HomeMy WebLinkAboutREVISIONS - BUILDING PERMITOFFICE USE ONLY:
DATE FE=: 7112119
REVISION FEE:
FERMIT #
RECEIPT #
PLANNING & DEVELOPMENT SERVICES
BUILDING& CODE REGULATIONDLVISION RECEIVED
2300 VIRGINIA AVENUE
FORT PIERCE, FL 34982.5652 JU L 12 2019
(772) 46M1553
APPLICATION FOR BUILDING PERMIT REVISIONE
ST. Lucie County, Permitting
PROJECT INFORMATION
LOCATION/SITSCANNEDE BY
ADDRESS: Sftucie C®unh,
497 Sandia Avenue, Port St Lucie, FL 34983
DETAILED DESCRIPTION OF PROJECT
REVISIONS:
adding self adhered roof system 1,onludrSS r
CONTRACTOR INFORMATION:
STATE of FL REGJCERT. #: CCC1327420
BUSINESS NAME: Ameri-Con Enterprises, Inc.
ST. LUCIE CO CERT. #:
QUALIFIERS NAME: David Kielb
ADDRESS: 1466 SW San Sebastian Avenue
CITY: Port SL Lucie STATE: FIL ZIP: 34953
PHONE (DAYTIME): 954-444-7717 FAX: --_ -
OWNER/BUILDER INFORMATION:
NAME: Jodie Sweeney
ADDRESS:497 Sandia Avenue
CITY: Port St Lucie . STATE: FL ZIP: 34983
PHONE (DAYTIME: 954444-7717 FAX:
ARCHITECTIENGINEER INFORMATION:
NAME:
S '
MIMI®- . � ADE MIAW-DADECOUNTY
� PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 209
BOARD AND CODE ADMINISTRATION DMSION Miami, Florida 33175-2474
• •- RECEIVED 6)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) .msamldade ovleeonom
]'olyglassUSA Inc. JUL 12 2�19
1111 W. Newport Center Drive
Deerfield Beach, FL 33442 �T• Lucie County, permitting
I
SCOPE:
This NOA is-bbing issued under the applicable rules and'regulations governing the use of construction materials. The
documentation submitted has been reviewed and. accepted by Miami -Dade County RER -' Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) andlofthe AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will. incur the expense of such testing and the AHJ may immediately revoke, modify, or -
suspend the use of such product or material•with in their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami Dade County Product Control Section that this product or material fails to meet.the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Polystick Underlayments
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change'
in the applicable building code negktively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any, other purposes shall automatically terminate this NOA. Failure to comply with -any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number;preceded by the words Miami -Dade -County, Florida, and followed
by the expiration date maybe displayed •in,advertising literature. If any portion ofthe NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user,by the manufacturer or its distributors and
shall be available for inspection at the job site, at the request of. the Building Official.
This NOA renews and revises NOA No.15-0410.04 and consists of pages 1 thro
COPY
The submitted documentation was reviewed by Freddy Semino.,
REVIEWED F
ODE COMPLIANCE NOANo.: 17-0614.22
MIAMI•nADE COU Expiration Date: 09/13/21
T. L.UCIE COU14TY Approval Date: 07/06/17
BOCC Page I of 8
ROOFING COMPONENT APPROVAL
Category
Roofing
Sub -Category:
Underlayment
Material:
SBS , APP.S@tf Adhering Modified Bitumen
PRODUCTS DESCRIPTION:
' '
Test Product
Product
Dimensions
Specification Description
Polystick IR-Xe
65' x 3'3 ;/a"
ASTM D 1970 A fine granular/sand top surface self -adhering, APP
Manufacturing
Or 65' x 3'
polymer modified, fiberglass reinforced, bituminous.
Location #1 & #2
60 mils thick,.,
sheet material for use as an underlayment in sloped roof
assemblies. Designed as an ice & rain shield.
Polystick.Dual Pro
61' x 3'3 3/s"
TAS 103 and A rubberized asphalt self -,adhering, glass-fiber/polyester
Manufacturing
60 mils thick '•"
ASTM D 1970 ' reinforced waterproofing membrane. Designed as a
Location #2
metal roofing and roof file »nderlayment,
Polystick Tile Pro
61'.rt 3?3-Ns"
TAS-103 and A rubberized asphalt self-adhering;•glass-fiber/polyester
Manufacturing
60-mils thick "
.. ASTM D 1970 reinforced waterproofing' membrane. Designed as a metal
Location 42
roofing and roof tile underlayment.
Polystick TU Max
65'8" x 3'3-3/8"
TAS 103 and A rubberized asphalt self -adhering, polyester reinforced
Manufacturing
60 mils thick
ASTM D 1970 waterproofing membrane; Designed as a a roof tile.... ,
Location #1 & #2
underlayment.
Polystick TU P
32'10" x TINs"
TAS 103 and A rubberized asphaltwaterproofing membrane, glass=
Manufacturing
130 mils thick
ASTM D 1970 fiber/polyester reinforced, with a granular surface
Location #2 "
designed f6r use as a tile roof underlayment.
Polystick TU Plus
65' x 33 Ns"
TAS 103 and A rubberized asphalt self -adhering, glass-fiber/polyester,
(Surface Printing)
.80 mils thick
ASTM D 1970 . reinforced waterproofing membrane. Designed as a metal
Manufacturing
roofing and roof file underlayment.
Location #1 & #2
Polystick MTS
65'8" x TINs" ..
TAS 103 A homogeneous, rubberized asphalt waterproofing
Manufacturing
60' mils thick .
membrane, glass fiber reinforced with polyolefinic film
Location #2
on the upper surface for use as an underlayment for metal
roofing, roof tile, slate tiles and shingle underlayment.
Polystick MTS Plus
65'8" x 313 3/s'•
TAS 103 A•homogeneous, rdbberized asphalt waterproofing "
Manufacturing
60 mils thick
membrane,:glass fiber 'reinforced with polyolefinic film
Location #2
on the upper surface for use as. an underlayment for metal
roofing, roof tile, slate tiles and shingle underlayment.
Elastoflez S6 G
32'10" x 33 '/s"
'TAS 103 and Polyester reinforced, SBS modified bitumen membrane
Manufacturing
ASTM D 6164 . with a sanded back face' and a granule top surface. For
Location #2` '. ' .
use in roof tile underlayment systems.
"'•NOA No.: 17-0614.22
MIAMI•DADE COUNTY Expiration Date: 09/13/21
,...�
Approval Date: 07/06/17
Page 2 of 8
AIANUFACTURING PLANTS:
1. Hazelton, PA
2. Winter Haven, FL
Test Agency
TrinitYI•ERD - ..
PRI Asphalt Technologies
Momentum Technologies, Inc.
LABELING:
EVIDENCE SUBMITTED • • `
Test Identifier
Test Name/Reporf
Date
P10870.09:08-R1'
TA3.103
12/04/08
P10870.04.09
TAS 103/ASTM D4798 & G155
04/13/09
P33360.06.10
ASTM D1970 . ,
07101/10
P333.70.03.11
TAS 103
03/02/11
P33370.04.11
ASTM D 1623
04/26/11
P36900.09.11
TAS'103/ASTM D4798 & G155
1.
09/01/11
P37300.10.11
TAS 110/ASTM D4798 & D1970
10/19/11
P40390.08.12-2
ASTM D 1623
08/07/12
P37590.07.13-1
ASTM D6164
07/02/13
P45270.05.14
TAS 103, TAS 110 & ASTM D1623
'05112/14
P46520.10.14•
ASTMD1623
10/03/14
P44360.10.14
TAS,103 &TAS 110
10/07/14
P43290.10.14
ASTM D 1070 & TAS 110
10/17/14
PlYG-'SC10130.06.16-3
TAS 103 & TAS 110
06/21/16
PLYG-10130.06.16-1
ASTM D1970 & TAS 110
06/27/16
•PUSA-035-02-01
TAS 103
09/29/06
PUSA-055-02-02
TAS 103
12/10/07
PUSA-089-02-01
TAS 103/ASTM D4798 & G155
07/06/09
TX20H7A
RX14E8A
DX23D8B
DX23D8A
TAS 103/ASTM D4798 & G155
04/01/09
TAS 103/ASTM D4798 & G155
11/09/09
TAS 103/ASTM.D4798-& G155
02/18/10
TAS 103/ASTM D4798 & G155 .
02118/10•
1. All membranes,or packaging shall. bear the imprint or identifiable marking of the manufacturer's name or logo, city
and state of manufacturing facility and the following statement: "Miami -Dade County Product Control Approved"
or the Miami -Dade County Product Control Seal as shown below...'. .
MIAMFDADECOUNTY
1 1
BUII.DING PERMIT REQUIREMENTs:
Applicationfor building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly evaluate the
installation of this materials.
NOA•No.: 174614.22
MIAMI•DAD, COUNTY Expiration Date: 09/13/21
! Approval Date: 07/06/17
Page 3 of 8
INSTALLATION PROCEDURES:
Deck Type 1:
Wood, non -insulated
Deck Description:
Min. 19/32" plywood or wood plank
System Type E(1):
Anchor sheet mechanically fastened to deck,.membrane adhered
Anchor/Base Sheet:
Ong or more plies. of ASTM D 226 Type II pr. ASTM D 2626. „ • ,
Fastening: •
Per FBC 1518.2 & 1518A Nails and tin caps .12";grid, 6" o.c. at a minimum 4"' head lap., (for
base sheet -only) . ,
Membrane:
Polystick 1R-Xe, Polystick Dual P&,'Polystick THe Pro, Polystick TU Max, Polystick
TU P; Polystick TU Plus, Polystick MT•S or Polystick MTS Plus, self -adhered.
Surfacing:
See General Limitations.Below.
Deck Type 1:
Wood, nog -insulated
Dcck Description:
Min. 19/32" plywood or wood plank .
System Type E(2):
Anchor sheet mechanically fastened to.deck,: membrane adhered
Anchor/Base Sheet:
One of more plies of ASTM D 226 Type D' or ASTM D 2626.
Fastening:
Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6": o.c. at a minimum 4" head lap. (for
base sheet only
Membrane:
Elastoflea S6 G, hot asphalt applied
Surfacing:
See General Limitations Below.
Deck Type 1: Wood, non -insulated.
Deck Description: Mini; 19/32"plywoodor.woodplank
System Type E(3): -Base sheet mechanically fastened to deck, subsequent cap membrane self- adhered.
Anchor%Base Sheet: One'or'moie plies of ASTM D 226 Type II or ASTM D 2626:
Fastening: Per FBC 1518.2 & 1518.4 Nails and tin caps 12" grid, 6" o.c. at a minimum 4"head lap. (for
base sheet only) . •` "S • ` ••
Ply Sheet: Polystick MTS, Pius, self -adhered with minimum 37-horizontal,laps and•minimum:6"
vertical laps,
Membrane: Polystick TU Plus, self-adhered'1 "
Surfacing: See General Limitation's Below.
NOA No.: 17-6614.22
MIAMMADECOMM
Expiration Date: 09/13/21
Approval Date: 07/U6%17
Page 4 of 8
INSTALLATION REQurREMENTs:
1. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose deck panels, and
sweep the deck thoroughly to remove any dust and debris prior to application:
2. Place the underlayment over metal drip edge in accordance with RAS 111.
3. Place the fast course of membrane parallel to the eave, rolling the membrane to obtain maximum contact.
Remove the release film as the membrane is'applied. All side laps shall be a minimum of 3" and end laps shall
be a minimum of 6". Roll the membrane into place after removing the release strip. Vertical strapping of the
roof with Polystick is•acceptable.' •Membrane'shall be back nailed in accordance with applicable building code.
4. When applying the membrane in the valley, start at the low point and workto the high point, rolling the
membrane from the center outward in both directions. '
5. For ridgeapplications, center the membrane and roll from the center outward in both directions.
6. Roll or:broom the entire membrane surface so as to have full contact with the "surface, giving special attention
to lap areas.
. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance:
8. All protrusions or drains shall be initially taped with a 6" piece of underlayment. The flashing tape shall be
pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be
applied over the underlayment. .
GENERAL LIMITATIONS'
1. Fire classification is not part of this acceptance.
2. Polystick Dual Pro,-Polystick Tile Pro, PolystickTU, Plus, Polystick MTS and Polystick MTS Plus maybe
used in asphaltic shingles, wood shakes and shingles, non-structural metal roofing, roof tile systems and quarry
slate roof assemblies. ; .
Polystick TU P may be used in all the previous assemblies listed except metal roofing.
Polystick IR-Xe may be used in all the previous assemblies listed except metal roofing and roof tile systems.
Polystick TU Max may be used in non-structural metal roofing and roof tile systems.
Elastoflex 86 G may be used in roof tile systems only.
3. Deck requirements shall be in compliance with applicable building code.
4. Polystick IR-Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU
Plus, Polystick MTS and Polystick NITS Plus shall be applied to a smooth, clean and dry surface. The deck
shall be free of irregularities.
5. Polystick IR Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU
Plus, Polystick MTS and Polystick MTS Plus shall not be adhered directly over a pre-existing roof membrane
as a recover system.
6. Polystick IIt Xe, Polystick Dual Pro, Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU
Plus, Polystick MTS and Polystick MTS Plus shall not be left exposed as a temporary roof for longer than the
amount of days listed in the table below after application. Polyglass reserves the right to revise or alter product
exposure times; not to exceed the preceeding maximum time limitations.
Exposure Limitations (Days)
MTS
Ht-Xe
Elastoflex
S6 G
TU
Plus
TU P
Tile Pro
Dual Pro
TU Max
MTS Plus
Winter Haven FL
180
1 90
180
180
180
180
180
1 180
1 180
Hazelton PA
N/A
1 90
N/A
180
NIA
N/A
N/A 1
180
1 N/A
,7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
ntwrtuuane courrry NOA No.: 17-0614.22
.. • � Expiration Date: 09/13/21
Approval Date: 07/06/17
Page 5 of 8
8.
2
Rule 61G20-3 of the Florida Administrative Code.
In roof tile application, data for the attachment resistance of roof tiles shall'be as set forth in the roof tile
manufacturer's Notice of Acceptance. . . • 1. „ v ,.
Polystick Tile Pro, Polystick TU.. Max,.Polystick TU Plus or Elastoflex 86 G may be used in -both adhesive
set and mechanically fastened roof tile applications.. .
Polystick Dual Pro is limited to mechanically,.fastened roof file applications, ,
Polystick MTS and Polystick MTS Plus are limited to mechanically fastened with the limitations outlined in
Section 9.
Polystick TU P maybe used in mechanically fastened roof tile applications with the exception.of mortar set tile
applications.
When loading roof tiles on roof tile underlayment for (direct -to -deck) tile assemblies; the maximum roof slope
shall be as follows: (See •Table Below)
Tile :.
Polystick
: Elastoflex
Polystick TU Plus,
Polystick
Polystick':
:; ,• -System (E3)
Profile
MTS
S6 G
TU P, Tile Pro,
TU Max
MTS Plus
MTS Plu's with
Dual Pro..,..
TU Plus
Flat Tile
Prohibited
4:12
6:12
6:12
5H2
6:12
without battens
Profiled
Prohibited
4:12
6:12
6:1-2
4:12:
-6:12
Tile
without battens
The above slope limitations can be exceeded only by using battens in accordance with the Approved Tile System.
Notice of Acceptance and applicable Florida Building Code requirements. When battens are required they shall
be utilized during loading and installation of tiles.
10. Care should be taken during the loading procedure td'keep foot•traffic to a minimum and•to avoid dropping of
tile directly on. the underlayment: Refer to Polyglass'• Tile•loading detail below for loading procedure -two tiles
laid perpendicular to slope followed by a maximum four tile stack parallel to the slope; for a total •of 6 tiles = for
all underlayments except. Polystick MTS which shall .be•loaded.onto battens:
, •.f::
MIAMMADECODU
(6 Max. Per Stack)
NOA No.: 17-0614.22
Expiration Date: 09)13/21
Approval Date: 07/06 17
Page 6 of 8
11. , Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with
specific prepared roofing products. Polystick IR-ke, Polystick• Dual Pro, Polystick the Pro, Polystick TU
Max, Polystick TU P, Polystick TU Plus, Polystick MTS, Polystick MTS Plus or Elastoflex S6 G maybe
used with,any approved roof covering Notice of Acceptance listing PolystickIWXe, Polystick Dual Pro,
Polystick Tile Pro, Polystick TU Max, Polystick TU P, Polystick TU Plus, Polystick MTS; Polystick MTS
Plus or Elastoflex S6 G as a component part of an assembly in- the'Notice'of Acceptance.
If Polystick IR-Xe, Polystick Dual Pro,, Polystick Tile Pro, Polystick TU Max, P:olystick:TU P, Polystick
TU Plus, Polystick MTS, Polystick MTS Plus or Elastoflex S6 G are not listed, a request may be made to the
Authority Having Jurisdiction (AHJ) or the Miami -Dade County,Product Control Section for approval provided
that appropriate' documentation is provided to detail compatibility of the pt,oducfs,'wind uplift resistance, and fire
testing results.
POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICX MEMBRANES
PLEASE CHECK RTCH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC •APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS. '
1. Polyglass does accept the direct -application of Polystick underlayment membranes to wood decks. Installers are
cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is acceptable.
Please also refer to applicable Product Data Sheets of the corresponding products.
2. All rolls, with the exception of Polystick TU Plus should be back -nailed in selvage edge seam as per Polyglass
Back Nailing Guide. Nails shall be, 11 gauge ring shank type, applied with a minimum 1 %" metal disk as
required in Miami -Dade County or simplex type nail as otherwise allowable in other regions, at a minimum rate
of 12" o.c. Polystick TU Plus should be back nailed in designated area marked "nail area, area pars, clavar" on
the face of membrane, with the above stated nails and/or disks. The head lap membrane is to cover the area being
back -nailed. (Please refer to applicable local building codes prior to installation.)
3. All seal lap seams (selvage laps) must be rolled with a hand roller to ensure full contact.
All fabric over fabric; and granule over granule end laps, shall have a 6" wide, uniform layer of Polyglass
Polyplus 55 Premium Modified Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement,
XtraFlex 50 Premium Modified Wet/Dry Cement, Polyglass PG500 MB Flashing Cement, applied in between
the application of the lap. The use of mastic between the laps does not apply to Polystick MTS.
5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments. Refer to the Polyglass Tile
Loading Guidelines. See General Limitations #9 and #10.
6. Battens and/or Counter -battens, as required by the tile manufacturers NOA, must be used on all projects for
pitch/slopes of T712" or greater: It is suggested that on pitch/slopes in excess of 6 '/4"/12", precautions should be
taken, such as the use of battens to prevent tile sliding during the loading process.
7. Minimum cure time after membrane installation & before loading of roofing tiles is Forty -Eight (48) Hours.
S. Polystick membranes may not be used in any exposed application such as crickets, exposed valleys, or exposed
roof to wall details.
9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified
Flashing Cement, Polyglass Polyplus 50 Premium MB Flashing Cement, XtraFlex 50 Premium Modified'
Wet/Dry Cement, Polyglass PG500 MB Flashing Cement to the area in need of repair, followed by a patch of the
Polystick material of like kind should be set and hand rolled in place over the area needing such repair. Patching
membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so
that water will run parallel to or over the top of all laps of the patch.
NOA No.: 17-0614.22
MIAMMADECOUNTY Expiration Date: 09/13/21
,...,
Approval Date: 07/06/17
Page 7 of 8
10. All self -adhered membranes must be rolled to, ensure full contact with approved substrates. Polyglass requires a
minimum of 401bs for a weighted. roller for the rolling of the field membrane. Band rollers are acceptable for
rolling of pafches or small areas of the roof. Broomng inay.tie used where slope prohibits rolling.
11. All approved substrates,should be, dry, clean and properly prepared, before, any application of Polystick
.membranes commences. An approved substrate technical bulletin can.be finnished'upon request.,It.is.
recommended to refer to applicable building. codes prior to installation to verify acceptable substrates.
12. The Polyglass Miami -Dade Notice of Acceptance (NOA) dpproval'for'Polystickmembranes cairbe furnished
upon request 'by our Technicaf Services Department by calling-P(8011) 89440.
13. , Questions in regards to the application of Polyglass products should be directed to our Technical Services
Department at 1 (800) 894-4563.
14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by
the National Roofing Contractors Association (NRCA)..•
PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC•APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS.REQUHIEMENTS AND RECOMMENDATIONS.
END OF THIS ACCEPTANCE
z
•
MIAMMADE COUNTY
NOA No.: 17-06f4.22
Expiration Date: 09/13/21
Approval Date: 07/06/17
Page 8 of 8
POLYSTICK° IR=Xe
PRODUCT DESCRIPTION
Polystick IR-Xe, is a homogeneous rubberized asphalt waterproofing compound, fiberglass
reinforced, with an aggregate, surface for skid resistance for use in ice and watershield
applications. The rubberized asphalt seals around correcily installed nails on the weathering
surface. Split release backing film aids in easy positioning of sheets to maintain proper line.
Polystick IR-Xe underlayments are manufactured using patented ADESOo dual compound
Self -Adhesive technology, whereby a "hue" polymer modified asphalt compound
is applied on the top layer -and an aggressive self-adhesive compound is applied on
the bottom layer.
Polystick IR-Xe is packaged in a roll of approximately 2 squares weighing 70 Ibs
USES
• Specially designed for multiple steep slope applications
• Designed as effective reinforcement for perimeter and flashing details
• Added protection against areas prone to wind driven rain and Ice damming
FEATURES AND BENEFITS
• Proprietary asphalt compound and fiberglass mat for exceptional dimensional stability
• Surface engineered for superior slip resistance and long term performance
• Aggressive self adhesive compound for ease of application
TECHNICAL DESCRIPTION
TEST ••
PROPERTY
VALUE
ASTM D5147
Thickness, min, mm (mils)
21801
ASTM D5147
Maximum Load, Longitudinal and Transverse,
4.4 (25)
min, kN/m (Ibf/in.)
ASTM 1)5147
Elongation at break, min of modified
10
bitumen portion (%)
ASTM D5147
Tear Resistance, Longitudinal and Transverse,
89 (20)
min, N pbfl
ASTM E96
Mgisture Vapor Permeability, mm, perms
0.1
ASTM D1970
Adhesion to Plywood ®.40F, min, Ibf/ft width
2.0
ASTM D1970
Adhesion to Plywood 0 75F, min, Ibf/ft width
. 12.0-
ASTM D1970
Sealability around nail
pass
ASTMD1970
Waterproof 'integrity alter low temp
pass
flexibility
ASTM D1970
Waterproof integrity of lap seam
pass
ASTM D1970
Slip Resistance
pass ,
Co�IgN 02011 b/ Pdyghv U.SA., Ice ord dt egh• a•.,+ d
RGllron Coro, o•/Il • Ctt• HM
PRODUCT DATA
Approx Coverage (Nominal) ..........2 squares
Weight (Approx)............................. 70 lbs
Roll Size .................................... 65' x 36'
Rolls/Pallet...........................................20
APPLICABLE STANDARDS
• ASTM D 1970
• Miami Dade Code Compliance
• ICCESR-1697
• Florida Building Code Approved
WATRRPROOPINO MTRRIAW AND IN30UMO STRTRH9
my
C. &MbWN
,Jo v ,c�,o,,P
AGAS ram &S "
1-800-222-9782
www.polyglamixim
POLYSTICK° IR=Xe
APPLICATION INSTRUCTIONS
• Apply Polystick IRXe directly to the roof deck.
• Do not apply to shingles or other roof coverings.
• Apply only when the weather is dry and material interface temperatures (air, roof deck, membrane) are 40' F and rising.
• Always start at the lowest point of the roof deck where possible.
• Cut the Polystick IR-Xe to a suitable, workable length (typically between 9 and 15 feet).
• Lay the material flat in place, starting at the lowest point.
• Overlap seams 3' minimum and endlaps 6' minimum.
• Peel half of the backing off the roll and apply firm, even pressure from the center to the outer edges.
• Remove the backing from the remaining half of the roll and apply pressure.
• Always ensure that Polystick IRXe is applied over the area to cover the highest point of "ice damming'.
• Be sure to follow all local building code recommendations and requirements with regards to the width of ice dam materials.
• If full roof coverage application is desired, proper venting of the structure is required.
• Consult a design professional for proper venting requirements.
• In steep slope applications (i.e. 3:12 slope or higher) where backnoiling will be required, be sure that all nails are covered by the
overlapping next sheet.
• Polystick IR-Xe must be covered within 30 days of installation unless otherwise limited by local authorities.
MANUFACTURING FACILITIES
• Fernley, NV
• Hazleton, PA
• Winter Haven, FL
CORPORATE HEADQUARTERS
Polyglass U.S.A., Inc.
11 1 1 West Newport Center Drive
Deerfield Beach, FL 33442
v .polygloss.com
General Line: (88814101375
1954) 233-1330
Customer Service: (800) 222-9782
Technicol Service: (866) 802-8017
Quest ns? technical@polyglass.com
Product Disclaimer: Unless otherwse incorporated into or part of a supplemental manufacturers warranty, Polyglass w Mnts its pmducQs) against manufacturing
defects in Its product that directly results in leakage for a period of I year.
Refer to material safely data sheet (MSDS) for specific data and handling of our products. All
data furnished refers to standard production and is given in good faith within the applicable
NAMPBrOFINe MT S MD wsuwm c srsrevs
L
manufacturing and testing tolerances.
r
Polyglass U.S.A., Inc., reser es the right to improve and change its products at any time With,
notice. Polyglass U.S.A., Inc. cannot be held responsible for the use of its
M MADB
prior products
under conditions beyond its own control.
1-800.222.9782
For most current product data and warranty information, visit vvww.polyglass.com
www.polygtass.com
OFFICE USE ONLY:
DATE FILED: 7/16119
REVISION FEE:
PERIYRT # SLC 1907-0249
RECEIPT #
PLANNING & DEVELOPMENT SERVICES
BUILDING & CODE REGULATION DIVISION
2300 VIRGINIA AVENUE SCANNED
FORT PIERCE, FL 34982.5652 f�BY
(772) 462-1553 St ud eCi®U*
APPLICATION FOR BUILDING PERMIT REVISIONS
PROJECT INFORMATION
LOCATION/SITE
ADDRESS:
497 Sandia Avenue, Port St. Lucie, FL 34983
DETAILED DESCRIPTION OF PROJECT
CONTRACTOR INFORMATION:
STATE of FL REG./CERT. #: CCC1327420 ST. LUCIE CO CERT. #:
BUSINESS NAME: Ameri-Con Enterprises, Inc.
QUALIFIERS NAME. David Kielb
ADDRESS: 1466 SW San Sebastan Avenue
CITY: Port St. Lucie STATE: FL
PHONE (DAYTIME): 954- 44-7717 FAX:
OWNER/BUILDER INFORMATION:
NAME: Jodie Sweeney
ADDRESS:497 Sandia Avenue
C=: Port St. Lucie STATE: FL
PHONE. (DAYTIME: 754-281-4426 FAX:
ARCHITECT/ENGINEER INFORMATION:
NAME: _
ADDRESS:
CITY:
PHONE (DAYTIME):
STATE:
FAX:
ZIP: 34953
ZIP:
019
SLCCC. 9123109
Revised 06130/1701010"EVNE'3" -'�;
REVIEWED FOR f
CODE COMPLIANCE
M1AMt MiAMI-DADE COUNTY
ST LUCIE COUNTY
'
PRODUCT CONTROL SECTION
BOCjCj Aq�V11805
SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES.(RER)
Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miantidade.gov/economy
CertainTeed Corporation
18 Moores Road
Malvern, PA 19355
SCOPE:
File Copy
.�... .
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product. Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHD).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code. ;
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Flintlastic Self -Adhered Roofing Systems Over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in
the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
VERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it
11 be done in its entirety:
SPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall
available for inspection at the job site at the request of the Building Official.
NOA revises NOA #15-0108.03 and consists of pages 1 through 19.
submitted documentation was reviewed by Alex Tigera.
N:.
NOA No.: 15-0622.21
Expiration-Date:.04/13/20
Approval Date: 08/20/15
Pagel of 19
ROOFING ASSEMBLY APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Material:
SBS
Deck Type:
Wood
Maximum Design Pressure
-127.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Dimensions
Spec
Description
Flintlastic SA NailBase
391/8" x 66'6"; Roll
ASTM D 4601, Type
Fiberglass reinforced, SBS modified
weight: 821bs.
II
bitumen base sheet.
(2 squares)
All Weather/Empire Base
39 3/s" x 65' 10' ;
ASTM D 4601 Type
Asphalt coated, fiberglass reinforced base
Sheet
Roll weight: 70 lbs.
II
sheet.
(2 squares)
UL Type G2
Yosemite Venting Base
39 3/8" x 32' 10"; Roll
ASTM D 3909
Mineral Surfaced fiberglass reinforced
Sheet
weight: 95 lbs.
ASTM D 4897, Type
buffer sheet.
(1 square)
H
UL Type G3
Flexiglas Base Sheet
39 V x 98'9"; Roll
ASTM D 4601, Type
Modified Bitumen coated fiberglass base
weight: 90 lbs.
II
sheet.
(3 squares)
UL Type G2
Flintlastic Poly SMS Base
39 3/8" x 64' 3'; Roll
ASTM D 4601,
Modified, Bitumen coated polyester base
Sheet
weight: 90 lbs.
Grade S, Type lI
sheet.
(2 squares)
UL Type G2
Glasbase Base Sheet
39 3/8" x 98'9'; Roll
ASTM. D 4601 Type
Asphalt coated, fiberglass base sheet.
weight: 751bs.
II
(3 squares)
UL Type G2
Flintlastic Ultra Poly
39'/s" x 32' 10'; Roll
ASTM D 6164,
Smooth surfaced SBS Modified Bitumen
SMS Base Sheet
weight: 90 tbs.
Grade S, Type I
Membrane with non -woven polyester mat
(1 square)
reinforcement for mop applications.
Flintlastic SA PlyBase
39 %" x 66'6'; Roll
ASTM D 1970
Self -adhering, fiberglass reinforced, SBS
weight: 86 lbs.
modified bitumen base/ply sheet.
(2 squares)
Flintlastic SA Mid Ply
39 3/s" x 32' 1";
ASTM D 6163,
Self -adhering, polyester reinforced, SBS
Roll weight: 62 lbs.
Grade S, Type I
modified bitumen ply sheet
(1 square)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 2 of 19
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Flintlastic SA Cap FR
Flintlastic SA Cap FR
CoolStar
Flintlastic SA Cap
Flintlastic SA Cap
CoolStar
FlintPrime Asphalt
F1intPrime SA
Dimensions
Spec
Description
39 3/8" x 32' 11"; Roll
ASTM D 6163,
Self -adhering, fiberglass reinforced, SBS
weight: 88 lbs.
Grade G, Type I
modified bitumen cap sheet.
(1 square)
39 V x 32'11"; Roll
ASTM D 6163,
Self -adhering, fiberglass reinforced, SBS
weight: 90 lbs.
Grade G, Type I
modified bitumen cap sheet with
(1 square)
reflective coating.
391/8" x 32' 11'; Roll
ASTM D 6164,
Self -adhering, polyester reinforced, SBS
weight: 95 lbs.
Grade G, Type I
' modified bitumen cap sheet.
(1 square)
391/8" x 32'11'; Roll
weight: 98 lbs.
(1 square)
1, 3 or 5 gal pail
1, 3 or 5 gal pail
APPROVED INSULATIONS:
Product
F1intBoard ISO, FlintBoard ISOa
ACFoam-II
ENRGY3
H-Shield
Multi -Max FA-3
DensDeck, DensDeck Prime
SECUROCK Gypsum -Fiber Roof Board
ASTM D 6164, Self -adhering, polyester reinforced, SBS
Grade G, Type I modified bitumen cap sheet with
reflective coating.
ASTM D 41
Proprietary
TABLE 2
Product Description
Asphalt primer
Water -based, polymer modified primer.
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanurate insulation
Gypsum coverboard
homogenous fiber reinforced
Manufacturer
(with current NOA)
CertainTeed Corp.
Atlas Roofing Corp.
Johns Manville Corp.
Hunter Panels, LLC.
Rmax Operating, LLC.
Georgia Pacific Gypsum LLC.
USG Corp.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 3 of.19
APPROVED FASTENERS:
Fastener
Number
1.
2.
3.
4.'
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Product Name
Dekfast 14
Trufast #14 HD Fastener
#14 Roogrip .
OMG Heavy Duty
F1intFast #14 Fastener
Dekfast 12
#12 Standard Roofgrip
3 in. Round Metal Plate
Trufast #12 DP Fastener
F1intFast #12 Fastener
Dekfast Hex Plate
Flat Bottom Metal Plate
Trufast 3" Metal Insulation
Plate
FlintFast 3" Metal
Insulation Plate
TABLE 3
Product Description
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Insulation fastener
3" round galvalume AZ50
steel plate
Roofing screw
Roofing screw
hexagonal steel plate
3" square steel plate
3" round steel plate
3" round steel plate
Manufacturer
(with current NOA)
SFS Intec, hie.
Altenloh, Brinck & Co. U.S., Inc.
OMG, Inc.
OMG, Inc.
CertainTeed Corp.
SFS Intec, Inc.
OMG, Inc.
OMG, Inc.
Altenloh, Brinck & Co. U.S., Inc.
CertainTeed Corp.
SFS Intec, Inc.
OMG, Inc.
Altenloh, Brinck & Co. U.S., Inc.
CertainTeed Corp.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 4 of 19
APPROVED SURFACING/COATING OPTIONS:,
TABLE 4
Chosen components must be applied according to manufacturer's application instructions. Any coating, listed
below, used as a surfacing, must be listed within a current NOA.
System Manufacturer Application
Number
1. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
2. Generic Slag applied at 3001bs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
3. Karnak Corp. Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4. CertainTeed Corp. FlintCoat A-150 applied at an application rate of 1.5 gal/sq.
5. Gardner Asphalt Corp. APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6. Gardner Asphalt Corp. APOC #400 Sunbrite applied at an application rate of 3 gal✓sq.'
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 5 of 19
EVIDENCE SUBMITTED:
Test Aeencv
Test Identifier
Description
Date
Underwriters Laboratories
R11656
UL790
Annually
Momentum Technologies, Inc.
DX08C4A
Physical Properties
03/22/04
DX2OE3A
Physical Properties
03/22/04
Factory Mutual Research
3009610
FM 4450
10/15/01
2D5A9.AM
FM 4450
06/22/99
3014751
FM 4450
08/12/03
3014692
FM 4450
08/05/03
3012321
FM 4450
07/29/02
3008869
FM 4470
03/19/01
3037127
FM 4470
01/11/10
3039046
FM 4470
06/15/10
3048520
FM 4470
09/19/13
3025766
FM 4470
11/13/06
Trinity ERD
3518.12.03
TAS 114-F/G/I
12/O1/03
C3519.12.03-R1
TAS 114-D/J & TAS 117(B)
04/15/11
03515.07.03-1-R1
TAS 114-J & TAS 117(B)
06/27/12
3521.07.04
TAS 114-J & TAS 117(B)
07/28/04
3522.07.04
TAS 114-D
07/29/04
C31410.06.10
ASTM D 5147/4798
06/03/10
C7290.01.08
ASTM D 4601/1970
01/16/08
C8370.08.08-R1
TAS 114-HIJ & TAS 117(B)
10/05/09
C8500SC.11.07-R1
ASTM D 6862/TAS 117(B)
08/07/09
C30310.12.09
TAS 114 / TAS 117
12/17/09
C10080.09.08-R4
ASTM D 5147/6163/6164
03/25/10
ASTM D 6222/3909
C10080.09.10-R1
ASTM D 5147 & 6163
11/18/10
C30560.06.10
TAS 114 / TAS 117
06/10/10
C32830.07.10
FM 4470 / TAS 114
07/20/10
C32970.09.10
ASTM D 6163
09/16/10
3513.08.02-R1
TAS 114 / TAS 117
03/17/11
C32970.04.11
ASTM D 6164
04/O1/11
C35500.02.11
TAS 117(B)
02/09/11
C35460.05.11
ASTM D1876
06/16/11
045620.03.14
ASTM D1876, TAS 114 (H),
03/27/14
FM 4474
C47350.50.14
FM 4470
05/22/14
C44580.07.13
ASTM D 1876,
07/25/13
TAS 114, FM 4474
C42110.08.12
TAS 114 & TAS 117
08/13/12
PRI Construction Materials
CTC-034-02-01 REV
ASTM D 6163
11/24/08
Technologies
CTC-032-02-01
ASTMD6163
01/22/08
CTC-066-02-01
ASTM D6163
08/09/11
CTC-070-02-01
ASTM D6222
08/09/11
NOA No.: 15-0622.21
nwraaonoecourtn Expiration Date; 04/13/20
Approval Date: 08/20/15
Page 6 of 19
EVIDENCE SUBMITTED:
Test Agency
Test Identifier
Description
Date
CTC-093-02-01
ASTM D6164/4798
08/09/11
CTC-122-02-01
ASTMD2178
03/13/12
CTC-123-02-01
ASTM D2178
03/13/12
CTC-127-02-01
ASTM D4601
03/13/12
CTC-128-02-01
ASTMD6163
06/11/12
CTC-129-02-01
ASTMD6163
06/11/12
CTC-132-02-01
ASTM D6164
06/11/12
CTC-162-02-01
ASTM D6164
05/09/13
CTC-161-02-01
ASTM D6164
05/09/13
CTC-183-02-01
ASTM D6162
10/02/13
CTC-190-02-01
ASTM D6164
12/02/13
CTC-199-02-01
ASTMD1970
01/22/14
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 7 of 19
APPROVED ASSEMBLIES:
Membrane Type:
APP/SBS MODIFIED, SELF -ADHERING
Deck Type 1I:
Wood, Insulated
Deck Description:
19/32" or greater plywood or wood plank.
System Type A(1):
Anchor sheet mechanically fastened, optional top layer adhered with approved adhesive
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/ Empire Base Sheet, Yosemite Venting Base Sheet, Flexiglas Base
Sheet, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
mechanically attached as detailed below. i
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 8" o.c. at the 3" lap
and 8" o.c. in three, equally spaced center rows.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener'
able 3 Density/ft2
H-Shield, FlintBoardn ISO, ACFoam H, FlintBoard ISO, ENRGY 3 or Multi -Max FA-3
Minimum 1.5" thick N/A N/A
Top Insulation Laver (Optional) Insulation Fasteners Fastener
able 3 Density/ft2
DensDeck, DensDeck Prime
Minimum''%" thick N/A N/A
Note: Base insulation layer shall be adhered to the anchor sheet with TITESET Roofing Adhesive (3M
Polyurethane Foam Insulation Adhesive CR-20), Millennium One Step Foamable Adhesive, OlyBond 500,
OlyBond Green, Pliodeck or Insta-Stick spaced 4" o.c. Optional top layer of insulation shall be adhered to the
base layer with TITESET Roofing Adhesive (3M Polyurethane Foam Insulation Adhesive CR-20), Millennium
One Step Foamable Adhesive, 01yBond 500, OlyBond Green, Pliodeck or Insta-Stick spaced 6" o.c. Please refer
to Roofing Application Standard RAS 117 for insulation attachment.
Primer: Top insulation layer shall be primed with FlintPrime SA at a rate of 0.3 gallsquare.
Base Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid -Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR Coo]Star, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -52.5 psf (See General Limitation #7.)
NOA No.: 15-0622.21
FIT
M"l-DAD, COUNTY Expiration Date: 04/13/20 ME
Approval Date: 08/20/15
Page 8 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank.
System Type A(2): Anchor sheet mechanically fastened, optional top layer adhered with approved adhesive
All General and System Limitations apply.
Anchor. Sheet: One ply of All Weather/ Empire Base Sheet, Yosemite Venting Base Sheet, Flexiglas Base
Sheet, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
mechanically attached as detailed below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 8" o.c. at the 3" lap i
and 8" o.c. in three, equally spaced center rows.
One or more layers of any of the following insulations.
Base Insulation Laver
Insulation Fasteners Fastener
able 3 Densi /fe
H-Shield, FlintBoardu ISO, ACFoam II, FlinWoard I.SO, ENRGY 3 or Multi -Max FA-3
Minimum 1.5" thick N/A N/A
Too Insulation Laver
SECUROCK,Gypsum-Fiber Roof Board
Minimum''/a" thick
Insulation Fasteners Fastener
able 3 Density/ft'
N/A N/A
Note: Base insulation layer shall be adhered with THESET Roofing Adhesive (3M Polyurethane Foam Insulation
Adhesive CR-20) Millennium One Step Foamable Adhesive, OlyBond 500, OlyBond Green, Pliodeck or Insta-
Stick spaced 4" o.c. Top layer of insulation shall be adhered with TITESET Roofing Adhesive (3M Polyurethane
Foam Insulation Adhesive CR-20), Millennium One Step Foamable Adhesive, OlyBond 500, OlyBond Green,
Pliodeck or Insta-Stick spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation
attachment.
Primer: Apply Flint -Prime SA to SECUROCK Gypsum -Fiber Roof Board surface at 0.3 gal/square.
Base Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid -Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -60 psf (See General Limitation #7.)
NOA No.: 15-0622.21
MU1MI•DADE COUNTY Expiration Date: 04/13/20
...�
Approval Date: 08/20/15
Page 9 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1I: Wood, Insulated
Deck Description: Min 19/32" thick or greater plywood or wood plank at max 24" spans attached 6" o.c. using 8d
diameter ring shank nails,
System Type C(1): All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners
able 3
FlintBoard ISO, ACFoam 11, ENRGY 3, Multi -Max FA-3, H-Shield, FlintBoarda ISO
Minimum 1.5" thick N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density.
Too Insulation Laver
DensDeck
Minimum'/a" thick
Insulation Fasteners
able 3
1,2,3,4,5
Fastener
Densi /ft'
N/A
Fastener
Density/ft'
1:1.33 ft'
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Primer:
Base Sheet:
Ply Sheet:
(Optional)
Membrane:
Surfacing:
(Optional)
Maximum Design
Pressure:
Apply FlintPrime SA to DensDeck surface at 0.3 gal/square.
One or more layer of Flintlastic SA Mid Ply, self -adhered.
One or more layer of Flintlastic SA Mid Ply, self -adhered.
One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar self -adhered.
Any of the approved surfacing/coating options listed in Table 4.
-45 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 10 of 19
Membrane Type:
SBS MODIFIED, SELF -ADHERING
Deck Type 1I.
Wood, Insulated
Deck Description:
11/32" or greater plywood or wood plank.
System Type C(2):
All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver
Insulation Fasteners Fastener
able 3 Density/fe
FlintBoard ISO, ACFoam-II, ENRGY 3, Multi -Max FA-3, H-Shield, FlintBoardn ISO
Minimum 1.511 thick 6
1:1.45
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Primer: Apply FlintPrime SA to insulation surface at 0.3 gal/square.
Base Sheet: One or more layer of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -60 psf (See General Limitation #7.)
NOA No.: 15-0622:21
Mu MMADecounr Y Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 11 of 19
Membrane Type:
Deck Type 1:
Deck Description:
System Type E(1):
All General and System
Separation Sheet:
(Optional)
Anchor/Base Sheet:
Fastening:
Ply Sheet:
(Optional)
Membrane:
Surfacing:
(Optional)
Maximum Design
Pressure:
SBS MODIFIED, SELF -ADHERING
Wood, Non -Insulated
Deck 1: Min. 19/32" thick plywood attached using approved #�w
o.c. at wood joists spaced max. 24" o.c.
Deck 2: Minimum 19/32" thick plywood attached using approved
wood joists spaced maximum 24" o. c
JBase sheet mechanically fastened
it tions apply.
One more layers of Glasbase Base Sheet, loose laid.
6"
V o.c. at
One or mo layers of Flintlastic SA NailBase, mec cally attached as described below.
Anchor sheets 11 be fastened with FBC HVHZ ails and tin caps spaced 8" o.c. at the
4" lap and 8" o.o. ' three, equally spaced cente rows.
One or more layers of lintlastie SA P1yBas or Flintlastic SA Mid Ply, self -adhered.
One layer of Flintlastic SA 4, Flintl c SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR CoolS self eyed.
Any of the approved surfacing/coal,�fig options listed in Table 4.
For Deck 1: -52.5 psf (See Gqfieral LirXtation #7.)
For Deck 2: -60.0 psf (See grencral Limi lion #7.)
NOA No.: 15-0622.21 1
Expiration Date: 04/13/20
Approval -Date: 08/20/15 .
Page 12'of 19
Membrane Type:
Deck Type 1:
Deck Description:
SBS MODIFIED, SELF -ADHERING
Wood, Non -insulated
Minimum 19/32" thick plywood attached using 8d ring shank nails spaced 6"o.c. at wood joists
spaced maximum 24" o.c.
System Type E(2): Base sheet mechanically fastened.
All General and System Limitations apply.
Separation Sheet: One ply of GlasBase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Fastened with FBC HVHZ nails and tin caps spaced 6" o.c. at the 3" lap and 6" o.c. in four,
equally spaced staggered center rows.
Ply Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf (See General Limitation V.)
Pressure:
NOA No.: 15-0622.21
FRAMI-DADE Courts' Expiration Date: 04/13/20
Approval Date:. 08/20/,15
Page 13 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 11132" thick plywood at max 24" spans attached 6" o.c. using #8 wood screws.
System Type E(3): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Ba'se Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 6" o.c. at the 3"
lap and 6" o.c. in three, equally spaced center rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: - 75 psf (See General Limitation 47.)
I
4 NOA No.: 15-0622.21
MuAnronnecourrry Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 14 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 1 /32" thick plywood at max 24" spans attached 6" o.c. using #8 wood screws.
System Type E(4): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Base Sheet: One or more layers of Flintlastie SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with OMG #12 Standard Roofgdp with OMG 3 in. Round
Metal Plates spaced 8" o.c. at the 3" lap and 8 o.c. in two, equally spaced center rows.
Primer: Apply ASTM D41 primer to stress plates.
Ply Sheet: One or more layers of Flintlastic SA PiyBase or Flintlastie SA Mid Ply, self -adhered.
.(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: - 82.5 psf (See General Limitation V.)
NOA No.: 15-0622.21
M"uoane courm Expiration Date: 04/13/20
Approval Date: O8/20/15
Page 15 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -insulated
Deck Description: Minimum 11/32' thick plywood attached using #10 wood screws spaced 6"o.c. at wood joists
spaced maximum 24" o.c.
System Type E(5): Base sheet mechanically fastened.
All General and System Limitations apply.
Separation Sheet: One ply of GlasBase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: OMG 3 in. Round Metal Plates with OMG #14 Heavy Duty fasteners or TruFast 3" Metal
Insulation Plate with TruFast #12 DP or TruFast#14 HD Fasteners or F1intFast 3" Insulation
Plates with F1intFast #12 or FlintFast #14 Fasteners spaced 6" o.c. at the 4" lap and 6" o.c. in
three, equally spaced staggered center rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -97.5 psf (See General Limitation #7)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 16 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 19/32" thick plywood at max 24" spans attached 6 o.c. using #8 wood screws.
System Type E(6): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 4" o_c. at the 3"
lap and 4" o.c. in four, equally spaced center rows for a total of five rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed'in Table 4.
(Optional)
Maximum Design
Pressure: - 105 psf (See General Limitation V.)
I
NOA No.: 15-0622.21
rnnnn•DADE COUNTY Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 17 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -insulated
Deck Description: Minimum 19/32" thick plywood attached using #10 wood screws spaced 4"o.c. at wood joists
spaced maximum 24" o.c.
System Type E(7): Base sheet mechanically fastened.'
All General and System Limitations apply.
Separation Sheet: One ply of Glasbase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: OMG 3 in. Round Metal Plates with OMG #14 Heavy Duty fasteners or TruFast 3" Metal
Insulation Plate with TruFast #12 DP or TruFast #14 HD Fasteners or F1inTast 3" Insulation
Plates with F1intFast #12 or #14 Fasteners spaced 6" ox. at the 4" lap and 6" o.c. in four,
equally spaced staggered center rows.
Ply Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -127.5 psf. (See General Limitation #7)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 18 of 19
WOOD DECK SYSTEM LmTATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet_
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4: An overlay and/or recovery, board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping
with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each sidelap
and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not
acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of
either system shall be at a minimum rate of 12 lbslsq.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf, as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf insulation attachment shall not be acceptable.
6: Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system Should the
fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof
Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from
Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS
117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application
Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer,
Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this
NOA, General Limitation #9 will not be applicable.)
&. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform with
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended comers and comers). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 15-0622.21
MIAMFDADE COUNTY Expiration Date: 04f13/20
Approval Date: 08/20/15
Page 19 of 19
OFFICE USE ONLY:
DATE F LED: 02
REVISION FEE:
LOCATION/SITE
PERMIT # -'-4—C (q O 7
RECEIPT #
PLANNING & DEVELOPMENT SERVICES
BUILDING & CODE REGULATION DIVISION
2300 VIRGINIA AVENUE SCANNED
FORT PIERCE, FL 34982.5652 BY
(772)462-1553 aStlucieCoun$v
APPLICATION FOR BUILDING PERMIT REVISIONS
PROJECT INFORMATION
DETAILED DESCRIPTION OF PROJECT
Willy �sy►�� F ��
CONTRACTOR INFORMATION:
STATE of FL REG./CERT. #:
BUSINESS NAME:
QUALIFIERS NAbg.
CITY: Mir+, r>+. LA2CLt STATE:
PHONE (DAYTIME):
OWNER/BUILDER INFORMATION:
NAME:
CITY: frDr
PHONE (DA
ST. LUCIE CO CERT. #:
FAX:
P STATE: 7L�
p-qf � FAX:
ARCHITECT/ENGINEER INFORMATION:
NAME:
ADDRESS:
CITY:
PHONE (DAYTIME):
Off-
oi"-" �
SLCCC:9123109 t �' % 'a I
,§ Ar E�
Revised 06130117
File Copy
MIAMI-DADE COUNTY
MI " /`' J PRODUCT CONTROL SECTION
LqV �� �, I 11805 SW 26 Street, Room 208
DEPARTM 1 IF _ G A OR NOMIC RESOURCES (REp., Miami, Florida 33175-2474
BOARD ANDJot '.. I RATION DIVISION REVIEWED FOf7� (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) CODE COMPI I®NCIMW—vmiamidade.eov/economy
18 Moor eed Corporation
18 Moores Road ST. LUCIE CQUTY
Malvern, PA 19355 B0CCWJ
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: I IinU fic Self�Ad d Rooling Sy Ove—r— —9 Dec
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in
the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by
the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it
shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall
be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA #15-0108.03 and consists of pages 1 through 19.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page I of 19
i
ROOFING ASSEMBLY APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Material:
SBS
Deck Type:
Wood
Maximum Design Pressure
-127.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Dimensions
Spec
Description
Flintlastic SA NailBase
39 3/8" x 66'6'; Roll
ASTM D 4601, Type
Fiberglass reinforced, SBS modified
weight: 821bs.
II
bitumen base sheet.
(2 squares)
All Weather/Empire Base
39 3/e° x 65' 10' ;
ASTM D 4601 Type
Asphalt coated, fiberglass reinforced base
Sheet
Roll weight: 70 lbs.
II
sheet.
(2 squares)
UL Type G2
Yosemite Venting Base
39 3/s" x 32' 10'; Roll
ASTM D 3909
Mineral Surfaced fiberglass reinforced
Sheet
weight: 85 lbs.
ASTM D 4897, Type
buffer sheet.
(1 square)
lI
UL Type G3
Flexiglas Base Sheet
39 3/8" x 98'9'; Roll
ASTM D 4601, Type
Modified Bitumen coated fiberglass base
weight: 90 lbs.
If
sheet.
(3 squares)
UL Type G2
Flintlastic Poly SMS Base
39 3/8" x 64' 3'; Roll
ASTM D 4601,
Modified Bitumen coated polyester base
Sheet
weight: 901bs.
Grade S, Type II
sheet.
(2 squares)
UL Type G2
Glasbase Base Sheet
39 3/8" x 98'9"; Roll
ASTM D 4601 Type
Asphalt coated, fiberglass base sheet.
weight: 75 lbs.
II
(3 squares)
UL Type G2
Flintlastic Ultra Poly
39 3/8" x 32' 10'; Roll
ASTM D 6164,
Smooth surfaced SBS Modified Bitumen
SMS Base Sheet
weight: 90 lbs.
Grade S, Type I
Membrane with non -woven polyester mat
(1 square)
reinforcement for mop applications.
Flintlastic SA P1yBase
39 3/8" x 66'6'; Roll
ASTM D 1970
Self -adhering, fiberglass reinforced, SBS
weight: 86 lbs.
modified bitumen base/ply sheet.
(2 squares)
Flintlastic SA Mid Ply
39 3/8" x 32' 1";
ASTM D 6163,
Self -adhering, polyester reinforced, SBS
Roll weight: 62 lbs.
Grade S, Type I
modified bitumen ply sheet.
(1 square)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 2 of 19
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Flintlastic SA Cap FR
Flintlastic SA Cap FR
CoolStar
Flintlastic SA Cap
Flintlastic SA Cap
CoolStar
F1imPrime Asphalt
F1intPrime SA
Dimensions Spec Description
39 %" x 32'11'; Roll ASTM D 6163, Self -adhering, fiberglass reinforced, SBS
weight: 88 lbs. Grade G, Type I modified bitumen cap sheet.
(1 square)
39 3/8" x 32' 11' ; Roll ASTM D 6163, Self -adhering, fiberglass reinforced, SBS
weight: 901bs. Grade G, Type I modified bitumen cap sheet with
(1 square) reflective coating.
39 3/8" x 32' 11"; Roll
weight: 951bs.
(1 square)
39 3/s" x 32' 11"; Roll
weight: 98 lbs.
(1 square)
1, 3 or 5 gal pail
1, 3 or 5 gal pail
APPROVED INSULATIONS:
Product
F1imBoard ISO, F1imBoard ISOa
ACFoam-II
ENRGY 3
H-Shield
Multi -Max FA-3
DensDeck, DensDeck Prime
SECUROCK Gypsum -Fiber Roof Board
ASTM D 6164, Self -adhering, polyester reinforced, SBS
Grade G, Type I modified bitumen cap sheet.
ASTM D 6164, Self -adhering, polyester reinforced, SBS
Grade G, Type I modified bitumen cap sheet with
reflective coating.
ASTM D 41
Proprietary
TABLE 2
Product Description
Asphalt primer
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanurate insulation
Polyisocyanmate insulation
Gypsum coverboard
homogenous fiber reinforced
Water -based, polymer modified primer.
Manufacturer
(with current NOA)
CertainTeed Corp.
Atlas Roofing Corp.
Johns Manville Corp.
Hunter Panels, LLC.
Rmax Operating, LLC.
Georgia Pacific Gypsum LLC.
USG Corp.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 3 of 19
APPROVED FASTENERS:
Fastener
Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Product Name
Dekfast 14
Trufast #14 HD Fastener
#14 Roogrip
OMG Heavy Duty
F1intFast #14 Fastener
Dekfast 12
#12 Standard Roofgrip
3 in. Round Metal Plate
Trufast #12 DP Fastener
F1intFast #12 Fastener
Dekfast Hex Plate
Flat Bottom Metal Plate
Trufast 3" Metal Insulation
Plate
F1intFast 3" Metal
Insulation Plate
TABLE 3
Product Description
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Roofing screw
Insulation fastener
3" round galvalume AZ50
steel plate
Roofing screw
Roofing screw
hexagonal steel plate
3" square steel plate,
3" round steel plate
3" round steel plate
Manufacturer
(with current NOA)
SFS Intec, Inc.
Altenloh, Brinck & Co. U.S., Inc.
OMG, Inc.
OMG, Inc.
CertainTeed Corp.
SFS Intec, Inc.
OMG, Inc.
OMG, Inc.
Altenloh, Brinck & Co. U.S., Inc.
CertainTeed Corp.
SFS Intec, Inc.
OMG, :Inc.
Altenloh, Brinck & Co. U.S., Inc.
CertainTeed Corp.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 4 of 19
APPROVED SURFACING/COATING OPTIONS:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions. Any coating, listed
below, used
as a surfacing, must be listed within a current NOA.
System
Manufacturer
Application
Number
1.
Generic
Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
2.
Generic
Slag applied at 300 lbs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
3.
Karnak Corp.
Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4.
CertainTeed Corp.
FlintCoat A-150 applied at an application rate of 1.5 gal/sq.
5.
Gardner Asphalt Corp.
APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6.
Gardner Asphalt Corp.
APOC #400 Sunbrite applied at an application rate of 3 gal./sq.
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 5 of 19
EVIDENCE SUBMITTED:
Test Agencv
Test Identifier
Description
Date
Underwriters Laboratories
R11656
UL790
Annually
Momentum Technologies, Inc.
DX08C4A
Physical Properties
03/22/04
DX20E3A
Physical Properties
03/22/04
Factory Mutual Research
3009610
FM 4450
10/15/01
2D5A9.AM
FM 4450
06/22/99
3014751
FM 4450
08/12/03
3014692
FM 4450
08/05/03
3012321
FM 4450
07/29/02
3008869
FM 4470
03/19/01
3037127
FM 4470
01/11/10
3039046
FM 4470
06/15/10
3048520
FM 4470
09/19/13
3025766
FM 4470
11/13/06
Trinity ERD
3518.12.03
TAS 114-F/G/I
12/01/03
C3519.12.03-R1
TAS 114-D/J & TAS 117(B)
04/15/11
03515.07.03-1-R1
TAS 114-J & TAS 117(B)
06/27/12
3521.07.04
TAS 114-J & TAS 117(B)
07/28/04
3522.07.04
TAS 114-D
07/28/04
C31410.06.10
ASTM D 5147/4798
06/03/10
C7290.01.08
ASTM D 4601/1970
01/16/08
C8370.08.08-R1
TAS 114-H/J & TAS 117(B)
10/05/09
C8500SC.11.07-R1
ASTM D 6862/TAS 117(B)
08/07/09
C30310.12.09
TAS 114/TAS 117
12/17/09
C10080.09.08-R4
ASTM D 5147/6163/6164
03/25/10
ASTM D 6222/3909
C10080.09.10-R1
ASTM D 5147 & 6163
11/18/10
C30560.06.10
TAS 114/TAS 117
06/10/10
C32830.07.10
FM 4470 / TAS 114
07/20/10
C32970.09.10
ASTM D 6163
09/16/10
3513.08.02-R1
TAS 114/TAS 117
03/17/11
C32970.04.11
ASTM D 6164
04/O1/11
C35500.02.11
TAS 117(B)
02/09/11
C35460.05.11
ASTM D1876
06/16/11
C45620.03.14
ASTM D1876, TAS 114 (H),
03/27/14
FM 4474
C47350.50.14
FM 4470
05/22/14
C44580.07.13
ASTM D 1876,
07/25/13
TAS 114, FM 4474
C42110.08.12
TAS 114 & TAS 117
08/13/12
PRI Construction Materials
CTC-034-02-01 REV
ASTM D 6163
11/24/08
Technologies
CTC-032-02-01
ASTM D6163
01/22/08
CTC-066-02-01
ASTM D6163
08/09/11
CTC-070-02-01
ASTM D6222
08/09/11
NOA No.: 15-0622.21
htuuMi•oaoecounnv
Expiration Date: 04/13/20
Approval Date: O8/20/15
Page 6 of 19
EVIDENCE SUBMITTED:
Test Aaencv Test Identifier
Description
Date
CTC-093-02-01
ASTM D6164/4798
08/09/11
CTC-122-02-01
ASTM D2178
03/13/12
CTC-123-02-01
ASTM D2178
03/13/12
CTC-127-02-01
ASTM D4601
03/13/12
CTC-128-02-01
ASTM D6163
06/11/12
CTC-129-02-01
ASTM D6163
06/11/12
CTC-132-02-01
ASTM D6164
06/11/12
CTC-162-02-01
ASTM D6164
05/09/13
CTC-161-02-01
ASTM D6164
05/09/13
CTC-183-02-01
ASTM D6162
10/02/13
CTC-190-02-01
ASTM D6164
12/02/13
CTC-199-02-01
ASTMD1970
01/22/14
NOA No.: 15-0622.21
MtaMI-Daoecourm Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 7 of 19
APPROVED ASSEMBLIES:
Membrane Type:
APP/SBS MODIFIED, SELF -ADHERING
Deck Type 1I:
Wood, Insulated
Deck Description:
19/32" or greater plywood or wood plank
System Type A(1):
Anchor sheet mechanically fastened, optional top layer adhered with approved adhesive
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/ Empire Base Sheet, Yosemite Venting Base Sheet, Flexiglas Base
Sheet, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
mechanically attached as detailed below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 8"
o.c. at the 3" lap
and 8" o.c. in -three, equally spaced center rows.
One or more layers of any of the following insulations.
Base Insulation Laver
Insulation Fasteners
Fastener
Table 3
Density/ft2
H-Shield, FlintBoardn ISO, ACFoam H, FlintBoard ISO, ENRGY 3 or Multi -Max FA-3
Minimum 1.5" thick
NIA
N/A
Top Insulation Laver (Optional)
Insulation Fasteners
Fastener
Table 3
Density/fe
DensDeck, DensDeck Prime
Minimum'/<" thick
N/A
N/A
Note: Base insulation layer shall be adhered to the anchor sheet with TITESET Roofing Adhesive (3M
Polyurethane Foam Insulation Adhesive CR-20), Millennium One Step Foamable Adhesive, OlyBond 500,
OlyBond Green, Pliodeck or Insta-Stick spaced 4" o.c. Optional top layer of insulation shall be adhered to the
base layer with TITESET Roofing Adhesive (3M Polyurethane Foam Insulation Adhesive CR-20), Millennium
One Step Foamable Adhesive, OlyBond 500, OlyBond Green, Pliodeck or Insta-Stick spaced 6" o.c. Please refer
to Roofing Application Standard RAS 117 for insulation attachment.
Primer: Top insulation layer shall be primed with FlimPrime SA at a rate of 0.3 gal/square.
Base Sheet: One or more layers of Flintlastic SA P1yBase,or Flintlastic SA Mid -Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -52.5 psf (See General Limitation #7.)
MLAMMADE COUNTY
NOA No.: 15-0622.21
• • •, , Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 8 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type II: Wood, Insulated
Deck Description: 1 /32" or greater plywood or wood plank.
System Type A(2): Anchor sheet mechanically fastened, optional top layer adhered with approved adhesive
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/ Empire Base Sheet, Yosemite Venting Base Sheet, Flexiglas Base
Sheet, Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
mechanically attached as detailed below.
Fastening: Anchor sheet shall be fastened with FBC H VHZ nails and tin caps spaced 8" o.c. at the 3" lap
and 8" o.c. in three, equally spaced center rows.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
H-Shield, FGntBoardn ISO, ACFoam II, FlintBoard ISO, ENRGY 3 or Multi -Max FA-3
Minimum 1.5" thick N/A N/A
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft'
SECUROCK Gypsum -Fiber Roof Board
Minimum''/<" thick N/A N/A
Note: Base insulation layer shall be adhered with TITESET Roofing Adhesive (3M Polyurethane Foam Insulation
Adhesive CR-20) Millennium One Step Foamable Adhesive, OlyBond 500, OlyBond Green, Pliodeck or Insta-
Stick spaced 4" o.c. Top layer of insulation shall be adhered with TITESET Roofing Adhesive (3M Polyurethane
Foam Insulation Adhesive CR-20), Millennium One Step Foamable Adhesive, OlyBond 500, OlyBond Green,
Pliodeck or Insta-Stick spaced 6" o.c. Please refer to Roofing Application Standard RAS 117 for insulation
attachment.
Primer: Apply Flint -Prime SA to SECUROCK Gypsum -Fiber Roof Board surface at 0.3 gal/square.
Base Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid -Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -60 psf (See General Limitation #7.)
NOA No.: 15-0622.21
MIAMI•DAD; couMrr Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 9 of 19
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(1):
SBS MODIFIED, SELF -ADHERING
Wood, Insulated
Min 19/32" thick or greater plywood or wood plank at max 24" spans attached 6" o.c. using 8d
diameter ring shank nails.
All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners
Table 3
FlintBoard ISO, ACFoam H, ENRGY 3, Multi -Max FA-3, H-Shield, FlintBoarda ISO
Minimum 1.5" thick N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density.
Top Insulation Laver
DensDeck
Minimum'14" thick
Insulation Fasteners
Table 3
1,2,3,4,5
Fastener
Density/ft'
N/A
Fastener
Density/fe
1:1.33 W
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Primer: Apply F1intPrime. SA to DensDeck surface at 0.3 gal/square.
Base Sheet: One or more layer of Flintlastic SA Mid Ply, self -adhered.
Ply Sheet: One or more layer of Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: 45 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 10 of 19
Membrane Type:
SBS MODIFIED, SELF -ADHERING
Deck Type 1I:
Wood, Insulated
Deck Description:
19/32" or greater plywood or wood plank.
System Type C(2):
All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver
Insulation Fasteners Fastener
able 3 Densi /fe
FlintBoard ISO, ACFoam-H, ENRGY 3, Multi -Max FA-3, H-Shield, FlintBoarda ISO
Minimum 1.5" thick 6
1:1.45
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Primer: Apply F1intPrime SA to insulation surface at 0.3 gal/square.
Base Sheet: One or more layer of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -60 psf (See General Limitation V.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15 ,
Page 11 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Deck 1: Min. 11/32" thick plywood attached using approved #8 wood screws spaced 6"
o.c. at wood joists spaced max. 24" o.c.
Deck 2: Minimum 11/32" thick plywood attached using approved nails spaced 4" o.c. at
wood joists spaced maximum 24" o. c
System Type E(1): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One or more layers of Glasbase Base Sheet, loose laid.
(Optional)
Anchor/Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 8" o.c. at the
4 lap and 8" o.c. in three, equally spaced center rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR,
Flintlastic SA Cap FR CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design For Deck 1: -52.5 psf (See General Limitation #7.)
Pressure: For Deck 2: -60.0 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 12 of 19
Membrane Type: qB�MODIFIEE SI C-F=ADl-E1tiN
Deck Type 1: TWoW N06--insuIatet�
Deck Description: VInmum9z " -thii ly—w—qpllMjaic ed
s aced axummn- 4' o' o
System Type E(2): tase,shee�echAhic�lUMssteed
All General and System Limitations apply.
Separation Sheet: One ply of G1asBase Base Sheet, loose laid.
(Optional)
Base Sheet: ne ymore layers of Flintlastie S as mechanically attadhe� as descFibed lseloyv.
Fastening: Fastened with FBC HVHZ nails and tin caps spaced 6" o.c. at the 3" lap and 6" o.c. in four,
equally spaced staggered center rows.
Ply Sheet: [OSYe'ormage ayer� n a'sb 'SA P1-yBa e or-Flintlasfic S-A Mid-PlY;-Kelf-Idh-ered:W
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self-adbered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf (See General Limitation #7.)
Pressure:
r
1 TLOA Na:: 5--062214
E-ration Pate:-04/13/20
Approval -Date LNLl$
Page.-13f 1
F
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 19/32" thick plywood at max 24" spans attached 6" o.c. using #8 wood screws.
System Type E(3): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 6" o.c. at the 3"
lap and 6" o.c. in three, equally spaced center rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: - 75 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 14 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 11/32" thick plywood at max 24" spans attached 6" o.c. using #8 wood screws.
System Type E(4): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with OMG #12 Standard Roofgrip with OMG 3 in. Round
Metal Plates spaced 8" o.c. at the 3" lap and 8 o.c. in two, equally spaced center rows.
Primer: Apply ASTM D41 primer to stress plates.
Ply Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: - 82.5 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 15 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -insulated
Deck Description: Minimum 19/32" thick plywood attached using #10 wood screws spaced 6"o.c. at wood joists
spaced maximum 24" o.c.
System Type E(5): Base sheet mechanically fastened.
All General and System Limitations apply.
Separation Sheet: One ply of G1asBase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: OMG 3 in. Round Metal Plates with OMG #14 Heavy Duty fasteners or TruFast 3" Metal
Insulation Plate with TruFast #12 DP or TruFast #14 HD Fasteners or F1intFast 3" Insulation
Plates with FlintFast #12 or F1intFast #14 Fasteners spaced 6" o.c. at the 4" lap and 6" o.c. in
three, equally spaced staggered center rows.
Ply Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -97.5 psf. (See General Limitation #7)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 16 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -Insulated
Deck Description: Min 19/32" thick plywood at max 24" spans attached 6" o.c. using #8 wood screws.
System Type E(6): Base sheet mechanically fastened
All General and System Limitations apply.
Anchor/Base Sheet: One or more layers of Flintlastic SA NaiLBase, mechanically attached as described below.
Fastening: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 4" o.c. at the 3"
lap and 4" o.c. in four, equally spaced center rows for a total of five rows.
Ply Sheet: One or more layers of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self -adhered.
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap FR, Flintlastic SA Cap FR CoolStar,
Flintlastic SA Cap CoolStar self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: - 105 psf (See General Limitation #7.)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 17 of 19
Membrane Type: SBS MODIFIED, SELF -ADHERING
Deck Type 1: Wood, Non -insulated
Deck Description: Minimum 19/32" thick plywood attached using #10 wood screws spaced 4"o.c. at wood joists
spaced maximum 24" o.c.
System Type E(7): Base sheet mechanically fastened.
All General and System Limitations apply.
Separation Sheet: One ply of Glasbase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more layers of Flintlastic SA NailBase, mechanically attached as described below.
Fastening: OMG 3 in. Round Metal Plates with OMG #14 Heavy Duty fasteners or TruFast 3" Metal
Insulation Plate with TruFast #12 DP or TruFast #14 HD Fasteners or F1intFast 3" Insulation
Plates with FlintFast #12 or #14 Fasteners spaced 6" o.c. at the 4" lap and 6" o.c. in four,
equally spaced staggered center rows.
Ply Sheet: One or more layers of Flintlastic SA P1yBase or Flintlastic SA Mid Ply, self -adhered.
(Optional)
Membrane: One layer of Flintlastic SA Cap, Flintlastic SA Cap CoolStar, Flintlastic SA Cap FR or
Flintlastic SA Cap FR CoolStar, self -adhered.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design
Pressure: -127.5 psf. (See General Limitation #7)
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 18 of 19
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping
with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each sidelap
and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not
acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of
either system shall be at a minimum rate of 12 lbs./sq.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 Ibf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the
fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof
Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from
Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS
117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application
Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer,
Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this
NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform with
Roofing Application Standard RAS I I and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 15-0622.21
Expiration Date: 04/13/20
Approval Date: 08/20/15
Page 19 of 19