Loading...
HomeMy WebLinkAboutNOASCANNEU MIMIDADE BY MIAMI-DADE COUNTY EM St. Lucie Count% PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION ) Miami, Florida 33175-2474 NOTICE OF ACCEPTANCE (NOA) T (786)315-2590 F (786) 315-2599 www.miamidnde �o / c om GAF 1 Campus Drive Parsippany, NJ 07054 SCOPE: This NOA is being issued under the applicable roles and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. (DESCRIPTION: GAF Conventional Built -Up -Roof Systems over Steel Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety, INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA No. 13-0424.13 consists of pages 1 through 22. The submitted documentation was reviewed by Jorge L. Acebo. MIAMtDADE COUNW NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Pagel of 22 ROOFING SYSTEM APPROVAL Category: Roofing Sub-CateZorV, BUR Material: Fiberglass Deck Type, Steel Maximum Design Pressure: -90 psf. TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE Product Dimensions Test Specification Product GATGLASO Ply 4 3937" ASTM D2178 Description Smooth surfaced asphaltic sheet (I meter) Wide ply reinforced with fiberglass mat. ® Tri-Ply Ply 4 39.37" (1 meter) Wide ASTM D2178 Smooth surfaced asphaltic ply sheet reinforced with GAFGLAS' FlexPly'" 6 39.37" ASTM D2178 fiberglass mat. Smooth surfaced asphaltic (I meter) Wide ply sheet reinforced with fiberglass mat. GAFGLAS'#75 Base Sheet 39.37" (I meter) Wide ASTM D4601 Smooth asphaltic base or base/ply sheet reinforced Tri-Ply' #75 Base Sheet 39.37" ASTM D4601 with fiberglass mat. Smooth asphaltic base or base/ply sheet (1 meter) Wide reinforced with fiberglass mat. GAFGLAS' #80 Ultima'" Base Sheet 39.37" (1 meter) Wide ASTM D4601 Smooth asphaltic base or base/ply sheet reinforced GAFGLAS' Stratavent' 39.37" with fiberglass mat. Perforated Venting Base (1 meter) Wide ASTM D4897 Smooth surfaced asphaltic perforated venting base Sheet sheet reinforced with fiberglass mat. GAFGLAS' Mineral Surfaced Ca Sheet P 39.37" (1 meter) Wide ASTM D3909 Granule surfaced asphaltic cap sheet reinforced with Tr -Ply' BUR— Cap Sheet 39.37" ASTM D3909 fiberglass mat. Granule surfaced asphaltic cap sheet (I meter) Wide reinforced with fiberglass mat. GAFGLAS' EnergyCap— Mineral Surfaced Cap 39.37" ' (1 meter) Wide ASTM D3909 Granule surfaced asphaltic cap sheet reinforced with Sheet fiberglass mat. Cap sheet is factory coated with Ruberoid' 20 Smooth TOPCOAT' EnergyCote'" Elastomeric Coating. 39.37" (1 meter) Wide ASTM D6163 SBS Polymer -modified asphalt base or ply sheet Ruberoid' Mop Smooth 39.37" reinforced with a fiberglass mat. (1 meter) Wide ASTM D6164 Smooth surfaced mop applied SBS base or ply sheet Ruberoid' Mop reinforced with a polyester mat. Smooth 1.5 39.37" (1 meter) Wide ASTM D6164 Smooth surfaced mop applied SBS base or ply sheet reinforced with a polyester mat C6DADacopR NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Paget of 22 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE Product Dimensions Test Specification Product Description Ruberoid® Mop Plus Smooth 39.37" ASTM D6164 Smooth surfaced mop applied SBS base or sheet Topcoat® Surface (I meter) Wide ply reinforced with a polyester mat. Seal SB 5 or 55 gallons ASTM D6083 Solvent -based thermoplastic rubber sealant designed to protect and restore aged roof surfaces and to Topcoat® Membrane 1, 5 or 55 gallons ASTM D6083 increase roof reflectivity. Water -based elastomeric coating. Topcoate MB Plus 5 or 55 gallons Proprietary P ry ` Water based, low VOC primer designed to block Topcoat® FlexSeal'" 1, 5 gallons or TAS 139 asphalt bleed -through. Solvent -based elastomeric sealant. 1 qt. tube APPROVED INSULATIONS: Product Name EnergyGuard'" Polyiso Insulation EnergyGuard'" RA Polyiso Insulation EnergyGuard'" RH Polyiso Insulation EnergyGuard'" RN Polyiso Insulation EnergyGuard'" RA Composite Polyiso Insulation EnergyGuard'" Perlite Roof Insulation EnergyGuard' Perlite Recover Board DensDeck® Roof Board DensDeck®Prime Roof Board Securocko Gypsum -Fiber Roof Board Stmctodek® High Density Fiberboard 11 MNNrDA®pNiY , TABLE 2 Product Description Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanumte foam insulation with high density fiberboard orpermalite Perlite insulation board Perlite recover board Gypsum board Gypsum board Gypsum board High density fiberboard Manufacturer (With Current NOA) GAF GAF GAF GAF GAF GAF GAF Georgia-Pacific Gypsum LLC. Georgia-Pacific Gypsum LLC. USG Corporation Blue Ridge FiberBoard, Inc. NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Page 3 of 22 APPROVED FASTENERS: TABLE 3 Fastener Product Product Number 1. Name Drill-Tec'" Description Dimensions Manufacturer (With Current NOA) #12 Fastener Phillips head, modified #12 x 8" max. GAF buttress thread, Pinch point, length, 43 carbon steel fastener for use Phillips head. in steel or wood decks. With CR-10 coating. Available with a pinch point or drill 2. Drill-Tec'" #14 Fastener point. Truss head, self -drilling, #14 x 16" Pinch point, high thread max. length,GAF fastener for use in steel, #3 Philli wood or concrete decks. head. 3. Drill-Tec'" AccuTrac®Flat A2-SS aluminized steel plate 3" square; Plate for use with Drill-Tec'" .017" thick GAF fasteners. 4. Drill-Tec' AccuTraox Recessed Plate Galvalume steel plate with 3" square; GAF recess for use with Drill- .017" thick Tec' fasteners. 5. Drill-Tec'" 3" Steel Plates Round Galvalume steel 3" Round stress plate with reinforcing GAF ribs and recessed for use with Drill-Tec'" fasteners. 6. Drill-Tec'" 3" Standard Steel Galvalume coated steel 3" Round Plates stress plate for use with GAF approved Drill-Tec'" fasteners. NUU,a-DA®UN1 NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Page 4 of 22 EVIDENCE SUBMITTED: Test Agency Test Identifier Description Factory Mutual Research Corp. Date 2B8A4 AM 4470 0108/98 3B9Q1.AM 4470 O/ O9 ODOA8.AM 4470 07/09/99 OY9Q5.AM 4470 04/O1/98 3011140 4470 08/14/01 3014547 3017250 4470 O/05/0 3035140 4470 4470 04//04 3023458 4470 08/10/09 3034312 4470 _ 07/18/06 3046388 4470 04/09/09 3036614 4470 09/24/12 Underwriters Laboratories, Inc. 06/09/06 IRT-ARCON, Inc. R1306 UL 790 07/22/13 TrinitylERD 04-009 TAS 114-J O1/26/04 G34140.04.11-2 ASTM D6163 04/25/I1 G31360.03.10 ASTM D6164 03/31/10 G34140.04.11-4 ASTM D4601 04/25/11 G34140.04.11-5 ASTM D4897 04/25/11 G34140.04.11-5-R1 ASTM D4897 10/18/13 G6850.08.07-1 ASTM D3909 08/13/07 G33470.01.11 ASTM D6164 11/16/11 C8500SC.11.07 ASTM D6862 11/30/07 G30250.02.10-3-RI ASTM D3909 11/26/12 G33470.01.11 ASTM D6164 01/13/11 G30250.02.10-3-R1 ASTM D3909 11/26/12 G30250.02.10-2 ASTM D6222 02/11/10 PRI Construction Materials GAF-314-02-01 Technologies LLC GAF-315-02-01 ASTM D2178 08/23/11 GAF-369-02-01 ASTM D2178 08/23/11 GAF-082-02-01 ASTM C1289 ASTM D6083 10/23/12 GAF-084-02-01 ASTM D6083 05/09/06 07/08/05 GAF-245-02-01 ASTM D6083 05/07/06 Momentum Technologies, Inc. AX04C9A ASTM D6162 061O5109 MwMMA®UNW NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Page 5 of 22 Membrane Type: BUR Deck Type 2I; Steel, Insulated Deck Description: 15-22 ga. steel System Type B(1): Base layer of insulation is mechanically attached to roof deck. Any subsequent layers are then adhered to base layer of insulation. Membrane is subsequently fully adhered All General and System limitations apply. to insulation. Base Insulation Layer Insulation Fasteners Fastener EnergyGuard" RA Polyiso Insulation EnergyGuard" (Table 3) Minimum 1.3" RH Polyiso Insulation Density/ft' thick 2,3,4,5,6 EnergyGuardd' RN Polyiso Insulation, EnergyGuard" RH Polyiso Insulation 1:4ft' Minimum 1.4' thick EnergyGuard' Polyiso Insulation, EnergyGuard' 2, 3, 4, 5, 6 RH Polyiso Insulation Minimum 1.4" 1:3 ft' thick 2, 3, 4, 5, 6 1:4 ft' EnergyGuard" RN Polyiso Insulation, EnergyGuard" RH Polyiso Insulation Minimum 1.5' thick Structodek® High Density Fiberboard 2,3,4,5,6 1:3 ft' Minimum 3/." thick EuergyGuard— Perlite Roof Insulation 2, 3, 4, 5, 6 1:4 ft' Minimum'/,' thick 2, 3, 4, 5, 6 1:2 ft - Note: Base layers of insulation shall be mechanically attached through the optional thermal barrier (when present) and into the steel deck; using the fastener density listed. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Rooting Application Standard RAS 117 for insulation attachment. GAF requires either a ply of GAFGLAS® Stratavent" Perforated Venting Base Sheet, loose laid dry or a layer of EnergyGuard— Perlite Roof Insulation or wood fiber overlay board on all polyisocyanurate applications. Top Insulation Layer Insulation Fasteners Fastener Any of the insulations listed above for Base Insulation Layer (Table 3) Density/ft, EnergyGuard'" Perlite Recover Board Minimum %." thick N/A N/A Note: The top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Minrm•Dn®UNTv NOA No.: 134022.18 Expiration Date: Il/U6/19 Approval Date: 04/02/15 Page 6 of 22 Base Sheet: (Optional) Install one or more plies of GAFGLASO Ply 4, Tri-Ply Ply 4, GAFGLASO F1exPly'" 6, GAFGLASO #75 Base Sheet, Tri-Ply® #75 Base Sheet, GAFGLASO 480 Ultima'"' Base Sheet, Rubercl 20 Smooth, Ruberoid® Mop Smooth, Ruberoid® Mop Smooth 1.5 or Ruberoid® Mop Plus Smooth directly to the insulated substrate. Adhere with any approved mopping asphalt applied within the EVT range and at a rate of 20A0 lbs./sq. Ply Sheet: Minimum two plies of GAFGLAS® Ply 4 or GAFGLASO FlexPly'M 6 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 2040 lbs./sq. Cap Sheet: One ply of GAFGLAS' Mineral Surfaced Cap Sheet, Tri-Ply BUR Granule Cap Sheet or GAFGLAS Ene�igyCap Mineral Surfaced Cap Sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq, in accordance manufacturer's instructions. with Surfacing: Optional on granular surfaced membranes; required for smooth membranes. Chosen components must be applied in accordance with manufacturer's instructions. All coatings must be listed within a current NOA. 1 Gravel or slag applied at 400 lbs./sq. and 300 lbs./sq, respectively in a flood coat of approved asphalt at 60 lbs./sq. 2. Topcoat® Membrane, Topcoat® MB Plus (to be used as a primer with Topcoat® Membrane) or Topcoat® Surface Seal SB applied at 1 to 1.5 3. gal./sq. Fibered Aluminum Roof Coating. Maximum Design Pressure: -45 ps£ (See General Limitation #9.) MIAMIDADE COUNTY NOA No.: 13-3022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Page 7 of 22 STEEL DECK SYSTEM LIMITATIONS: 1. If mechanical attachment to the structural deck through the lightweight insulating concrete is proposed, a field withdrawal resistance testing shall be performed to determine equivalent or enhanced fastener patterns and density, All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing Application Standard RAS 117, calculations shall be signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant. 2. For steel deck application where specific deck construction is not referenced: The deck shall be a minimum 22 gage attached with 5/81, puddle welds with weld washers at every flute with maximum deck spans of 5 ft. 0.c. GENERAL LIMTTATIONs: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery bond insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (FD value of 275 Ibf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 Ibf. insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and comers). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended comers and comers). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. END OF TMS ACCEPTANCE MIAMtDADECOUNry NOA No.: 13-1022.18 Expiration Date: 11/06/18 Approval Date: 04/02/15 Page 22 of 22 sa, TGFU.R1306 Roofing Systems GAF MATERIALS CORP I361 ALPS RD WAYNE, NJ 07470 USA RI306 ASPHALT FELT SYSTEMS WITH HOT ROOFING ASPHALT Class A ` 4. Deck: C-15/32 Incline: 1 Slip Sheet (Optional): —Red rosin paper, nailed to deck. Insulation (optional): — Any thickness nerlite or wood fiber or glass fiber or polyisocyanurate mechanically fastened or adhered with OMG Inc. "OlyBond Fastenizg System" or any UL Classified insulation adhesive. Base Sheet Qne pl .. ype`G2_"GAFG "' S©n9S-Base Sheet:' or "Tri-Piy® 7513ase Sheet" (may be nailed). Ply Sheet: — One or moreplies .Type G1> 1 GAFG _a c .ntv'a" or "Tri-Ply® Ply 4" or GAFGLAS© Ply 6". Cap Sheet One,:p. 1Type'G32 GA•F , T SO Mineral Surfaced'Can"Sheet" or "Tri- Ply® Mineral Surfaced Cap Sheet" or "GAFGLAS® EnergyCapTM BUR Mineral Surfaced Cap Sheet," Surfacing (optional): — "TOPCOAT® EnergyCoterw, applied at a rate of 2-gal/l00_ .2 Copyright © 2011 Underwriters Laboratories Inc. The appearance of a company's name or product in this database does not in itself assur,5 that products so identified have been manufactured under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow -Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: I, The Guide Information, Designs and/or Listings (files) must be presented in their entirety and in a non -misleading manner, without any manipulation of the data (or drawings). 2_ The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following format: "Copyright © 2011