HomeMy WebLinkAboutNOAi10
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
AUTICE OF ACCEPTANCE (VOA
TAMKO Building Products, Inc. SCANNED
220 West 4h Street BY
Joplin, MO 64801 St. Lucie County
File C®k.'
IAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
Ov
— 00
SCOPE: SV vi%3 OC
This NOA is being issued under the applicable rules and regulations governing the use of Pnstmction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: TAMKO Roof Shingles
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal ofNOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No.15-0709.19 and consists of pages 1 through 6.
The submitted documentation was reviewed by Gaspar J Rodriguez
APPROVED
NOA No.: 15-1215.10
Expiration Date: 12/01/20
Approval Date: 05/26/16
Page 1 of 6
ROOFING ASSEMBLY APPROVAL
Category
Roofing
Sub -Category:
Asphalt Shingles
Materials:
Laminate
Deck Type:
Wood
SCOPE
This approves TAMKO's Heritage, Heritage Woodgate and Heritage Premium asphalt shingles, manufactured by
TAMKO Building Products, Inc., as described in this Notice of Acceptance and designed to comply with the Florida
Building Code High Velocity Hurricane Zones.
PRODUCT DESCRIPTION
Product
Heritage
Manufacturing Location # 1, 2, 3
Heritage Woodgate
Manufacturing Location # 1,3
Heritage Premium
Manufacturing Location # 1, 2, 3
MANUFACTURING LOCATIONS
1. Dallas, TX
2. Tuscaloosa, AL
3. Frederick, MD
EVIDENCE SUBMITTED
Test Agency
Underwriters Laboratories, Inc.
PRI Asphalt Technologies, Inc.
Dimensions
Test
_Product Description
Specifications
13 Y4" x 39 3/a"
TAS 110
Dimensional asphalt shingle.
13 %4" x 39 3/s"
TAS 110
Dimensional asphalt shingle.
13 Y44" x 39'/s"
TAS 110
Dimensional asphalt shingle.
PRI Construction Materials Technologies LLC
APPN0VE0
Test Identifier
Test Name/Report
Date
TAS 107 & UL 790
04CA44252
02/25/05
ASTM D3462
02NK33813
09/23/02
ASTM D 3462 & TAS 107
R2919 Letter
03/10/11
ASTM D3462
4789110543
08/26/14
TAS 107
02/19/15
ASTM E 108
08/26/14
ASTM D3161, Class F
4787043752
10/20/15
TAS 100
TAP-129-02-01
05/26/05
TAS 100
TAP-130-02-01
05/26/05
TAS 100
TAP-131-02-01
05/26/05
TAS 100
TAP-303-02-01
12/12/14
TAS 100
TAP-307-02-01
02/10/15
TAS 100
TAP-317-02-01
09/02/15
NOA No.: 15-1215.10
Expiration Date: 12/01/20
Approval Date: 05/26/16
Page 2 of 6
I,Da TIONS
I. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Shingles shall not be installed on roof mean heights in excess of 33 ft.
3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61 G20-3 of the Florida Administrative Code.
INSTALLATION
I. Shingles shall be installed in compliance with Roofing Application Standard RAS 115.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115.
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail `A', attached.
5. Nailing shall be in compliance with Details'B', attached.
LABELING
Shingles shall be permanently labeled with the manufacturer's name and/or logo, city and state of
manufacturing facility, and the following statement: "Miami -Dade County Product Control Approved" or with
the Miami -Dade County Product Control Seal as seen below:
MIAMI•DADE COUNTY
M M
BUILDING PERMIT REQUIIiEMENTS
As required by the Building Official or the applicable Building Code in order to properly evaluate the
installation of this system. This Notice of Acceptance on its own cannot be used to obtain a building permit.
MIAMFDADECOUNTY NOA No.: 15-1215.10
Expiration Date: 12MI/20
Approval Date: 05/26/16
Page 3 of 6
6-1/8"
MIAMIDAOE COUNTY
DETAIL A
HERITAGE, HERITAGE WOODGATE, AND HERITAGE PREMIUM
All dimensions an: in inches.
5TH COURSE
4TH COURSE
3RDCOURSE
2ND COURSE
29
1ST COURSE
i
NO
DETAIL B
HERITAGE SHINGLE
FIG. 1 FASTENING PATTERN
All dimensions are in inches
39-3/8"
7'/'�I7'W 73/e 7./. 73T 1.
F �I. SIG �IH
----•----
5-5/8"
NOA No.:15-1215.10
Expiration Date: 12/ol/2o
Approval Date: 0526/16
Page 4 of 6
DETAIL B (CONTINUED)
HERITAGE SHINGLE
FIG. 2ALTERNATE FASTENING PATTERN
HERITAGE SHINGLE
(TUSCALOOSA9 AL)
FIG. 3 ALTERNATE FASTENING PATTERN
HORIZONTAL NAIL SPACING IN ACCORDANCE WITH FIG.1 OR FIG. 2.
VERTICAL NAIL SPACING ALLOWED ANYWHERE WITHIN NAIL ZONE.
7-7
rha.i ClVtti
LOCATION
APPNOVED
Common Bond
NOA No.: 15-1215.10
Expiration Date: 12101t20
Approval Date: 05/26/16
Page 5 of 6
HERITAGE WOODGATE & HERITAGE PREMIUM SHINGLES
FIG. 4 FASTENING PATTERN
All dimensions are in inches
1° 7W 6'/:" 93/e 61/9 7YT 1°
CIE CIE `>IH
1
END OF THIS ACCEPTANCE
3
-114"
Exposure
MIAMbDAOECOUNW NOA No.: 15-1215.10
Expiration Date: 12/01/20
Approval Date: 05/26/16
Page 6 of 6
MIMI E
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE (NOA)
GAF
1 Campus Drive
Parsippany, NJ 07054
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida33175-2474
T (786)315-2590 F (786)31525-99
www.miamidade.gov/eeonomy.
IREVIEV4.0 NCE
E �omCn Kv
SCOPE: Uaeuuunw File Conv5r.
ti This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
SCANNFD
Sf BY
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product
Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County)
reserve the right to have this product or material tested for quality assurance purposes. If this product or
material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing
and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their
jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County
Product Control Section that this product or material fails to meet the requirements of the applicable
building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Gnventio'- nariBu► a oo stem o Woo
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and
following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no
change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in
the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any
product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply
with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors
and shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No. 14-1030.01 and consists of pages 1 through 27.
The submitted documentation was reviewed by Jorge L. Acebo.
o.• ,"
x iratiovDate. IHO
p toval Date: 0 71
LaXeAW_W
ROOFING SYSTEM APPROVAL
Category
Roofing
Sub -Category:
BUR
Material:
Fiberglass
Deck Type.•
Wood
Maximum Design
Pressure: -97.5 psf.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Description
GAFGLAS® Ply 4
39.37" (1 meter)
ASTM D2178
Smooth surfaced asphaltic ply sheet reinforced
Wide
with fiberglass mat.
Tri-Ply® Ply 4
39.37" (1 meter)
ASTM D2178
Smooth surfaced asphaltic ply sheet reinforced
Wide
with fiberglass mat.
GAFGLAS®
39.37" (1 meter)
ASTM D2178
Smooth surfaced asphaltic ply sheet reinforced
F1exPly'". 6
Wide
with fiberglass mat.
GAFGLAS11#75
39.37" (1 meter)
ASTM D4601
Smooth asphaltic base or base/ply sheet reinforced
Base Sheet
Wide
with fiberglass mat.
Tri-Ply®#75 Base
39.37" (1 meter)
ASTM D4601
Smooth asphaltic base or base/ply sheet reinforced
Sheet
Wide
with fiberglass mat.
GAFGLAS® 480
39.37" (1 meter)
ASTM D4601
Smooth asphaltic base or base/ply sheet reinforced
Ultima''Base Sheet
Wide
with fiberglass mat.
GAFGLAS®
39.37" (1 meter)
ASTM D4897
Smooth surfaced asphaltic perforated venting base
StratavenO
Wide
sheet reinforced with fiberglass mat.
Perforated Venting
Base Sheet
GAFGLAS® 39.37" (1 meter) ASTM D4897 Smooth surfaced asphaltic nailable venting base
Stratavent®Nailable Wide sheet reinforced with fiberglass mat. Bottom side
Venting Base Sheet surfaced with granules.
Ruberoid® 20 39.37" (1 meter) ASTM D6163 SBS polymer -modified asphalt base or
Smooth Wide anchor sheet reinforced with a fiberglass mat.
Ruberoid® Mop 39.37" (1 meter)
Smooth
wide
Ruberoid® Mop
39.37" (1 meter)
Smooth 1.5
wide
Ruberoid® Mop
39.37" (1 meter)
Plus Smooth
wide
Ruberoid® HW 25
39.37" (1 meter)
Smooth
wide
ASTM D6164 Smooth surfaced mop applied SBS base or
anchor sheet reinforced with a polyester mat.
ASTM D6164 Smooth surfaced mop applied SBS base or anchor
sheet reinforced with a polyester mat.
ASTM D6164 Smooth surfaced mop applied SBS base or
anchor sheet reinforced with a polyester mat.
ASTM D6163 Smooth surfaced torch applied SBS base or anchor
sheet reinforced with a fiberglass mat.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 2 of 27
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Dimensions
Specification
Ruberoid® HW
39.37" (1 meter)
ASTM D6164
Smooth
wide
GAFGLAS®
39.37" (1 meter)
ASTM D3909
Mineral Surfaced
Wide
Cap Sheet
Tri-Ply® BUR
39.37" (1 meter)
ASTM D3909
Granule Cap Sheet
Wide
Product
Description
Smooth surfaced torch applied SBS base or anchor
sheet reinforced with a polyester mat.
Granule surfaced asphaltic cap sheet reinforced
with fiberglass mat.
Granule surfaced asphaltic cap sheet reinforced
with fiberglass mat.
GAFGLAS® 39.37" (1 meter) ASTM D3909 Granule surfaced asphaltic cap sheet reinforced
EnergyCap' Wide with fiberglass mat. Cap sheet is factory coated
Mineral Surfaced with TOPCOAT EnergyCote' Elastomeric
Cap Sheet Coating.
Topcoat® Surface 5 or 55 gallons ASTM D6083 Solvent -based thermoplastic rubber
Seal SB sealant designed to protect and restore aged roof
surfaces and to increase roof reflectivity.
Topcoat® 1, 5 or 55 gallons ASTM D6083 Water -based elastomeric coating
Membrane
Topcoat® MB Plus 5 or 55 gallons Proprietary Water based, low VOC primer designed to block
asphalt bleed -through.
Topcoat® FireOuf' 5 or 55 gallons Proprietary Low VOC, water based fire barrier coating.
Fire Barrier Coating
VersaShield® Fire- 12" x 100' rolls ASTM D226 Non -asphaltic, fiberglass reinforced underlayment
Resistant Roof and/or fire barrier
Deck Protection
VersaShield® Solo'' 42" roll wide, 100 ASTM D146, Non -asphaltic, fire resistant fiberglass
Fire -Resistant Slip ft. D828, D4869, underlayment
Sheet D6757
Topcoat® 1, 5 gallons or TAS 139 Solvent -based elastomeric sealant.
FlexSeal' 1 qt. tube
NOA No.: 18-0919.07
rRAMFpnpecourrrr Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 3 of 27
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description
EnergyGuard" Polyiso Polyisocyanurate foam insulation
Insulation
EnergyGuard' Tapered
Polyiso Insulation
EnergyGuard" Ultra Polyiso
Insulation
EnergyGuard'" RA Polyiso
Insulation
EnergyGuard' RA Composite
Polyiso Insulation
EnergyGuard" RH Polyiso
Insulation
EnergyGuard' RH Tapered
Polyiso Insulation
EnergyGuard' RN Polyiso
Insulation
EnergyGuard' Perlite Roof
Insulation
Polyisocyanurate foam insulation
Glass -faced polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation with high
density fiberboard or permalite
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Perlite insulation board
EnergyGuard' Perlite Recover Perlite recover board
Board
Securock' Gypsum -Fiber Roof Gypsum board
Board
Securock' Glass -Mat Roof Glass faced gypsum board
Board
Structodek' High Density Fiber High density fiberboard
Board Roof Insulation
DensDeck' Prime Roof Board Gypsum board
DensDeck' Roof Board Gypsum board
Manufacturer
(With Current NOA)
GAF
GAF
GAF
GAF
GAF
GAF
GAF
GAF
GAF
GAF
United States Gypsum Corp.
United States Gypsum Corp.
Blue Ridge Fiberboard, Inc.
Georgia-Pacific Gypsum LLC
Georgia-Pacific Gypsum LLC
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 4 of 27
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
(With Current NOA)
1.
Drill-Tec"" #12 Fastener
Phillips head, modified
#12 x 8" max.
GAF
buttress thread, pinch point,
length, #3
carbon steel fastener for use
Phillips head.
in steel or wood decks. With
CR-10 coating. Available
with a pinch point or drill
point.
2.
Drill-Tec"° #14 Fastener
Truss head, self -drilling,
#14 x 16"
GAF
pinch point, high thread
max. length,
fastener for use in steel, wood
43 Phillips
or concrete decks.
head.
3.
Drill -Tee" ASAP 3S
Drill-Tec' #12 Fastener with
See
GAF
Drill-Tec'" 3" Standard Steel
components
Plate.
4.
Drill-Tec' 3" Steel Plate
Round Galvalume® steel
3" Round
GAF
stress plate with reinforcing
ribs and recessed for use with
Drill-Tec7' fasteners.
5.
Drill-Tec'" 3" Standard Steel
Galvalume® coated steel
3" Round
GAF
Plate
stress plate for use with
approved Drill-Tec'°'
fasteners.
6.
Drill-Tec'" AccuTrac® Flat
A2-SS aluminized steel plate
3" square;
GAF
Plate
for use with Drill-Tec"'
.017" thick
fasteners.
7.
Drill-Tec'" AccuTrac®
Galvalume® steel plate with
3" square;
GAF
Recessed Plate
recess for use with Drill-
.017" thick
Tee fasteners.
8.
Drill-Tec 3 in. Ribbed
Round Galvalume® plated
3" Round
GAF
Galvalume Plate (Flat)
steel stress plate with
reinforcing ribs for use with
Drill-Tec'" fasteners.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 5 of 27
EVIDENCE SUBMITTED:
Test A9enCV
Test Identifier
Description
Date
Factory Mutual Research Corp.
3014547
4470
05/22/03
3029832
4470
05/11/07
3033135
4470
11/24/08
3034312
4470
04/09/09
3036980
4470
08/14/09
3038278
4470
11/18/11
3040738
4470
11/16/10
3041769
4470
05/26/11
3042887
4470
11/14/11
3042905
4470
01/10/12
3046081
4470
02/13/13
3046388
4470
09/24/12
3047636
4470
08/08/13
ODOA8.AM
4470
07/09/99
OD IA8.AM
4470
07/29/94
OY9Q5.AM
4470
04/01/98
1B9A8.AM
4470
09/04/97
2B8A4.AM
4470
07/02/97
3B9Q 1.AM
4470
01/08/98
3D4Q2.AM
4470
05/30/97
797-03221-267
4470
09/27/07
797-03825-267
4470
07/21/08
797-10228-267
4470
01/23/15
UL LLC
R1306
UL 790
08/21/18
PRI Construction Materials
GAF-122-02-01
TAS 139
05/07/06
Technologies, LLC
GAF-270-02-02
ASTM D226
11/15/10
GAF-276-02-01Rev
ASTM D6083
12/16/10
GAF-276-02-02
ASTM D226
11/15/10
GAF-306-02-01
ASTM E96
07/07/11
GAF-314-02-01
ASTM D2178
08/23/11
GAF-315-02-01
ASTM D2178
08/23/11
GAF-369-02-01
ASTM C1289
10/22/12
GAF-417-02-01
ASTM C1289
05/28/13
GAF464-02-01
ASTM C1289
10/22/12
GAF464-02-01
ASTM C1289
02/06/14
GAF499-02-01
ASTM D6083
03/12/14
GAF-500-02-01
ASTM D6083
03/12/14
GAF-549-02-01
TAS 114
08/08/14
GAF-549-02-02
TAS 114
08/08/14
GAF-559-02-01
TAS 117(B)
09/30/14
GAF-559-02-04
ASTM D 1876
10/01/14
GAF-559-02-05
ASTM D 1876
10/15/14
GAF-559-02-06
TAS 114(H)
10/02/14
GAF-559-02-07
ASTM D 903
10/02/14
GAF-559-02-08
ASTM D 903
10/02/14
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 6 of 27
EVIDENCE SUBMITTED: (CONTINUED)
Test Aeencv
Test Identifier
Description
Date
PRI Construction Materials
GAF-559-02-09
ASTM D 903
10/02/14
Technologies, LLC
GAF-559-02-11
TAS 114
10/14/14
GAF-559-02-12
TAS 114
10/14/14
GAF-559-02-13
TAS 114
10/15/14
GAF-559-02-14
TAS 114
10/15/14
GAF-559-02-15
TAS 114
10/15/14
GAF-559-02-16
TAS 114
10/15/14
GAF-559-02-18
TAS 114
10/15/14
GAF-559-02-19
TAS 114
04/16/15
GAF-628-02-01
ASTM C1289
05/31/16
IRT of S. Fl.
02-005
TAS 114
01/18/02
02-014
TAS 114
03/22/02
Trinity I ERD
C8500SC.11.07
TAS 117
11/30/07
G30250.02.10-3-R2
ASTM D3909
06/03/15
G31360.03.10
ASTM D6164
03/31/10
G33470.01.11
ASTM D6164
11/16/11
G34140.04.11-2
ASTM D6163
04/25/11
G34140.04.11-4-R2
ASTM D6401
06/04/15
G34140.04.11-5-R3
ASTM D4897
06/04/15
G36780.07.11-RI
4470-TAS 114
07/18/11
G40630.01.14-1
ASTM D6163
01/06/14
G40630.01.14-2A
ASTM D6164
01/07/14
G40630.01.14-2A-1-Rl
ASTM D6164
04/10/14
G43610.01.14
ASTM D3909
01/22/14
G6850.08.07-1
ASTM D3909
08/13/07
SC6870.08.14-R1
ASTM D3909
09/04/14
SC9700.08.15-R1
ASTM D2178
8/31/2015
SC10680.05.16
ASTM D6163
5/10/2016
SC13105.03.17-RI
ASTM D6164
3/23/2017
Dynatech Engineering Corporation
94482.02.95-1
TAS 114
09/01/95
Atlantic & Caribbean Roof
11-053
TAS 114
08/12/11
Consultants, LLC
NOA No.: 18-0919.07
MIAMMAD, C01 Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 7 of 27
APPROVED ASSEMBLIES
Membrane Type:
BUR
Deck Type 1I:
Wood, Insulated
Deck Description:
Min. 19/32" or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type A(1):
All insulation layers are adhered, to a mechanically attached anchor sheet. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier:
Topcoat® FireOut' Fire Barrier Coating, VersaShield® Fire -Resistant Roof Deck Protection,
(optional)
VersaShield® Solo' Fire -Resistant Slip Sheet, DensDeck® Roof Board, SecurocP Glass -
Mat Roof Board or Securock' Gypsum Fiber Roof Board installed per manufacturer's
installation instructions.
Anchor sheet:
GAFGLAS® #80 Ultima'" Base Sheet, GAFGLAS® Stratavent® Nailable Venting Base
Sheet or Ruberoid® 20 Smooth mechanically fastened as described below.
Fastening
GAFGLAS® Ply 4, GAFGLAS® Flex Ply'" 6, GAFGLAS® #75 Base Sheet or any of above
Option ft
anchor sheets attached to deck with approved annular ring shank nails and tin caps at a
fastener spacing of 9" o.c. at the lap staggered and in two rows 18" o.c. in the field.
Not for use with DensDeck or Securock Fire Barrier
(Maximum Design Pressure —45 psf. See General Limitation #9)
Fastening
GAFGLAS® Ply 4, GAFGLAS® FlexPly' 6, GAFGLAS® #75 Base Sheet or any of above
Option #2:
anchor sheets attached to deck with Drill-Tec7' #12 Fastener, Drill-Tec' #14 Fastener and
Drill-Tec"" 3" Steel Plate, Drill-Tec'" AccuTrac® Flat Plate or Drill -Tee AccuTrac®
Recessed Plate 12" o.c. in 3 rows. One row is in the 2" side lap. The other rows are equally
spaced approximately 12" o.c. in the field of the sheet.
(Maximum Design Pressure —45 psf. See General Limitation #9)
Fastening
GAFGLAS® FlexPly'" 6, GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet or any of
Option #3:
above anchor sheets attached to deck with approved annular ring shank nails and tin caps at
a fastener spacing of 9" o.c. at the 4" lap staggered and in two rows 9" o.c. in the field.
Not for use with DensDeck or Securock Fire Barrier
(Maximum Design Pressure —52.5 psf. See General Limitation #7)
Fastening
Any of the above anchor sheets attached to deck with approved 1'/4" annular ring shank nails
Option 94:
and inverted 3" steel plate at a fastener spacing of 9" o.c. at the 4" lap and in two rows
staggered with a fastener spacing of 9" o.c. in the center of the membrane.
Not for use with DensDeck or Securock Fire Barrier
(Maximum Design Pressure —60 psf. See General Limitation #7)
Fastening
GAFGLAS® #75 Base Sheet or any of above anchor sheets attached to deck with Drill-Tec""
Option #5:
#12 Fastener, Drill-Tec' #14 Fastener and Drill -Tee 3" Steel Plate, Drill -Tee AccuTrac®
Flat Plate or Drill-Tec'" AccuTrac® Recessed Plate 12" o.c. in 4 rows. One row is in the 2"
side lap. The other rows are equally spaced approximately 9" o.c. in the field of the sheet.
(Maximum Design Pressure —45 psf. See General Limitation #9)
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 8 of 27
Fastening (Continued) Any of above anchor sheets attached to deck approved annular ring shank nails and 3"
Option #6: inverted Drill-Tec' insulation plates at a fastener spacing of 9" o.c. at the 4" lap staggered in
two rows 9" in the field. Not for use with DensDeck or Securock Fire Barrier
(Maximum Design Pressure —60 psf. See General Limitation 97)
Fastening GAFGLAS' #75 Base Sheet or any of above anchor sheets attached to deck with Drill-Tec''
Option #7: #12 Fastener or Drill-Tec' #14 Fastener and 3" Drill-Tec'" 3" Steel Plate, Drill-Tec'
AccuTrac® Flat Pate or Drill-Tec' AccuTrac' Recessed Plate 8" o.c. in 4 rows. One row is
in the 2" side lap. The other rows are equally spaced approximately 9" o.c. in the field of
the sheet.
(Maximum Design Pressure —45 psf. See General Limitation #9)
One or more layers of any of the following insulations.
Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ftz
EnergyGuard'" Polyiso Insulation, EnergyGuard' Ultra Polyiso Insulation, EnergyGuard RH Polyiso
Insulation, EnergyGuard'' RA Polyiso Insulation, EnergyGuard' RA Composite Polyiso Insulation
Minimum 1" thick N/A N/A
EnergyGuard' Perlite Recover Board, DensDeck® PrimeRoof Board
Minimum %:" thick N/A N/A
EnergyGuard" Perlite Roof Insulation
Minimum %" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 lbs./100 It'. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Composite insulation panels may be used as a top layer placed with the
-polyisocyanurate side facing down. GAF requires either a ply of GAFGLAS' Stratavent® Perforated Venting
Base Sheet laid dry or a layer of EnergyGuard'' Perlite Roof Insulation or wood fiber overlay board on all
polyisocyanurate applications.
Base Sheet: (Optional) Install one ply of GAFGLAS' #75 Base Sheet, Tri-Ply® #75 Base Sheet,
GAFGLAS® #80 Ultima'" Base Sheet, Ruberoid® Mop Smooth, Ruberoid® Mop Smooth
1.5, Ruberoid® Mop Plus Smooth or Ruberoid® 20 Smooth, Ruberoid® HW Smooth or
Ruberoid® HW 25 Smooth directly over the top layer of insulation. Adhere with any
approved mopping asphalt applied within the EVT range and at a rate of 2040 lbs./sq.
applied in accordance with manufacturer's instructions. (see General Limitation #4).
OR
GAFGLAS® Stratavent® Perforated Venting Base Sheet loose -laid dry (not for use with
perlite top layer insulation or composite polyiso top layer insulation).
Ply Sheet: One or more plies GAFGLAS® Ply 4, Tri-Ply' Ply 4, GAFGLAS® FlexPly'" 6 or
GAFGLAS' #80 Ultima Base Sheet adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-401bs./sq. installed per manufacturer's installation
instructions.
Cap Sheet: (Optional) One ply of GAFGLAS' Mineral Surfaced Cap Sheet, Tri-Plyl BUR Granule
Cap Sheet or GAFGLAS' EnergyCap' Mineral Surfaced Cap Sheet adhered in a full
mopping of approved asphalt applied within the EVT range and at a rate of 2040 lbs./sq.
installed per manufacturer's installation instructions.
NOA No.: 18-0919.07
MAMMADE COUNTY Expiration Date: 11/04/23
FIX =sp
Approval Date: 11/08/18
Page 9 of 27
Surfacing: Optional on granular surfaced membranes; required for smooth membranes. Chosen
components must be applied according to manufacturer's application instructions. All
coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at I to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
3. Fiber Aluminum Roof Coating.
Maximum Design
Pressure: See Fastening Options.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 10 of 27
Membrane Type:
BUR
Deck Type 1I:
Wood, Insulated
Deck Description:
Min. 15/32" thick or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type A(2):
All insulation layers are adhered, to a mechanically attached anchor sheet. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier:
Topcoat® FireOut' Fire Barrier Coating, VersaShield® Fire -Resistant Slip Sheet or
(optional)
VersaShield® Solo' Fire -Resistant Slip Sheet installed per manufacturer's installation
instructions.
Anchor sheet:
GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet, Ruberoid® 20 Smooth or
GAFGLAS® Strataven& Venting Nailable Base Sheet is secured as described below.
Fastening
Miami -Dade County Approved min. 12 ga. Annular ring shank nails and min. 1-5/8 in.
Option #1:
diameter tin caps are spaced 8 in. o.c. in the min. 4 in. wide anchor sheet side laps and 8
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —45 psf. See General Limitation #7)
Fastening
Miami -Dade County Approved min. 12 ga. Annular ring shank nails and min. 1-5/8 in.
Option #2:
diameter tin caps are spaced 6 in. o.c. in the min 4 in. wide anchor sheet side laps and 6
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill -Tee #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill -Tee
Option #3:
AccuTrac® Flat Plates or Drill-Tec'' 3 in. Ribbed Galvalume Plate (Flat) are spaced 16
in. o.c. in the min. 4 in. wide anchor sheet side laps and 16 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill -Tee #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec'
Option #4:
AccuTrac® Flat Plates or Drill -Tee' 3 in. Ribbed Galvalume Plate (Flat) are spaced 12
in. o.c. in the min 4 in. wide anchor sheet side laps and 12 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure: —60 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec"" 3 in. Standard Steel Plates, Drill-Tec"'
Option #5:
AccuTrac® Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 8 in.
o.c. in the min. 4 in. wide anchor sheet side laps and 8 in. o.c. in the field of the sheet in
three staggered rows.
(Maximum Design Pressure: —75 psf. See General Limitation #7)
One or more layers of any of the following insulations.
Base Insulation Layer
Insulation Fasteners Fastener
(Table 3) Density/ft2
EnergyGuard'" Polyiso Insulation, EnergyGuard' Tapered Polyiso Insulation, EnergyGuard' Ultra Polyiso
Insulation, EnergyGuard"'
RH Polyiso Insulation, EnergyGuard"' RH Tapered Polyiso Insulation
Minimum 1" thick
N/A N/A
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 11 of 27
Top Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ft'
EnergyGuard' Perlite Roof Insulation
Minimum'/," thick N/A N/A
Structodek® High Density Fiberboard Roof Insulation
Minimum''%" thick N/A N/A
Securock® Gypsum -Fiber Roof Board, DensDeck® Prime Roof Board
Minimum''/<" thick N/A N/A
Note: All insulation shall be adhered in a full mopping of approved hot asphalt within the EVT range and at a
rate of 2040 lbs./100 ft'. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet (Optional): GAFGLAS® #75 Base Sheet, Tri-Ply' #75 Base Sheet, Ruberoid® 20 Smooth adhered in
a full mopping of hot asphalt applied at 2040 lbs./sq. installed per manufacturer's
installation instructions.
Ply Sheet: When optional base sheet and/or cap sheet is present:
Two or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6 adhered
in a full mopping of hot asphalt applied at 20-40 lbs./sq. installed per manufacturer's
installation instructions.
When optional base sheet and/or cap sheet is not present:
Three or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6
adhered in a full mopping of hot asphalt applied at 20-40 lbs./sq. installed per
manufacturer's installation instructions.
Cap Sheet (Optional):
GAFGLAS® Mineral Surfaced Cap Sheet, Tri-Ply® BUR Granule Cap Sheet or
GAFGLAS® EnergyCap' Mineral Surfaced Cap Sheet adhered in a full mopping of hot
asphalt applied at 20 — 40 lbs./sq. installed per manufacturer's installation instructions.
Surfacing:
Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1.
Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2.
Topcoat® Membrane or Topcoat® Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
3.
Aluminum Fiber Roof Coating.
Maximum Design
Pressure:
See fastening options above.
MIAMWADE COUNTY
....T6 1
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 12 of 27
Membrane Type:
BUR
Deck Type 11:
Wood, Insulated
Deck Description:
Min. 15/32" thick or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type A(3):
All insulation layers are adhered, to a mechanically attached anchor sheet. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier:
Topcoato' FireOut' Fire Barrier Coating, VersaShield® Fire -Resistant Slip Sheet or
(optional)
VersaShield® Solo' Fire -Resistant Slip Sheet installed per manufacturer's installation
instructions.
Anchor sheet:
GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet, Ruberoid® 20 Smooth or
GAFGLAS® Stratavent® Venting Nailable Base Sheet is secured as described below.
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #1:
diameter tin caps are spaced 8 in. o.c. in the min. 4 in. wide anchor sheet side laps and 8
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —45 psf. See General Limitation #7)
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #2:
diameter tin caps are spaced 6 in. o.c. in the min 4 in. wide anchor sheet side laps and 6
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure. —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec"' 3 in. Standard Steel Plates, Drill-Tec'
Option #3:
AccuTrae Flat Plates or Drill -Tee 3 in. Ribbed Galvalume Plate (Flat) are spaced 16
in. o.c. in the min. 4 in. wide anchor sheet side laps and 16 in. o.c. in the field of the
sheet in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill -Tee
Option #4:
AccuTrac® Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 12
in. o.c. in the min 4 in. wide anchor sheet side laps and 12 in. o.c. in the field of the
sheet in two staggered rows.
(Maximum Design Pressure. —60 psf. See General Limitation #7)
Fastening
Drill -Tee #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill -Tee
Option #5:
AccuTrac® Flat Plates or Drill -Tee' 3 in. Ribbed Galvalume Plate (Flat) are spaced 8 in.
o.c. in the min. 4 in. wide anchor sheet side laps and 8 in. o.c. in the field of the sheet in
three staggered rows.
(Maximum Design Pressure. —75 psf. See General Limitation #7)
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 13 of 27
One or more layers of any of the following insulations
Base Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ft2
EnergyGuard' Polyiso Insulation, EnergyGuard"' Tapered Polyiso Insulation, EnergyGuard"' Ultra Polyiso
Insulation, EnergyGuard' RH Polyiso Insulation, EnergyGuard'' RH Tapered Polyiso Insulation
Minimum 1" thick N/A N/A
Top Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ft2
EnergyGuard' Perlite Roof Insulation
Minimum'/<" thick N/A N/A
Structodek® High Density Fiberboard Roof Insulation
Minimum''/:" thick N/A N/A
Securock® Gypsum -Fiber Roof Board, DensDeck' Prime Roof Board
Minimum'/4" thick N/A N/A
Note: All insulation shall be adhered in a full mopping of approved hot asphalt within the EVT range and at a
rate of 2040 lbs./100 It. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: Ruberoid' 20 Smooth adhered in a full mopping of hot asphalt applied at 20401bs./sq.
Cap Sheet: GAFGLAS' Mineral Surfaced Cap Sheet, Tri-Ply' BUR Granule Cap Sheet or
GAFGLAS' EnergyCap' Mineral Surfaced Cap Sheet adhered in a full mopping of hot
asphalt applied at 20 — 40 lbs./sq. installed per manufacturer's installation instructions.
Surfacing: Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat' Membrane or Topcoat' Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat' MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat' Membrane applied at 0.5 to 0.75 gal./sq.
3. Aluminum Fiber Roof Coating.
Maximum Design
Pressure: See fastening options above.
NOA No.: 18-0919.07
MLA nonne counm Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 14 of 27
Membrane Type:
BUR
Deck Type 1I:
Wood, Insulated
Deck Description:
Min. 15/32" thick or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type A(4):
All insulation layers are adhered, to a mechanically attached anchor sheet. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier:
TOPCOAT FireOut"' Fire Barrier Coating, VersaShield' Fire -Resistant Slip Sheet or
(optional)
VersaShield® Solo' Fire -Resistant Slip Sheet installed per manufacturer's installation
instructions.
Anchor sheet:
GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet, Ruberoid® 20 Smooth or
GAFGLAS® Stratavent® Venting Nailable Base Sheet is secured as described below.
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #1:
diameter tin caps are spaced 8 in. o.c. in the min. 4 in. wide anchor sheet side laps and 8
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —45 psf. See General Limitation #7)
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #2:
diameter tin caps are spaced 6 in. o.c. in the min 4 in. wide anchor sheet side laps and 6
in. o.c. in the Feld of the sheet in two staggered rows.
(Maximum Design Pressure. —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec'
Option #3:
AccuTrac® Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 16
in. o.c. in the min. 4 in. wide anchor sheet side laps and 16 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure. —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec"' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec'
Option #4:
AccuTrac® Flat Plates or Drill-Tec"' 3 in. Ribbed Galvalume Plate (Flat) are spaced 12
in. o.c. in the min 4 in. wide anchor sheet side lap's and 12 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure. —60 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec'
Option #5:
AccuTrac® Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 8 in.
o.c. in the'min. 4 in. wide anchor sheet side laps and 8 in. o.c. in the field of the sheet in
three staggered rows.
(Maximum Design Pressure. —82.5 psf. See General Limitation #7)
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 15 of 27
One or more layers of any of the following insulations.
Insulation Layer Insulation Fasteners Fastener Density/ft,
(Table 3)
EnergyGuard'" Polyiso Insulation, EnergyGuard'" Tapered Polyiso Insulation, EnergyGuard" Ultra Polyiso
Insulation, EnergyGuard' RH Polyiso Insulation, EnergyGuard' RH Tapered Polyiso Insulation
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered in a full mopping of approved hot asphalt within the EVT range and at a
rate of 2040 lbs./100 ft. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: GAFGLAS® Stratavent® Perforated Venting Base Sheet is laid dry over the insulation.
Ply Sheet: When optional cap sheet is present:
Two or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6 adhered
in a full mopping of hot asphalt applied at 2040 lbs./sq. installed per manufacturer's
installation instructions.
When optional cap sheet is not present:
Three or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6
adhered in a full mopping of hot asphalt applied at 20401bs./sq. installed per
manufacturer's installation instructions.
Cap Sheet (Optional):
GAFGLAS® Mineral Surfaced Cap Sheet, Tri-Ply® BUR Granule Cap Sheet or
GAFGLAS® EnergyCap' Mineral Surfaced Cap Sheet adhered in a full mopping of hot
asphalt applied at 20 — 401bs./sq. installed per manufacturer's installation instructions.
Surfacing:
Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1.
Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2.
Topcoat" Membrane or Topcoat® Surface Seal SB applied at I to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
3.
Aluminum Fiber Roof Coating.
Maximum Design
Pressure:
See fastening options above.
NOA No.: 18-0919.07
MuAMI•D,00e COUNTY Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 16 of 27
Membrane Type:
BUR
Deck Type II:
Wood, Insulated
Deck Description:
19/32" thick or greater or greater plywood or wood plank secured 6 in. o.c. at panel end
and intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type A(5):
All insulation layers are adhered, to a mechanically attached anchor sheet. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier:
FireOut' Fire Barrier Coating, VersaShield® Fire -Resistant Slip Sheet or VersaShield®
(optional)
Solo' Fire -Resistant Slip Sheet.
Anchor sheet:
GAFGLAS® #75 Base Sheet or Tri-Ply® #75 Base Sheet is secured as described below
with Dade County Approved min. 12 ga. galvanized ring shank nails and 32 ga., 1-5/8 in.
diameter tin tabs.
Fastening:
Nails and tabs are spaced 8 in. o.c. in the 4 in. wide side lap and 8 in. o.c. in two
staggered rows in the field of the sheet.
One or more layers of any
of the following insulations.
Base Insulation Layer
Insulation Fasteners Fastener
(Table 3) Density/ft'
EnergyGuard" Polyiso Insulation, EnergyGuard' Tapered Polyiso Insulation, EnergyGuard' RH Polyiso
Insulation, EnergyGuard' RH Tapered Polyiso Insulation
Minimum 1" thick N/A N/A
Top Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ftz
Structodek® High Density Fiberboard Roof Insulation, Securock® Gypsum -Fiber Roof Board
Minimum''/:" thick N/A N/A
Note: All insulation shall be adhered in a full mopping of approved hot asphalt within the EVT range and at a
rate of 2040 lbs.1100 fe. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Ply: Two or more plies of GAFGLASO FlexPly'" 6 adhered with hot asphalt applied at 20-25
lbs./sq.
Cap Ply: GAFGLAS® Mineral Surfaced Cap Sheet adhered with hot asphalt applied at 20-25
lbs./sq.
Surfacing: Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at I to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
Maximum Design
Pressure: —52.5 psf. (See General Limitation #7)
MAMMADE COUNTY
Km 0
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 17 of 27
Membrane Type: BUR
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater thick or greater plywood or wood plank secured 6 in. o.c. at panel end
and intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type C: All layers of insulation are mechanically attached to roof deck. Membrane is
subsequently fully adhered to insulation.
All General and System Limitations shall apply.
Fire Barrier: FireOut' Fire Barrier Coating, VersaShield' Fire -Resistant Slip Sheet or VersaShield'
(optional) Solo' Fire -Resistant Slip Sheet.
One or more layers of any of the following insulations.
Base Insulation Layer (Optional) Insulation Fasteners Fastener
(Table 3) Density/ft'
EnergyGuard' Polyiso Insulation, EnergyGuardd" RA Polyiso Insulation, EnergyGuard' RN Polyiso Insulation
Minimum 1" thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. GAF requires either a ply of GAFGLAS' Stratavent' Perforated Venting Base Sheet
laid dry or a layer of EnergyGuard' Perlite Roof Insulation or wood fiber overlay board on all
polyisocyanurate applications.
Top Insulation Layer
Insulation Fasteners Fastener
(Table 3) Density/ft2
SECUROCK' Gypsum -Fiber Roof Board
Minimum '/" thick
2,8 1:1.78 ft'
Base Ply:
Two or more plies of GAFGLAS® FlexP1ym 6 adhered with hot asphalt applied at 20-25
lbs./sq. installed per manufacturer's installation instructions.
Cap Ply:
GAFGLAS'Mineral Surfaced Cap Sheet, Tri-Ply' BUR Granule Cap Sheet or
GAFGLAS' EnergyCap' Mineral Surfaced Cap Sheet adhered with hot asphalt applied
at 20-25 lbs./sq. installed per manufacturer's installation instructions
Surfacing:
Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 3001bs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat' Membrane or Topcoat' Surface Seal SB applied at I to 1.5 gal./sq.
OR
Topcoat' ME Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat' Membrane applied at 0.5 to 0.75 gal./sq.
3. Fiber Aluminum Roof Coating.
Maximum Design
Pressure: —60 psE (See General Limitation #7)
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 18 of 27
Membrane Type: BUR
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank secured 6 in. o.c. at panel end and intermediate
supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type D: All insulation is loose laid with preliminary attachment to roof deck. Anchor sheet is
subsequently mechanically fastened through insulation to the roof deck.
All General and System Limitations shall apply.
One or more layers of any of the following insulations
Insulation Layer
Insulation Fasteners Fastener
(Table 3) Density/ft'
EnergyGuard' Polyiso Insulation, EnergyGuard'" Ultra Polyiso Insulation, EnergyGuard'" RA Polyiso
Insulation
Minimum 1.3" thick
N/A N/A
Structodek® High Density Fiber Board
Minimum 1" thick
N/A N/A
Note: Insulation shall
have preliminary attachment, prior to the installation of the base sheet, at a minimum
application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and
four fasteners for any
insulation board having no dimension greater than 8 ft. All layers of insulation, optional
thermal barrier (when present) and base sheet shall be simultaneously fastened. See base sheet below for
fasteners and density.
Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Fire Barrier:
FireOut' Fire Barrier Coating, VersaShield® Fire Resistant Roof Deck Protection,
(optional)
VersaShield® Solo"' Fire -Resistant Slip Sheet, DensDeck® Roof Board, Securock' Glass -
Mat Roof Board or Securock' Gypsum Fiber Roof Board.
Base Sheet:
Install one ply of GAFGLAS® #75 Base Sheet, Tri-Ply #75 Base Sheet, GAFGLAS® #80
Ultima'" Base Sheet, GAFGLAS® Stratavent® Nailable Venting Base Sheet or Ruberoid®
20 Smooth applied over the loose laid insulation with 2" side laps mechanically fastened as
described below;
Fastening
Drill-Tec"' 412 Fastener or Drill-Tec'" #14 Fastener and Drill-Tec"' 3" Steel Plate, Drill -
Option #1:
Tec 3 in. Ribbed Galvalume Plate (Flat), Drill-Tec"" AccuTrac® Flat Plate or Drill-Tec"'
AccuTrac® Recessed Plate is installed through the base sheet and insulation in 3 rows 12"
o.c. One row is in the 2" side lap. The other rows are equally spaced approximately 12"
o.c. in the field of the sheet.
(Maximum Design Pressure —45 psf. See General Limitation #9)
Fastening
Drill-Tec' #12 Fastener or Drill-Tec'" #14 Fastener and Drill-Tec"" 3" Steel Plate, Drill -
Option #2:
Tec 3 in. Ribbed Galvalume Plate (Flat), Drill-Tec"" AccuTrac® Flat Plate or Drill-Tec"
AccuTrac® Recessed Plate is installed through the base sheet and insulation in 4 rows 8"
o.c. One row is in the 2" side lap. The other 3 rows are equally spaced approximately 9"
o.c. in the field of the sheet.
(Maximum Design Pressure —75 psf. See General Limitation #9)
Fastening
GAFGLAS® #80 Ultimam Base Sheet, Ruberoid® 20 Smooth, Ruberoid® Mop Smooth
Option #3:
attached to deck with approved annular ring shank nails with a minimum embedment of 1"
into the wood substrate and inverted 3" steel plate at a fastener spacing of 9" o.c. at the 4"
lap and in two rows staggered with a fastener spacing of 9" o.c. in the center of the
membrane. Not for use with DensDeck or Securock Fire Barrier
(Maximum Design Pressure —60 psf. See General Limitation #7)
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/19
Page 19 of 27
Fastening (Continued) Drill-Tec' #12 Fastener or Drill -Tee #14 Fastener and Drill-Tec'° 3" Steel Plate, Drill -
Option #4:
Tee 3 in. Ribbed Galvalume Plate (Flat), Drill-Tec' AccuTrac® Flat Plate or Drill-Tec''
AccuTrac® Recessed Plate in 4 rows 12" o.c. One row is in the 2" side lap. The other rows
are equally spaced approximately 9" o.c. in the field of the sheet.
(Maximum Design Pressure —60 psf. See General Limitation 99)
Ply Sheet:
One or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® F1exPly' 6 or
GAFGLAS® #80 Ultima Base Sheet adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq. installed per manufacturer's installation
instructions.
Cap Sheet:
(Optional) One ply of GAFGLAS® Mineral Surfaced Cap Sheet, Tri-Ply BUR Granule
Cap Sheet or GAFGLAS® EnergyCap' Mineral Surfaced Cap Sheet adhered in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20401bs./sq.
installed per manufacturer's installation instructions.
Surfacing:
Optional on granular surfaced membranes; required for smooth membranes. Chosen
components must be applied according to manufacturer's application instructions.
All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
3. Fiber Aluminum Roof Coating.
Maximum Design
Pressure:
See Fastening Options
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 20 of 27
n r :
`per on=msu a e
Deck Description: 19/32" or greater plywood or wood plank decks secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type E(1): Anchor sheet mechanically attached to roof deck.
All General and System Limitations shall apply.
Fire Barrier: Topcoat® FireOut' Fire Barrier Coating, VersaShield® Fire Resistant Roof Deck
(optional) Protection, VersaShield® Solo'"' Fire -Resistant Slip Sheet installed per manufacturer's
installation instructions.
Base sheet: GAFGLAS® #80 Ultima`" Base Sheet, Stratavent® Nailable Venting Base Sheet, Ruberoid®
20 Smooth, Ruberoid® SBS Heat -Weld" Smooth or Ruberoid® SBS Heat -Weld' 25 base
sheet mechanically fastened to deck as described below;
ffiastening ase e n of
ptio nc he ttache dec w� ppreve n rin h '
Fastening
Option #2:
Surfacing:
Maximum Design
Pressure:
Design Pressure —52.5 psf. See General Limitation #7)
GAFGLAS® #80 Ultimate' Base Sheet, Ruberoid® 20 Smooth or Ruberoid® Mop Smooth
attached to deck with approved 1 %d' annular ring shank nails and inverted 3" steel plate at a
fastener spacing of 9" o.c. at the 4" lap and in two rows staggered with a fastener spacing of
9" o.c, in the center of the membrane.
(Maximum Design Pressure —60 psf. See General Limitation #7)
Optional on granular surfaced membranes; required for smooth membranes. Chosen
components must be applied according to manufacturer's application instructions.
All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat' Membrane applied at 0.5 to 0.75 gal./sq.
3. Fiber Aluminum Roof Coating.
See Fastening Options
NOA No.: 18-09 9.0V
Mwni•onoecournr x i Kation Date: 1 4/2 1
... � � A 1 tL(IS/
ag o
Membrane Type: BUR
Deck Type 1:
Wood, Non -insulated
Deck Description:
19/32" or greater plywood or wood plank decks secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type E(2):
Anchor sheet mechanically attached to roof deck.
All General and System Limitations shall apply.
Fire Barrier:
Topcoat® FireOut'' Fire Barrier Coating, VersaShield®Fire Resistant Roof Deck
(optional)
Protection, VersaShield® Solo' Fire -Resistant Slip Sheet installed per manufacturer's
installation instructions.
Anchor sheet:
GAFGLAS® #80 Ultima Base Sheet mechanically attached with Miami -Dade County
Approved min. 1'/4 long, 12 ga., annular ring shank nails and 1-5/8" diameter tin caps
spaced 7" o.c. in the min 4" wide side laps and in 3 staggered rows in the field of the sheet.
Ply Sheet:
Two or more plies of GAFGLAS® Ply 4, Tri-Plyl Ply 4, GAFGLAS® FlexPly" 6 adhered to
the base sheet in full mopping of approved asphalt applied within the EVT range and at a
rate of 2040 lbs./sq. installed per manufacturer's installation instructions.
Cap Sheet:
One ply of GAFGLASO Mineral Surfaced Cap Sheet, Tri-Ply® BUR Granule Cap Sheet or
GAFGLASO EnergyCapTM Mineral Surfaced Cap Sheet adhered in a full mopping of
approved asphalt applied within the EVT range and at a rate of 2040 lbs./sq. installed per
manufacturer's installation instructions.
Surfacing:
Optional on granular surfaced membranes; required for smooth membranes. Chosen
components must be applied according to manufacturer's application instructions.
All coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
Maximum Design
Pressure: -82.5 psf. (See General Limitation #7)
MIAMI•DADE COUNTY
.... I
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 22 of 27
Membrane Type:
BUR
Deck Type 1I:
Wood, Non Insulated
Deck Description:
Min. 15/32" thick or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type E(3):
Anchor sheet mechanically attached to roof deck.
All General and System Limitations shall apply.
Fire Barrier:
TOPCOAT FireOut' Fire Barrier Coating, VersaShield® Fire -Resistant Slip Sheet or
(optional)
VersaShield® Solo'I Fire -Resistant Slip Sheet installed per manufacturer's installation
instructions.
Anchor sheet:
GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet, Ruberoid® 20 Smooth or
GAFGLAS® Stratavent® Venting Nailable Base Sheet is secured as described below.
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #1:
diameter tin caps are spaced 8 in. o.c. in the min. 4 in. wide anchor sheet side laps and 8
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —45 psf. See General Limitation 97)
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in.
Option #2:
diameter tin caps are spaced 6 in. o.c. in the min 4 in. wide anchor sheet side laps and 6
in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill -Tee' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill -Tee'
Option #3:
AceuTrac® Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 16
in. o.c. in the min. 4 in. wide anchor sheet side laps and 16 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec7 914 Fasteners and Drill-Tec'°' 3 in. Standard Steel Plates, Drill -Tee
Option #4:
AccuTrac® Flat Plates or Drill -Tee 3 in. Ribbed Galvalume Plate (Flat) are spaced 12
in. o.c. in the min 4 in. wide anchor sheet side laps and 12 in. o.c. in the field of the sheet
in two staggered rows.
(Maximum Design Pressure: —60 psf. See General Limitation #7)
Fastening
Drill-Tec' #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec'
Option #5:
AccuTrac® Flat Plates or Drill-Tec'" 3 in. Ribbed Galvalume Plate (Flat) are spaced 8 in.
o.c. in the min. 4 in. wide anchor sheet side laps and 8 in, o.c. in the field of the sheet in
three staggered rows.
(Maximum Design Pressure: —97.5 psf. See General Limitation #7)
Ply Sheet:
When optional cap sheet is present:
Two or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6 adhered
in a full mopping of hot asphalt applied at 2040 lbs./sq. installed per manufacturer's
installation instructions.
When optional cap sheet is not present:
Three or more plies of GAFGLAS® Ply 4, Tri-Ply® Ply 4, GAFGLAS® Flex Ply 6
adhered in a full mopping of hot asphalt applied at 2040 lbs./sq. installed per
manufacturer's installation instructions.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 23 of 27
Cap Sheet: (Optional) GAFGLAS® Mineral Surfaced Cap Sheet, Tri-Ply® BUR Granule Cap Sheet
or GAFGLAS EnergyCap' Mineral Surfaced Cap Sheet adhered in a full mopping of hot
asphalt applied at 20 — 40 lbs./sq. installed per manufacturer's installation instructions.
Surfacing: Optional on granular surfaced membranes; required for smooth membranes.
Chosen components must be applied according to manufacturer's application
instructions. All coatings must be listed within a current NOA.
1. Gravel or slag applied at 4001bs./sq. and 300 lbs./sq. respectively in a flood coat of
approved asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at 1 to 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by
Topcoat® Membrane applied at 0.5 to 0.75 gal./sq.
3. Fiber Aluminum Roof Coating.
Maximum Design
Pressure: See Fastening Above.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 24 of 27
Membrane Type: BUR
Deck Type II: Wood, Non Insulated
Deck Description: Min. 15/32" thick or greater plywood or wood plank secured 6 in. o.c. at panel end and
intermediate supports with 8d ring shank nails to supports spaced 24 in. o.c. at max.
System Type E(4):
Anchor sheet mechanically attached to roof deck -
All General and System Limitations shall apply.
Fire Barrier:
TOPCOAT FireOuf" Fire Barrier Coating, VersaShield® Fire -Resistant Slip Sheet
(optional)
VersaShield® Solo' Fire -Resistant Slip Sheet, installed per manufacturer's installation
instructions.
Anchor sheet:
GAFGLAS® #75 Base Sheet, Tri-Ply® #75 Base Sheet, Ruberoid® 20 Smooth or GAFGLAS®
Stratavent® Venting Nailable Base Sheet is secured as described below.
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in. diameter
Option #1:
tin caps are spaced 8 in. o.c. in the min. 4 in. wide anchor sheet side laps and 8 in. o.c, in the
field of the sheet in two staggered rows.
(Maximum Design Pressure. —45 psf. See General Limitation #7)
Fastening
Miami -Dade County Approved min. 12 ga. annular ring shank nails and min. 1-5/8 in. diameter
Option #2:
tin caps are spaced 6 in. o.c. in the min 4 in. wide anchor sheet side laps and 6 in. o.c. in the
field of the sheet in two staggered rows.
(Maximum Design Pressure: —52.5 psf. See General Limitation #7)
Fastening
Drill-Tec'" #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec' AccuTrac'
Option #3:
Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 16 in. o.c. in the min. 4
in. wide anchor sheet side laps and 16 in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure. —52.5 psf. See General Limitation #7)
Fastening
Drill -Tee #14 Fasteners and Drill-Tec' 3 in. Standard Steel Plates, Drill-Tec' AccuTrace
Option #4:
Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 12 in. o.c. in the min 4
in. wide anchor sheet side laps and 12 in. o.c. in the field of the sheet in two staggered rows.
(Maximum Design Pressure: —60 psf. See General Limitation 97)
Fastening
Drill-Tec' #14 Fasteners and Drill -Tee' 3 in. Standard Steel Plates, Drill-Tec' AccuTrac®
Option #5:
Flat Plates or Drill-Tec' 3 in. Ribbed Galvalume Plate (Flat) are spaced 8 in. o.c. in the min. 4
in. wide anchor sheet side laps and 8 in. o.c. in the field of the sheet in three staggered rows.
(Maximum Design Pressure: —97.5 psf. See General Limitation #7)
Base Sheet:
Ruberoid® 20 Smooth adhered in a full mopping of hot asphalt applied at 20-40 lbs./sq.
installed per manufacturer's installation instructions.
Cap Sheet:
GAFGLAS® Mineral Surfaced Cap Sheet, Tri-Ply® BUR Granule Cap Sheet or GAFGLAS
EnergyCap' Mineral Surfaced Cap Sheet adhered in a full mopping of hot asphalt applied at 20
— 40 lbs./sq. installed per manufacturer's installation instructions.
NOA No.: 18-0919.07
VN
M"PDAD: COUNTY Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 25 of 27
Surfacing: Optional on granular surfaced membranes; required for smooth membranes. Chosen
components must be applied according to manufacturer's application instructions. All
coatings must be listed within a current NOA.
1. Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq. respectively in a flood coat of approved
asphalt at 60 lbs./sq.
2. Topcoat® Membrane or Topcoat® Surface Seal SB applied at Ito 1.5 gal./sq.
OR
Topcoat® MB Plus applied at 0.5 to 0.75 gal./sq.(to be used as a primer) followed by Topcoat®
Membrane applied at 0.5 to 0.75 gal./sq.
3. Aluminum Fiber Roof Coating.
Maximum Design
Pressure: See Fastening Above.
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 26 of 27
WOOD DECK SYSTEM LIMITATIONS:
1 A slip sheet is required with GAFGLAS® Ply 4 and GAFGLAS® Flex Ply' 6 when used as a mechanically fastened
base or anchor sheet. 1
2. Minimum %<" DensDecle" Roof Board or %:" Type X gypsum board is acceptable to be installed directly over the
wood deck.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 2040 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each sidelap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be
limited to a maximum design pressure of 45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 2751bf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the
fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida Registered Professional Engineer, Registered Architect, or Registered
Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value
taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application
Standard RAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application
Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer,
Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within
this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS I I 1 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and comers). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and comers). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF TMS ACCEPTANCE
NOA No.: 18-0919.07
Expiration Date: 11/04/23
Approval Date: 11/08/18
Page 27 of 27