The URL can be used to link to this page

Home My WebLink AboutNOACoating SCANNED BY MI®� St. Luce County MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 31525-99 NOTICE OF ACCEPTANCE (NOA) www.miamldade.eov/economy LAPOLLA Industries, Inc. 15402 Vantage Parkway East, Suite 322 Houston, TX 77032 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RL'R reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Therm-O-Flex TF 1000 Series Elastomeric Roof Coating LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of (his entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No. 12-0726.04 and consists of pages 1 through 3. The submitted documentation was reviewed by Jorge L. Acebo. APPROVED NOA No.: 16-0525.09 Expiration Date: 08/09/21 Approval Date: 07/21/16 Page I of 3 ROOFING COMPONENT APPROVAL Cateeorv: Roofing Sub-Cateeorv: Cement -Adhesive -Coatings Materials: Elastomeric SCOPE: This approves "Therm-0-Flex TF 1000 Series Elastomeric Roof Coating" as a maintenance roof coating as manufactured by LAPOLLA Coatings, as described in this Notice of Acceptance, designed to comply with the Florida Building Code, High Velocity Hurricanes Zone. EVIDENCE SUBMITTED: Test Aeencv Test Identifier Test Name/Report Date Underwriter Laboratories, Inc. R14353 UL 790 12/15/11 Factory Mutual Research Corp. 3023796 Class 4470 10/02/05 PRI Construction Materials LP II- 013-02-01 ASTM D 6083 01/10/12 Technologies, LLC TT-C-555B MANUFACTURING LOCATION: 1. Houston, TX. PHYSICAL PROPERTIES OF COMPONENTS Trade names: Therm-O-Flex TF-1001(White), TF-1002(Grey), TF-1003(Tan) Thickness: Wet Film per Coat : 24 mils Dry Film per Coat: 13.2 mils Specifications: ASTM D 6083 Description: A water -based elastomeric coating membrane applied at an application rate of; • Galvanized Metal Roofs: Apply Base Coat at a rate of 1.5 to 2 gat/100 ftZ and Finish Coat at a rate of 1.5 to 2 gal/100 ftZ. • SBS Modified Bitumen Granule Surfaced Membranes: Apply Base Coat at a rate of 1.5 to 2 gal/100 ftZ and Finish Coat at a rate of 1.5 to 2 gal/100 ftZ. • EPDM Single Ply Membranes: Apply Base Coat at a rate of 1.5 to 2 gal/100 ftZ and Finish Coat at a rate of 1.5 to 2 gal/100 W. • Spray Polyurethane Foam Roof Systems: Apply Base Coat at a rate of 1.5 to 2 gal/100 ftZ and Finish Coat at a rate of 1.5 to 2 gal/100 ft. • Concrete Decks: Apply Base Coat at a rate of 1.5 to 2 gal/ 100 ftZ and Finish Coat at a rate of 1.5 to 2 gal/100 ft2. Container Size: 5, 55 and 275 gallons. Note all precautions on container. Systems Approvals: Methods of application and quantities shall comply with specific Roof Assembly, Product Control Notice of Acceptance. NOA No.: 16-0525.09 FOWDEO UNT`f Expiration Date: 08/09/21 "' • r Approval Date: 07/21/16 Page 2 of 3 BUILDING PERMIT REQUIREMENTS: Application for building permit shall be accompanied by copies of the following: This Notice of Acceptance 2. Any other documents required by the building official or the Applicable Building Code in order to properly evaluate the installation of this system. (_.IMITATIONS: 1, Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire rating of this product. 2. Therm-0-Flex TF 1000 Series Elastomcric Roof Coating shall not be applied in inclement weather conditions. 3. The products listed herein are components of roof assemblies and are approved for use with roof assemblies that list any of the products listed herein as part of their roof assemblies Notice of Acceptance. 4. All products listed herein shall have an unannounced follow-up quality control program from an approved listing agency. Follow up test results shall be made available to Miami -Dade Product Control upon request. 5. Change in materials, use, or manufacture of any of the products listed herein shall be cause for termination of this Notice of Acceptance. 6. Therm-0-Flex TF 1000 Series Elastomeric Roof Coating shall be used as a roof maintenance coating system in accordance with applicable Building Code. Therm-0-Flex TF 1000 Series Elastomercc Roof Coating is not approved for use as a recover system. 7. Therm-0-Flex TF 1000 Series Elastomcric Roof Coating shall be applied in accordance with manufacturer's published application instructions. 8. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. 9. All approved products listed herein shall be labeled in compliance with TAS 121 and shall bear the imprint or identifiable marking of the manufacturer's name or logo, city, stale and the following statement: "Miami -Dade Comity Product Control Approved" or the Miami -Dade County Product Control Seal as shown below MIAMMADEC UNTY END OF THIS ACCEPTANCE NOA No.: 16-0525.09 MUiM COl1tJTY Expiration Date: 08/09/21 Approval Date: 07/21/16 Page 3 of 3 S P I� MIAMF1 E - MIAMI-DADE COUNTY DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) PRODUCT CONTROL SECTION 11805 SW 26 Strect, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315.2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/economy LAPOLLA Industries, Inc. 15402 Vantage Parkway East Suite 322 Houston, TX 77032 SCOPE: SCANNED BY St. Lucie County This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AIIJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AIIJ may immediately revoke, modify, or suspend the use of such product or material within theirjurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Spray Polyurethane Foam — Foam Lok LPA 2500, 2800, 3000 over LWC Decks r LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been fried and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA# 10-0513.01 and consists of pages I through 6. The submitted documentation was reviewed by Alex Tigera. NOA No.: 15-0908.07 Expiration Date: 09/29/20 Approval Date: 10/15/15 Page I of 6 ROOFING COMPONENT APPROVAL Cateeorv: Roofing Sub-Cateeorv: Spray Applied Polyurethane Roof System Materials: Polyurethane Deck Type Wood Maximum Design Pressure -105 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: Product Dimensions Test Specifications Product Description Foam-LOK LPA 2500 2.5 lbs/ft' density TAS 110 Polyurethane spray applied foam that utilizes an HFC blowing agent intended for roofing applications. Foam-LOK LPA 2800 2.8 lbs/ft density TAS 110 Polyurethane spray applied foam that utilizes an HFC blowing agent intended for roofing applications. Foam-LOK LPA 3000 3.0 lbs1W density TAS 110 Polyurethane spray applied foam that utilizes an HFC blowing agent intended for roofing applications. Therm-0-Flex TF 1000 N/A ASTM D6083 A premium quality, fluid applied elastomeric Series Elastomeric Roof roof coating. Coating RCS-5000 Series N/A ASTM D6083 A premium quality, fluid applied elastomeric Restoration Coatings roof coating. Therm-0-Prime N/A A single component, water soluble acrylic emulsion primer to prepare Galvanized Metal, Concrete, Asphalt Substrates and Scarified Foam for new SPF installations. TRADE NAMES OF PRODUCTS MANUFACTURED BY OTHERS: Test Specifications Product Product Dimensions Description Manufacturer Any Miami -Dade N/A N/A As Required by Miami -Dade Roof coaling for County Approved County PCA application over Roof Coating polyurethane spray Perma Glas-Mesh Various N/A A reinforcing inorganic, woven applied foam. Saint-Gobain PGM 242 glass fiber fabric, coated with Technical Fabrics organic resin coating membrane. Securock .5"x 4'x 8' N/A Gypsum Board US Gypsum Olympic #15 XHD 3" round N/A Insulation fastener and stress OMG, Inc. Fastener and 3" Plate Various plate for steel and wood decks lengths Separator Sheet Various N/A Vapor Barrier to prevent Generic migration of moisture from LWC deck to insulation boards. MIAMMADECOUNTV NOA No.: 15-0908.07 • "' 0, I Expiration Date: 09/29/20 Approval Date: 10/15/15 Page 2 of 6 EVIDENCE SUBMITTED: Test Aaeney Test Identifier Test Name/Report Date PRI Construction Materials Technologies LPII-007-02-01 TAS 110 01/27/10 LPII-008-02-01 TAS 110 01/27/10 LPII-005-02-01 TAS 110 06/12/07 PRI Asphalt Technologies LPII- 002-02-01 ASTM D 6083/TAS 114-H 10/19/05 Underwriters Laboratories 07NK08120 UL 790 07/16/07 R14353 Fire Classification 06/26/05 Factory Mutual Research Corp. 3023796 Class 4470 LO/02/05 Atlantic & Caribbean Roof 09-016 TAS 114-J 10/19/09 Consulting, LLC I DECK STRESS ANALYSIS CALCULATIONS/REPORTS Enidncer/Aeencv Identifier Assemblies: Date Randall Fowler, P.E. Letter C 09/30/15 MUIMFD/1DECCIUNTY NOA No.: 15-0908.07 . • • • . � Expiration Date: 09l29/20 Approval Date: 10/15115 Page 3 of 6 APPROVED ASSEMBLIES: Deck Type 41: Lightweight Concrete, Insulated Deck Description: Conerecel Lightweight Concrete with min. compressive strength of 250-300 psi; '/; ' thick slurry is poured over the steel or concrete deck. Min 1" thick, 1.0 pef of Insulfoam EPS board is placed into the slurry, followed by a minimum 2" thick top coat of lightweight concrete. System Type Q: Sepemtor Sheet loose laid with insulation mechanically fastened through LWC to steel deck. SPUF applied over insulaion board. Deck: Minimum 22 ga. 50ksi, 1.5" type B G-90 Steel Deck with maximum 6' spans secured to the deck supports with Tek 5 SD screws 6" o.c. (every rib). Side laps secured with #10 self drilling screws at 12" o.c. This Tested Assembly has been analyzed for allowable deck stress. See Evidence Submittted Table. All General and System Limitations apply. One layer of the following insulation. Insulation Laver Insulation Fasteners Fastener Density/ft2 Securock Minimum .5" thick # 15 OMG XHD screw with 3" 1:2 Metal plates Separator Sheet: Required between the rigid insulation boards and the lightweight insulating concrete deck. Install one of the following products loose laid: 20 mil polyethylene sheet, red rosen paper or any ASTM D-226 Type II base sheet. Surface Any metal surfaces should be primed with Therm-0-Prime according to LAPOLLA Preparation: Industries, hrc. and coaling manufacturers' recommendations. Primer shall be thoroughly cured prior to application. For ferrous metal, remove loose rust and unsound primer from shop -primed iron and steel surfaces by scraping, wire brushing or sandblasting. Prime according to LAPOLLA Industries, Inc. and coating manufacturer's recommendations. For non-ferrous metals, clean and prime aluminum, copper and stainless steel surfaces as recommended by LAPOLLA Industries, Inc. Primers shall be applied in accordance with their manufacturer's instructions. All primers must be thoroughly dry and cured prior to foam application. Polyurethane Foam The polyurethane foam shall be applied uniformly over the entire surface of the insulation Application: at the specified thickness in compliance with the requirements set forth in Roofing Application Standard RAS 109, But in no case shall it be less than 111. The sprayed polyurethane foam shall be feathered at the edges to produce a smooth transition. NOA No.: 15-0908.07 MUIMFDAD; COUNTY Expiration Date: 09/29/20 Approval Date: 10/15/15 Page 4 of 6 Protective Coating Shall apply a Miami -Dade County approved roof coating with a current NOA applied in Application: accordance with the guidelines listed in the NOA. Polyurehane foam surface shall be free of moisture, dust, debris, oils, tars, grease or other materials that will as recommended by LAPOLLA Industries, Inc. impair adhesion of the protective coverings. Any damage or defects to the polyurethane foam surface shall be repaired prior to the coating application. The coating shall be applied the same day as the foam when possible. If more than 72 hours elapse prior to the application of the coatings, the polyurethane foam shall be inspected for UV degradation. Maximum Design Pressure: -105 psf, (See General Limitation #7.) MIAM4nU1DECWNTr NOA No.: 15-0908.07 UUMAJ Expiration Date: 09/29/20 Approval Date: 10/15/15 Page 5 of 6 TABLE I AMBIENT HUMIDITY APPLICATION LIMITS SPRAYED POLYURETHANE FOAM 110 LAPOLLA Industries, Inc. Air Temp/ Humidity/ Dew Point Guideline 100 90 80 70 60 so 40 30 45 67 40.5 50 70 45.5 55 72 50.5 60 75 55.5 * Airl 45 50 55 60 65 70 75 80 85 90 t Hui 67 70 72 75 76 80 78 75 70 64 ;4;83] * Deg 40.5 45.5 50.5 55.5 60.5 65.5 70 73.5 77 79.5 GENERAL LIMITATIONS: I. Fire classification is not part of this acceptance, refer to a current Approved Roofing Materials Directory for fire ratings of this product 2. Spray polyurethane foam shall not be sprayed when ambient temperature is within 5 degrees of the dew point- Ambient humidity applications limits shall be as listed in Table 1 herein. Contractor shall monitor and record environmental conditions in the Job Log in compliance with RAS 109. Job Log shall be maintained at the job site and accessible to The Building Official. 3. Flashings and waterproof coverings for expansion joints shall be of compatible materials and in accordance with LAPOLLA Industries, Inc. published literature. 4. Miscellaneous materials such as adhesives, elastomel is caulking compounds, metal, vents and drains shall be a composite part of the roof system and shall be compatible with the foam and coating. 5. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 6. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 Ibf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 ]bf. Insulation attachment shall not be acceptable. 7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform with Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and comers). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended comers and comers). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) END OF THIS ACCEPTANCE NOA No.: 15-0908.07 Expiration Date: 09/29/20 Approval Date: 10/15/15 Page 6 of 6