The URL can be used to link to this page

Home My WebLink AboutCERTIFICATE OF CALIBRATIONCertincate -o f Calibration # KELC-430601 II�IIWI I�I�II�II) ��11�I� IIIIII��II III Kimball Electronic Laboratory, Inc. Precision Measurement Equipment Specialists Purchase Order# Calibration'Pertorined ey„ _ F_or QUE739 KIMBALL ELECTRONIC LABORATORY, INC QUEST ENGINEERING 8081 W 21 LANE 2737 NW 19TH STREET HIALEAH, FL. 33016 Egwpment Information KELI D r QUE=77666 .v POMPANO BEACH FL 33069 Description: DIGITAL SCALE Manufacturer. OHAUS Cal Date: 17-Feb-17 Model Number. E330R Cal. Due Date: 17-Feb-18 Part Number: ES30R Cal. Interval: 12 MONTHS Range: 0-30 KG SCANNED Received: IN TOLERANCE Calibration Result: PASS Serial Number: 30010805 BY Environmental Conditions: 75 DEG F / 45 % RH Customer I.D.: N/A St. Lucie County Performed By: RAUL Cust Barcode: NIA GONZALEZ Cust. Dept: N/A Procedure: SYN913 Specifications: ± 0.01 KG Cal Location: ON -SITE This Is to certify that the above listed instrument meals or exceeds all specifications as stated in the referenced procedure at the points tested (unless otherwise noted). It has been calibrated using measurement standards traceable to the Netionai Institute of Standards and Technology (NIST), or to NIST accepted intrinsic standards of measurement, or derived by the ratio type of self-cagbrdtion techniques. This calibration is in accerdance with i(imball Electronic Laboratory, Inc Quality Assurance Manual. KELI's Quality system is A21-A-Accredited to ISOIIEG170252005 and compliant with MILSTD-45662A and ANSONCSL Z540.5-2006. TURS when appricable are greater than or equal to 4:1; with expanded uncertainty used to calculate the Test Unmdainty Rego, with a coverage factor of K=2 at a confidence level of approximately 95%, unless otherwise noted. Any number of factors may cause the caribration item to drift out of calibration before the recommended interval has expired. CallbrattonRemarks.- - ,ry THIS UNIT WAS FOUND TO BE IN TOLERANCE AT THE TIME OF CALIBRATION. PERFORMED ROUTINE CAL. NO ADJUSTMENTS REQUIRED Standar`dsUsed�To"Calibrate Equfpment'�� ' �, t ' Company I.D. Manufacturer Mode1/PN Description Serial Number Last Cal. Cal. Due Date KIM001 7019 AMETEK T-150WEIGHTS 18830 02-Jun-16 30-Jun-17 Certified by: F �' Quality Assurance: RAUL JAVIER -' GONZALEZ 17—Feb-17 8:14:51 AM BALCEIRO 20—Feb-17 8:15:43 AM This report may not be reproduced, except in full, unless permission for the publication of an approved abstract is obtained in writing from KEU Labs., Inc. Kimball Electronic Laboratory, Inc. - 8081 W. 21 st Lane - Hialeah, FL. 33016 Tel: 305-8225792 - Toll Free: 800-393-1094 - Fax: 305-362-3125 - Web: www.kelilabs.com t Oate'_of Issue:';20 Feb 17 `. ` '.Page 1 of 2 z Cer�,>ijicate.of Calibration # KELC-430603 N�' Kimball Electronic Laboratory, Inc. t Precision Measurement Equipment Specialists Calibration Performed By - KIMBALL ELECTRONIC LABORATORY, INC 8081 W 21 LANE HIALEAH, FL. 33016 EqutpmenYtnformatton KELITsD QUE?77668' _`- Description: OVEN Manufacturer: QUINCY LAB. Model Number: 21-350 Part Number. 21-350 Range: 150-550 OF Purchase Order# For QUE739 QUEST ENGINEERING 2737 NW 19TH STREET POMPANO BEACH FL 33069 Cal Date: 17-Feb-17 Cal. Due Date: 17-Feb-18 Cal. Interval: 12 MONTHS Received: IN TOLERANCE Calibration Result: PASS Serial Number:. B23-3363 Environmental Conditions: 75 DEG F / 45 % RH Customer I.D.: N/A Performed By: RAUL Cust Barcode: N/A GONZALEZ Cust. Dept.: N/A Procedure: SYN1910 Specifications: MANUFACTURERS Cal Location: ON -SITE This is to certify that the above listed instrument meets or exceeds all specifications as stated in the referenced procedure at the points tested (unless otherwise noted). It has been calibrated using measurement standards traceable to the National Institute of Standards and Technology (NIST), or to NIST accepted intrinsic standards of measurement, or derived by the ratio type of self -calibration techniques. This calibration is in accordance with Kimbail Electronic Laboratory, Inc Quality Assurance Manual. KELI's Quality system is A&A-Accredited to ISOIIEC-17025:2005 and compliant with MILSTD45652A and ANSONOSL Z540.3-2006. TURS when applicable are greater than or equal to 4:1; with expanded uncertainty used to calculate the Test Uncertainty Ratio, with a coverage factor of K=2 at a confidence level of approximately 95%. unless otherwise noted. Any number of factors may cause the calibration item to ddft out of calibration before the recommended interval has expired. THIS UNIT WAS FOUND TO BE IN TOLERANCE AT THE TIME OF CALIBRATION. PERFORMED ROUTINE CAL. NO ADJUSTMENTS REQUIRED StandardsjUsed Ta Cal2brate Egwpment;r, .,_ ., `, Company I.D. Manufacturer MOdel/PN Description Serial Number Last Cal. Cal. Due Date KIM001 1061 OMEGA CL23A CALIBRATOR THERMOMETER T-279508 07-Apr-16 30-Apr-17 '- Certified by: Quality Assurance: RAUL JAVIER GONZALEZ 17—£eb-17 8:17:40 AM BALCEIRO 20—Feb-17 8:18:24 AM This report may not be reproduced, except in full, unless permission for the publication of an approved abstract is obtained in writing from KELI Labs., Inc. Kimball Electronic Laboratory, Inc. - 8081 W. 21st Lane - Hialeah, FL. 33016 Tel: 305-822-5792 - Toll Free: 800-393-1094 - Fax: 305-362-3125 - Web: www.kelilabs.com Date of issue ;20 Feb,17b, y, _ Page of 2'•