The URL can be used to link to this page

Home My WebLink AboutNOACOUNTY FILM�] SCHNNEL) BY St. Lucie Count% DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE (NOA) Johns Manville Corporation 717 17th Street Denver, CO 80202 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175-2474 T (786)315-2590 F (786) 31525-99 www.miamidade.-ov/economv SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Johns Manville Modified Bitumen Rooting Systems over Steel Deck. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews and revises NOA No. 13-0129.19 and consists of pages 1 throu h 70. The submitted documentation was reviewed b Jorge L. Acebo. Y g F61 .9, Cn3 61 w- MIAMI•DADE COUNTY NOA No.: 13-0529.18 Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 1 of 70 ROOFING SYSTEM APPROVAL Category Roofing Sub -Category: Modified Bitumen Materials: SBS Deck Tvpe• Steel Maximum Design Pressure: -195 psf. TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Dimensions Specification DynaBase 39-3/8" x 49'2" ASTM D 6163 Type I Grade S DynaBase PR 39-3/8" x 49'2" ASTM D6164 Type I Grade S DynaBase HW 39-3/8" x 49'2" ASTM D 6163, Type 1 Grade S -- DynaFast 180 S 39-3/8" x 49'2" ASTM D6164 DynaFast 180 HW 39-3/8" x 49'2" ASTM D6164 DynaFast 250 HW 39-3/8" x 32' 10" ASTM D6164 DynaWeld Base 39'-3/8" x 32'-10" ASTM D6163 Type I Grade S DynaWeld Cap 39'-3/8" x 32'-10" ASTM D6163 FR CR Type I Grade G DynaGlas FR CR 39-3/8" x 32'-10'; ASTM D6163 Type I Grade G DynaGlas 39-3/8" x 32'-10" ASTM D6163 Type I Grade G DynaWeld Cap FR 39'-3/8" x 32'-10" ASTM D6163 Type I Grade G DynaWeld Cap 39-3/8" x 32'-10" ASTM D6164 180 FR Type I Grade G DynaWeld Cap 39-3/8" x 32'-10" ASTM D6164 250 FR Type II Grade G MIAMI•DADE COUNTY 7us m Product Description A glass reinforced SBS modified bitumen base sheet. A polyester reinforced SBS modified bitumen base sheet. A glass reinforced SBS modified bitumen base sheet for heat welded applications. A polyester reinforced SBS modified bitumen base or inner ply sheet. A polyester reinforced SBS modified bitumen base or inner ply sheet for use in heat weld applications. A polyester reinforced SBS modified bitumen base or inner ply sheet for use in heat weld applications. A glass reinforced SBS modified bitumen base sheet for heat welded applications. A fire resistant, polyester reinforced SBS modified bitumen membrane surfaced with granules and a reflective white coating for use in heat weld applications. A fire resistant, glass reinforced SBS modified bitumen membrane surfaced with granules and a reflective white coating for use in heat weld applications. A glass reinforced SBS modified bitumen membrane surfaced with granules. A fire resistant, glass reinforced SBS modified bitumen membrane surfaced with granules for use in heat weld applications. A fire resistant, polyester reinforced SBS modified bitumen membrane surfaced with granules for use in heat weld applications. A fire resistant, polyester reinforced SBS modified bitumen membrane surfaced with granules for us ik heat weld applications. Ir NOA No.: ).18 t , Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 2 of 70 Test Product Product Dimensions Specification Description DynaWeld Cap 250 39-3/8" x 32'-10" ASTM D6164 A fire resistant, polyester reinforced SBS FR CR Type II Grade G modified bitumen membrane surfaced with granules and a reflective white coating for use in heat weld applications. DynaWeld Cap 250 39-3/8" x 32'-10" ASTM D6164 A polyester reinforced SBS modified Type II Grade G bitumen membrane surfaced with granules for use in heat weld applications. DynaWeld 250 S 39-3/8" x 32'-10" ASTM D6164 A polyester reinforced SBS modified Type II Grade S bitumen base or inner ply sheet for use in heat weld applications. DynaGlas 30 FR 39-3/8" x 32'-10" ASTM D6163 A fire resistant, glass reinforced SBS Type I Grade G modified bitumen membrane surfaced with granules. DynaGlas FR 39-3/8" x 32'-10" ASTM D6163 A fire resistant, glass reinforced SBS Type I Grade G modified bitumen membrane surfaced with granules. DynaKap T1 39-3/8" x 32'-10" ASTM D6162 A composite reinforced SBS modified Type I Grade G bitumen membrane surfaced with granules. DynaKap FR Tl 39-3/8" x 32'-10" ASTM D6162 A fire resistant, composite reinforced SBS Type I Grade G modified bitumen membrane surfaced with granules. DynaLastic 180 39-3/8" x 32'-10" ASTM D6164 A polyester reinforced SBS modified Type I Grade G bitumen membrane surfaced with granules. DynaLastic 180 FR 39-3/8" x 32'-10" ASTM D6164 A fire resistant, polyester reinforced SBS Type I Grade G modified bitumen membrane surfaced with granules. DynaLastic 180 S 39-3/8" x 32' 10" ASTM D6164 A polyester reinforced SBS modified Type I Grade S bitumen base or inner ply sheet. DynaWeld 180 S 39-3/8" x 32'-10" ASTM D6162 A polyester reinforced SBS modified Type I Grade S bitumen base or inner ply sheet for use in heat weld applications. DynaPly TI 39-3/8" x 32'-10" ASTM D6162 A composite reinforced SBS modified Type II Grade S bitumen base or inner ply sheet. DynaLastic 250 FR 39-3/8" x 32'-10" ASTM D6164 A fire resistant, polyester reinforced SBS Type II Grade G modified bitumen membrane surfaced with granules. DynaLastic 250 39-3/8" x 32'-10" ASTM D6164 A fire resistant, polyester reinforced SBS FR CR Type II Grade G modified bitumen membrane surfaced with granules and a reflective white coating. DynaLastic 250 S 39-3/8" x 32'-10" ASTM D 6164 A polyester reinforced SBS modified Type II Grade S bitumen base or inner ply sheet. DynaMax FR 39-3/8" x 32'-10" ASTM D6162 A fire resistant, composite reinforced SBS Type III Grade G modified bitumen membrane surfaced with granules. DynaMax S 39-3/8" x 32'-10" ASTM D6162 A composite reinforced SBS modified Type III Grade S bitumen base or it {7{��8 she j(■,��t� may NOA No.: 13-0529.18 MIAMI•DADE COUNTY Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 3 of 70 Test Product Product Dimensions Specification Description DynaClad 39-3/8" x 33' 10" ASTM D6298 A glass reinforced base sheet SBS modified bitumen membrane surfaced with foil. DynaBase XT 39-3/8" x 49'-2" ASTM D 6163 A glass reinforced SBS modified bitumen Type I Grade S base or inner ply sheet. DynaGlas FR XT 39-3/8" x 32'-10" ASTM D6163 A fire resistant, glass reinforced SBS Type I Grade S modified bitumen membrane surfaced with granules. GlasKap 36" x 36' ASTM D3909 A mineral surfaced, asphalt coated, fiberglass cap sheet. GlasKap CR 36" x 36' ASTM D3909 A white mineral surfaced, white acrylic coated, fiberglass cap sheet. Ventsulation Felt 36" x 36' ASTM D4897 Heavy duty fiber glass base sheet Type II impregnated and coated on both sides with asphalt with or without fine mineral stabilizer. Surfaced on the bottom side with coarse mineral granules embedded in asphaltic coating. GlasBase Plus 36" x 108' ASTM D4601 Type II asphalt impregnated and coated glass fiber base sheet for use in conventional and modified bitumen built- up roofing. G1asPly IV 36" x 180' ASTM D2178 Type IV asphalt impregnated glass felt for Type IV use in conventional and modified bitumen built-up roofing. GlasPly Premier 36" x 180' ASTM D2178 Type VI asphalt impregnated glass felt for Type VI use in conventional and modified bitumen built-up roofing. PermaPly 28 36" x 106' ASTM D4601 Type II asphalt impregnated and coated Type II glass fiber base sheet for use in conventional and modified bitumen built- up roofing. FesCant Plus Cant various ASTM C728 Factory pre -fabricated cant strips and taper Strips, and Taper edge, manufactured from expanded perlite Edge insulation. MBR Flashing N/A Proprietary A two component elastomeric, cold Cement Base and application adhesive, consisting of a Activator modified proprietary compound with an asphalt base. MBR Bonding N/A proprietary A two component urethane cold Adhesive application ad MBR Cold 5, 55, and 350 gal. ASTM D3019 One part, elas eliopl at � Application Type III adhesive i ��g,A Adhesive F y MBR Low VOC 5 gal Proprietary One part, asphalt modified urethane Membrane adhesive Adhesive NOA No.: 13-0529.18 MIAMI•DADE COUNTY Expiration Date: 07/19/16 • • •. 1 Approval Date: 10/22/15 Page 4 of 70 Test Product Product Dimensions Specification Description MBR RA 1.5L Cartridge Proprietary Two part, cold process membrane adhesive Membrane Adhesive JM Two Part N/A Proprietary A two-part urethane insulation adhesive Urethane Insulation Adhesive Bestile Industrial various ASTM D4586 A trowel grade, cutback bitumen flashing Roof Cement Type I grade cement mixture including inorganic fibers and mineral stabilizers. Flex -I -Drain various BOCA 76-61 Two piece flexible drain system composed SBCCI 89204 of a Noryl deck flange, a flexible neoprene UBC 3236 bellows and no hub connection. Available in various sizes and styles for most retro-fit applications. PC/PET RetroDrain various N/A Engineered resin copolymer fabricated drain for retrofit applications. USII RetroDrain various N/A One piece, aluminum fabricated drain for retrofit applications. Superpome various N/A Cast aluminum, heavy-duty drain for RetroDrain retrofit applications. FP-10 Vents 10" deck flange, base N/A One-way roof vent, designed for use in diameter of 4" and a various roof systems, for the release of height of 6" pressure created by gases or moisture vapor trapped within the roofing system. Expand-O-Guard various N/A Elastomeric expansionjoint cover for vertical expansion and seismic joints. Manufactured from non -reinforced, form - supported elastomeric bellows with a bifurcated waterproof attachment to metal flanges. Expand-O-Flash various N/A Expansion joint covers manufactured from non -reinforced, form -supported elastomeric bellows with a bifurcated waterproof attachment to metal flanges. Presto-Lok Fascia various TAS 114 A multi -piece fascia and flashing system and Flashing for built-up and modified bitumen roofing System systems manufactured from aluminum or steel. DynaTred & various N/A Preformed, skid -resistant boards. DynaTred Plus Roof Walkway NOA No.: 13-0529.18 MIAMI•DADE COUNTY Expiration Date: 07/19/16 • • - Approval Date: 10/22/15 Page 5 of 70 APPROVED INSULATIONS: TABLE 2 Manufacturer Product Name Product Description (With Current NOA) ENRGY 3, Polyisocyanurate Insulation. Johns Manville ENRGY 3 25 PSI, ValuTherm, ValuTherm 25 PSI, R-Panel, R-Panel25 PSI ENRGY 3 AGF, Polyisocyanurate Insulation with glass Johns Manville ENRGY 3 AGF 25 PSI, reinforced facers ENRGY 3 CGF, ENRGY 3 CGF 25 PSI, ValuTherm AGF, ValuTherm AGF 25 PSI, ValuTherm CGF, ValuTherm CGF 25 PSI ENRGY 3 FR Polyisocyanurate Insulation with inorganic Johns Manville coated glass reinforced facers; bottom face is premium coated for combustible decks. Fesco Foam, DuraFoam Polyisocyanurate Insulation with perlite Johns Manville facer Retro-Fit Board, DuraBoard High -density perlite roof insulation. Johns Manville Fesco Board Rigid perlite roof insulation board. Johns Manville Invinsa Roof Board High density polyisocyanurate board Johns Manville JM SECUROCK Gypsum -Fiber Rigid, gypsum -based board stock Johns Manville Roof Board DensDeck, DensDeck Prime Silicon treated gypsum Georgia Pacific Gypsum, LLC NOA No.: 13-0529.18 MIAMI-DADE COUNTY Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 6 of 70 APPROVED FASTENERS: Fastener Product Number Name 1. UltraFast Fastener ,/2 3 4. 5. 6. 7. 8. 9. 10. 11. TABLE 3 Product Description Insulation fastener for wood and steel. UltraFast ASAP Pre -assembled Insulation fastener and plate UltraFast 3" Round Galvalume AZ55 steel Metal Plate or UltraFast plate Square Recessed Metal Plate UltraFast Plastic Plate High Density Polyolefin round plate Dimensions #12x8" Max. Length, #3 Phillips head Various 3" round 3" square 3" round All Purpose Fastener Insulation fastener #14 x 16" Max. Length; #3 Phillips head High Load Fasteners Insulation and #15 x 14" membrane fastener for Max. Length steel, wood or concrete #3 Phillips head High Load Plate Steel Seam plate with 2-3/8" round reinforcing ribs and eyehooks High Load LH 415 Large Head #15 x 14" fastener for steel, wood, Max. Length or concrete Polymer Membrane Membrane anchors 1" x 250' coil Batten plastic strips APB Plates Steel Seam plate with 2" round reinforcing ribs and barbs Manufacturer (With Current NOA) Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Johns Manville Deep Well Batten Bar galvalume coated steel 1" x 100' coil Altenloh, Brink & Co. membrane batten U.S., Inc. NOA No.: 13-0529.18 Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 7 of 70 EVIDENCE SUBMITTED: Test Aeencv/Identifier Name Report Date Factory Mutual Research 3007148 FM 4450 04/19/00 3009499 FM 4470 04/04/01 3001482 FM 4470 08/11/98 3002823 FM 4470 04/01/99 3011248 FM 4470 11/01/02 3001457 FM 4470 04/04/02 3014090 FM 4470 09/05/02 3012974 FM 4450 06/03/02 3020600 FM 4470 01/21/05 3026130 FM 4470 04/26/06 3026151 FM 4470 08/15/06 3026728 FM 4470 11/22/06 3037222 FM 4470 10/02/09 3026130 FM 4470 04/26/09 3036559 FM 4470 10/02/09 3037540 FM 4470 10/20/10 3043824 FM 4470 06/28/06 Dynatech Engineering, 4360.03.95-1 TAS 114 03/95 4360.03.95-2 TAS 114 03/95 4361.5.95-1 TAS 114 05/95 Underwriters Laboratories, Inc. R10167 UL 790 05/27/13 Exterior Research & Design, LLC. 94361-2.04.97-1 TAS 114 04/28/97 10391.01.03 TAS 114 01/29/03 02843.02.05-10 TAS 114 02/10/05 00257.03.05-1 ASTM D6162/1)6163 03/17/05 ASTM D6164/D6298 TrinityjERD 02843.02.07 TAS 114 02/07/07 J7670.06.08 ASTM D3909 06/16/08 J6990.12.07 ASTM D6162/D6164 12/03/07 J17040.11.09 ASTM D6164 11/16/09 J13700.05.10-1-R1 ASTM D5147/D6163 01/25/11 J13700.05.10-2 ASTM D5147/D6164 05/11/10 J45020.07.13 FM 4474 (D)/TAS 114 (J) 07/12/13 Independent Roof Testing & IRT 99010 TAS 114 01/20/99 Consultants of South Florida IRT 99011 TAS 114 01/20/99 IRT-ARCON Inc. 02-026 TAS 114 07/26/02 02-011 TAS 114 02/06/02 Atlantic & Caribbean Roof ACRC 06-003 TAS 114 03/27/06 Consulting, LLC. y� PRI Construction Materials JMC-066-02-01 ASTM q61l 14Technologies, LLC JMC-065-02-01 ASTM 61 ii%ate IJMC-070-02-01 ASTM D2178 Type IV 7/i2 OM JMC-071-02-01 ASTM D2178 Type VI 04/17/12 JMC-072-02-01 ASTM D4601 Type II 06/14/12 NOA No.: 13-0529.18 MIAMI-DADE COUNTY Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 8 of 70 APPROVED ASSEMBLIES Membrane Type: SBS Deck Type 2I: Steel, Insulated Deck Description: Jl8-22 ga., min. 33 ksi steel deck placed over 0.25 in. thick structural steel supports spaced max. 6 fit o.c. attached with Buildex Traxx/5 fasteners spaced max. 6 in. o.c. at the supports. Side laps are secured with Buildex Traxx/1 fasteners spaced max. 30 in o.c. System Type B�1): Base layer of insulation mechanically fastened, top layer fully adhered with approved asphalt. All General and System limitations apply. Base Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ENRGY 3, ENRGY 3 25 PSI, ValuTherm, ValuTherm 25 PSI, R-Panel, R-Panel 25 PSI, Fesco Foam, DuraFoam / Minimum 2" ft thick 1 with 3, 5 with 3, or 2 1:1.45 ' V Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' Fesco Foam, DuraFoam Minimum 2" thick Retro-Fit Board, DuraBoard Minimum%11 thick � N/A_ F21 A .4on. �jP N/A N/A Note: Top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs./100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Base Sheet: (Optional if base sheet used) One ply of PermaPly 28, DynaBase, DynaBase XT, GlasBase, or GlasBase Plus adhered to the insulated substrate in aTull mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Ply Sheet: ( pt onal if ply sheet used) One or more plies of GlasPly Premier, G1asPly IV, DynaLastic 180 S, DynaFast 180 S, DynaLastic 250 S, DynaBase, DynaBase PR, DynaBase XT, DynaMax S or DynaPly TI adhered to the base sheet with approved mopping of asphalt applied within the EVT range and at a rate of20-40 lbs./sq. or one ply DynaWeld Base, DynaBase HW, DynaWeld 180 S, DynaFast 180 HW, DynaWeld 250 S or DynaFast 250 HW heat welded. NOA No.: 13-0529.18 Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 10 of 70 Membrane: One or more plies of DynaGlas FR CR, DynaKap Tl, DynaKap FR Tl, DynaMax FR, DynaGlas, DynaGlas FR, DynaGlas 30 FR, DynaGlas FR XT, DynaLastic 180, DynaLastic 180 FR, DynaLastic 180 S, DynaLastic 250 FR, DynaLastic 250 FR CR or DynaPly Tl adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or one ply DynaWeld Cap FR, DynaWeld Cap FR CR, DynaWeld Cap 180 FR, DynaWeld Cap 250, DynaWeld Cap 250 FR or DynaWeld Cap 250 FR CR heat welded. Or (Only with a modified Base or Ply sheet) GlasKap or GlasKap CR adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20- 40 lbs./sq. Surfacin (Optio ) Inst I one of the foll ing. 1. ood coat d gravel/slag/kith an 4pplication rate of 60 lbs./sq. & 400 GlasKap or GlaNCap-GR adhered in k&Aopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Maximum Design Pressure: -75 psf. (See general limitation #7). rol ' �40 � NOA No.: 13-0529.18 Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 11 of 70 STEEL DECK SYSTEM LIMITATIONS: 1. If mechanical attachment to the structural deck through the lightweight insulating concrete is proposed, a field withdrawal resistance testing shall be performed to determine equivalent or enhanced fastener patterns and density. All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing Application Standard RAS 117; calculations shall be signed and sealed by a Florida Registered Engineer, Architect, or Registered Roof Consultant. 2. For steel deck application where specific deck construction is not referenced: The deck shall be a minimum 22 gage attached with 5/8" puddle welds with weld washers at every flute with maximum deck spans of 5 ft. o.c. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 Ibf. Insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida Registered Engineer, Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. J 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS I I I and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with t) 1.jr�a tidif �a Rule 61 G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE a NOA No.: 13-0529.18 Expiration Date: 07/19/16 Approval Date: 10/22/15 Page 70 of 70 1 `17 Roof Insulations Fastener Placement Johns Manville 4' x 8' (1.22 m x Z44 m) Boards 12" s" t 4 Spaces @ 18" ++++ + + + + 15 Fasts. / Bd. 1 6" 6" + +�+ + t + + + + i + + Nt + i + l + +,+ + ►� 12" (.-- 16 Fasts. / Bd. 6" I � 1 + + + + + + 6„ 18 Fasts. / Bd. 6" 118" 118" 20 Fasts. / Bd. ++++++++ — 11A 1• ZZ fasts. / tsa. 24 Fasts. / Bd. 1 b"" Imo" Meets the requirements of ASTM C 728, Type 2 Features and Components Topl-oce Coating: Top surface is sealed with this special coating to reduce excessive asphalt absorption in hot -asphalt applied roofing systems. Expanded Perlite: Provides good dimensional stability, excellent insulation value with stable R-value and fire resistance. Reinforcing Cellulosic Fibers: Consists of recycled newsprint to provide strength to the board as well as high recycled content JM utilizes third parry certification by UL environment to certify the recycled content and contributes to the LEED Materials and Resource (MR) credit 4. Hot Asphalt Friendly: Utility board for use as a divorcing layer in re -roofing and in new construction as a top layer in multi -layer insulation systems proven to reduce the tendency for blistering in hot asphalt applications. '/2" HITHO-f IT�BOARO Perlite-Based Cover Board a Cellulosic Fibers • Selected Binders component CweraoaN Mule Ply Type PL Pedite LT fuvllrnnal System Compatibility This productmeyhe used as a componemm the systems. Please referenceproductappgcaban torspecific rnstailadon methodsendinrormaton. Compafible with the selected Multi-Plysystems above H Do not use with Single Ply systems Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted Energy and the Environment Installation/ApplicationME 39%ave average a C`-��LEED® Recycled Content 39%averagead Covers rer es visi[the ---,I M K'eetro-et pard product page ontl�eJM roofing ebsao. ENVIRONMENTAL 1-2 Retio-Fil Brain! ■117 HotAsphax Cold Applied Urethane Mechanically Adhesive Fastened Peak Advantage Guarantee Information Systems I Guarantee Term* When used in most2.5 ply BUR and SBS systems. 110,15 or 20 years Contact JM Technical Services for specific systems or terms over20 years. Codes and Approvals 4`P5a IF!" FM �7 C u�. US anA�a "PROVED RoauvtconvolPpprerM Refer to the Safety Data Sheet and product label prior to using this product The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at vwvw.jm.com(roofing. Refer to the Application Guides and Detail Drawings for instructions. Packaging and Dimensions Size 2'x4' (0.61mx1.22m) 4'x4' (1.22mx1.22in) 4'x8' 0.22 in x 2.44 IT) Thickness IT 0.27 cm) Board Weight(Ibs) 4.4 8.9 17.2 FtyPallet 1,536 1,536 3,072 Boards/Pallet 192 96 96 PalletWeight(lbs) 850 850 1,650 Pallets per Truck" 48 48 24 Producing Location Rockdale, IL Assumes 49' nathed truck. rp L, r-Upy RS-5047 10-I411eplaces a-14) Meets the requirements of ASTM C 1289, Type II, Class 1, Grade 2 (20 psi) • ENRGY 3 / Tapered ENRGY 3 Grade 3 (25 psi) • ENRGY 3 25 PSI /Tapered ENRGY 3 25 PSI Features and Components Glass -Reinforced Facers: Provides rigidity and resistance to indentation and crushing, and are compatible with BUR, modified bitumen and single ply membrane systems. Closed Cell Polyisocyanurate Foam Core: Provides high R-value per inch in built-up, modified bitumen, metal roof and single ply roof systems, and approved for direct application to steel decks. FEAT & TAPERED ENRGY 3® Polyisocyanurate Roof Insulation component Insultiw Mule -Ply single Pry Type HT Hyhihmml TP Tapered System Compatibility Thispmductmaybe usedas a componemin the rol/offing systems. Please reference product application for specific installation methods and information. Cumpa66fe with the selected Multi -Ply systems above us _ Compatible with all Single Ply systems _ Key: HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted Energy and the Environment LEEOm Recycled Content Varies with thickness, see Product Data and Packaging table on next page. Produced with a pentane blowing agentwith zero ozone depletion and virtually no global warming potential. Peak Advantage Guarantee Information Systems For use in approved JM Peak Advantage Roofing Guarantees Codes and Approvals G`pSSIFrFO C �� BS FM nt PI '. ZQ' `tyM k` •.Pmrveo nw.n��•wMvp..e • FM® Standards 4450/4470 Approvals (refer to FM RoofNav") • UL® Standard 790, 263 and 1256 (referto UL Roofing Materials system directory) • Meets the requirements of CAN/ULC S704, Type 2 & 3, Class 3 • California Code of Regulations, Tide 24, Insulation Quality Standard License #TI-1341 • Third -party certification with the PIMA Quality Mark" for Long -Term Thermal Resistance (LTrR) values Referto the Safe for Use instructions and product label priorto using this product The Safe for Use instructions am available by calling (800) 922-5922 or on the Web at www.im.cotn/roofing. Note: Technical information on this data sheet is intended to be used as a general guideline only and is subject to change without notice. Contact your JM Sales Representative for further details. InstaIlation,'.Applicatlon ftui� U VAN HotAsphalt Urethane Mechanicaly Loose Laid Adhesive Fastened Refer to the application instructions guidelines for proper utilization of this product Flute Span: Width of Rib Opening: Up to25/e" Up to33/e Up to4'/e" (6.67 cm) (8.57 cm) (11.11 cm) Insulation Thickness imin% 1.0"(254 cm) 12"(3.05 cm) 1.3(3.30 cm) Packaging and Dimensions Rat Sizes' %(1.22 4'x4' in x 1.22 m) 4'x8' 1 (1.22 In x 2 44 m) Tapered Size' 4' x 4' (1.22 in x 1.22 m) Producing Locations Bremen, IN Cornwall, ONT Fernley, NV Hazleton, PA Jacksonville, FL Stocking Locations' I Grand Prairie, TX Southgate, CA Tracy, CA 1. For available thicknesses, see PmductOam and Packagingtable on page 2 of this data sheet Other sizes available by special request some she am not stocked and special order With minimum order quantities. Contact your JM Sales Representative for details. 2 Tapered ENRGY 3 and Tapered ENRGY3 25 PSI are available in thicknesses of V2 to 4. Available profiles are shown on page 3 of this data sheet In some regions extended panels are also available. 3. Not all sizes, thicknesses, and products am stocked at all locations, please call Customer Service at 1877-765-3295. 21iffiAl"51"