Loading...
HomeMy WebLinkAboutPOOL ITEMS PAPERWORK• ULTRATEMP° HEAT PUMPS HIGH PERFORMANCE HEAT PUMP 4� PEWTAIR r. •-100% pure titanium heal exchanger assures corrosion -free performance. pPh2nce for extra long lilc - - (iFl�°f &IACIeaCy • LCD control board displays an intuitive menu -driven readout with easy Solyoct Database to follow full word messages. -no more codes o) ocnrnw� • AuloSel [time clock over -ride) feature monitorswatertemperature and turns the water circulation pump on and off as needed to maintain desired pool temperatures • Automatic defrost feature senses refrigerant temperature and prevents freezing, allowing the heal pump to operate at even lower temperatures • Compatible with ALL automated control packages • Long -life corrosion resistant plastic composite cabinet stands up to severe climates and pool chemicals • Emerson- Copeland Scroll' Compressor on 60 Hz, single phase models • ETL listed for sale operation • Thermostatic Expansion Valve ITXVI controls refrigerant [low for optimum efficiency and BTU output over a wider operating range • Highest officiency available, meats or exceeds existing cc des and standards A1n�11n'fr;r,v, UltraTemp Heat Pumps • BTU and efficiency performance independently certified by the C�i✓ir'lNvNL40 industrys first heat pump charged with Air -Conditioning. Heating and Refrigeration Institute. AHIR - i3Y non -ozone depleting refrigerant, R410A. St. Lucie County Ordering Information P2110 Model 80/80/80• 80/63/80•1 50/63/80•• Fro Breaker BLACK ALMOND BTU/COP BTU/COP BTU/COP (Hz) Size Phase Wire Volt Ctn Ctn -A' (amp) Size Oty. Wt. Dim. 460960 460930 70 75.000/5.8 70.00015.7 50.000/4.1• 60 40 1 10 230 1 230 33.5 460961 460931 90 10.000/5.7 84,000/5.5 60.000/4.0 60 50 1 8 230 1 259 33.5 460962 460932 110 108,000/6.0 101.000/5.8 72.000/4.0 60 50 I 8 230 1 270 45.5 460963 460933 120 127.000/5.7 120,000/5.5 a82,000/6.0 60 50 1 8 230 1 270 45.5 0464�d60y,T4_14p 14 3,`Ogp/_ S736,pD07�6 pg;0110�4',0- b0 p�-}8-230T1'^g20 45.5', 460965 460935 120 H/C 127.000 Heal/5.6 120.00015.4 82,000/4.0 60 s0 1 8 230 1 278 45.5 71,000 Cool/4,1 460959 460958 140 H/C 140.000 Heat/5.6 80,000 Coel/4,1 132.000/5.4 85,000/4,0 60 50 1 8 230 1 320 34.5 N/A 460936 901 85.000/5.7 81.000/5.4 56,000/4.0 s0 30 3 10 380 1 250 33.5 460967 460937 120 C 123,000/5.6 115,000/5.3 81,000/4.0 60 50 3 8 230 1 280 45.5 N/A 460938 1001 102.00015.9 96,000/5.6 67,000A.0 50 50 1 8 230 1 280 41.5 460929 460928 140C 140.000/5.8 132.000/5.6 86,000/4.0 60 s0 3 8 230 1 320 45.5 ' Rating outside the scope Of ARI Standard 1160 fair temp. •F. / % relative humidity/water temp IF.] -• Rating in accordance with ARI Standard 1160 lair temp. •K/%relative humidity/water temp •F.1 Emerson -is a registered trademark of Emerson Electric Ca. and Copeland Scroll9is a registered trademark of Emerson Climate Technologies, Inc. Dimensions and Performance aE0 a The AHRI CertiffecIP Mark is appliepnly, to HVACR equipment and components that have been independently tested to certify manufacturers' performance claims are accurate. Visit www.ahridirectory.org for a complete list of certified products. CEC indicates that Heal Pump has been evaluated to California Tilte-20, listed in the California Energy Commission's ICECI database of compliant heat pumps, and certified to use on Residential swimming Pool Filtration Systems. See pages 453-454 for replacement parts. 2 ,INSTALLATION AND LOCATION OGAt IONr,' When pool equipment is located below the pool surface, a leak from any component can cause large scale water loss or flooding. Pentair Water Pool and Spa, Inc, cannot be responsible for such water loss or flooding which may cause damage to property or to the product. Avoid placing the heat pump in locations where it can cause damage by water or condensate leakage. if this is not possible, provide a suitable drain pan to catch and divert any leakage. vmy a quauned service person should install the UltraTemp® Heat Pump. Before installing this product, refer to the Important Warning and Safety Instructions on page if. Materials Needed for Installation The following items are needed and are to be supplied by the installer for all heat pump installations: 1. Plumbing connections (2-inch). 2. Level surface for proper drainage. 3. Suitable electrical supply line. See rating plate on unit for electrical specifications. Ajunction box is not needed at the heat pump; connections are made inside of the heat pump electrical compartment. Conduit may be attached directly to the heat pump jacket. 4. Electric cutout switch that will interrupt all power to the unit. This switch must be within line of sight of the heat pump. Check local codes for requirements. 5. Watertight conduit to run the electrical supply line. Equipment Pad Forproperdrainageof condensation and rainwater, place the heat pump on a flat slightly pitched surface, such as a concrete or fabricated slab (pad). If possible, place the pad at the same level or slightly higher than the filter system equipment pad. Note: Be sure that the pad is pitched not more than 1/4 in. per foot in any direction as needed for runoff. Heat Pump Dimensions MODELS DIMENSION "A" 70,90 33.5" (851 mm) 110, 120, 120C, 140C 45.5" (1156 ram) 120 H/C, 140,140 WC Drainage and Condensation Condensation occurs from the evaporator coil while the unit is running, and drains at a steady rate (usually three to five gallons per hour), depending upon ambient air temperature and humidity. The more humid the ambient conditions, the more condensation will be produced. The bottom of the unit acts as a tray to catch rainwater and condensation. Keep the drain holes, located on the bottom pan of the base of the unit, clear of debris. Roof Run-off Make sure the heat pump is not located where large amounts of water may run-off from a roof into the unit. Sharp sloping roofs without gutters will allow massive amounts of rain water, mixed with debris from the roof to be forced through the unit. A gutter or down spout may be needed to protect the heat pump. Lawn Sprinklers Avoid placing lawn sprinkler near the heater - they can spray water into the heater and void the warranty. Be sure to direct any spraying water away from the heater. Note the wind direction to be sure water from sprinklers is not blown toward the heater. Sprinkler heads can produce high water pressure and spray at an angle, different from typical rain and humid weather. Also, sprinklers connected to a well water system can cause mineral build up on the evaporator coils and electronics. Salt water can also be an issue if located near the coast. ULTRATEMP® Heat Pump InstatLation and Users Guide 'Location and Clearances All criteria given in the following sections reflect minimum clearances. However, each installation must also be evaluated, taking into account the prevailing local conditions such as proximity and height of walls, and _proximity to public access areas. The UltraTemp® Heat Pump must be placed to provide clearances on all sides for maintenance and inspection. 1. At least 24 in. [610 mm] access must be available in the front and 12 in. [305 mm] on all the other sides of the heat pump for service and proper air flow. (Manufacturer's recommendation). 2. If the heat pump is to be installed under a cover or under a vertical overhang, the unit must have a minimum of five (5) feet [1.52 m] clearance from the top of the heat pump. (Manufacturer's recommendation). 3. Install a minimum of five (5) feet 11.52 m] from the inside wall of the pool or spa unless the heat pump is separated from the pool or spa by a five (5) foot [1.52 m] high solid fence or other permanent barrier. Canadian installations require a minimum of three (3) meters 19.84 ft] from pool water. 4. Install heat pump a minimum of 6 in.1153 mm] from Heat Pump Location and Clearances Anchor Clamp Installation Installation of the anchor clamps is recommended in all installations. Installation of the anchor clamps is required in Florida (see Florida Building Code 301.13). Anchor clamps hold the heat pump to the equipment pad in order to withstand high winds caused during extreme weather (i.e. hurricanes). To install the anchor clamps: 1. Be sure the heat pump is in its permanent location on the equipment pad. Heat 2. Place the clamps at the base of the heat pump in Cis the four (4) locations, shown in the image to the right Note: Bolts and bolt anchors are not included with the heat pump. The installer must provide 1/4" x 1-3/9" stainless steel anchor bolts and the appro- priate size concrete anchor to mount the clamp to the equipment pad. Be sure to check local codes. 3. Fit the hook of each clamp over the lip on the base panel of the heat pump. The hook should fit between the lip of the base panel and the evapo- rator coil guard. Pump imps Anchor Clamp Installation ULTRATEMP® Heat Pump Installation and Users Guide `Anchor Clamp Installation, Continued 4. Mark the position of the hole in each clamp on the equipment pad. 5. Use a masonry drill bit and drill a hole in the cement with a diameter as determined by the concrete anchor, at each of the marks on the equipment pad. The hole should be approximately 1'h in. deep.- 6. Insert a bolt anchor into each of the holes. Be sure the anchors are set completely into the holes. 7. Position the anchor clamps so that the holes in the clamps are over the bolt anchors. Be sure that the clamp hooks are over the lip of the heat pump base. 8. InsertananchorboRthrough eachclamp intotheanchor and tighten to secure the clamp and heat pump to the equipment pad. o . C-000NCRETE - UIPMENiPBO d e II ®II .A-C:5. Anchor Clamp Installation CHEMU ORCHI TOPo.,..., Water Connections and Plumbing The image below shows the standard plumbing layout with a single UltraTemp® Heat Pump unit. Follow the image from right to left for the standard plumbing sequence. Arrangement of pool system components (other than the standard plumbing image below), and the location of the heat pump (above or below the pool water surface) can affect the operation of the heat pump's water pressure switch. The pressure switch can be adjusted to accommodate this effect if the heat pump water connections are no more than six (6) feet [1.82 m] below the pool water surface. See instructions for pressure switch adjustment on page 6. If the heat pump is installed outside of this range, an external pressure switch may need to be installed in the plumbing upstream of the heat pump. Note: Be advised that when pool equipment is located below the pool surface a leak can result in large-scale water loss orflooding. Pentair is not responsible forsuch water loss or flooding or damage. Automatic Flow Control Valve The inlettoutiet header of the heat pump comes equipped with an internal automatic flow control valve. The automatic flow control valve maintains the proper flow through the heat pump at rates up to 120 gpm (456 Ipm). If the filter system flow rate is higher than 120 gpm (456 Ipm), install a manual bypass valve, see image below. Note: Be advised that if your circulation pump is over 2 HP or if the total flow exceeds 120 gpm (456 Ipm), you will have to add an external bypass valve. Excess water flow will damage the heat exchanger. Standard Plumbing Layout ULTRATEMPO Heat Pump Installation and Users Guide 8/312017 SmartPo, -`Ir2 SolarPill Liquid Bail Solar Blanket Cover for Pool n 30,000 Gallons SmartPool AP72 SolarPill Liquid Ball Solar Blanket Cover for Pools up to 30,000 Gallons SKU: AP72 r1S—Wl l�1 4- View Larger Image SMARTPOOL About the SmartPool AP72 BY Si. Ludeftntv More Information The SmartPool SolarPill (SKU #AP72) is for pools up to 30,000 gallons The SolarPill is an innovative little product that packs a big punch. This and sds on your pool water's surface to help reduce heat and chemical thermally insulating liquid blanket slowly releases into your filtration. loss. system and forms a harmless, invisible barrier on the surface of your pool water to reduce heat and chemical loss by preventing water evaporation. Pool Cover Accessory Features' The advantage of this liquid solar blanket is that it is always working, even with swimmers in the water. One capsule heats 30,000 gallons for one • One SolarPill for every 30,000 gallons month. The SolarPill can be used with traditional chlorine, salt water and • Lasts up to one month mineral sanitizers. It is safe for use with all types of swimming pools and will not affect chemical balance. • Safe for use in a0 pool types and sanitization systems • Will not interfere with chemical balance ' z Non Tobc formula is safe foryour family and the environment http:/Niww.poolsupptywodd.comISmartPool-AP72SolorPill-Liquid-BallSolar-Bimket-Cover-forvPools-up-to-30000-GaOons/AP72.hhn 112 8131/2017 SmartPc'. 72 SolarPill liquid Ball Solar Blanket Cover for Pool " ' 0 30,000 Gallons SmartPool AP72 Specifications cover Type Dosage Item Quantity Manufacturer Pool Size Pool Type Product Type Solar Heating System Solar Cover 1 per 30,000 gallons Single SmartPool Up to 30,000 Gallons In Ground Pool Cover Accessory Solar Chemicals httplAvww.poolsupplywodd.comISmartPool-AP72SolarPill-Liquid-BallSolar-Blanket-Cover-for-Pools-up-to-30000-Gallons/AP72.hhn 212 SCA MD LIFE SAVER POOL FENCE SYSTEM SPECIFICATIONS - BY St. Lucie County General Description: Pool fence designed specifically to provide a barrier around residential swimming pools for toddlers and young children. Life Saver Pool Fence Systems ® does not have any gaps, openings, indentations, protrusions, or structural components that could allow a child to crawl under, squeeze through, or climb over the barrier. Our Perma Locking System" will not allow the barrier to be removed without the aid of tools. Life Saver Pool fence is manufactured and installed in compliance with the Florida Statutes, Florida Building Code R 4501.17.1, FBC/R 4502.17.1 , and ASTM D5034, ASTM D3787, ASTM G 53 System: Tension based system utilizing a series of 15 foot sections of fence with inserts for mounting in non -conducting polypropylene sleeves core drilled 4 inches deep into a concrete deck or other substantial surface, connected in series at the top with a spring loaded safety latch. One end of barrier requires tool to remove it. Non removal end secured to fence post and pool deck by a 1" L Brace for 360 applications. Non removal end secured by spring Perma Lock" with nut/bolt in screen enclosure applications. Construction: Mesh: Polyester mesh fabric with a mildew resistant polyvinyl coating to provide for years of use in direct sunlight. Continuous basket weave with a tensile strength rating of 270 lbs. per inch making it impossible to rip under normal use. Color selection is black, white, green or brown. Available in 48 or 60 in.heights. Bordered on all four sides by a reinforced vinyl material with a rating of 387 lbs. to prevent sagging providing the necessary tension to insure the fence's integrity. Marine Grade Stitching secures border to mesh. The mesh is pre - mounted on aluminum support poles and secured by aluminum cove molding strips. Poles: Reinforced 6063T6 I" Aluminum Poles are spaced no more than 36" apart. Temper rating of T6 scores the highest tensile strength (30ksi) within the 6063 alloy classification. Pole resistance to lateral pressure exceeds 70 lbs. of pressure before failure on any single pole in a free standing installation, thus exceeding the 52 lbs. of horizontal force prescribed by the Florida Building Code. Stainless steel roundhead screws (14) are utilized for securely attaching the aluminum cove molding to the poles and mesh. Surface of the poles are finished for handling and to prevent injuries from physical contact. Color options: black, white, green, tan, brown, bronze or silver finish. The poles are capped to provide a neat finished appearance. — — Revised 11/10/16 ,r � -1 ;, I Life Saver Pool Fence Systems, Inc. Removable Pool Safety Mesh Barrier Fencing Technical Specifications Life Saver Pool Fence Systems, Inc. has manufactured removable pool safety fencing for over 13 years and has continuously evolved their methods and materials, often -time leading industry wide changes. A Manufacturer's Limited Lifetime Warranty guarantees every system for as long as they own it. Life Saver Pool Fence meets and exceeds all code requirements throughout Florida. Below you will find technical specifications on the components used in assembling the Life Saver Pool Fence. Textilene Mesh Textilene mesh has been used as the highest quality material to the pool fence industry for over 15 years. Laboratory testing shows its strengths to surpass all code specifications and applicable ASTM standards. Item Number: Product Description: Fabric using .025" dia. vinyl -coated 1000 den. polyester core yarns in the warp and fill. I Attribute ASTM Warp Fill Typical Construction, end/inch D3775-96 13.0 ± .5 11.0 + .5 Weight, oz/yd2 D3776-96 -- -- 9.9 Tensile Strength (grab), Ibf D5034-95 221.4 213.3 Tensile Strength (strip), Ibf D5035-95 194.9 153.8 Tear Strength, (Trapezodial), Ibf D1117-97 65.4 54.0 Ball Burst, Ibf D3787-89 335 Bursting Strength, psi D3786-89 433 Elongation, % D5035-95 24.3 21.6 Abrasion Resistance D3884-92 No exposure of core yarn (CS10/500 cycles/ with no added weight) Flammability Rating CS-191-53 & CA 117E Weatherability, 1200 hours G53-96 No discoloration Mildew Resistance G21-96 No growth '• The above results are a representative of real data from single test samples. Presently no specification is incorporated. Warp refers to the horizontal threading while fill refers to the vertical threading. As shown, all testing confirms Textilene mesh meets and, on all strength tests, amply exceeds the set code requirements.