HomeMy WebLinkAboutNOAr-
q SCgNN�
REVIEWED FOR St. 4ay
'06cou�
CODE COMPLIANCE y MIAMbDADE �+�� v ML1MI-DADECOUNTY
ME ST. LUCIE COUNTYPRODUCTCONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (REaOCta 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION C {� -a�'" (�9 Miami, Florida 33175-2474
,- _ �_ _, . _ _ 1�.., t T (786) 315-2590 F (786) 315-2599
NOTICE OF
www.miamidade.eov/eeonomv
Boral Roofing LLC. NOV 2 120119
7575 Irvine Center Drive, Suite 100
Irvine, CA 92618 ST. Lucie County, Permitting File COPY
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: BORAL TileSeal
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This new NOA consists of pages 1 through 4.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 18-0502.03
MIAMFDADE COUNTY
F71T,=i7 Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 1 of 4
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: SBS
PRODUCTS DESCRIPTION:
Test
Product
Product Dimensions Specification
Description
BORAL TileSeal 36" x 36'
rolls TAS 103
SBS self -adhering asphalt sheet material with a
36" x 72'
rolls ASTM D 1970
white glass re -enforced polyester surfacing fabric;
for use as an underlayment in sloped roof
assemblies.
Boral Citadel Plus 36" x 72'
rolls ASTM D1970
SBS self -adhering asphalt sheet material with a
poly film -facer; for use as a mid -ply underlayment
in sloped roof assemblies.
MANUFACTURIGN LOCATION:
1. Brentwood, NH.
2. Houston, TX.
EVIDENCE SUBMITTED:
Test Agency
Test Identifier
Test Name/Report Date
PRI Construction Materials
OCF-356-02-04
ASTM D1623 07/25/18
Technologies, LLC.
OCF-356-02-02
TAS 103 07/24/18
OCF-356-02-01
ASTM D1970 07/26/18
OCF-424-02-04
ASTM D1623 07/25/18
OCF-424-02-01
ASTM D1970 07/25/18
OCF-424-02-03
TAS 103 07/25/18
Trinity ERD BRLRF-SC16810.11.17
ASTM D 1876 11/28/17
NOA No.: 18-0502.03
Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 2 of 4
APPROVED ASSEMBLIES:
Deck Type 1: Wood, non -insulated
Deck Description: 15/32" or greater plywood or wood plank
System E(1): Anchor sheet mechanically fastened deck, membrane adhered.
Base Sheet: One or more plies of ASTM D226 Type II or ASTM D2626 with a minimum 4" head lap and a
6" end lap mechanically fastened to deck with approved nails and tin caps 6" o.c. at the laps
and two staggered rows 12" o.c. the field of the roll.
Ply Sheet Apply one layer of Boral Citadel Plus over Base sheet as per current approval.
(Optional):
Membrane: One or more plies of BORAL TileSeal Underlayment with a minimum 3" head lap and
minimum 6" end lap. Place the first course of membrane parallel to the eave, rolling the
membrane to obtain maximum contact. Remove the release membrane as the membrane is
applied. Vertical strapping of the roof with BORAL TileSeal Underlayment is acceptable. All
end laps and laps without black selvage area shall be sealed under lap using an SBS modified
mastic.
Note: When used in Tile roof systems BORAL TileSeal Underlayment shall be back nailed to
deck with approved annular ring shank nails and tin caps at a maximum 12" o.c. at the side
laps. No nails or tin caps shall be exposed.
Surfacing: Approved for Adhered Roof Tile using TILE BOND or AH-160, Mechanically Fastened Roof
Tile, Metal Roofing, Wood Shake & Shingles, and Asphaltic Shingle assemblies.
MIAMIdMDE COUNTY NOA No.: 18-0502.03
F.T.N. � � Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 3 of 4
LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code. BORAL TileSeal underlayment shall be installed in strict compliance with applicable
Building Code.
3. BORAL TileSeal underlayment shall be applied to a smooth, clean and dry surface with deck free of irregularities.
4. BORAL TileSeal underlayment shall not be applied over an existing roof membrane as a recover, but may be
applied over a roofing Base/Anchor sheet underlayment.
5. BORAL TileSeal underlayment shall not be left exposed as a temporary roof for longer than 180 days of
application.
6. The standard maximum roof pitch for BORAL TileSeal underlayment shall be 6:12 when tiles are loaded directly
to the BORAL TileSeal underlayment; loading boards or battens are required on roof pitches greater than 6:12".
7. Refer to Prepared Roofing system Product Control Notice of Acceptance for listed approval of this product with
specific prepared roofing products.
8. Tiles shall be stored on battens on roof pitches greater than 6:12".
9. BORAL TileSeal underlayment may be used with any approved roof covering Notice of Acceptance listing
BORAL TileSeal underlayment as a component part of an assembly in the Notice of Acceptance. If BORAL
TileSeal underlayment is not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the
Miami -Dade County Product Control Department for approval provided that appropriate documentation is
provided to detail compatibility of the products, wind uplift resistance, and fire testing results.
10. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels. Sweep
the deck thoroughly to remove any dust and debris prior to application.
11. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane
from the center outward in both directions. For ridge applications, center the membrane and roll from the center
outward in both directions.
12. Roll or broom the entire membrane surface so as to have 100% contact with the surface, giving special attention to
overlap areas.
13. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
14. All protrusions or drains shall be initially taped with a 6" piece of underlayment. This target piece shall be pressed
in place and formed around the protrusion to ensure a tight fit. A second layer of BORAL TileSeal underlayment
shall be applied over the underlayment, and sealed using an SBS modified mastic.
15. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
16. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo, city
and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control Approved"
or the Miami -Dade County Product Control Seal as shown below
END OF THIS ACCEPTANCE
NOA No.: 18-0502.03
Expiration Date: 08/02/23
Approval Date: 08/02/18
Page 4 of 4
SCANNED
By
REVIEWED FOR St. Luce Cotinh
CODE COMPLIANCE MiAhu-DADE COUNTY
mm 07l . LUCIE C®UAtl 1 i PROD8 SW 6 Strreeet, RoomION 08
DEPARTMENT OF REGULATORY AND ECONOr\IIC RESOURCES SO C C Miami, Florida 33175-2474
BOARD AND CODE ADMll17STRATION DIVISION __ T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) RECEIVED_ ww%miamidade.eav/economy
Entegra Roof Tile, LLC
1289 NE 91h Ave
Okeechobee, FL 34972
NOV 21 's`9
ST. Lucie County, Permitting! File Copy
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHI (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Plantation Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA #14-1120.04 and consists of pages 1 through 7.
The submitted documentation was reviewed by Gaspar J Rodriguez,
NOA No:: 15-0721.04
Expiration Date:12108/20
Approval Date:11/05/15
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub -Category: Roofing Tiles
Material: Concrete
1. PRODUCT DESCRIPTION
Manufactured by Dimensions
Applicant
Plantation Tile Length: 16%2"
Width: 13"
Test Product
Specifications Description
TAS 112 Flat concrete roof tile for direct deck or
battened nail -on, mortar or adhesive set
applications.
Trim Pieces
L = varies TAS 112 Accessory trim, concrete roof pieces for
W = varies
use at hips, rakes, ridges
and val ley
Varying thickness
terminations. Manufactured for each tile
profile.
2.1. MANUFACTURING LOCATION
1. Okeechobee, FL
2.2 SUBMITTED EVIDENCE:
Test Agency
Test Identifier
Test Name/Report
Date
American Test Lab of South
RT0624.05-14
TAS 112
07/03/14
Florida
Redland Technologies
7161-03
Static Uplift Testing
Dec. 1991
Appendix III
PA 102 & PA 102(A)
The Center for Applied
94-060B
Static Uplift Testing
March, 1994
Engineering, Inc.
94-084
PA 101 (Adhesive Set)
May 1994
(Mortar Set)
Redland Technologies
7161-03
Wind Tunnel Testing
Dec. 1991
Appendix II
PA 108 (Nail -On)
Redland Technologies
Letter Dated Aug. 1, 1994
Wind Tunnel Testing
Aug. 1994
PA 108 (Nail -On)
Redland Technologies
P0631-01
Wind Tunnel Testing
July 1994
PA 108 (Mortar Set)
Redland Technologies
P0402
Withdrawal Resistance Testing of
Sept. 1993
screw vs. smooth shank nails
The Center for Applied
Project No.307025
Wind Driven Rain
Oct. 1994
Engineering, Inc.
Test #MDC-76
PA 100
Walker Engineering, Inc.
Calculations
Aerodynamic Multiplier
March 1999
April 1999
Walker Engineering, Inc.
Calculations
25-7183
March 1995
25-7094
February 1996
25-7496
April1996
NOA No.: 15.0721.04
Expiration Date:12/08120
Approval Date:11/05/15
Page 2 of 7
2.2 SUBMrrTED EVIDENCE:
Test Agency
Test Identifier
Test Name/Renort
Date
Walker Engineering, Inc.
Calculations
25-7584
December 1996
25-7804b-8
25-7804-4 & 5
25-7848-6
Walker Engineering, Inc.
Calculations
Two Patty Adhesive Set System
April 1999
Farabaugh Engineering and
T295.11
TAS-108
10/05/11
Testing Inc.
Farabaugh Engineering and
T306-I1
TAS-108
10/04/11
Testing Inc.
Farabaugh Engineering and
T279-11
TAS-108
09/23/11
Testing Inc.
3. LIMITATIONS
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test
in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami -Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building
Code and Rule 61 G20-3 of the Florida Administrative Code.
NOA No.:15-0721.04
MIAMI-DADECOU Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 3 of 7
4. INSTALLATION
4.1 Plantation Roof Tile and its components shall be installed in strict compliance with Roofing Application
Standard RAS 118, RAS 119 and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight (W) and Dimensions (1 x w )
Tile Profile
Weight-W (Ibf)
Length-[ (ft)
Width-w (ft)
Plantation Tile
11.6
1,375
1.08
Table 2: Aerodynamic Multipliers - A. (ft3)
Tile
Profile
2. (ft3)
Batten Application
2. (ft3)
Direct Deck Application
Plantation Tile
0.267
0.289
Table 3: Restoring Moments due to Gravity - M (ft-Ibf)
Tile
Greater than
Profile
2"; 12"
3",12'
4": 12'
51: 12"
6": 12"
7": 12"
Battens
Direct
Battens
I Direct
Battens
I Direct
Battens
Direct
Battens
Direct
Battens
Direct
I Deck
I Deck
I Deck
Deck
Deck
Deck
Plantation
7.22
7.91
6.85
7.79
6.75
7.67
6.61
7.52
6.44
7.32
6.26
7.04
Tile
NOA No.:15-0721.04
MIAMI-DADE COUNTY
. . , i Expiration Date:12/08/20
Approval Date:11105/15
Page 4 of 7
Table 4: Attachment Resistance Expressed as a Moment - Mr (ft-Ibf)
For Nall -On Systems
Tile
Fastener Type
Direct Deck
Direct Deck
Battens
Profile
(Min 16132"
(Min. 19132"
plywood)
plywood)
Plantation Tile
2-10d Ring Shank
30.9
38.1
17.2
Nails
1-10d Smooth or
7.3
9.8
4.9
Screw Shank Nail
2-10d Smooth or
14.0
18.8
7.4
Screw Shank Nails
1 #8 Screw
30.8
30.8
18.2
2 #8 Screw
51.7
51.7
24.4
1-10d Smooth or
24.3
24.3
24.2
Screw Shank Nail
Field Clip)
1-10d Smooth or
19.0
19.0
22.1
Screw Shank Nail
Eave Clip)
2-10d Smooth or
35.5
35.5
34.8
Screw Shank Nails
Field Clip)
2-10d Smooth or
31.9
31.9
32.2
Screw Shank Nails
Eave Clip)
2-10d Ring Shank
60.3
65.5
48.3
Nails'
1 Installation with a 4" tfle headIsp and fasteners are located a minimum of 2%' from the head of tile.
Table 5: Attachment Resistance Expressed as a Moment Mf (ft-Ibf)
For Two Patty Adhesive Set Systems
Tile Profile
Tile Application
Minimum Attachment
Resistance
Plantation Tile
Adhesive
31.33
2 See manufactures component approval for installation requirements.
3 Flexible Products Company'HeBond Average weights, per patty 13.9 grams.
310- 2-Component Foam Roof Tile Adhesive AH-160. Average weight per patty 8 Prams.
Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-Ibf)
For Single Patty Adhesive Set Systems
Tile Profile
Tile Application
Minimum Attachment Resistance
Plantation Tile
3M " 2-Component Foam Roof Tile Adhesive AR-160
118.94
3R-- 2-Componant Foam Roof Tile Adhesive AH-1601
40.45
4 La r a paddy placement of 45 grams of 3M" 2-Component Foam Roof The Adhesive AH-160
5 Medium paddy placement of 24 grams of 3W 2-Component Foam Roof Tile Adhesive AH-160.
NOA No.: 15-0721.04
Expiration Date:12/08/20
Approval Date: 11/05/15
Page 5 of 7
Table 7: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)
for Mortar Set Systems
Tile Profile Tile Application Attachment
Resistance
Seespecific mortar manufacturer's Notice of Acceptance.
5. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or following
statement: "Miami -Dade County Product Control Approved".
PLANTATION ROOF TILE LABEL (LOCATED ON UNDERSIDE OF TILE
6. BUII.DING PERMIT REQUMEMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
NOA No.: 15-0721.04
Expiration Date:12/08/20
Approval Date: 11/05/15
Page 6 of 7
PROFILE DRAWING
PLANTATION FLAT CONCRETE TILE
END OF THIS ACCEPTANCE
NOA No.: 15-0721.04
Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 7 of 7