HomeMy WebLinkAboutNOAsr. LucIE COUNTY
SCANNED
BUILDING DIVISION
BY
REVIEWED
FOR COMPLI E
St. Lucie County
�Y
WED BY '
.2.
L
MIAMI•DADE PLANS AND PER IT
MIAMI-DADE COUNTY
E UST BE KEPTON JOBOR
PRODUCT CONTROL SECTION
INSPECTION WILL BE MADE
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMI
R) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION
T (786)315-2590 F (786) 31525-99
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.-govIeconomv
Johns Manville Corporation
717 17th Street
Denver, CO SCOPE: 80202 FILE
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the
Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County
Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade
County) reserve the right to have this product or material tested for quality assurance purposes. If
this product or material fails to perform in the accepted manner, the manufacturer will incur the
expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such
product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it
is determined by Miami -Dade County Product Control Section that this product or material fails to
meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code including the High Velocity Hurricane Zone of the Florida Building Code.
DE�CRIP ION.','Johns 1VIiinville Modified Blfuinen RoofingSystemsoveY Conci•efeD'ecks: r,
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state
and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted
herein.
RENEWAL of this NOA shall be considered after a renewal application has been Sled and there has
been no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or
change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an
endorsement of any product, for sales, advertising or any other purposes shall automatically terminate
this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of
NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and
followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is
displayed, then it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No. 13-0129.20 and consists of pages 1 through 44.
The submitted documentation was reviewed by Jorge L. Acebo.
THESE PLANS AND ALL PRPOWD WORK NOA No.: 13-0529.19
MIA MADE COUNTY ARE SUBJECT TO Y ECTIONS Expiration Date: 07/19/16
F.M.REQUIRED BY PIELD i1i3RS THAT Approval Date: 03/06/14
MAY BE NEC At N ORM TO Page I of 44
COMPLY WITH ALL ICABLE CODES.
ROOFING SYSTEM APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Materials:
SBS
Deck Type:
Concrete
Maximum Design Pressure:
-536.5 psf.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions Specification
Description
DynaBase
39-3/8" x 49'2" ASTM D6163
A glass..reinforced SBS modified bitumen
Type I Grade S
base sheet.
DynaBase PR
39-3/8" x 49'2" ASTM D6164
A polyester reinforced SBS modified
Type I Grade S
bitumen base sheet.
DynaWeld Base
39-3/8" x 32' 10" ASTM D6163
A glass reinforced SBS modified bitumen
Type I Grade S
base sheet for heat welded applications.
DynaBase HW
39-3/8" x 49'2" ASTM D6163,
A glass reinforced SBS modified bitumen
Type I Grade S
base sheet for heat welded applications.
DynaWeld 180 S
39-3/8" x 32' 10" ASTM D6164
A polyester reinforced SBS modified
Type I Grade S
bitumen base or inner ply sheet for use in
heat weld applications.
DynaWeld Cap FR
39-3/8" x 32' 10" ASTM D6163
A fire resistant, polyester reinforced SBS
CR
Type I Grade G
modified bitumen membrane surfaced with
granules and a white reflective coating for
use in heat weld applications.
DynaGlas FR CR
39-3/8" x 32' 10' ; ASTM D6163
A fire resistant, glass reinforced SBS
Type I Grade G
modified bitumen membrane surfaced with
granules and a white reflective coating.
DynaGlas
39-3/8" x 32' 10" ASTM D6163
A glass reinforced SBS modified bitumen
Type I Grade G
membrane surfaced with granules.
DynaWeld Cap FR
39-3/8" x 32' 10" ASTM D6163
A fire resistant, glass reinforced SBS
Type I Grade G
modified bitumen membrane surfaced with
granules for use in heat weld applications.
DynaWeld Cap 180
39-3/8" x 32' 10" ASTM D6164
A fire resistant, polyester reinforced SBS
FR
Type I Grade G
modified bitumen membrane surfaced with
granules -for use in heat weld applications.
Dyn ,as --180'
39-3/8" x 49'2" ASTM D6164
A polyester reinforced SBS modified
bitumen base or inner ply sheet.
DynaFast 180 HW
39-3/8" x 49'2" ASTM D6164
A polyester reinforced SBS modified
bitumen base or inner ply sheet for use in
heat weld applications.
DynaFast 250 HW
39-3/8" x 32' 10" ASTM D6164
A polyester reinforced SBS modified
bitumen base or inner ply sheet for use in
heat weld applications.
DynaWeld Cap 250
39-3/8" x 32' 10" ASTM D6164
A fire resistant, polyester reinforced SBS
FR
Type II Grade G
modified bitumen membrane surfaced with
granules for use in heat weld applications.
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 2 of 44
Product
DynaWeld Cap 250
FR CR
DynaWeld Cap 250
DynaWeld 250 S
DynaGlas 30 FR
DynaGlas FR
DynaKap TI
DynaKap FR TI
DynaLastic 180
DynaLastic 180 FR
DynaLastic 180 S
DynaWeld 180 S
DynaPly Tl
DynaLastic 250 FR
DynaLastic 250 FR
-CR - -
Dimensions
39-3/8" x 32' 10"
Test
Specification
Product
Description
ASTM D6164 A fire resistant, polyester reinforced SBS
Type II Grade G modified bitumen membrane surfaced with
39-3/8" x 32' 10" ASTM D 6164
Type II Grade G
39-3/8" x 32' 10" ASTM D 6164
Type II Grade S
39-3/8" x 32'10"
39-3/8" x 32' 10"
39-3/8" x 32' 10"
39-3/8" x 32' 10"
39-3/8" x 32' 10"
39-3/8" x 32' 10"
ASTM D6163
Type I Grade G
ASTM D6163
Type I Grade G
ASTM D6162
Type I Grade G
ASTM D6162
Type I Grade G
ASTM D6164
Type I Grade G
ASTM D6164
Type I Grade G
39-3/8" x 32' 10" ASTM D6164
Type I Grade S
39-3/8" x 32' 10" ASTM D6162
Type I Grade S
39-3/8" x 32' 10" ASTM D6162
39-3/8" x 32' 10".
Type I Grade S
ASTM D6164
Type II Grade G
39-3/8" x 32' 10" ASTM D6164
Type II Grade G
DynaLastic 250 S
39-3/8" x 32' 10" ASTM D6164
Type II Grade S
DynaMax FR
39-3/8" x 32' 10" ASTM D6162
Type III Grade G
DynaMax S
39-3/8" x 32' 10" ASTM D6162
Type III Grade S
MIAMI•DADE COUNTY
,...8 1
granules and a reflective white coating for
use in heat weld applications.
A polyester reinforced SBS modified
bitumen membrane surfaced with granules
for use in heat weld applications.
A polyester reinforced SBS modified
bitumen base or inner ply sheet for use in
heat weld applications.
A fire resistant, glass reinforced SBS
modified bitumen membrane surfaced with
granules.
A fire resistant, glass reinforced SBS
modified bitumen membrane surfaced with
granules.
A composite reinforced SBS modified
bitumen membrane surfaced with granules.
A fire resistant, composite reinforced SBS
modified bitumen membrane surfaced with
granules.
A polyester reinforced SBS modified
bitumen membrane surfaced with granules.
A fire resistant, polyester reinforced SBS
modified bitumen membrane surfaced with
granules.
A polyester reinforced SBS modified
bitumen base or inner ply sheet.
A composite reinforced SBS modified
bitumen base or inner ply sheet for use in
heat weld applications.
A composite reinforced SBS modified
bitumen base or inner ply sheet.
A fire resistant, polyester reinforced SBS
modified bitumen membrane surfaced with
granules.
A fire resistant, polyester reinforced SBS
modified bitumen membrane surfaced with
granules and a reflective white coating.
A polyester reinforced SBS modified
bitumen base or inner ply sheet.
A fire resistant, composite reinforced SBS
modified bitumen membrane surfaced with
granules.
A composite reinforced SBS modified
bitumen base or inner ply sheet.
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 3 of 44
Test
Product
Product
Dimensions
Specification
Description
DynaClad
39-3/8" x 33' 10"
ASTM D6298
A glass reinforced base sheet SBS
modified bitumen membrane surfaced with
foil.
DynaBase XT
39-3/8" x 49'2"
ASTM D6163
A glass reinforced SBS modified bitumen
Type I Grade S
base or inner ply sheet.
DynaGlas FR XT
39-3/8" x 32' 10"
ASTM D6163
A fire resistant, glass reinforced SBS
Type I Grade S
modified bitumen membrane surfaced with
granules.
G1asKa' -'
36" x 36'
ASTM D3909
A mineral surfaced, asphalt coated,
fiberglass cap sheet.
GlasKap CR
36" x 36'
ASTM D3909
A white mineral surfaced, white acrylic
coated, fiberglass cap sheet.
Ventsulation Felt
36" x 36'
ASTM D4897
Heavy duty fiber glass base sheet
Type II
impregnated and coated on both sides with
asphalt with or without fine mineral
stabilizer. Surfaced on the bottom side
with coarse mineral granules embedded in
asphaltic coating.
GlasBase Plus
36" x 108'
ASTM D4601
Type 1I asphalt impregnated and coated
glass fiber base sheet for use in
conventional and modified bitumen built-
up roofing.
GlasPly IV
36" x 200'
ASTM D2178
Type IV asphalt impregnated glass felt for
Type IV
use in conventional and modified bitumen
built-up roofing.
GlasPly Premier
36" x 180'
ASTM D2178
Type VI asphalt impregnated glass felt for
Type VI
use in conventional and modified bitumen
built-up roofing.
PermaPly 28
36" x 108'
ASTM D4601
Type II asphalt impregnated and coated
Type II
glass fiber base sheet for use in
conventional and modified bitumen built-
up roofing.
FesCant Plus Cant
various
ASTM C728
Factory pre -fabricated cant strips and taper
Strips, and Taper
edge, manufactured from expanded perlite
Edge
insulation.
MBR Flashing
N/A
Proprietary
A two component elastomeric, cold
Cement Base and
application adhesive, consisting of a
Activator -
-
modified proprietary compound with an
asphalt base.
MBR Bonding
N/A
Proprietary
A two component urethane cold
Adhesive
application adhesive.
MBR Cold
5, 55, and 350 gal,
ASTM D3019
One part, elastomeric cold application
Application Adhesive
Type III
adhesive
MBR Low VOC
5 gal
Proprietary
One part, asphalt modified urethane
Membrane Adhesive
adhesive
MBR RA Membrane
1.5L Cartridge
Proprietary
Two part, cold process membrane adhesive
Adhesive
NOA No.: 13-0529.19
MIAMI-DADE COUNTY
Expiration Date: 07/19/16
""0 1
Approval Date: 03/06/14
Page 4 of 44
Test
Product
Product
Dimensions Specification
Description
JM Urethane
N/A Proprietary
Urethane insulation adhesive.
Insulation Adhesive
JM Two Part
N/A Proprietary
A two-part urethane insulation adhesive
Urethane Insulation
Adhesive
Bestile Industrial
various ASTM D4586
A trowel grade, cutback bitumen flashing
Roof Cement
Type I
grade cement mixture including inorganic
fibers and mineral stabilizers.
Flex -I -Drain
various BOCA 76-61
Two piece flexible drain system composed
SBCCI 89204
of a Noryl deck flange, a flexible neoprene
UBC 3236
bellows and no hub connection. Available
in various sizes and styles for most Retro-
Fit Board applications.
PC/PET RetroDrain
various N/A
Engineered resin copolymer fabricated
drain for retrofit applications.
USII RetroDrain
various N/A
One piece, aluminum fabricated drain for
retrofit applications.
Superpome
various N/A
Cast aluminum, heavy-duty drain for
RetroDrain
retrofit applications.
FP-10 Vents
10" deck flange, N/A
One-way roof vent, designed for use in
base diameter of 4"
various roof systems, for the release of
and a height of 6"
pressure created by gases or moisture
vapor trapped within the roofing system.
Expand-O-Guard
various N/A
Elastomeric expansion joint cover for
vertical expansion and seismic joints.
Manufactured from non -reinforced, form -
supported elastomeric bellows with a
bifurcated waterproof attachment to metal
flanges.
Expand-O-Flash
various N/A
Expansion joint covers manufactured from
non -reinforced, form -supported
elastomeric bellows with a bifurcated
waterproof attachment to metal flanges.
Presto-Lok Fascia
various TAS 114
A multi -piece fascia and flashing system
and Flashing System
for built-up and modified bitumen roofing
systems manufactured from aluminum or
steel.
DynaTred &
_
various N/A
Preformed, skid -resistant boards.
DynaTred Plus Roof
Walkway
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 5 of 44
APPROVED INSULATIONS:
Product Name
ENRGY 3, ENRGY 3 25 PSI,
ValuTherm, ValuTherm 25 PSI,
R-Panel, R-Panel 25 PSI
TABLE 2
Product Description
Polyisocyanurate Insulation.
ENRGY 3 AGF, ENRGY 3 AGF 25 Isocyanurate Insulation with glass
PSI, ENRGY 3 CGF, ENRGY 3 reinforced facers
CGF 25 PSI, ValuTherm AGF,
ValuTherm AGF 25 PSI,
ValuTherm CGF, ValuTherm CGF
25 PSI
Manufacturer
(With Current NOA)
Johns Manville
Johns Manville
ENRGY 3 FR
Isocyanurate Insulation with inorganic
Johns Manville
coated glass reinforced facers; bottom face
is premium coated for combustible decks.
Fesco Foam, DuraFoam
Polyisocyanurate Insulation with perlite
Johns Manville
facer
Retro-Fit Board, DuraBoard
High -density perlite roof insulation.
Johns Manville
Fesco Board
Rigid perlite roof insulation board.
Johns Manville
JM SECUROCK Gypsum -Fiber
Rigid, gypsum -based board stock
Johns Manville
Roof Board
APPROVED FASTENERS:
TABLE 3
Fastener Product
Product
Manufacturer
Number Name
Description Dimensions
(With Current NOA)
1. All Purpose Fastener
Insulation fastener for # 14 x 16" max.
Johns Manville
concrete decks. length; 43 Phillips
head
2. Structural Concrete
Insulation fastener for Various
Johns Manville
Fastener
concrete decks.
3. UltraFast 3" Round
Galvalume AZ55 3" round
Johns Manville
Metal Plate or UltraFast
steel plate 3" square
- Square Recessed Metal
Plate
4. UltraFast Plastic Plate
High Density 3" round
Johns Manville
Polyolefin round plate
5. UltraFast ASAP
Pre -assembled Various
Johns Manville
Insulation fastener
and plate
6. High Load Fasteners and # 15 fasteners and 20 2-3/8" round
Johns Manville
Plates
gauge metal plates
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 6 of 44
EVIDENCE SUBMITTED:
Test Agency/Identifier
Factory Mutual Research Corp.
Dynatech Engineering, Inc.
Underwriters Laboratories, Inc.
Exterior Research & Design,
LLC
TrinityjERD
Independent Roof Testing &
Consultants of South Florida
IRT-ARCON Inc.
Name
3001482
3001629
OZ8A9.AM
3D4A4.AM
3000949
3007148
3006346
3001457
3009499
3011248
3014090
3012974
3020703
3037222
3026130
J037540
3012064
4360.03.95-1
4360.03.95-2
4361.5.95-1
R10167
04361-2.04.97-1
# 10390A-10.97-1
#10390A-12.97-1
#4251.08.96-1
10391.01.03
02843.02.05-10-R1
00257.03.05-1
02843.02.07
J7670.06.08
J6990.12.07-R1
J 17040.1 l .09-RI
J 13700.05.10-1-R l
J13700.05.10-2
IRT 99006
IRT 99007
IRT 99008
IRT 99016
IRT 99009
IRT 99010
02-026
02-011
Report
FM 4470
FM 4470
FM 4470
FM 4470
FM 4470
FM 4450
FM 4450
FM 4470
FM 4470
FM 4470
FM 4470
FM 4450
FM 4470
FM 4470
FM 4470
FM 4470
FM 4470
TAS 114
TAS 114
TAS 114
UL 790
TAS 114
TAS 114
TAS 114
TAS 114
TAS 114
TAS 114
ASTM D6162/D6163
ASTM D6164/D6298
TAS 114
ASTM D3909
ASTM D6162/D6164
ASTM D6164
ASTM D5147/D6163
ASTM D5147/D6164
Date
08/11/98
09/ 10/98
09/10/98
09/28/98
06/05/98
04/ 19/00
09/ 15/00
03/04/02
04/04/01
11/O1/02
09/05/02
06/03/02
07/30/04
10/02/09
04/26/09
10/20/10
06/25/02
03/95
03/95
05/95
05/27/ 13
04/28/97
10/97
12/97
O1/20/99
01/29/03
02/07/07
03/17/05
02/07/07
06/16/08
03/24/10
03/11/10
O1/25/11
05/11/10
TAS 114
01/20/99
TAS 114
01/20/99
TAS 114
01/20/99
TAS 114
01/20/99
TAS 114
02/10/99
TAS 114
02/10/99
TAS 114 07/26/02
TAS 114 02/06/02
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 7 of 44
EVIDENCE SUBMITTED: (CONTINUED)
Test Agency/Identifier
Name
Report
Date
PRI Construction Materials
JMC-066-02-01
ASTM D6163
06/04/12
Technologies, LLC
JMC-065-02-01
ASTM D6163
05/29/12
JMC-070-02-01
ASTM D2178 Type IV
04/17/12
JMC-071-02-01
ASTM D2178 Type VI
04/17/12
JMC-072-02-01
ASTM D4601 Type II
06/14/12
JMC-074-02-01
ASTM D4897 Type II
04/17/12
JMC-075-02-04.2
ASTM D5147/D6164 Type II
12/27/13
JMC-078-02-01
ASTM D5147/D6298
07/17/12
JMC-081-02-01.02
TAS 117 B & C
06/11/12
JMC-091-02-01
ASTM D4601 Type 1
06/04/12
JMC-093-02-01
ASTM D4601 Type II
08/02/12
JMC-105-02-01
ASTM D5147/D6162
05/22/13
JMC-107-02-01 Rev 4
ASTM D903
11/04/13
ASTM D1876
ASTM D5147
TAS 117(B)
TAS 117(A)
TAS 114(C)
JMC-171-02-01
ASTM D6163
01/10/14
JMC-171-02-02
ASTM D6163
01/10/14
JMC-171-02-10
ASTM D6162
01/10/14
JMC-171-02-03
ASTM D6164
01/10/14
Atlantic & Caribbean
ACRC 06-009
TAS 114-D
06/28/06
Roofing Consultants, LLC
NOA No.: 13-0529.19
MIAMI•DADE COUNTY Expiration Date: 07/19/16
"' y m Approval Date: 03/06/14
Page 8 of 44
APPROVED ASSEMBLIES
Membrane Type: SBS
Deck Type 3I: Concrete Decks, Insulated
Deck Description: 2500 psi structural concrete or concrete plank
System Type A(1): One or more layers of insulation adhered with approved asphalt or adhesive.
All General and System limitations apply.
One or more layers of the following insulations:
Base Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ft2
ENRGY 3, ENRGY 3 25 PSI, ValuTherm, ValuTherm 25 PSI, R-Panel, R-Panel 25 PSI, ENRGY 3
AGF, ENRGY 3 AGF 25 PSI, ValuTherm AGF, ValuTherm AGF 25 PSI, ENRGY 3 AGF,
ENRGY 3 AGF 25 PSI, ValuTherm AGF, ValuTherm AGF 25 PSI
Minimum 1.5" thick
Fesco Foam, DuraFoam
Minimum 1.5" thick
Top Insulation Layer (Optional)
Fesco Board, DuraBoard
Minimum %" thick
Retro-Fit Board
Minimum''/2" thick
N/A N/A
N/A
N/A
Insulation Fasteners
Fastener
(Table 3)
Density/ft2
N/A N/A
N/A N/A
Note: All insulation shall be adhered to the primed deck in full mopping of approved hot asphalt
within the EVT range and at a rate of 20-40 lbs./100 ft2. Please refer to Roofing Application
Standard RAs 117 for insulation attachment.' Insulation listed as base layer only shall be used only
as base layers with a second layer of approved top layer insulation installed as the final membrane
substrate. Composite insulation panels may be used as a top layer placed with the
polyisocyanurate side facing down.
Base Sheet: (Optional) One ply of GlasPly Premier, GlasPly IV or PermaPly 28 Base Sheet
adhered in a full mopping of approved asphalt applied within the EVT range and at
a rate of 2040 lbs./sq.
Ply Sheet: One or more plies of GlasBase Plus, PermaPly 28, GlasPly Premier, GlasPly IV,
DynaLastic 180 S, DynaFast 180 S, DynaLastic 250 S, DynaBase, DynaBase PR,
DynaBase XT, DynaMax S or DynaPly T I adhered to the base sheet with
approved mopping of asphalt applied within the EVT range and at a rate of 2040
lbs./sq. or one ply DynaWeld Base, DynaBase HW, DynaWeld 180 S, DynaFast
180 HW, DynaWeld 250. S or DynaFast 250 HW heat welded.
MIAMI-DADE COUNTY
..0
NOA No.: 13-0529.19
Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 9 of 44
Membrane: One ply of DynaGlas FR CR, DynaKap, DynaKap FR T 1, DynaMax FR,
DynaGlas, DynaGlas FR, DynaGlas 30 FR, DynaGlas FR XT, DynaLastic 180,
DynaLastic 180 FR, DynaLastic 180 S, DynaLastic 250 FR, DynaLastic 250 FR
CR or DynaPly TI adhered in a full mopping of approved asphalt applied within
the EVT range and at a rate of 20-40 lbs./sq. or one ply DynaWeld Cap FR CR,
DynaWeld Cap FR, DynaWeld Cap 180 FR, DynaWeld Cap 250, DynaWeld Cap
250 FR or DynaWeld Cap 250 FR CR heat welded. (See application instructions
for approved method of installation).
Or
(Only with a modified Base or Ply sheet) GlasKap or GlasKap CR adhered in a
full mopping of approved asphalt applied within the EVT range and at a rate of 20-
40 lbs./sq.
Surfacing: (Optional) Install one of the following:
1. Flood coat and gravel/slag with an application rate of 60 lbs./sq. & 400
lbs./sq., respectively.
Maximum Design
Pressure: -305 psE (See General Limitation 99).
NOA No.: 13-0529.19
MIAMI•DADE COUNTY Expiration Date: 07/19/16
Approval Date: 03/06/14
Page 10 of 44
IMN
"oni,
7c..
I
40U�7T®Y ,
DEPARTMENT OFREGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786)315-2590 F (786) 31525-99
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
Johns Manville Corporation
717 17th Street
Denver, CO 80202
SCOPE:
SCANNED
BY
St. Lucie County
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product
Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County)
reserve the right to have this product or material tested for quality assurance purposes: If this product or
material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing
and the AHJ may immediately revoke, modify, or suspend the use of such product or material within
their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade
County Product Control Section that this product or material fails to meet the requirements of the
applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code including the High Velocity Hurricane Zone of the Florida Building Code.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and
following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no
change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in
the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of
any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to
comply with any section of this NOA shall be cause for termination and removal of NOA. -
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No. 12-0203.04 and consists of pages 1 through 39.
The submitted documentation was reviewed by Jorge L. Acebo.
MIAMI•DADE COUNTY
THESE PLANS AND ALL I
ARE SUBJECT TO ANY
REQUIRED BY PIEL MI
MAY BE AtEC W
COMPLY INITHAL AP
15 THAT NOA No.: 13-0129.16
i TO Expiration Date: 07/19/16
Approval Date: 06/27/13
CODES. Page I of 39
ROOFING SYSTEM APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Materials:
SBS
Deck Type:
Lightweight Concrete
Maximum Design Pressure:
-105 psf.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions Specification
Description
DynaBase
54'-10" x 36" ASTM D6163
An SBS modified bitumen coated, fiber
Type I Grade S
glass reinforced base sheet.
DynaWeld Base
39'-3/8" x 32'-10" ASTM D6163
An SBS modified bitumen coated,
Type I Grade S
fiberglass reinforced base sheet for heat
welded applications.
DynaWeld 180 S
39-3/8" x 32'-10" ASTM D6164
An elastomeric modified bitumen coated,
Base
Type I Grade S
nonwoven polyester mat and bi-
directional glass scrim reinforced, base
sheet for heat welded applications.
DynaWeld Cap FR
39'-3/8" x 32'-10" ASTM D6163
A fire resistant, cool roof (CR), SBS
CR
roll. Type I Grade G
modified bitumen membrane surfaced
weight: 120 lbs.
with granules for heat weld applications.
DynaGlas FR CR
39-3/8" x 32'-10'; ASTM D6163"A
`A fire"iesistant,` cool roof (CR), SBS
roll Type I Grade G
modified bitumen membrane surfaced
weight: 101 lbs.
with granules for application in hot
asphalt.
DynaGlas
39-3/8" x 32'-10" ASTM D6163
An SBS modified bitumen membrane
Type I Grade G
surfaced with granules for application in
hot asphalt.
DynaWeld Cap FR
39'-3/8" x 32'-10" ASTM D6163
A fire resistant SBS modified bitumen
Type I Grade G
membrane surfaced with granules for heat
weld applications.
DynaWeld Cap 180
39-3/8" x 32'-10" ASTM D6164
A fire resistant, polyester reinforced, SBS
FR
Type I Grade G
modified bitumen sheet.
DynaGlas 30 FR
39-3/8" x 32'-10" ASTM D6163
A fire resistant SBS modified bitumen
Type I Grade G
membrane surfaced with granules for
—application
in hot -asphalt. --- -
DynaGlas FR
39-3/8" x 32'-10" ASTM D6163
A fire resistant SBS modified bitumen
Type I Grade G,
• membrane surfaced with granules for
application in hot asphalt.
DynaKap Tl
39-3/8" x 32'-10" ASTM D6162
A fiberglass/polyester reinforced SBS
Type I Grade G
modified bitumen membrane surfaced
with granules for application in hot
asphalt.
DynaKap FR Tl
39-3/8" x 32'-10" ASTM D6162
A fire resistant, fiberglass/ polyester
Type I Grade G
reinforced SBS modified bitumen
membrane surfaced with granules for
application in hot asphalt.
NOA No.: 13-0129.16
MIAMI•DADE COUNTY
Expiration Date: 07/19/16
""9 1
Approval Date: 06/27/13
Page 2 of 39
Test
Product
Product
Dimensions Specification
Description
DynaLastic 180
39-3/8" x 32'-10" ASTM D6164
A polyester reinforced SBS modified
Type I Grade G
bitumen membrane surfaced with
granules for application in hot asphalt.
DynaLastic 180 FR
39-3/8" x 32'-10" ASTM D6164
A 180 gram polyester mat reinforced,
Type I Grade S
granular -surfaced, modified bitumen cap
sheet for use in fire -rated systems.
DynaLastic 180S
37" x 36'-9" ASTM D6164
A 180 gram polyester mat reinforced,
Type I
modified bitumen cap sheet for use in
fire -rated systems.
DynaPly Tl
39-3/8" x 32'-10" ASTM D6162
A polyester reinforced SBS modified
Type II, Grade S
bitumen ply sheet for use in conventional
and modified bitumen built-up roof
systems.
DynaLastic 250
39-3/8" x 32'-10" ASTM D6164
A 250 gram polyester mat reinforced,
Type II Grade G
granular -surfaced, modified bitumen cap
sheet.
DynaLastic 250 FR
39-3/8" x 32'-10" ASTM D6164
A 250 gram polyester mat reinforced,
Type II Grade G
granular -surfaced, modified bitumen cap
sheet for use in fire -rated systems.
DynaMax FR
39-3/8" x 32'-10" ASTM D6162
A fire, resistant, fiberglass/ polyester
Type III Grade G
reinforced SBS modified bitumen
membrane surfaced'with granules for
application in hot asphalt.
DynaClad
39-3/8" x 33'-6" ASTM D6298
A foil faced, glass reinforced, SBS
modified membrane for application in hot
asphalt.
DynaBase XT
39-3/8" x 49'-2" ASTM D6163
A heavyweight glass reinforced SBS
Type I Grade S
Base/Ply sheet.
DynaGlas FR XT
39-3/8" x 32'-10" ASTM D6163
A heavyweight glass reinforced granular
Type I Grade S
surfaced SBS Cap sheet.
G1asKap
36" x 36' ASTM D3909
A mineral surfaced, asphalt coated,
fiberglass cap sheet.
G1asKap CR
36" x 36' ASTM D3909
A white mineral surfaced, white acrylic
coated, fiberglass cap sheet.
Ven_ tsulation Felt
36" x_ 36' ASTM D4897
Heavy duty fiber glass base sheet
Type II
impregnated and coated on both sides
with -asphalt with -or -without- fine mineral— ---- ---
stabilizer. Surfaced on the bottom side
with coarse mineral granules embedded in
asphaltic coating.
GlasBase Plus
36" x 108' ASTM D4601
Type II asphalt impregnated and coated
glass fiber base sheet for use in
conventional and modified bitumen built-
up roofing.
GlasPly IV
36" x 180' ASTM D2178
Type IV asphalt impregnated glass felt
Type IV
for use in conventional and modified
bitumen built-up roofing.
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 3 of 39
jam.. V
Test
Product
Product
Dimensions Specification
Description
GlasPly Premier
36" x 180' ASTM D2178
Type VI asphalt impregnated glass felt
Type VI
for use in conventional and modified
bitumen built-up roofing.
PermaPly No. 28
36" x 106' ASTM D4601
Type fl asphalt impregnated and coated
Type II
glass fiber base sheet for use in
conventional and modified bitumen built-
up roofing.
FesCant Plus Cant
various ASTM C728
Factory pre -fabricated cant strips and
Strips, and Taper
taper edge, manufactured from expanded
Edge
perlite insulation.
MBR Flashing
N/A Proprietary
A two component elastomeric, cold
Cement Base and
application adhesive, consisting of a
Activator
modified proprietary compound with an
asphalt base.
MBR Bonding
N/A Proprietary
A two component urethane cold
Adhesive
application adhesive.
Bestile Industrial
various ASTM D4586,
A trowel grade, cutback bitumen flashing
Roof Cement
Type I
grade cement mixture including inorganic
fibers and mineral stabilizers.
Flex -I -Drain
various BOCA 76-61
Two piece flexible drain system
SBCCI 89204
composed of a Noryl deck flange, a
UBC 3236
flexible neoprene bellows and no hub
connection. Available in various sizes
and styles for most retro-fit applications.
PC/PET RetroDrain
various N/A
Engineered resin copolymer fabricated
drain for retrofit applications.
USII RetroDrain
various N/A
One piece, aluminum fabricated drain for
retrofit applications.
Superpome
various N/A
Cast aluminum, heavy-duty drain for
RetroDrain
retrofit applications.
FP-10 Vents
10" deck flange, base N/A
One-way roof vent, designed for use in
diameter of 4" and a
various roof systems, for the release of
height of 6"
pressure created by gases or moisture
---
vapor- trapped within the -roofing -system.--
Expand-O-Guard
various N/A
Elastomeric expansion joint cover for
vertical expansion and seismic joints.
Manufactured from non -reinforced, form -
supported elastomeric bellows with a
bifurcated waterproof attachment to metal
flanges.
Expand-O-Flash
various N/A
Expansion joint covers manufactured
from non -reinforced, form -supported
elastomeric bellows with a bifurcated
waterproof attachment to metal flanges.
NOA No.: 13-0129.16
MIAMI•DADE COUNTY Expiration Date: 07/19/16
rRy • . 1 Approval Date: 06/27/13
Page 4 of 39
Test Product
Product Dimensions
Specification Description
Presto-Lok Fascia various
TAS 114 A multi -piece fascia and flashing system
and Flashing System
for built-up and modified bitumen roofing
systems manufactured from aluminum or
steel.
DynaTred & various
N/A Preformed, skid -resistant boards.
DynaTred Plus Roof
Walkway
APPROVED INSULATIONS:
TABLE 2
Product Name
Product Description Manufacturer
(With Current NOA)
ENRGY 3
Polyisocyanurate Insulation. Johns Manville
Fesco Foam, DuraFoam
Polyisocyanurate Insulation with perlite Johns Manville
facer
Retro-Fit Board, DuraBoard
High -density perlite roof insulation. Johns Manville
Fesco Board
Rigid perlite roof insulation board. Johns Manville
APPROVED FASTENERS:
TABLE 3
Fastener Product
Product Manufacturer
Number Name
Description Dimensions (With Current NOA)
I. Twin Loc-Nail
Base sheet fastener with 2.7" dia. Plate ES Products, Inc.
integrated Plate.
2. AccuTrac Plate
Galvalume AZ50 steel plate 3" square OMG, Inc.
3. Lightweight Concrete
Galvanized double spreading 1.2" or 1.7" Johns Manville
(LWC) CR Base Fastener leg fastener for securing base leg length;
sheets to lightweight 2.7" dia. Plate
insulating concrete.
4. U1traFast Fastener
Insulation fastener for wood, various Johns Manville
steel and concrete.
5. CR Base Sheet Fastener
Galvanized double spreading 1.2" or 1.7" OMG,Inc.
L7
Ieg-fastener -for- securing -base— leg -length; — — --
sheets to lightweight 2.7" dia. Plate
insulating concrete.
6. Ultralok
Base sheet fastener with 2.7" dia. Plate Johns Manville
integral plate
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 5 of 39
EVIDENCE SUBMITTED:
Test Agency/Identifier
Name
Report
Date
Underwriters Laboratories, Inc.
R10167
UL 790
05/27/13
Factory Mutual Research Corp.
3001482
FM 4470
08/11/98
3001629
FM 4470
09/10/98
OZ8A9.AM
FM 4470
09/10/98
3D4A4.AM
FM 4470
09/28/98
3009499
FM 4470
04/04/01
107A4.AM
FM 4470
11/09/98
3007148
FM 4450
04/19/00
3006346
FM 4450
09/15/00
3001457
FM 4470
03/04/02
3012974
FM 4450
06/03/02
3014090
FM 4470
09/05/02
3011248
FM 4470
11/01/02
3026130
FM 4470
04/26/09
Exterior Research & Design, LLC
#4361-2.04.97-1
TAS 114
04/28/97
#4361-2.04. -1
TAS 114
04/00/97
#10390A-10.97-1
TAS 114
10/00/97
#10390A-12.97-1
TAS 114
12/00/97
#4251.08.96-1
TAS 114
01/20/99
00257.03.05-1
ASTM D6162/D6163
03/17/05
ASTM D6164/D6298
TrinitylERD
02843.02.07
TAS 114
02/07/07
J7670.06.08
ASTM D3909
06/16/08
J6990.12.07-R1
ASTM D6162/D6164
03/24/10
J17040.11.09
ASTM D6164
11/16/09
J13700.05.10-1-R1
ASTM D5147/136163
01/25/11
J13700.05.10-2
ASTM D5147ID6164
05/11/10
10391.01.03
TAS 114
01/29/03
Independent Roof Testing &
IRT99001
TAS 114
01/20/99
Consultants of South Florida
IRT99002
TAS 114
01/20/99
IRT99003
TAS 114
01/20/99
IRT99005
TAS 114
01/20/99
—IRT99013--
TAS"1-14—
01/20/99
Atlantic & Caribbean Roof
ACRC 03012
TAS 114
12/04/03
Consulting, LLC
ACRC 03015
09/30/03
ACRC 07-014
04/18/07
IRT-ARCON Inc.
02-011
TAS 114
02/06/02
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 6 of 39
EVIDENCE SUBMITTED: (CONT.)
Test Agency/Identifier
Name
PRI Construction Materials
JMC-066-02-01
Technologies, LLC
JMC-065-02-01
JMC-070-02-01
JMC-071-02-01
JMC-072-02-01
JMC-074-02-01
JMC-075-02-04
JMC-078-02-01
JMC-081-02-01.02
JMC-091-02-01
JMC-093-02-01
JMC-105-02-01
Report
Date
ASTM D6163
06/04/12
ASTM D6163
05/29/12
ASTM D2178 Type IV
04/17/12
ASTM D2178 Type VI
04/17/12
ASTM D4601 Type II
06/14/12
ASTM D4897 Type II
04/17/12
ASTM D5147/D6164 Type II
08/03/12
ASTM D5147/D6298
07/17/12
TAS 117 B & C
06/11/12
ASTM D4601 Type I
06/04/12
ASTM D4601 Type II
08/02/12
ASTM D5147/D6162
05/22/13
Type III, Grade G
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 7 of 39
APPROVED ASSEMBLIES
Membrane Type: SBS
Deck Type 4I: Lightweight Concrete, Insulated
Deck Description: Concrecel Cellular Lightweight Concrete
System Type A(1): Anchor sheet mechanically fastened; one or more layers of insulation adhered with
approved asphalt.
Deck: 18-22 ga steel deck shall be secured 6" o.c. to structural supports spaced a
maximum of 5 ft. on centers with 5/8" puddle welds. Followed by Concrecel
Bonding agent applied to the deck at rate 1200 sq. ft./gal using a compressed air
sprayer. Rigid insulation panels shall be placed in a minimum'/4" slurry -coat of
insulating concrete and allowed to cure overnight. The following day the rigid
insulation shall be covered with a minimum 2'/4" topcoat cast of Concrecel. After
an additional cure time of 24 hours Concrecel Curing Compound was roller
applied at a rate of 300 sq. ft./gal.
All General and System limitations apply.
Anchor Sheet:neTpLkCrlasPlz3Pr'_etp er PermaPly 28 or Ventsulation fastened to the deck as
described below:
Fastening: Fasten base sheet to deck with 7M LWC CR Base Fasteners or OMG CR Base
Sheet Fasteners 1.7 at the 3" side lap 7" o.c. and 7" o.c. in two staggered rows in
the center of the sheet
Base Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/ftr
ENRGY 3
Minimum 1" thick N/A N/A
Fesco Foam, DuraFoam
Minimum 1.5" thick N/A N/A
Fesco Board
Minimum %" thick N/A N/A
1�I nim `W12?�,' t
M, Iwo N/A N/A
Top Insulation Layer Insulation Fasteners Fastener
(Table 3) Density/fe
Any listed insulation as Base Layer, above except ENRGY 3
Tapered Fesco Board
Minimum %11 thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt
within the EVT range and at a rate of 20-40 lbs./100 fe. Please refer to Roofing Application
Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used
only as base layers with a second layer of approved top layer insulation installed as the final
membrane substrate. Composite insulation panels may be used as a top layer placed with the
polyisocyanurate side facing down.
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 8 of 39
eet: ane - r more plies of GlasBase Plus, PermaPly No. 28, G1asPly Premier, G1asPly
IV, ^ yna as c T8 S DynaBase, DynaBase XT or DynaPly Tl adhered to the
base s icc wi approved mopping of asphalt applied within the EVT range and at
a rate of 20-40 lbs./sq. or one ply DynaWeld Base heat welded.
[Membrane One l.�,of DynaGlas FR CF, DynaKap TI, DynaKap FR Tl, DynaMax FR,
DynaGlas, DynaGlas FR, DynaGlas 30 FR, DynaGlas FR XT, DynaLastic 180,
DynaLastic 180 FF, DynaLastic 180 S, DynaLastic 250, DynaLastic 250FR or
DynaPly Tl adhered in a full mopping of approved asphalt applied within the EVT
range and at a rate of 2040 lbs./sq. or one ply DynaWeld Cap FR CR or
DynaWeld Cap FR heat welded.
Or
(Only with a modified Base or Ply sheet) as °ap or G1asKap CR Adhered in a
full mopping of approved asphalt applied within the EVT range and at a rate of 20-
40 lbs./sq.
Surfacing: (Optional) Install one of the following:
1. Flood coat and gravel/slag with an application rate of 60 lbs./sq. & 400
lbs./sq., respectively.
Maximum Design
Pressure: -82.5 psf.(See General Limitation #7)
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 9 of 39
LIGHTWEIGHT INSULATING CONCRETE SYSTEM LIMITATIONS:
1. If mechanical attachment to the structural deck through the lightweight insulating concrete is proposed, a field
withdrawal resistance testing shall be performed to determine equivalent or enhanced fastener patterns and density.
All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing
Application Standard RAS 117; calculations shall be signed and sealed by a Florida Registered Engineer, Architect,
or Registered Roof Consultant.
2. For steel deck application where specific deck construction is not referenced: The deck shall be a minimum 22
gage attached with 5/8" puddle welds with weld washers at every flute with maximum deck spans of 5 ft. o.c.
3. For systems where specific lightweight insulating concrete is not referenced, the minimum design mix shall be a
minimum of 300 psi.
GENERAL LEMTATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 IV., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. Insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida Registered Engineer, Architect, or Registered Roof Consultant may be
submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing
Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered-Architect,or_Registered: Roof .Consultant (When this limitation is_ specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 9N-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 13-0129.16
Expiration Date: 07/19/16
Approval Date: 06/27/13
Page 39 of 39