F AW M ME- W
W Ta M
FM �y ��
K �
WC,C�s SIZED ON THE
� OF WE WT
RATED ONNUM
USEEMIN GR� C�CMS AS MCATUD INME THE MTU EN�K
* I
SWITCHRAW A OFF CDDM SWITCH� A ON (M)
MsTmw� _JIM.
SEE TA�
� �
SEE T�E
A3
M�T��a
sv�=Rcmww�
A4
A- A-5-
SEE cm
zmaz-
A?
S �F
$VC ME
SEE -fABLE71-----
:_ _..
4,6
4,6
SCE CMC
SEE TME I
� um� M� SHMM HE CFT
TAME I
A10
13 HXM�� M
ON
�m
I �Ts
TO
ASM-M
IM AC
AT CM MUP
AV
__v
2�
IMV
M
W4
-
M AC
MNE
IM
IA
WHTAC
m UGHT
1w
12W
HIR H�U
--24W
IMW
I
TDT& �T AMP MAW NOT TO EX= UM M�T MTNG � �A
W,
LL
pi x9gig-
5 MWI
I C:) W
< c7l
2 CD
000 3> C)
!7) rj
El
Z -0
r- -z
tj C-n
m
<
C-)
i5 B PON
i"& IfA
VP N
7
Figure 10
Page 19
For HELP, call 727Z73.9611
PVS515Z -PN 55584
m
CXM
CIF-VIN
C=�Mmnm
TAME I
w
��Mm
I �TMM
K�n
I
I M
EF
MR
Fa
—WR
[
I
I Z�
I
�l
W M
�y m
A X =T� Wsm
TSMM RANM M
W AT 5��
v-mnm
,Mp�pmr
M WAM
CONNECTMO
w m 33
rm mipky cmmmnmm
K m
=�,-MTW
SA=W��=
PAIM � w
4
PGL2P3P4 -PN 56502 /WL7UN �Pm
(PAGE 1) A
At � mom ON
—�M'pz w W-; "
A,
A ic I!,
�A7 mm�
M AQ
-41111-f Sl 0:
0
2
ti SMTCHBMK B C*T. (DOWN) SOTCHBMK 8 09 (UP) C�
cm
E 3 �A�L
b
A2� . JMEBe3 w 3 �MM
OT amn, I NOT RUMMEJ1.4 N
"T
�T W M
��l , s m
RAW A
M OfF FN
I Mm
4
PGL2P3P4 (PACE 2)- PN 56502
3 X 16A
Ll (BR) I L2 (BR) I L3 (BR) IN (BL)
Ll — 230VAC 32A — N
BROW BLUE
BRAUN BLAU
BRUN BLEU
Settinqs (Software Confiqured)
SETUP I I]PTIGNF�
SETUP I DIP SWITCHES 230V 10 Ix40A I � I
r------------------------ U4
I *A ON WP) v
V "
v'vf 1111 P 1 1 1 V arr (DOWN)
2-� 1. I-VCED � z I-SPOEV � 3.
1-WEED V� .1 cm �' �. U&T. A� wul
u xv �� mm "m P� �. �VW P�
SETUP 2 DIPL SWITCHES
ON (UP)
DEE (DOWN)
A= cm UGHT, U " KAM,
m7w F� �m � P�
lx32A
ON (UP)
OFF <DOWND
e-mn 1-sPEED Pw
CM LIW. AM 'U. u x7Zw3'R'
P�
SETUP 3 DIP,SWITCHES
I
FOR �y �Txm. ME � �TMS MY� �WE ROGE FUR
ME cr� vub.m TRE. EMOYER M� um Mm& � Uml�.
xs�EMSKWE�
RATED�w� ul �'Z 041.)
4GOV 312 3xlGA
m u 00
m 0
m
m u 0
2LU Go
SPUTTER FOR SETUP I ONLY
.0
v'vf 1111 P 1 1 1 V arr (DOWN)
2-� 1. I-VCED � z I-SPOEV � 3.
1-WEED V� .1 cm �' �. U&T. A� wul
u xv �� mm "m P� �. �VW P�
SETUP 2 DIPL SWITCHES
ON (UP)
DEE (DOWN)
A= cm UGHT, U " KAM,
m7w F� �m � P�
lx32A
ON (UP)
OFF <DOWND
e-mn 1-sPEED Pw
CM LIW. AM 'U. u x7Zw3'R'
P�
SETUP 3 DIP,SWITCHES
I
FOR �y �Txm. ME � �TMS MY� �WE ROGE FUR
ME cr� vub.m TRE. EMOYER M� um Mm& � Uml�.
xs�EMSKWE�
RATED�w� ul �'Z 041.)
4GOV 312 3xlGA
m u 00
m 0
m
m u 0
2LU Go
SPUTTER FOR SETUP I ONLY
.0
PGS510SZ -PN 559,42-01
a
wil-smuff-mr--
Msm-
w
�.w
C
00
I vab
,
�ERME
(�m kQ W
W
0 -W 41�w
oN TRoL PANEL
m A
SWUC� A EFT MTOWAX A W CLIP)
jALWVJD_jR_
I AL
-tEV- WN-Mt_
SM-MKE—k--
-M;E_-ILAWX-j—
W�T��
mpw�,
kA htaE�l & .
. jw -
�=ff T� =W
-EE
T
SCE-MRC-MW TAD�F
SEE TAKE I
�AIQ
SEETAWEI
wu� S� m WF
E1717
W/s m
GS50OZ -PN 54509-01
74�RAAW
FOA WA"
tlo.:Ul N.
F31-;Tzfo�—)
IFU�
S!JIT,CHS" A EIFF (DUWW SWTCHSANK A 'A (UP)
�"Ew
AAI
wwomm
W"
SQLO ww
=��
STPIEC"IW MMM_
�F
11 A7__
M�mw
-4 AIO
WW
Vn
MORNEW
IMEA
wvvvmrt�
"=a A
LL
4
a-n t u
Important — Read these step-by-step startup procedures before starting your
swim spa. Failure to follow any of these steps listed may result in damage to the
equipment and may void your warranty.
Note: If you are unsure of any of the above Startup procedures, please call our
customer care center at 727.573.9611. For best results, read each step in
its entirety before proceeding.
A� Caution: Running the swim spa pump dry (without water running through it)
can cause IMMEDIATE damage and will void the warranty! Be sure
that the swim spa is installed properly in accordance with the
instructions in this manual.
Refer to the following picture for an explanation of your swim spa's controls,
components, and technical terms. Note that not all models have all features and
components.
91
61,
A,
0
Figure 15 — Swim Spa C211OUtS (AQ 14 Shown)
Pose 25
For HELP, call 727.573.9611
*L1
Before Adding Water
Before adding water, go through these simple steps now to prevent common
issues when setting up your swim spa for the first time. Verity that the following
have all been rechecked.
1. Turn off all power to the swim spa at the main breaker panel.
2. Open the side panels to access the internal components.
3. Check that all slide valves are opened (T-
handles pulled out) to the heater and all
pumps.
4. Check that there are no obvious signs of
loose wires or broken pipes,
5. Check that the two heater unions
are hand tight.
A\ Caution: Do not use a wrench.
Over -tightening may cause
damage to unions and
gaskets, which will not be
covered under warranty.
Figure 16 - Valve Open/Closed
Figure 17 - Unions Tight
6. Check that the unions on all pumps are tight.
7. Clean out any foreign debris from within the service access area or inside of
the swim spa itself.
8. With the drain open and filters removed, thoroughly rinse out the swim spa
with warm water until the drained water runs clear. Run water through the
filtration canister and jet lines to remove any incidental dust, dirt, and debris
that may have accumulated during shipment or installation. Drain all water
completely.
9. Make sure that the swim spa drain valve is closed and the cap is on tight
(see page 51).
10. Install the filter(s) in the filtration canister.
11. Check that all of the swim spa jets are open (turned full counter -clockwise).
12. Now is the best time to clean and polish the surfaces of your swim spa (see
page 53).
Page 26
Filling (our Swim spa
Now it's time to fill your swim spa with water. Do not turn
on the electricity yet until the swim spa is completely
filled. To properly fill your swim spa:
1 . Make sure that the filters (in the filtration canister)
are gently screwed into place. Turn them clockwise
until they stop being careful not to over -tighten them F
(this avoids cracking the filter).
2. Connect a standard garden hose to a faucet with
regular cold tap water (not softened water or hot
water).
Figure 18 — Filtration Canister
Caution: The water from your hot water tank should not be used to fill the
swim spa.
3. Put the pre -filter (if equipped') on the other end of the hose, point the pre-
filter into a suitable drain, turn on the water, and allow any sediment to be
flushed down the drain. Once the water stream runs clear, turn off the hose.
4. Put the pre -filter (if equipped) into the filtration canister and turn on the hose.
5. Fill slowly. If too much water pressure is used, foaming water can force air
into the pipes and cause startup problems.
Important: To assure that the pump is properly primed, fill the swim spa
through the filter area only.
6. Fill the swim spa until the water level is about 1" above all jets (or about MY
below the pillow). Do not over fill.
Note: Every person entering a swim spa displaces a given volume of water,
so adjust water level to the number of people regularly using the swim
spa. Turn off the hose and check again for any small leaks.
7. On dual zone swim spa it is recommended that swim side be filled first and
then the spa side.
See balanced water chart on page 29.
Draining Your Swim Spa
We recommend draining your water every 6-12 months.
I . When draining the dual zone swim spa always drain the spa side before
the swim side.
2. Locate nearest drain facility (laundry tub, floor drain, lawn, shower, etc).
3. Turn off the breaker(s) to swim spa and disconnect electrical power to
all equipment.
Pre -filters are available by calling 877.530.PARTS
Page 27
For HELP, call 727.573.9611
4. Remove the filter cartridge(s) from swim spa filters.
5. Locate the drain valve at the side of your swim spa cabinet.
6. Attach a garden hose to the drain-valve(s), open the drain -valve and
drain swim spa.
7. Monitor the swim spa while it drains.
8. Use another garden hose to wash down interior surface as the swim
spa continues to drain.
9. Completely flush the old water from plumbing lines, allow fresh water to
fill into foot well area while the old water continues to be drained. When
the water from the drain hose turns clear close drain -valve.
Note: For faster draining, you may use a sump pump or siphon.
Operational Checking Your Swim S a
Caution: Do not turn on any pump until your swim spa is properly filled with
water. Running any pump without water in your swim spa can cause
IMMEDIATE damage, which is not covered under warranty!
By now you have rechecked your swim spa's mechanical connections and filled it
with water to about I " above all jets by adding cold tap water through the pre-
filter (if equipped). Turn on power to the swim spa at the main breaker panel and
test the operation of the electrical system. If you encounter a problem, please
reference the troubleshooting guide on page 49.
Before applying voltage to power -up your swim spa, it is very important that you
understand the sequence of events that occur when the system is activated in
order that pumps can be primed efficiently and damage can be avoided.
1 . Turn on the breaker and test the swim side operation of the Ground -Fault
Circuit Interrupter (GFCI) breaker by pushing the small button. This should
automatically trip the swim spa�s circuit breaker.
DANGER: If this breaker does not trip, immediately call your electrician.
Do not use your swim spa!
Only if pushing this button successfully trips this circuit breaker should you
reset this breaker and proceed to the next step.
For swim spas with two electrical services to make sure to test both GFCls.
2. Turn on power to the swim spa. If your spa is equipped with two electrical
supplies, make sure that they are both turned on.
3. The swim spa will go through its priming mode. Go to the topside control
panel and follow the control instructions for your particular model swim spa
to activate the pumps. All swim spa first goes into a 6-minute Priming mode,
indicated by "Pr" message on display. Water heating is disabled during
priming. The purpose of the priming mode is to help insure that jet pumps
have been primed with water and ready to operate. It may be necessary in
some instances to bleed air from the lei pumps in your swim spa if after
priming mode the swim spa pumps run but do not move water. The pump
may have an air lock. To exit Priming mode and begin normal swim spa
operation, press "Up" or "Down" button. The circulation pump starts and
page 28
water flows through the jet returns.
4. After energized each of swim spa pump (see for details Topside controls and
Operation of each Spa model) you should hear the pump turn on high speed
and water circulating through one of River jet of swim spa.
Caution: If water is not flowing from the jets after 2 minutes, turn the
power off at the main panel and bleed air from the system (page
47). Turn the power on again. Sometimes momentarily turning
the pump off/on will help to prime. Only do this no more than 4
times.
5. If the water is running smoothly through the lines, open the air control valve
to the jets and you should see an increase in jet pressure. Check and adjust
the water and airflow of every river jet if necessary.
An air mixture intensifies the level of your current. Turn the air control valve
counterclockwise to increase the air mixture and clockwise to turn it off.
To minimize heat loss, close the air control valve when the swim spa is not
in use,
6. Repeat same procedure with the therapy pump located on spa side (see for
details Topside controls and Operation of each Spa model).
7. You should hear the pump turn on low speed and water start circulating
through therapy jets of spa.
8. If the water is running smoothly through the lines, open the air control valve
to the jets and you should see an increase in jet pressure. Check and adjust
the water and airflow of every river let if necessary.
An air mixture intensifies the level of your current. Turn the air control valve
counterclockwise to increase the air mixture and clockwise to turn it off.
To minimize heat loss, close the air control valve when the swim spa is not
in use.
9. Turn therapy pump on high speed (see for details Topside controls and
Operation of each Spa model). Verify the water flow circulating through the
therapy jets of spa. If the water is running smoothly through the lines, open
the air control valve to the jets and you should see an increase in jet
pressure. Check and adjust the water and airflow of every jet if necessary.
Each hydrotherapy jet in the spa side can be adjusted for massage intensity
and directional flow. Turn the outer jet dial counterclockwise to increase the
water volume and clockwise to turn it off. Pivot the angle of a jet to achieve
an optimal massage.
An air mixture intensifies the level of your massage. Turn the air control
valve counterclockwise to increase the air mixture and clockwise to turn it
Off.
To minimize heat loss, close the air control valve when the swim spa is not
in use.
10. Your swim spa water will heat approximately 1 0 per hour, on average. Times
may vary.
11. Adjust water chemistry according to the Water balancing section
Paae 29
40
Once your swim spa reaches 959F, use our Bromine Test Strips (not included)
and add the necessary chemicals (not included) to stabilize your water chemistry.
Turn Pump I on high speed before starting your tests to distribute chemicals
evenly. Wait 5 minutes between measurements to allow added chemicals to mix
thoroughly.
Important: Test the condition of your water in the following order:
1 . Total Alkalinity (80-120 ppm) — Use our Alkalinity Increaserto raise total
alkalinity and Alkalinity Decreaserto lower it. Low total alkalinity has little
buffering capacity making the pH erratic. High total alkalinity has too much
buffering capacity making the pH difficult to change.
2. pH (7.2-7.8) — Use Spa Up to raise the pH level and Spa Down to lower it.
Caution: A pH lower than 7.2 can harm the metal surfaces of your swim
spa and irritate your eyes and skin. A pH higher than 7.8 can
create calcium deposits (scaling) on the shell and equipment.
3. Hardness (150-400 ppm) — Add Increase Calcium until the proper level is
achieved. Unfortunately, there is no practical way to lower the native water
hardness other than using a different source of water when filling your swim
spa. Low hardness causes equipment corrosion and water foaming.
4. Sanitizer (3.0-5.0 ppm) — Use our Deluxe Bromine Ktto add Bromine until
the proper level is achieved. Neglected swim spa water can breed bacteria
and algae causing bather discomfort, skin rashes, and/or irritation.
Test
Range
�LT-17
didFAIRIN(VIV
M1,20
H
7.2-7.8
91501400§�M
Sanitizer
3.0-5.0 ppm
Table 2 - Recommended Ranges for Balanced Water
Note: Perform water balancing weekly and whenever you change water
(or when the swim spa is first filled) to ensure proper water condition.
M
-` �tr�
-00
00,
ML900 Topside Control Panel
US/Canada: used with controller PEI-2SWIM (wiring diagram, page 15)
Export: used with controller PGL2P3P4 (wiring diagram, pages 20, 21)
The topside control panel operates and programs your swim spa. Basic button
functions are described next.
When your swim spa is first time actuated, it will go into Priming mode, indicated
by "Pr". The Priming mode will last for less than 6 minutes(press 'Warm" or
"Cool" button to skip Priming Mode. And then the swim spa will begin to heat
and maintain the water temperature in the Standard mode.
Main Control Panel ML900
Legend:
Heat icon: Indicates different stages of heating
Jets icon: Spins fast on high speed; spins slow on low speed
Light icon: Light is on/off
F1, F2 indicators: Filter cycle 1 or 2 will be illuminated
PL, TL indicators: Locking Panel or Set Temperature will be illuminated
Temperature Up/Down Buttons
Press the Arrow "Warm" or Arrow "Cool" buttons once to display the set
temperature. Each time either button is pressed again, the set temperature will
increase or decrease depending on which button is pressed. After three seconds,
the LOD display will automatically display the current temperature the hot tub
water.
Mode Button
This button is used to switch between Standard, Economy and Sleep modes.
Press "Mode" to enter mode programming, press "Cool" through to desired mode
(LCD flashes until confirmed), then press "Mode" to confirm selection.
Page 31
For HELP, call 727.573.9611
Standard mode maintains the spa water to the set temperature. The "Std" icon
will display until the mode is changed.
Economy mode heats the spa water to the set temperature only during filter
cycles. The "Ecn" icon will display until mode is changed. Press "Jets 1" button
while in Economy mode to place the spa in "Standard -in -Economy mode," which
operates the same as Standard mode, and then reverts to Economy mode
automatically after one hour. During this time, a press of the "Mode" button will
revert to Economy mode immediately.
Sleep Mode heats the spa to within 20 OF (11 0 C) of the set temperature only
during filter cycles. "SLP" will display until mode is changed.
Standby Mode: Pressing "Warm Arrow Up" or "Cool Arrow Down" then "Jets2"
button will turn off all spa functions temporarily. This is helpful when changing
filter cartridges. Press any button to exit Standby mode.
Jets 1/Swim 1 Button
Press the "Jets 1 V'Swiml " button once to turn pump 1 on or off, and to shift
between low and high speeds. If left running, the low speed turns off after two
hours and high speed turns off after 15 minutes.
Jets 2-4/Swim 2-4 Buttons (if Equipped)
Press the "Jets 2-47"Swirn 24" buttons once to turn each of pumps 2-4 on or off.
If left running, the pumps 2-4 turns off after 15 minutes.
Stir/Swim All Button
Press the "Stir"/"Swim All" button once to turn pumps 2-4 on or off together. If
left running, the pumps 2-4 turns off after 15 minutes.
"Aux'T'Option" Button (if Equipped)
Press the "Aux" button once to turn blower on or off (if equipped). If left running,
the blower turns off after 15 minutes.
"Lights" Button
Press the "Lights" button to turn the spa light system on and off. The LED light
system is preprogrammed with an assortment of lighting effects. When you turn
Lights off and turn on again within five (5) seconds, it advances to the next effect
When you turn Light off for more than five (5) seconds, it remembers that last
effect you selected. The next time you turn on the Light will display the same
effect. The Light will automatically turn off after approximately four (4) hours.
Setting the Time
Once your spa has been properly connected the first time the "Time" icon
appearing on the screen and flashing. Press "Time" pad, then "Mode." Select the
hour by pressing "Warm" or "Cool" (each press changes time by 1 hour). Press
"Mode"pad again and select minutes by pressing"Warm" or"Cool" (each press
changes time by 1 minute). Press "Mode" pad to exit the time setting procedure
and enter the optional filter cycle programming. Press "Time" pad to exit
programming. The Time setting on this system is preserved in the event of power
Page 32
0
loss.
Invert Display
Press "Invert" button to change the direction of information on the display
Circulation Pump Operation (if equipped)
Your system is equipped with a circulation pump. The circulation pump provides
24-hour continuous water circulation and filtration. The Circulation pump turns
over the entire spa water capacity at a minimum of one time every hour
(depending on water capacity). It works like this: a dedicated, energy efficient
circulation pump constantly draws water from the spa, runs it through the filter 1
and the heater (heating only when necessary), then back to the spa. The ozone
output is on whenever the circulation pump is running. The Circulation pump will
turn off for 30 minutes at a time when the water temperature reaches 30F (1.50C)
above the set temperature (most likely this will happen in a very hot climate or
during summer).
Heater Operation
Your spa is equipped with an electrical heater. By setting your thermostat to the
desired temperature, your heater will automatically turn on and off as needed.
The temperature set point (set temperature) can be adjusted from 70OF to
1040F121OC-400C. To raise the set temperature press the "Warm Arrow Up"
button. To lower the set temperature, press the "Cool Arrow Down" button. The
startup temperature is set at 100OF/37.50C. The last measured temperature is
constantly displayed on the LCD. In Economy mode the heater heats the spa
water only during filter cycles. In sleep mode the heater heats the spa water to
within 20OF (11 OC) of set temperature only during filter cycles.
Filter Cycle Programming
Additional water circulation, filtration and ozonation (filter 2) added to spa system.
Two speeds pump I (Low) running during pre-programmed filtration cycles.
At the start of each filter cycle the blower (it equipped) will run for 30 seconds;
and the pump 1 (low) and, if equipped, pumps 2-4 (high) will run for 30 seconds
to prevent the spa water from becoming stagnant in the plumbing and air lines
and improve skimming action to remove debris and suspensions from the water
surface.
Your spa Game programmed from the factory with these defaults. The first filter
cycle is automatically activated at 8 a.m. and operates the pump 1 until 10 a.m.
The filter indicator icon on display will light when filter 1 cycle is running.
The second filter cycle is automatically activated at 8 p.m. and operates the
pump 1 until 10 p.m.. The filter indicator icon will light when filter 2 cycle is
running. To program custom filter cycle setting, press "Time"+"Mocle/Prog"
buffon+"Mode/Prog"+"Mode/Prog" within 3 seconds. The Program, Filter 1, Filter
2, and Start Time icons will appear on the display. Press"Warm" or"Cool" button
to choose the Filter 1 start time hour. Each press changes the start time by 5
minutes. Press "Mode/Prog" button to enter minutes. Press "Mode/Prog" to see
the Program, Filter 1, and End time icons. Adjust time as done above.
33
*1
Press "Mode/Prog" button to see the Program, Filter 2, and Start time icons.
Proceeds as above. Press "Mode/Prog" button to see the Program, Filter 2, and
End time icons. Adjust time as previously stated.. Press "Mode/Prog" button
again to enter the new filter time setting in system and display the current water
temperature. Press "Time" button at any time during this programming sequence
to save the values entered up to that point and exit programming.
Ozone System
Your spa is equipped with two ozone purification systems (only Deluxe models).
You will find that your spa water stays fresh and clear with significantly less
chemical sanitizer usage. You will be able to go longer between complete spa
draining. The ozone generator 1 operates in conjunction with the circulation
pump and ozone generator 2 running with two speeds pump I at low speed in
programming filtration cycles. Ozone generator 1 is on any time the circulation
pump is running.
Freeze Protection
If the temperature sensor detects a temperature drop to 440F (6.7'C) within the
heater, then the pump automatically activates to provide freeze protection. The
equipment stays on until four (4) minutes after the sensors detect that the spa
water temperature has risen to 450F (7.20C) or higher. In colder climates, an
optional additional freeze sensor may be added to protect against freeze
condition that may not be sensed by the standard sensors. Auxiliary Freeze
sensor protection acts similarly except with the temperature thresholds
determined by the switch and without a four (4) minute delay in turnoff. See your
dealer for details.
Locking the Panel
Press "Time", "Jets 1 " then "Warm Arrow Up" buttons within three (3) seconds.
When locked, the "PL" indicator light will light. All buttons are frozen except the
"Time" button. To unlock the panel, press "Time", "Jets 1" then "Cool Arrow
Down."
Locking the Temperature Setting
Press"Warm Arrow Up" or "Cool Arrow Down" then "Time," "Jets 1,"and 'Warm
Arrow Up" buttons within three (3) seconds to activate lock. When locked, the
"TL" indicator light will light when the set temperature is locked. To unlock the set
temperature, press"Warm Arrow Up" or"Cool Arrow Down" then "Time", "Jets 1,"
and "Cool Arrow Down."
Swim spa control power limitations
The swim spa and spa protected 60A GFCI (maximum spa load should not
exceed 48A).
The swim spa control deactivate heater if any High speed pump is running.
The swim spa control allows only three High speed pumps running at same time.
P.9e 34
0
Auxiliary panel AX20 (only If equipped)
Auxiliary panel AX20 typically installed on spa side. Press the "Jets" button once
to turn pump 1 on or off, and to shift between low and high speeds. If left running,
the low speed turns off after two hours and high speed turns off after 15 minutes.
Press the "Light" button to turn the spa light system on and off.
ML700 Top Side Control Panel
US/Canada: used with controller PEI-2SWIM (wiring diagram, page 15)
US/Canada: used with controller PEL2P3S2 (wiring diagram, page 16)
Export: used with controller PGL2P3P4(wiring diagram, pages 20, 21)
The topside control panel operates and programs your swim spa. Basic button
functions are descflbed next.
When your swim spa is first time actuated, it will go into Priming mode, indicated
by "Pr". The Priming mode will last for less than 6 minutes(press "Warm" or
"Cool" button to skip POming Mode. And then the swim spa will begin to heat
and maintain the water temperature in the Standard mode.
Jets 1 Button
Press the "Jets 1 " button once to turn pump 1 on or off, and to shift between low
and high speeds. If left running, the low speed turns off after two hours and high
speed turns off after 15 minutes.
Jets 2-3Buttons
Press the "Jets 2, 3" buttons once to turn each of pumps 2,3 on or off and shift
between low and high speeds. If left running, the low speed turns off after two
hours and high speed turns off after 15 minutes.
Light Button
Press the "Light" button to turn the spa light system on and off. The LED light
Pas. 35
call 727.
system is preprogrammed with an assortment of lighting effects. When you turn
Light off and turn on again within five (5) seconds, it advances to the next effect.
When you turn Light off for more than five (5) seconds, it remembers that last
effect you selected. The next time you turn on the Light will display the same
effect. The Light will automatically turn off after approximately four (4) hours.
Your system is equipped with a circulation pump. The circulation pump provides
24-hour continuous water circulation and filtration. The circulation pump turns
over the entire spa water capacity at a minimum of one time every hour
(depending on water capacity). It works like this: a dedicated, energy efficient
circulation pump constantly draws water from the spa, runs it through the filter 1
and the heater (heating only when necessary), then back to the spa. The ozone
output is on whenever the circulation pump is running. The Circulation pump will
turn off for 30 minutes at a time when the water temperature reaches 3OF (1.50C)
above the set temperature (most likely this will happen in a very hot climate or
during summer).
Heater Operation
Your spa is equipped with an electrical heater. By setting your thermostat to the
desired temperature, your heater will automatically turn on and off as needed.
The temperature set point (set temperature) can be adjusted from 70OF to
1040F/21OC-400C. To raise the set temperature press the 'Warm Arrow Up"
button. To lower the set temperature, press the "Cool Arrow Down" button. The
start up temperature is set at I 000F/37.50C. The last measured temperature is
constantly displayed on the LCD. In Economy mode the heater heats the spa
water only during filter cycles. In sleep mode the heater heats the spa water to
within 20OF (11 OC) of set temperature only during filter cycles.
Filter Cycle Programming
Additional water circulation, filtration and ozonation (filter 2) added to spa system.
Two speeds pump 1 (Low) running during pre-programmed filtration cycles.
At the start of each filter cycle the blower (if equipped) will run for 30 seconds;
and the pump 1 (low) and, if equipped, pumps 2-4 (high) will run for 30 seconds
to prevent the spa water from becoming stagnant in the plumbing and air lines
and improve skimming action to remove debris and suspensions from the water
surface.
Your spa came programmed from the factory with these defaults. The first filter
cycle is automatically activated at 8 a.m. and operates the pump 1 until 10 a.m.
The filter indicator icon on display will light when filter 1 cycle is running.
The second filter cycle is automatically activated at 8 p.m. and operates the -
pump 1 until 10 p.m.. The filter indicator icon will light when filter 2 cycle is
running. To program custom filter cycle setting, press "Time"+"Mode/Prog"
button+"Mode/Prog"+"Mode/Prog" within 3 seconds. The Program, Filter 1, Filter
2, and Start Time icons will appear on the display. Press "Warm" or "Cool" button
to choose the Filter I start lime hour. Each press changes the start time by 5
minutes. Press "Mode/Prog" button to enter minutes. Press "Mode/Prog" to see
the Program, Filter 1, and End time icons. Adjust time as done above.
Page 36
Press "Mode/Prog" button to see the Program, Filter 2, and Start time icons.
Proceeds as above. Press "Mode/Prog" button to see the Program, Filter 2, and
End time icons. Adjust time as previously stated.. Press "Mode/Prog" button
again to enter the new filter time setting in system and display the current water
temperature. Press "Time" button at any time during this programming sequence
to save the values entered up to that point and exit programming.
Ozone System
Your spa is equipped with two ozone purification systems (only Deluxe models).
You will find that your spa water stays fresh and clear with significantly less
chemical sanitizer usage. You will be able to go longer between complete spa
draining. The ozone generator 1 operates in conjunction with the circulation
pump and ozone generator 2 running with two speeds pump I at low speed in
programming filtration cycles. Ozone generator 1 is on any time the circulation
pump is running.
Freeze Protection
If the temperature sensor detects a temperature drop to 440F (6.70C) within the
heater, then the pump automatically activates to provide freeze protection. The
equipment stays on until four (4) minutes after the sensors detect that the spa
water temperature has risen to 45OF (7.20C) or higher. In colder climates, an
optional additional freeze sensor may be added to protect against freeze
condition that may not be sensed by the standard sensors. Auxiliary Freeze
sensor protection acts similarly except with the temperature thresholds
determined by the switch and without a four (4) minute delay in turnoff. See your
dealer for details.
Locking the Panel
Press "Time", "Jets I" then 'Warm Arrow Up" buttons within three (3) seconds.
When locked, the "PL" indicator light will light, All buttons are frozen except the
"Time" button. To unlock the panel, press "Time", "Jets I " then "Cool Arrow
Down."
Locking the Temperature Setting
Press Varm Arrow Up" or "Cool Arrow Down" then "Time," "Jets 1l," and "Warm
Arrow Up" buttons within three (3) seconds to activate lock. When locked, the
"TL" indicator light will light when the set temperature is locked. To unlock the set
temperature, press 'Warm Arrow Up" or"Cool Arrow Down" then "Time", "Jets 1,"
and "Cool Arrow Down."
Swim spa control power limitations
The swim spa and spa protected 60A GFCl (maximum spa load should not
exceed 48A).
The swim spa control deactivate heater if any High speed pump is running.
The swim spa control allows only three High speed pumps running at same time
Page 37
For
Auxiliary panel AX20 (only If equipped)
Auxiliary panel AX20 typically installed on spa side. Press the "Jets" button once
to turn pump 1 on or off, and to shift between low and high speeds. If left running,
the low speed turns off after two hours and high speed turns off after 15 minutes.
Press the "Light" button to turn the spa light system on and off.
MVP 260 Top Side Control Panel
US/Canada: used with controller VS50OZ (wiring diagram, page 18),
controller VS515Z (wiring diagram, page 19).
Export: used with controller GS50OZ (wiring diagram, page 23).
The topside control panel operates and programs your swim spa.
Basic button functions are described next.
When your swim spa is first time actuated, it will go into Priming mode, indicated
by "Pr". The Priming mode will last for less than 6 minutes(press "Warm" or
"Cool" button to skip Priming Mode. And then the swim spa will begin to heat
and maintain the water temperature in the Standard mode.
Initial Start Up
When your swim spa is first actuated, it will go into Priming mode, indicated by
"Pr." The priming mode will last for less than five minutes. Press'WARM" or
"COOL" to skip Priming Mode and then the swim spa will begin to heat and
maintain the temperature in "Standard Mode."
Warm/Cool Buttons (Set Temperatures between 80 IF - 104 OF / 26 OC - 40 OC)
The startup temperature is set at 100017/370C. The last measured temperature is
constantly displayed on the LCD and is current only when the pump has been
running for at least two minutes. To display the set temperature, press the
'WARM" or'COOL" button once. To change the set temperature, press the
'WARM" or 'COOL" button a second time before the LCD stops flashing. Each
press of the 'WARM" or "COOL" button will continue to raise/lower the set
Page 38
4
temperature. After three seconds, the LCD will stop flashing and display the
current swim spa temperature.
Jets Button
Press the "JETS" button once to activate the low speed of Pump 1. Press it a
second time to activate the high speed of Pump 1. Press it a third time to turn off
Pump 1. If left running, the high speed of Pump I automatically will turn off after
15 minutes and the low speed of Pump 1 automatically will turn off after 4 hours.
The low speed of Pump 1 may be active for at least two minutes every half hour
to detect the swim spa temperature and then to heat to the set temperature if
needed (depending on mode). When the low speed turns on automatically, it
cannot be deactivated from the panel, however the high speed may be activated.
Light
Press the "LIGHT" button once to turn on your swim spa lights. Press the LIGHT
button multiple times to cycle through the many available color patterns. Press
the LIGHT button again to turn off the LED light system. If left on, the lights
automatically turn off after 4 hours.
Mode
Your swim spa operating mode is changed by first pressing the 'WARM" or
"COLD" button, then pressing the "LIGHT" button.
Standard Mode is programmed to constantly maintain the desired
temperature. "Sf'will be displayed momentarily when you switch into
standard mode.
Economy Mode heats the spa to the set temperature only during filter
cycles. "Ed'will display solid when temperature is not current and will
alternate -with temperature when temperature is current.
Sleep Mode heats the swim spa to within 20*F/1 VC of the set
temperature only during filter cycles. "SL"will display solid when
temperature is not current and will alternate with temperature when
temperature is current.
Preset Filter Cycles
The first filter cycle begins six minutes after the swim spa is energized. The
second filter cycle begins 12 hours later. Filter duration is programmable for 2, 4,
6 or 8 hours — or for continuous filtration indicated by "FC'. The default filter time
is two hours.
To program filter cycles, press "WARM" or"COOL"and then "JETS." Press
'WARM" or"COOL" again to adjust to your desired setting. Press "JETS" again
to exit filter cycle programming.
The low speed of the 2-speed pump runs during filtration and the ozonator will be
enabled.
For 24 hour circulation systems the circulation pump and ozone generator run 24
hours. In hot environments the circulation pump will turn off for 30 minute
periods, except during filter cycles.
Page 39
Smart Winter Mode
If the system (sensor located inside heater) detects ambient
conditions below 449F/6.79C, it automatically enters the Smart
I Winter Mode for period of four minutes after it detects the swim spa
temperature has risen to 452F/7.2QC.
PurA
On/
VfEW
Ughts Indimtor Tempemture
Wolf Ughts D�
VL 600S. Top Side Control Panel
US/Canada: used with controller VS51 OSZ-AQ I O(wiring diagram, page 17),
Export: used with controller GS51 OSZ (wiring diagram page 22).
lard,
ep
to,
The topside control panel operates and programs your swim spa. Basic button
functions are described next.
When your swim spa is first time actuated, it will go into Priming mode, indicated
by "Pr". The Priming mode will last for less than 6 minutes(press'Warm" or
"Cool" button to skip Priming Mode. And then the swim spa will begin to heat
and maintain the water temperature in the Standard mode.
Initial Start Up
When your swim spa is first actuated, it Will go into Priming mode, indicated by
"Pr." The priming mode will last for less than five minutes. Press'WARM" or
"COOL" to skip Priming Mode and then the swim spa will begin to heat and
maintain the temperature in "Standard Mode."
Warm/Cool Buttons (Set Temperatures between SOOF - 1040F / 260C - 40'C)
PA
The startup temperature is set at 100OF/370C. The last measured temperature is
constantly displayed on the LCD and is current only when the pump has been
running for at least two minutes. To display the set temperature, press the
"WARM" or "COOL:'button once. To change the set temperature, press the
'WARM" or"COOL"button a second time before the LCD stops flashing. Each
press of the "WARM" or "COOL" button will continue to raise/lower the set
temperature. After three seconds, the LCD will stop flashing and display the
current swim spa temperature.
Jets Button
Press the "JETS" button once to activate the low speed of Pump 1. Press it a
second time to activate the high speed of Pump 1. Press it a third time to turn off
Pump 1. If left running, the high speed of Pump I automatically will turn off after
15 minutes and the low speed of Pump 1 automatically will turn off after 4 hours.
The low speed of Pump 1 runs when the "AUX" Pump 2 (if equipped) is on. It
may also active for at least two minutes every half hour to detect the swim spa
temperature and then to heat to the set temperature if needed (depending on
mode). When the low speed turns on automatically, it cannot be deactivated from
the panel, however the high speed may be activated.
Aux Button
Press the "AUX" button once to turn on Pump 2 (if equipped). Press it a second
time to turn off Pump 2. If left running, Pump 2 automatically will turn off after 15
minutes.
Light
Press the "LIGHT"button once to turn on your swim spa lights. Press the LIGHT
button multiple times to cycle through the many available color patterns, Press
the LIGHT button again to turn off the LED light system. If left on, the lights
automatically turn off after 4 hours.
Mode
Your swim spa operating mode is changed by first pressing the "WARM" or
"COLD" button, then pressing the "MODE" button,
• Standard Mode is programmed to constantly maintain the desired
temperature. "Std'will be displayed momentarily when you switch into
standard mode.
• Economy Mode heats the spa to the set temperature on/ycluring filter
cycles. "Ectf'will display solid when temperature is not current and will
alternate with temperature when temperature is current.
• Sleep Mode heats the swim spa to within 20OF/1 OOC of the set
temperature only during filter cycles. "SLP'will display solid when
temperature is not current and will alternate with temperature when
temperature is current.
41
Preset Filter Cycles
The first filter cycle begins six minutes after the swim spa is energized. The
second filter cycle begins 12 hours later. Filter duration is programmable for 2, 4,
6 or 8 hours — or for continuous filtration indicated by "F1 LC." The default filter
time is two hours.
To program filter cycles, press"WARM" or "COOL" and then "JETS." Press
'WARM" or "COOL" again to adjust to your desired setting, Press "JETS" again
to exit filter cycle programming.
The low speed of the 2-speed pump runs during filtration and the ozonator will be
enabled.
For 24 hour circulation systems the circulation pump and ozone generator run 24
hours. In hot environments the circulation pump will turn off for 30 minute
periods, except during filter cycles.
Smart Winter Mode
If the system (sensor located inside heater) detects ambient
conditions below 442F/6.7'C, it automatically enters the Smart
Winter Mode for period of four minutes after it detects the swim spa
temperature has risen to 45�F/7.29C.
Page 42
0
Figure 19 — VL600S Programming Summary
NOTE: FOR ALL SWIM SIDE EQUIPPED WITH MVP 260 PANEL:
Follow the above steps to set the filter cycle and water temperature.
To set the operating modes, follow the steps above except instead of
pressing "Mode" — press "LIGHT."
Page 43
0
Error Codes (All Spa Panels)
MESSAGE MEANING
ACTION REQUIRED
LL N
OHH The hot tub has shut down
Do not enter the water. Remove
HH from high heat detection.
the cover and allow the water to
One of the sensors
cool. Once cool, push any button.
detected 11 89F (489C) at
If the hot tub does not reset, turn
the heater.
off the GFCI and call service.
ICE Potential freeze condition
No action required. The pump will
IC detected (ice)
automatically operate regardless
of the hot tub status.
64
Tf
SnB Sensor B is not working
Check the sensor "B" plug
SB correctly. Hot tub is shut
connection to circuit board. The
down.
problem may appear temporarily
in an overheat situation and
disappear when the heater cools.
If the problem persists, contact
service.
HFL A substantial difference
Check water level in hot tub and
HIL between sensors was
add water if necessary. Be sure
detected (possible flow
that slide -valves are open. Make
problem).
sure the pump is primed and has
power. If the problem persists,
contact service.
Page 44
For HELP, call 727.573.9611
0
flow, or air bubbles
detected in the heater. Hot
tub is shut down for 15
minutes.
When the hot tub is first
activated, it goes into
Priming mode.
water if necessary. Be sure that
slide -valves are open. Make sure
the pump is primed and has
power. Press any button to reset
(automatically reset within 15
minutes). If the problem persists,
contact service.
The Priming mode runs for up to
four minutes and then the hot tub
begins to heat and maintain the
water temperature in Standard
SAH Sanitizer is high Remove hot tub cover and allow
Page 45
0
MESSAGE MEANING ACTION REQUIRED
CrC Firmware install problem Contact customer service if this
message appears on more than
one V
goweruh..
REMELOro
9F1 Could not trip GFCI Contact customer service and do
not use the hot tub.
HOt Pump was stuck on the Contact customer service and do
last time it was powered on not use the hot tub
Reminder Messages (Only for ML700, ML900 panels)
Message Frequency Action Required
rSA 7 days Test and ad ust sanitizer chemical levels.
E��gE&Rftb of �!-- 06�d I
rt9 30 da s Test & reset GFCI breaker.
rCO 180 days Clean and condition cover.
rCH 365 days Install new filter.
EAN, I I V
AMFNIIZWOUIIRI�19���
Special Operating Instructions
For swim spa equipped with waterfall features.
Turn on waterfall features by pressing "Jets" or "Spa!'button on top side panel to
energize one or two speed pump running this feature, turn "on -off" valve located
on top side of the swim spa and adjust water flow as you desire. Be sure you
adjust the water flow when pump running on highest speed to prevent water
splashing. With some swim spas the water feature is available only if the diverter
valve is set to position when swim spa water diverted to the water features. The
diverter valve also: located on top side of swim spa.
For swim spa equipped with River Jets (swim jets).
To turn on each jet press Swiml, 2, 3 or Jets 1, 2, 3 buttons. Each jets moves
300-350 GPM of water. To adjust water flow direction move 8" horizontal eyeball
nozzle up or down.
Page 46
For HELP, call 727.573.9611
0
13mijilill �6�4
Ready Marine stereo
MRD85i features DIVID Dock, Bluetooth and is an AM/FM/Sirius Satellite
Ready stereo with internal docking station for your digital music devices
(DIVID) like i-Pod, MP3 or Smartphone. Insert your digital music devices
and play your music. MRD85i is full featured waterproof marine stereo,
waterproof designed, engineered and optimized for spa use. With
adjustable backlight display type with flip down face design.SD Card
Reader available at the front. USB input available to play your music from a
USB Flash drive. Additional AUX Input available at the back. Wireless
Remote. Selectable EQ setup so you can select best audio setting for
particular speakers. Bluetooth enable.
NOTE: For instructions on how to operate your AM/FM audio system,
capabilities and features, see the manufacturer's Operational Manuals
(provided).
W&
W" lv,
Figure 20 — Optional MRDS51 Stereo
Page 47
For HELP, call 727Z73.961 I
Place the insulated cover on your swim spa. Keeping the cover in place anytime
the swim spa is not in use reduces the heating time and minimizes operating
costs. The time required for initial heat -up varies depending on the starting water
temperature, ambient temperature, and the capacity of your swim spa.
Figure 21 - Cover Callouts
1 . Lock -down tab
7.
Heat -sealed insulation
2. Double -stitched seams
S.
Chem ical-resistant vapor
3. Marine -grade cover material
barrier
4. Edge overlap material
9.
Polystyrene seam stoppers
5. Grip handle
10.
Reinforced edges
6. Aluminum channel
11.
Breathable underside material
Use the lock -down tabs to prevent access to
the swim spa by children and to prevent the
wind from lifting the cover off.
Figure 22 -
Lockdown Tabs
Sitting, standing, and snow buildup on the cover will break the cover. Dragging it
over rough surfaces will scuff or tear the fabric. Always lift by the handles or use
the optional cover lift device.
For HELP, call
Piece I Piece 2
93.6 Inches x 09's Inches
12MIS cm x 227.3 CM)
(212�3 CM x 227.3 cni)
.1.
:
r
Ar.:
Figure 23 — Swim Spa Cover Sections for "18" Models
NED303221=3211 U-M,
Is
Call our customer care center between 8 a.m. and 5 p.m. EST Monday through
Friday at 727.573.9611. Our representatives are eager to assist or you can get
parts and information online at -wvvw.HotTubParts.com.
Howdo leed air from my system?
When draining and refilling your swim spa, the pump may become air locked. Air -
locked pumps stop water from flowing in your swim spa and is easily resolved by
bleeding off the trapped a7ir. To do this:
1 . Turn off the GFCl breaker
2. Open the access panel below the topside control panel
3. Loosen a heater union until you hear the trapped air escape
4. Once water drips out. in a continuous stream, hand tighten the union until the
water stops leaking
5. Loosen the discharge union on Pump (if equipped)
6. Once water drips out in a continuous stream, hand tighten the union until the
water stops leaking
7. Turn on all pumps to make sure that there are no leaks
8. Put the access panels back on
9. Turn on the GFCl breaker
Page 49
For HELP, call 727.573.9611
Figure 24 - Bleeding Air
Pinnacle Spas will continue to provide service for your swim spa after your
warranty has expired via our customer care center at 727.573.9611.
Visit www.hottubparts.rom or call 877.530.PARTS.
Mid I clean my swim spa?
Use non-sudsing cleaners and non -oily polishes (Call). Our Citra Bright Spray
Cleaner and our Tub Rub cleaning pad quickly removes scum lines and helps
restore your shell's original beauty. Rinse all filters, covers, pillows, and surfaces
thoroughly with warm tap water. Our Filter Clean concentrated cleanser is a safe,
effective way to clean and re -use your filters and our Jet Clean plumbing
cleanser cleans the inside of all plumbing in your swim spa. Call 727.673.9611
to order these easy -to -use cleaning products.
How often should I drain my swim spa?
You should draln and refill your swim spa every 6-12 months depending on
usage. Every other time you drain and refill, you should also replace the filters
and wipe down the swim spa (Call).
How do I adjust my spa jets?
Simply turn the jets counterclockwise to open and clockwise to close. Be careful
not to overturn the jets, as damage can occur.
Caution: Do not turn off too many jets at the same time. This can create
backflow and possible damage to your swim spa! Do not attempt to
adjust the oval jets on the swim side of the unit.
Most spa jets are made removable and adjustable for customized hydrotherapy.
Do not attempt to remove the oval jets on the swim side of the unit.
MI
0
If a problem arises, you can check this list for a quick solution. If this does not
resolve your problem, please call our customer care center, at 727.573.9611.
Additional information is also available at pirmaclespas.com. You will need
your serial number to access this site.
Important — Most problems can be quickly resolved by resetting the
GFCI breaker. Try this first before proceeding.
M=bleshooting
PROBLEM CAUSE SOLUTION
Breaker trips Wiring error Load Neutral wire not connected to GFCI
(connected to Neu ral bus)
Wrong GFCI GFCI breaker is wronq size
Ozonator wet Remove tube from ozonator and allow 2
days to drV out
I
Leak Loose Check and hand -tighten unions at heater
connection or clamp on �ets
Drain open Close drain valve or replace cap
Low1no jet Air lock Bleed air from the system (page 47-48)
pressure Dirty filter Check and clean or replace filter
Closed jets Open all iets by turning CCW
Closed valves Open all T-handle shutoff valves on heater
and pumps
ACV open Close air control valves
Low water Fill swim spa 1 " above all jets
N.V
Nothing Breaker has Check and reset breaker. If problem
works tripped persists, check for loose electrical
connections. Check for Neutral wiring
error at GFC I.
Fuse blown Check for blown fuses inside of spa pack.
Page 51
27.573.9611
A
PROBLEM
C�USE
SOLUTION
Water does
Air lock
Bleed air from the system (page 47-48)
not flow
Closed jets
Open all jets by turning counterclockwise
ACV open
Close ak control valves
gow
ITINI 57-PI
51,
i 01 Al,
Water will not
Thermostat is
Check and reset to desired temperature
heat
set too low
Air open
Close air control valve
Dirty filter
Check and clean filter
Blown fuse
Check and replace fuse
Slide valve
Check and open all valves
closed
Cover off
Put the cover back on
Swim spa in
Press the Standby button and take out of
Economy
Economy
mode
Table 5
Page 52
For HELP, call 727.573.9611
Important — The warranty on your swim spa and equipment depends on proper
sanitation (see page 29). In addition, the following maintenance procedures must
be followed periodically.
0.121-1
Your cabinet is made from a polymer that combines the durability of plastic with
the beauty of simulated wood. To clean the cabinet, a mild soap and water
solution easily removes residue.
The 5-inch thick tapered cover on your swim spa is made from a weatherproof
marine -grade vinyl. It comes in two or three pieces, two that fold in half and one
small section for the middle. See page 42 for cover installation information. Your
cover will last much longer if you heed the following suggestions:
1 ) Don't drag the cover on the ground; wearing of the vinyl could easily develop
into a tear.
2) The insulating foam in your cover is not designed to hold the weight of a
person or an animal.
Important — Cracked foam in the cover is not covered under warranty! Do
not stand on it.
3) Occasionally clean the inside of your cover with our special All Purpose
Cleaner rinsed with warm water. (Using soap or vinyl cleaners on the inside
of your cover causes foamy water.) Call our order line at 727.573.9611 to
order our All Purpose Cleaner.
4) Our special Vinyl Cover Cleaner applied to the outside of the cover and
stitching once yearly will keep your cover looking better longer. Call our
order line at 727.573.9611 to order our special Vinyl Cover Cleaner.
5) Do not lift the cover by the safety straps, they are made to secure the tub to
the cabinet and may tear.
'Draining and Refillj6g
Drain Turn CCW Pull Out
kIn
Valve
Hose
Thmads
&N Iiio
RearBody
Hot Tub Panel
Figure 25 - Drain Operation
1) Turn off the GFCI breaker.
2) Remove swim spa cover and allow water to cool down.
Page 53
For HELP, call 727.573.9611
3) Select a safe, suitable drainage area capable of safely assimilating
approximately 2,000 gallons of water (7,571 liters) that may contain
unsanitary contaminants and chemical residue that could cause harm to
plants or grass.
4) Locate drain valve at base of the swim spa. Hold the rear body to prevent it
from turning, then loosen and remove the front cap.
5) Attach a garden hose to the exposed threads and route the hose downhill to
your drainage area.
6) Twist the drain fitting 1/3 turn counterclockwise to unlock the drain valve and
pull it outward to open completely. The water will drain by gravitational flow.
7) After the swim spa drains, perform steps 3-5 in reverse order to close the
drain prior to refilling swim spa.
8) Attach the garden hose to a thoroughly -flushed pre -filter (not included,
rinsed of all residual sediment) and refill your swim spa through the filtration
canister.
9) After refilling, turn on the GFCI breaker to the swim spa.
If the pump runs but no water flows, see page 47-48 to see how to bleed air from
the system.
The filters in your swim spa should be removed and cleaned every 2 weeks with
our special Filter Clean concentrated cleanser and typically replaced every 4-6
months (depending upon use). You can clean your filters with the water pressure
from the end of a garden hose then rinsed with warm water. This ensures that
the water is being filtered properly.
DO NOT USE BLEACH. We recommend having replacement filters on hand that
can be swapped between cleanings. Doing so enables you to quickly exchange
the dirty filters with clean ones and imniediately start your swim spa again. Call
our order line at 727.573.9611 to order replacement filters and our special Filter
Clean concentrated cleanser.
Hemove and clean the spa jets as needed using our special our Jet Glean
plumbing cleanser, water, and a cloth or soft -bristled brush. Call our order line
at 727.573.9611 to order our special our Jet Clean plumbing cleanser.
Drain the swim spa and clean the light lens as needed using an optical cloth and
an eyewear cleaning product specifically designed not to scratch optical
surfaces. If the back side of the lens is also dirty remove the rear panel, remove
the light from the holder, and clean in this same manner.
hemove ana ciean me neaarest pinows as neeaea using our unra tirigm.z>pray
Cleaner and our Tub Rub cleaning pad and rinsed thoroughly with warm
water. Call our order line at 727.573.9611 to order our Citra Bright Spray
Cleaner and our Tub Rub cleaning pad.
Sanitation level is influenced by two factors:
I . Filter Cycle (filtration) time
2. How much you use your swim spa each week
If your water chemistry and water clarity are all proper and your sanitation level is
still too low/high, you can adjust the sanitation intensity up/down by adding
more/less sanitizer a little at a time and testing the water again after two days.
Your Pinnacle Spas swim spa is designed to operate year rou
If you plan to leave your swim spa unused for long periods of
time in severely cold weather, you should winterize your swim
spa to avoid accidental freezing due to a power or equipment
failure.
We highly recommend that you have a swim spa professional winterize and
restart your swim spa.
WARNING: Damage from improperly winterizing or restarting your swim spa
is not covered under your warranty. You can call our customer care center, at
727.573.9611 for recommended service organizations to assist you in properly
winterizing your swim spa.
The acrylic surface of your swim spa should be cleaned with our Citra Bright
Spray Cleaner and our Tub Rub cleaning pad and thoroughly rinsed with
warm (not cold) water before refilling. Call our order line at 727.573.9611 to
order cleaners.
WARNING: NEVER use paint solvents, acids, acetone, benzene, lacquer
thinner, tolulene, xylene, or similar chemicals to clean your swim spa shell.
55
(6
,Water Management
Our chemical water purification system is a perfect match for your swim spa.
Depending on usage, the water in your swim spa should be changed every 6-12
months. Upon each change of water it is a good practice to wipe down the swim
spa.
If your water quality seems improper, increasing the time the swim spa filters the
water (see page 32) may clear up your problem.
Below are some answers to common water chemistry questions.
PH It is common to have pH fluctuations after adding chemicals to
your swim spa or after a party. Let your jets run and give your
water time to stabilize. 9 times out of 10, your pH will come back
into the 7.2-7.8 range on its own.
MILDEW
Mildew usually grows in the folds and seams of your cover and
on cover
then drips into your swim spa water causing cloudiness and/or
odor. Clean with our special Citra Bright Spray Cleaner and then
rinse the inside of your cover with clean warm water.
Foamy
Foam typically results from soap residue on your skin and hair, or
water
laundry detergent residue on clothing. Take a soapless shower
and rinse all clothing in warm water prior to bathing.
CLEAR
Your "source water" most likely has dissolved heavy metals.
green or
When this is the case, order our special Metal Gon metal
brown
remover. Using a pre -filter can remove these contaminants
water
before they get into your swim spa (see page 25).
CLOUDY
Algae can be resolved by adding a respected brand of algaecide.
green
water
CLOUDY
Although a normal condition immediately after filling that
white
dissipates after time, with stabilized water this is a visual
water
indication that the total alkalinity or pH or both are at improper
levels. Test your water weekly and maintain proper water
chemistry (see page 30).
ODOR
If your water develops an odor and/or cloudiness, clean your
and/or
cover and filters and try increasing the amount of time the swim
CLOUDY
spa filters per day by turning your filtration cycle time or duration
water
up.
HEAVY
After a period of heavy use, your swim spa may cloud. Shock
use
your swim spa with 2 ounces of non chlorine shock and wait 36
hours.
Page 56
For HELP, call 72T573.9611
IAQ 14/X'14 (M8/1208D)'
ova
sm mom
IMMOXIMMOU
OnITZSW
mAbuase&
4
Mvieb
39
AlrJ&
0
15MM
23010*
FRWW4M(WSlq
MIRW21
BMW FWM VACIAIdPftP
ZW4=
F-omww)
,
MIS
58
JAQ 14/X14 (1208-EX/1208D-EX) Export I
59
I
tk
'A
lain
2
Z�PL.. k4w,,. (Wawaqw:
w
21
�mo
w
�mbwy' awsa�
4
M4141�
2
2
25M4R,O�X)
LI
�t*"
—U
13
14
�-GDD(1295)
2
[Is
W47
to
v
I%
12
ZQ*I�M
2
mA
5,5?
tw
I�CNlqm
IS
u
M
208iQ
WA
lon, GM, muM
1
,fA
=mIw13IQ41w
I
Nm
��mtImsi
I
�I
m?"lzza
A
In
Mrsm
I
A
MIA
PW�
60
AQ 12/XI2 (1209/1209D) I I
sm Smc
6im mm
WBDIAQXfZI20M U
spaDtwom
OnUrdl*
MMtUFS—M—
—4
w3wm
34
AlrMs
Wft caomity (Usam
Ism4m
2100%
W115M
S05 �R*WVAVAJ
�XN(V_. WVH2)
vo�a�
GFUMP) - --
00
61
qo�m
MOV�
OY.
��4,Mmm(aq
2
IA-
Tote
V(Grk
2
20
MAI
wm.�
13
w
22M�
�10
Met m
F%,Q,
0
20511`.Ial�
�200-%
��Qw
5
40
mu�
2�010
rz,�
2
esm)-�-
ZRMZ��
��0044%a
.�(MW6NMF—
7460.�
Fo�
0
22202120�m
�10
R�
a
w
�sm
��Qfq
sees
Fen
2
%Ntl
�300
S�Wtt
A4 M.
S?3
0
21e��
4
mle;es�wt*
�Olw*
7
10
1310,1317, IeM4
Ltmmw.uv�
04,13349K
I
12
8=90
2
13
164
sp�
r (G.O*.)
4
16
�-Qwlm
wt;4A�
wttmv""4QI
2
is
W47
A.
V20
a
is
79OWC
31�*PWW
0
it
is
to
�I.W,000
W)
2
U5T
Ir
21
INOT
22
Q�A
M�
I
23
M56-3�
24
WPM
a
res. oaz;,31�
-TMWs
ff
I
NA
It". 3=u,ft3t"w
1 gp=
.
2
MA
0107.0�31�
gm mmmi
a
NA
50121
NA
0
NA
Offl.Z704
NA
IXMMM
w
I
MA
62
AQ 12/X12 1209-EX11209D-EX)
Export
No K M
C
OEM
MR
MA
KM
an
M31
lull
slum
AQ 16/Xl 6 (1211/1211 D)
0
MEMO
EEC=
mlcmz=�
I � � I � � i I � i � � I
mmommsmMMEN
I
0,
AQ 16/X16 (1211-EX/121ID7EX) Export
WNW
I
MT"J&
3?
24SWI24
1675M
SawsMUMM
SvkaZ2=lx=
--7ZW--W--v75F
2c
ruMom,
nfaz4wm
7SUFFIC
iD'
�-
2ztwq�m
4M.MbW.�XMM
7m
C�FbU.
ftm�
13IM317.1m
tm
—w-cmv2m
(Clxmj
4
1 1 wftsm��W�goi
.1
7--!9WRF=--
— .=wq��ZAZVAW
I
I ! "
so
ml,"ll
0
13
23
Mbl=m
INQIIGUM
25-
am
yw'�31ww
WA
ommEmawn.
lm=k3*ftm
�"Wft
wf,m-
ftw&.�b�
It
Gp.�
��K94FVIMUowftbw
68
I
I AQ 11 /Xl 1 (1 214/1214D)
Spa 8 0
Spa MDdel
1214DIAQ A 1. l2l4fAQ 11
Spa DImension
agrxl3rx5il
MunberOfSeats
6
Water Nrag Jets
64
WaterCapacity (USCA)
62COM
Dry Weight (LBSIKO)
12601545
Red We�ht (LBSn(G)
638VM
EW.tncal Rating VAC(AMPIM
240148/60
GFCI (AMP)
60
Lrr
0
-,B�uo
Car
7414
21X!22�00
at
'a
MON R-
2R
n22Z20*400.
a'
�Mbftmm-w 8,
2
23422�10
0
a"�
2$23Z�m
Sihls�Wft�.=
23412�10
'a
3m
1,
4
0
32V�JAWX.4�
m
25WI-�.
115
4D
2
io�l
to
29$4
4RQ
4
a -1
a 79 -1
4R
�24W=
0
cw. RI
.-at
ON=
Sla
��M.
7,452�10
:
2MY ,001-M
mo
mu�=.
�M�,Ww.w M
NOUN
ME
rlv�z
avzak�
mtaftLM�
26W-31�
s"ft.jmhtx.AA4Ql-(M ata�ak
292501�300
2
?
in
1315.4117.1m
25243�
Lw
-T2—
W3�
T�0.16"�
I
M$Vaa
�� 1
2
13
111"
Gp� 2r (G.P�j
4
14
2535�97�
I
1%
W0.12,03
0
1-0
ml?'"ta
a
17
M&S-Im"m
22W=��,
3
—is--
—31m3lmmm
7WTb—m� �*
io—
2!Z41407�
LW�C�IrIM.j
4
jim?
R.�b
2i
12&kiM.IM
1
23
2w"O"Od.
25�04�
=4
2$GC2�
7130, MaMll"140
3
Mt�014
m,�Otm,
0
6107.62kaf�
I
I
ZI.CM
60721
1
7�
W71.73119
M
78*6
WA
70
AQ11/Xll 1214-EX/1214D-EX)
Export
I&EXAGM
MIRW
WSW JW 66
IYW UP* WJW glym
pywvtpmG) 185m
FhdWdgaBSXG) %V=
SmtfW"(V=AMM
wam" I IEE W
1
4p
P�
m
WAI I.,
J8 "'Im
31
=2-2�:
Wft,.
—_191422=
w
�mc�
-7
IRO
W"� '.39
4
�-2�2W
0
M�la
40
"242-2��
4m
��m
4�
4
ir
Rl—
ii�
MR
=M2400-'m
23452��,*
"*57�14w.
SRO
"06
Gm
n=4004m
Wft
RIM,
2NS"�,
wnwDb.,
Fs
2
�o
1313,1317.1=.
2524�"W
Ll,hl
12
N�m.
2
13
1144
�Mf a1v
4
14
293"�r4wo
is
52747.12M4
7011.7016
="Mmi4�
la
3120.3120,3MO
19
4
21
1307
lamlm.lm
. i&A
�aq. �.31�w
wA
"". wo"Imal"Im
WA
M4.W241w�o
NA
W723
��Rmlmuf
I
ttA
Wr.7
�.Wwcw.�
I.,
WA
TOW,74M
I
553A
B.C�
72
I ES 14 (1303) 1
spa a
at
sp MGM
13nES14
Spa alwalon
GrllriFx6v
�Ubms
5
w6wim
14
Wax
Cpa* �
WHO
DrY WeW "SIKO)
2MIOM
FIWW*gQGj
LWOXWKOQ(VAVAMFVMP
M4M
QFCI MP)
so
73
41
c
Dit,
N
IM,
To
2=ZiiW�
2011s, JMM bwwd y
�Ek
0
21422�QMMM
C
2MU214w,
Jw
0
to
2am-2w-=,
3000 kdb"oI4
23432�tO
Omm"
r
r
NUMMMM—
Ra
muwm,
Mail .4"
%Sam, SB,
4
234W,W�QJQ
�*
to
tOCambeft
%
D
cm�u
ew
20547.101:=
�r P�J-k L-a"
*sMilic"W).
RO
20242-20�
2344�10
OWPOUIVAL twev
Onom"POW
To
samt �bwvu
-SBAWSB,
D
23452.00"10
C�Asm
arrm
m
29MQ�,
NOT mtiiitfv�
0
2340100"10
OrMa
=6�300-m,
2
M30-000,20
2!456410400�
21"1094M
a
W47N GAV
njopm%.PQ,"w
02�s�
5
10
1211S.700M
�Ugm
W
11
—UM—T�
o,.WJoN"M
I
12
251604)07�
Imset-ft.
.Qzw
I
Ti—
Sb� ft
rF"twa
0
14
54%
wlitwl
in.,
a
Ps
12minTliva
�ay.
ft duamm
I
I.Vaii
Iiiam
0
25pt,*Q�,W�
28"0�14'
Mail)
Tin 30DO15010 310.
1 so"O mlitir.
w Cwu;
174NO
YMwdl74OW;
SW4
S"I.MD
70611
mm
74
a
m
R
Paqe 75
cwi.q,ft
LOW
P"
"is"
�.a P)
�27ZIIRO,
213-wEZIR�
2=22,M.Mg,
fim
00EVOUL
2=ZaW�%
Wss
0
��Olo
Cm ma r
25- CjaLWWft W(EWSI�QJL
30G,MbWy *E2,
10
tKWt2-QQMIC
1.
'iF9NFlTl-4MT-
�ls
2=24"o.
ma.�h�y —.B48'M
4
2343�10
co�mu , ting
m4mli-mq,
�mw�o,
0
Ra
-suawsS,
0
�2�10
W5`FT—,QMm
m
�24M�O,
mom�yu -smasmo.
0
23402-OOMIC
w
25m4omlo
ms"N�%
�P� LED
2
"MOW200
17
1 �10.oa%
25OXIWS,200
I LWL tW�LED�
2
a
2104100,05a
R~Mllo. Wy(GFD
I
0
W41TOOGAV
znOlGPmsvwm
to
1210S�I`OMtA
twd"s Itm
1�
11
OM. 11822
T�16opmIVMMOD, (S�Xlm
1
12
=S��
I Ed S�q � ft
I
13
2100�6§13—
rlwmdfta� R�
a
14
SOSS
v
0
15
12W.1201.1268
I
Is
660480901;a
lwcwc"�
a
28pwd�.W� 1 25�dWWIA'
IIJ503D
C.,��
I
mt.di D,
7M 3ODMIPA 31�
1 epw ~, W ca". I
I
17�
�.ftd I I
QMPMP W �;
a
vm.=d;
s;o
I
77
cz
K m
IKM
4
#1
Dual Zone 18 (2022-EX), Export I
79
LWMI
SOON NONNI
NOMMOM0=00NO
NOR*
K3H��
NMI
smoolm
Wil if
alone
cm
C3
113
1=11010�-
Novi,
I
mil
ISwimmer 1'8'(2028)
am
81
o0i-
iA
I'M
2
m
l=2-200�0.
Wft�bWy
C.R!.. dog
a
m
�5-p�m
EEE Fft 9
m
2WNS24D�M
2
5
to
=4�
2344m"io
4ofthfw* W��U.
C�� ftq
0
2�TAQ,�,
29242-10�1
4��KWf44?,W�h
oa.mboo
52,
softlwbwy
a
2�W
M.�A%O.W,
3
10
uur�lalm 1312t, ws�
UamwmL=ZWG Dvpo�,
�1�.
12
mgw.�
2
2—
�PIRQW�w
a
,14
slc-SQ2�
is
=747.11592
is
MIT.1016
a
17
252awl-M
60
a
le
3IM312913,N
IM5- 'IT—,
0
iq
outm
cwiid�wixll
0
20
um
a
m
M?
lrli�ma..
I
Int
Q
IM, 125r, IM
1
23
2��912W
24
25�M
0
Too. 0=.3l"l4a
lwt�d ! wj
713% �IWM"140
1 S�d W�.Ilv �:
SW2%
eelba pak "oc;i
I
ssm
qIX
7�,78703
4A
5�
up c.�
VA —
------ MOW—
---f-
82
7sw Mimmer18 (2028-EX) Export
SOSM
spamm
zmmmmX
so mmaim
vwuw
swu�
vvat�
W&co"PW77
raKOPPOGI
KVIVOO WO)
RCD
smutwo
83
N�.Ufl n(Q)
2--
!A
Yale
—� t�
2
m
mv.oti�d,
�10
22V �1� L�D�(�Wddiddjl.
��tbwywevaasa.
a
m
�32�10
RQ
2W2�10
was�body
cc."" W,
6
to
2024��,
MU2.00"10
Mg
D
'm
2W42-M-M.
�2�fc
aftmbwy�,sa,
C... &a
0
30
MSFW-§EF-
mw-W�D.
2345M�010
WftmbW,
DO
29=��a.
lM45�10
6
n""19'm
7
250�10�01
MwMft W,
00.
a
a
64"n�v
w
9
10
121MMO&IMAIM,
1310,1317,1m,
Lightl0kal. LED 9�EP
3,1�0-3-
It
50�2
12
3WT
2
13
=tS
P� q.1
0
14
51�050
osq.�
3,
Is
�47111wa
�Y..a� r
1.1
to
7017.7018
T.1w. 1� P�
a
it
22VLolUmhWI.L�
0
is
3no.31n,3m
0
0
�m
"H��Lso
0
a
-
$456
—
v H�411.6
0
A
us?
I
It
lur
0
2-
Im,1207.120
I
M484)894W
4
I!SW2�
0
�tlololo;
7780, "00501m,3i"im
I S�d
3
A
�.6024.3104)ow
Qmp=p=SV4,dt
I
56?23
'A
ma"I
0071.7399
A
PER
4�1
Page 85
4�
M-
Warranty
*�L'Lff time Swim Spa Structural Warranty
iolrl'nacle Spas warrants the swim spa shell structure against the loss of water through the fiberglass laminate of the shell
ta sed by defects in materials and workmanship for as long as the original purchaser owns the swim spa. Contact manufacturer if
you have any questions concerning warranty issue's.
Five (5) Year — Swim Spa Surface Warranty
Pinnacle Spas Warrants the interior acrylic swim spa surface against blisters, cracks, or delaminating resulting from a defect
in the acrylic surface material for a period of five (5) years from the date of purchase, based on the following formula: Suggested
retail price divided by months covered (60), multiplied by months owned plus shipping = replacement cost.
Lifetime Manifold Plumbing Parts Warranty
Pinnacle Spas warrants the plumbing manifolds, fittings, and parts to be free of defects in materials or workmanship for as
long as the original purchaser owns the swim spa.
Two (2) Year — Limited Swim Spa Equipment Warranty
Pinnacle Spas warrants the electrical equipment and components to be free of defects in materials and workmanship for a
period of two (2) years on major swim spa components (electrical system, swim spa controls, motors) and two (2) years authorized
field service on these items. Ninety (90) day (Parts ONLY) Limited Warranty on all optional accessory items (optional cabinets,
fixtures, trim kits, skirts, CD & MP3 players, all other music and video devices, ozone, waterfall assembly, LED lighting, etc). All
perishable, cosmetic or owner serviceable items, swim spa cover, light bulb, light lenses, fuses, headrests, cabinet, filters, cover -lift,
swim spa drain, jet inserts, etc are warranted to be free of defects in materials and workmanship at the time of delivery. These
items may be covered by a manufacturer's warranty, which may have a longer duration than this Limited Warranty. Pinnacle
Spas may serve as an agent in presenting claims under the manufacturers' warranties, but disclaims any liability there under.
in the event Pinnacle Spas provides parts to replace an alleged defective part under warranty owner will be billed for the cost
thereof and credited, minus freight, upon both the defective part being returned to Pinnacle Spas and the manufacturer of
said part accepting warranty claim.
Warranty Performance
In the event of a suspected defect, under the terms of this Limited Warranty, notify manufacturer. Use all reasonable means to
protect the swim spa from further damage. A service representative will provide the technical labor only, to affect the repair subject
to the terms and conditions contained in this Limited War�anty. The service representative may assess reasonable travel charges.
Visits to simply diagnose, troubleshoot, or inspect problems are not covered under this Limited Warranty. If we determine that -
repairs are not feasible due to functional defect, we reserve the right to provide a replacement part or swim spa in lieu of repair.
We will replace with a part of value equal to the original purchase. In such event, owner is responsible for expenses including
removal, shipping, and re -installation of the existing or replacement hot tub. The replacement swim spa or part will carry the
balance of the original swim spa's warranty, if any. Either party's waiver of any breach or failure to enforce any of the terms or
conditions of the warranty shall not in anyway affect, limit or waive such party's right at anytime to enforce strict compliance with
every term and condition thereof.
Limitations and Exclusions
This Limited Warranty applies to swim spas sold after January 1, 200& This Limited Warranty takes effect from the date the unit was
originally purchased or six months from the date of manufacture whichever comes first. This Limited Warranty applies only to the
Original Purchaser and terminates with any transfer of ownership. This Limited Warranty does not apply to a swim spa used for any
commercial, rental, club purposes or for any swim spa used outside of the United States. The purchaser must establish the date of
purchase by dated sales invoice of delivery receipt.
This Limited Warranty does not cover damage resulting from abuse, misuse, or neglect including any installation, operation,
maintenance or use of the swim spa other than in accordance with the Owner's Manual of the swim spa. Damage caused by
operation of the swim spa at water temperatures outside the range of 32 degrees F. and 120 degrees F., damage caused by dirly,
clogged, or calcified filter cartridges, damage to the swim spa surface caused by improper use of chemicals or cleaning agents,
allowing un-clissolved water sanitizing chemicals to lie on the surface, damage caused by improper PH balance or other improper
water chemistry, damage caused by failure to provide even and sufficient support for the swim spa, are considered abuses and may
invalidate this Limited Warranty. Damaged caused by repairs or alterations performed by anyone other than an authorized service
representative is not covered. Failure caused by accidents, acts of God, nonstructural normal wear and tear, cosmetic blemishes and
other causes beyond our control are excluded.
The warranty is in lieu of all other warranties, expressed or implied, including implied warranties of merchantability and fitness for a
particular purpose. In no event shall manufacturer be liable for incidental or consequential damages.
DISCLAIMERS
The swim spa owner is required to provide unencumbered access to the swim spa for any warranty repair or inspection.
Manufacturer shall not be liable for loss of use of swim spa or other incidental or consequential costs, expenses or damages, which
may include, but are not limited to water damage, or the removal of a permanent deck or other customer fixture. Under no
circumstances shall we, or a ny of our representatives be held liable for injury to any person or damage to any property, however
arising., This warranty gives you specific legal rights and you may have other rights. No service company, or other party is authorized
to change, modify, or extend the terms of this Limited Warranty in any manner whatsoever. The jurisdiction and venue for any
litigatiorf arising with respect to the transaction evidenced by this warranty she 11 be the Circuit Court in a nd for Pinellas County,
Florida and Buyer hereby agrees to such jurisdiction and venue.
6101 45 Ih St. N.
St. Petersburg, FL 33714
727.573.9611
pinnaclespas.com