HomeMy WebLinkAboutSUBMITTED PAPERSDATE:
FEES DUE:
RECEIPT
Permit
Planning & Development Services Department
Building & Code Regulation Division
2300 Virginia Avenue
Ft. Pierce, FL 34982-5652
Tel. 772-462-1553
APPLICATION FOR ROOF PERMIT
SEE REVERSE SIDE FOR INSTRUCTIONS
1. Location/Site Address: 866 Nettles By
2. Parcel ID Number: 4502-501-1052-000-7
sc
St. �
UCie county
Office Use
Section
Township
Range
Map Page
I Zoni
La d Use
Ini
Only
3. Description of Project or Work Activity: Re -roof 12 squares of asphalt shingles QTt5-uZ-i EE= )
4. Total Roof Area (square feet): `aCL 5. Roof Pitch: 3/12
6. Type of Roof: [ ] Fiberglass Shingle [ ] Concrete Roof Tile [X] Wood Shake / Shingle
[ ] Tar & Gravel [ ] Modified Bitumen [ ] Other
[ ] Product Approval required for all types of Roofing Material (2 Sets)
[ ] All Commercial Roofing requires design by an Engineer or Architect (2 Sets) with Product
Approval attached
** Roof Mitigation per F.S. 553.844 will be required.
7. Owner Informatiion 8. Contractor Informatiion
Name: Renaud and Monique Paris FL Reg/Cert #: CCC058327
Address: 866 Nettles By County Cert #:
City: Jensen Beach State: FL
Zip: 34957 Phone: (772) 229 - 8967
9. Value of Construction: $ 5464.00
Business Name: The Home Depot At Home Services
Cell Phone:
"Note Dry -in and Final Inspection Required. Additional inspection may be required per Product Approval.
CONTRACTOR/OWNER'S AFFIDAVIT: I certify that all e infotmation contained in this aprtiektion is correct and that all work will be
done in compli nce with ail applicable !K�a g ons ruction and zoning.
Quinn Roberts
PRINT QUALIFIERS/OWNERS NAME SIGNATURE
// U FI
STATE OF FLORIDA, COUNTY OF IR. l�
ACKNOWLEDGED BEFORE ME THIS 13 DAY OF 201 , BY Quinn Roberts _
WHO IS PE S Y TO ME OR HAS PRODUCED AS IDENTIFICATION
it,,�(� _ D AMBER FLENKER
iii U(�� F-Len �r S" NOTARY PUBLIC
SIGNA NOTAR TYPE OR PRINT NAME OF NOTARY (seal) g� STATE OF FLORIDA
a]-rj(�R� Comm#EE215692
COMMISSION NUMBER Expires 7/11/2016
NOTICE TO OWNER: FAILURE TO RECORD A NOTICE OF COMMENCEMENT MAY RESULT IN YOUR PAYING TWICE
FOR IMPROVEMENTS TO YOUR PROPERTY. IF YOU INTEND TO OBTAIN FINANCING, CONSULT YOUR LENDER OR
ATTORNEY BEFORE RECORDING YOUR NOTICE OF COMMENCEMENT.
Revised 4/26/2010
Planning & Development Services
Building & Code Regulation Division
2300 Virginia Avenue
Fort Pierce, FL 34982
772-462-2165 or 772-462-2172
Fax: 772-462-6443
ROOF INSPECTION AFFIDAVIT
Re: Permit #
I� Quinn Roberts licensed as a( Contractor Engineer/Architect
(Please print name & circle license type) *FS468 ui ing Inspector
*General, Building, Residential or Roofing Contractor or any individual certified under 468 F.S. to make such an inspection.
On or about , I did personally inspect the roof deck naili
(Date)
work at: 866 Nettles Av. Jensen Beach, FL 34957
(Job site address)
Based upon that examination I have determined the installation was done according to the Hurricane
Mitigation Retrofit Manual (Based on 553.844 F.S.)
CCC058327
License #
STATE OF FLORIDA
DA
COUNTY OF !�ke-
Sworn to and subscriibnbed-- befor � me this day of 20
by (,tt`/I^ I-4D-. Who is personally known to me or who has produced
as identificat' n.
Notary Public, State of Flo
Signature of Notary:
Commission Number: V (Seal)
En 01/19/2011
AMBER FLENKER
NOTARY PUBLIC
s -STATE OF FLORIDA
'W-7.Comm# EB295692
Expires7/11/2016
JOSEPH E. SMITH, CLERK OF THE CIRCUIT COURT — SAINT LUCIE COUNTY
FILE # 3927047 OR BC, ,�1605 PAGE 2332, Recorded 02/20/2014,' ,01:29 PM
AFI'Elt RECORDING - RETURN TO:
PERMIT NUMBER: _-, 7 3 -3/ ci2
NOTICE OF COMMENCEMENT
The undersigned hereby gives notice that improvement will be made to certain real property, and in accordance with Chapter 713,
Florida Statutes, the following information is provided in this Notice of Commencement.
I. DESCRIPTION O`FPROPERTY (Legal description of the property & street address, if available) TAX FOLIO NO.: NSo1.-Sot-to52_Goo-�(
SUBDIVISION I1��5.LN �$�dnd, ni-�1 fT 0 BLOCK TRACT LOT SLDG UNIT'
&&i AJeA�41,, Wyfit. jen5e r. &a&. 51. _3 W16-7
2. GENERAL llESCRIPf10N OF IF
rC'('oo�
J. OWNER INFORMATION OR LESSEE INFORMATION IF THE LESSEE CONTRACTED FOR THE IMPROVEMENT: a. Name and address: Z "dtLA RQ-J'}-��(O�' Ne-�fIYSV� 3�5e,. 5, 3 �/ �/
b. Intetestun property' —
c Name and address of fee simple titleholder (if different from Owner listed above):
4. a. CONTRACTOR'S NAME: I I• -0 6r^e—
Cnnhacior's address: i%4 ee(lPt
i. SURETV lit applicable. a copy critic payment bund its anuchedl.
x Namc mat address
b. Phone number
C. Amount of bond:
b. Phone number f-q c3, - - L,[.
6. it. LENDER'S NAME:
Lender's address b. Phone number
7. Persons within the State of Florida designated by Owner upon whom notices or other documents may be served as provided by
Section 713.13 (1) (a) 7., Florida Statutes:
a Name and address
b I'homse numbers of designated persons:
8. a. In addition to himself, or.herself, Owner designates °f
to receive a copy ofthe Lienor's Notice as provided in Section 713.13 (1) (b), Florida Statutes.
b. 1'I1onc number of person or entity designated by Owner.
9. Expiration date of notice of commencement (the expiration date may not be before the completion of construction and final
payment to the contractor, but will be I year from the date of recording unless a different date is specified): 20
Under pen f perjury, I declare at I have read the foregoing notice of commencement and that the facts stated therein are true to
the bes nowledge d b ' n
v� �2/1 akd Yar►s
(Signature of Owner or Lessee, or Owner's or Lessee's (Print Name and Provide Signatory's Title/Office)
Authorized Officer/Director/Partner/Manager)
State of_V2�/v N
I' County of '/" ,
)'tic furegoing instrument was acknowledged before me this day of r. / 20
�trtn as t—
�a by (type of authority,...e.g. officer, trustee, attorney in fact)
�r Tr OF � �-C�� QA for ���eofperson)
�: L UCp E- 0004TY (name of party on behalf of whom instrument was executed)
TNI810ToGINTIFYT�.',�'�"'1413+18)' 1lyKnown or Produced ldeutiflcation ZTypeofldentificalionProduced'4 �`o�r�ktL'�r�trP.✓Y4-1_eF/�Sf
TR Ut AP41
�D f'OPY H
!� I I i OF THE
STEPHEN C. BLEHL
p-�i,. i MY COMMtSs10N/l20lll6fi (gig atureofNotaryPublle)
� N P' ..r.a,. -' j�. 6i EnYtRFB:rtwe24,101{ (Print, Type, or Stamp Commissioned Name of Notary Public)
Date
Appt:
Job # 7336992
Sales Contact:
Paris
866 Nettles Blvd
Length Diagram
Field Inspector:
7 7
Jensen Beach, FL 34957-3368
N
S
Note: This diagram contains segment lengths (rounded to the nearest whole numbers) over 5 feet. In
some cases, segment labels have been removed for readability. Plus signs preface some numbers to
avoid confusion when rotated (e.g. +6 and +9)
ROOFING SPECIFICATION SHEET
DESCRIPTION OF WORK
(Cqp)? orPSG)
Customer Name: Renuaud &monique Paris
Branch Name: Miami
Sales Consultant: Stephen Blehl
Hurricane Mitigation = No
APS
Timberline Ultra HD Lifetime
Barkwood
Number of Squares (excluding Low Slope) = 11.5
Number of Flat Roof Squares = 0
Misc
Rigid Ridge Vent = Yes
Linear Ft Ridge Vent to be Installed = 40
Rigid Ridge Vent - Color = Black
Off Ridge Vent = No
Replace Fascia = No
Hurricane Mitigation Inspection = No
Section 1
S1 Type = Gable
S1 Length - Linear Feet =12
S1 Width - Linear Feet = 6
S1 Pitch = 3/12
S1 Number of Valleys = 0
S1 - Removal - Number of Layers = 1
S1 - Removal Type - Layer 1 = Asphalt
S1 Additional Stories = No
Section 3
S3 Type = Hip
S3 Length - Linear Feet = 10
S3 Width - Linear Feet = 2
Date: 2/5/2014
Job #:
Material Removal:
See Sections for Material Removal
Roof Material = Composition Shingles
Number of Sections = 3
Flashing
Linear Ft of Drip Edge to be Installed = 147
Color of Drip Edge to be Installed = White
Section 2
S2 Type = Gable
S2 Length - Linear Feet = 38
S2 Width - Linear Feet = 25
S2 Pitch = 3/12
S2 Number of Valleys = 0
S2 - Removal - Number of Layers = 1
S2 - Removal Type - Layer 1 = Asphalt
S2 Additional Stories = No
Consultant: Stephen Bfeht Page 1 of 4 Job A:
Florida Building Code Online- - ` -� Page 1,of 2
riwildia Clkpartme d
BCIS Home I Log In ( user Registration Hot Topics j Submit Surcharge ( Stats & Facts I Publications FBC Staff ! BCIS Site Map Links Search
3usines
Professi nal
=,
}
� Product Approval
;' „' , USER: Public User
Regulation
ENO
Product Approval Menu > Product or Application Search > Application List > Application Detail
®
FL #
FL10124-R10
Application Type
Revision
Code Version
2010
Application Status
Approved
Comments
Archived
( 1
Product Manufacturer GAF
Address/Phone/Email 1361 Alps Road
Wayne, NJ 07470
(973) 872-4421
Iindareith@trinityerd.com
Authorized Signature
Beth McSorley
Iindareith@trinityerd.com
Technical Representative
Beth McSorley
Address/Phone/Email
1361 Alps Road - Bldg 11-1
Wayne, NJ 07470
(973) 872-4421
BMcSorley@gaf.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Asphalt Shingles
Compliance Method Evaluation Report from a Florida Registered Architect or a Licensed
Florida Professional Engineer
[6 Evaluation Report - Hardcopy Received
Florida Engineer or Architect Name who
developed the Evaluation Report
Florida License
Quality Assurance Entity
Quality Assurance Contract Expiration Date
Validated By
Certificate of Independence
Referenced Standard and Year (of Standard)
Equivalence of Product Standards
Robert Nieminen
PE-59166
UL LLC
05/03/2014
John W. Knezevich, PE
L Validation Checklist - Hardcopy Received
FL10124 R10 COI Trinity ERD CI - Nieminen - 2013.odf
Standard Year
ASTM D3161 (Class F) 2006
ASTM D3462 2007
ASTM D7158 (Class H) 2007
TAS 107 1995
http://floridabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDquracBeVCbdMQNZ... 8/23/2013
Florida Building Code Online
Page 2 of 2
Certified By
Sections from the Code
Product Approval Method
Date Submitted
Date Validated
Date Pending FBC Approval
Date Approved
Method i Option D
06/21/2013
06/24/2013
07/01/2013
08/23/2013
......... ..... _................................... --................................. _............... _.... _... ................... _._......... ------..................... .... ,..... _.._...... _............................... _...... __._..... _.......................
Summary of Products
Model, Number or Name
Description
L10124.1
GAF Asphalt Roof Shingles
Fiberglass reinforced 3-tab, laminated, 5-tab and
hip/ridge asphalt shingles
Limits of Use
Installation Instructions
Approved for use in HVHZ: No
FL10124 R10 II er062113FINAL GAF Asphalt
Shingles FL10124-R10.pdf
Approved for use outside HVHZ: Yes
Impact Resistant: N/A
Verified By: Robert Nieminen PE-59166
Design Pressure: N/A
Created by Independent Third Party: Yes
Other: Refer to ER, Section 5.
Evaluation Reports
FL10124 R10 AE er062113FINAL GAF Asphalt
Shingles FL10124-R10.pdf
Created by Independent Third Party: Yes
Back Next
Contact Us :: 1940 North Monroe Street. Tallahassee Fl, 32399 Phone: 850-487-1824
The State of Florida is an AA/EEO employer. Coovriaht 2007-2010 State of Florida.:: Privacy Statement :: Accessibility Statement :: Refund Statement
Under Florida law, emall addresses are public records. If you do not want your e-mail address released in response to a public -records request, do not
send electronic mail to this entity. Instead, contact the office by phone or by traditional mail. If you have any questions, please contact 850.487.1395.
*Pursuant to Section 455.275(1), Florida Statutes, effective October 1, 2012, licensees licensed under Chapter 455, F.S. must provide the Department
with an email address if they have one. The emails provided may be used for official communication with the licensee. However email addresses are public
record. If you do not wish to supply a personal address, please provide the Department with an email address which can be made available to the public.
To determine if you are a licensee under Chapter 455, F.S., please click here .
Product Approval Accepts:
L eG�eik M
fiEr.`.til'{tYb6 f'rlt It„4'
http://floridabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDquracBeVCbdMQNZ... 8/23/2013
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
oTmNRY
ERD 353 CHRISTIA OXFORD, CT UNIT
06478
PHONE. (203) 262-9245
FAX: (203) 262-9243
EVALUATION REPORT
GAF Evaluation Report 01506.01.08-R12
1361 Alps Road, Building 7-3 FL10124-R10
Wayne, NJ 07470 Date of Issuance: 01 /03/2008
Revision 12: 06/21 /2013
SCOPE:
This Evaluation Report is issued under Rule 9N-3 and the applicable rules and regulations governing
the use of construction materials in the State of Florida. The documentation submitted has been
reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and
Florida Building Code, Residential Volume. The products described herein have been designed to
comply with the 2010 Florida Building Code sections noted herein.
DESCRIPTION: GAF Asphalt Roof Shingles
LABELING: Each unit shall bear labeling in accordance with the requirements the Accredited Quality
Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s)
changes, the referenced Quality Assurance documentation changes, or provisions of the Code that
relate to the product change. Acceptance of this Evaluation Report by the named client constitutes
agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality
Assurance documentation changes. TrinityjERD requires a complete review of this Evaluation
Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may
be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it
shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by
the manufacturer or its distributors and shall be available for inspection at the job site at the
request of the Building Official.
This Evaluation Report consists of pages 1 through 4.
r
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized
by Robert Nieminen, P.E. on 06/21/2013
This does not serve as an electronically signed
document. Signed, sealed hardcopies have been
transmitted to the Product Approval Administrator and
to the named client
CERTI F [CATION OF INDEPENDENCE:
1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. TrinitylERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which
the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
\.t TRINIT(IERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Asphalt Shingles
Compliance Statement: GAF Asphalt Roof Shingles, as produced by GAF, have demonstrated
compliance with the following sections of the Florida Building Code and Florida Building Code,
Residential Volume through testing in accordance with the following Standards. Compliance is subject
to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section
Property
Standard
Year
1507.2.5, R905.2.4
Physical Properties
ASTM D3462
2007
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D3161, Class F
2006
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D7158, Class H
2O07
1507.2.7.1, R905.2.6.1
Wind Resistance
TAS 107
1995
3. REFERENCES:
Entity
Examination
Reference
Date
GAF (PDM 1915)
Letter of Equivalency
Seal -A -Ridge Impact Resistant IR
01/13/2012
PRI(TST 5878)
ASTM D3462
GAF-059-02-01
09/02/2004
PRI(TST 5878)
ASTM D3462
GAF-080-02-01
05/25/2005
PRI (TST 5878)
Wind Driven Rain
GAF-407-02-01
01/21/2013
UL(TST 1740)
ASTM D3462
93NK6295
11/29/1993
UL(TST 1740)
ASTM D3462
99NK43835
01/12/2000
UL(TST 1740)
TAS 107
94NK9632
03/29/2000
UL(TST 1740)
ASTM D3462
01NK06632
02/02/2001
UL(TST 1740)
ASTM D3161, TAS 107
01NK9226
05/21/2001
UL(TST 1740)
ASTM D3161
OINK37122
12/18/2001
UL(TST 1740)
ASTM D3462
01NK37122
12/19/2001
UL(TST 1740)
ASTM D3161, TAS 107
02NK12980
04/10/2002
UL(TST 1740)
ASTM D3161, TAS 107
02NK30871
09/09/2002
UL(TST 1740)
ASTM D3161
03CA5367
03/11/2003
UL(TST 1740)
ASTM D3462
03NK26444
10/17/2003
UL(TST 1740)
ASTM D3462
04NK13850
06/07/2004
UL(TST 1740)
ASTM D3161
04NK13850
06/23/2004
UL(TST 1740)
ASTM D3161
04NK30546
03/10/2005
UL(TST 1740)
ASTM D3462
04NK22009
05/06/2005
UL(TST 1740)
ASTM D3161
04NK22009
05/09/2005
UL(TST 1740)
ASTM D3462
05NK27924
02/10/2006
UL(TST 1740)
ASTM D3161
05NK27924
02/11/2006
UL(TST 1740)
ASTM D3161, D3462
06CA18077
06/05/2006
UL(TST 1740)
ASTM D3161, D3462
06CAlBO74
06/16/2006
UL(TST 1740)
ASTM D3161, D3462
06CA35251
10/18/2006
UL(TST 1740)
ASTM D3462
06CA31603
12/01/2006
UL(TST 1740)
ASTM 'D3161,D3462
06CA41095
12/27/2006
UL(TST 1740)
ASTM D3161
07NK05228
03/13/2007
UL(TST 1740)
ASTM D3161
06CA31611
04/04/2007
UL(TST 1740)
ASTM D3161
06CA61148
04/09/2007
UL(TST 1740)
ASTM D3161, D3462
07CA31742
11/08/2007
UL (TST 1740)
ASTM D3161, D7158, D3462
OBCA06100
03/13/2008
UL(TST 1740)
ASTM D3161, D3462
07CA55908
04/01/2008
UL(TST 1740)
ASTM D3161, D3462
09CA10592
03/26/2009
UL(TST 1740)
ASTM D3161, D3462
09CA06856
05/15/2009
UL (TST 1740)
ASTM D3161, D7158, D3462
09NK06647
08/01/2009
UL (TST 1740)
ASTM D3161, D7158, D3462
09CA27281
08/27/2009
UL (TST 1740)
ASTM D3161, D7158, D3462
10CA35554
03/05/2010
UL (TST 1740)
ASTM D3161, D7158, D3462
10CA13686
05/15/2010
UL(TST 1740)
ASTM D3462
10CA07264
05/27/2010
UL (TST 1740)
ASTM D3462
10CA11953
10/29/2010
UL(TST 1740)
ASTM D3161, D7158, D3462
1ONK11951
10/30/2010
UL(TST 1740)
ASTM D3161, D7158, D3462
1ONK12070
11/04/2010
UL(TST 1740)
ASTM D3161, D7158, D3462
OBCA06100
01/30/2010
UL(TST 1740)
ASTM D3161, D7158, D3462
10CA53934
03/31/2011
UL(TST 1740)
ASTM D3161, D7158, D3462
11CA48924
10/22/2011
UL(TST 1740)
ASTM D3161, D7158, D3462
11CA47919
12/03/2011
UL (TST 1740)
ASTM D3161, D7158, D3462
'11CA48408
12/08/2011
Exterior Research and Design, LLC. Evaluation Report 01506.01.08-R12
Certificate of Authorization #9503 FL10124-R10
Revision 12: 06/21 /2013
Page 2 of 4
Entity
UL (TST 1740)
UL, LLC. (TST 9628)
UL, LLC. (TST 9628)
UL, LLC. (TST 9628)
UL, LLC. (QUA 9625)
4. PRODUCT DESCRIPTION:
Examination
ASTM D3161, D7158, D3462
ASTM D3462
ASTM D3161, D7158, D3462
ASTM D3161
Quality Control _
Reference
Date
11CA48725
12/09/2011
12CA34891
10/12/2012
12CA58151
02/15/2013
13CA32332
06/18/2013
Inspection Report, File No. R21
05/03/2013
4.1 Marquis WeatherMax, Royal Sovereign and Sentinel are a fiberglass reinforced, 3-tab asphalt
roof shingles.
4.2 Camelot, Camelot II, Capstone, Country Mansion, Country Mansion II, Grand Canyon, Grand
Sequoia, Grand Sequoia IR, Grand Slate, Grand Slate II, Monaco, Sienna, Timberline American
Harvest, Timberline ArmorShield II, Timberline Natural Shadow, Timberline Natural Shadow
Arctic White, Timberline HD, Timberline Cool Series, Timberline Ultra HD and Woodland are
fiberglass reinforced, laminated asphalt roof shingles.
4.3 Slateline is a fiberglass reinforced, 5-tab asphalt roof shingle.
4.4 Seal -A -Ridge, Seal -A -Ridge Armorshield, Seal -A -Ridge IR and Timbertex Hip and Ridge are
fiberglass reinforced, hip and ridge asphalt roof shingles.
4.5 Pro -Start Starter Strip Shingles and WeatherBlocker Starter Strip Shingles are a starter strips
for asphalt roof shingles.
5. LIMITATIONS:
5.1 This Evaluation Report is not for use in the HVHZ.
5.2 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing
Materials Directory for fire ratings of this product.
5.3 Wind Classification:
5.3.1 All GAF shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are
acceptable for us in all wind zones up to Vaed = 150 mph (V„ It = 194 mph). Refer to Section 6
for installation requirements to meet this wind rating.
5.3.2 All GAF hip & ridge shingles noted herein are Classified in accordance with FBC Tables
1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the shingles are acceptable for
us in all wind zones up to Vaed = 150 mph (V„it = 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.3.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60
feet or less. Calculations by a qualified design professional are required for conditions outside
these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4 All products in the roof assembly shall have quality assurance audit in accordance with the
Florida Building Code and F.A.C. Rule 9N-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to GAF and shall hold current Florida Statewide Product
Approval, or be Locally Approved per Rule 9N-3, per FBC Sections 1507.2.3, 1507.2.4 or
R905.2.3.
Exterior Research and Design, LLC. Evaluation Report 01506.01.08-R12
Certificate of Authorization #9503 , FL10124-R10
Revision 12: 06/21 /2013
Page 3 of 4
TRINITY ERD
6.2 Starter Shingles:
6.2.1 Installation of Pro -Start Starter Strip Shingles and WeatherBlocker Starter Strip Shingles shall
comply with the manufacturer's current published instructions.
6.3 Asphalt Shingles:
6.3.1 Installation of asphalt shingles shall comply with the manufacturer's current published
instructions, using minimum four (4) nails per shingle in accordance with FBC Sections 1507.2
or R905.2, with the following exceptions:
➢ Camelot, Camelot II, Grand Canyon, Grand Sequoia, Grand Sequoia IR, Grand Slate,
Grand Slate II, Country Mansion II and Woodland require minimum five (5) nails per
shingle.
➢ Slateline requires minimum six (6) nails per shingle.
6.3.2 Fasteners shall be in accordance with manufacturer's published requirements, but not less than
FBC 1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of
fastening are required. Contact the shingle manufacturer for details.
6.4 Hip & Ridge Shingles:
6.4.1 Installation of Seal -A -Ridge, Seal -A -Ridge Armorshield and Seal -A -Ridge IR asphalt shingles
shall comply with the manufacturer's current published instructions with a minimum two (2)
nails per shingle.
6.4.2 Installation of Timbertex Hip and Ridge asphalt shingles shall comply with the manufacturer's
current published instructions with a minimum two (2) nails per shingle and beads of
Sonneborn NP1 Gun Grade Polyurethane Sealant or Henkel PL Roofing and Flashing Sealant.
6.4.3 Fasteners shall be in accordance with the manufacturer's published requirements, but not less
than FBC 1507.2.6 or R905.2.5. Staples are not permitted.
7. LABELING:
7.1 Each unit shall bear a permanent label with the manufacturer's name, logo, city, state and logo
of the Accredited Quality Assurance Agency noted herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications
detailed in FBC Table 1507.2.7.1 / R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the
installation of this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule
9N-3 QA requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC — QUA9625; (847) 664-3281
END OF EVALUATION REPORT -
Exterior Research and Design, LLC. Evaluation Report 01506.01.08-1112
Certificate of Authorization #9503 FL10124-R10
Revision 12: 06/21 /2013
Page 4 of 4
Florida Building Code Online.;'—',
Page 1,of 2
Product Manufacturer GAF
Address/Phone/Email 1361 Alps Road
Wayne, NJ 07470
(973) 872-4421
lindareith@trinityerd.com
Authorized Signature Beth McSorley
lindareith@trinityerd.com
Technical Representative Beth McSorley
Address/Phone/Email 1361 Alps Road - Bldg 11-1
Wayne, NJ 07470
(973) 872-4421
BMcSorley@gaf.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Roofing Accessories that are an Integral Part of the Roofing System
Compliance Method Evaluation Report from a Florida Registered Architect or a Licensed
Florida Professional Engineer
(« Evaluation Report - Hardcopy Received
Florida Engineer or Architect Name who
Robert Nieminen
developed the Evaluation Report
Florida License
PE-59166
Quality Assurance Entity
UL LLC
Quality Assurance Contract Expiration Date
05/01/2014
Validated By
John W. Knezevich, PE
(. Validation Checklist - Hardcopy Received
Certificate of Independence FL6267 R6 COI Trinity ERD CI - Nieminen - 2013.pdf
Referenced Standard and Year (of Standard) Standard
Year
ASTM G155
2005
TAS 100(A)
1995
TAS 110
2000
Equivalence of Product Standards
Certified By
http:Hfloridabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDqu02YBW7bM8MZA... 8/23/2013
Florida Building Code Online,, Page 2,of 2
'I
Sections from the Code
Product Approval Method Method 1 Option D
Date Submitted
06/21/2013
Date Validated
06/24/2013
Date Pending FBC Approval
07/01/2013
Date Approved
08/23/2013
Summary of Products
Model, Number or Name
Description
6267.1 =GAF Ventilation Products
Low profile roof ridge vents
Limits of Use
Installation Instructions
Approved for use in HVHZ: No
FL6267 R6 II er061913FINAL GAF Ventilation FL6267-
R6.Ddf
Approved for use outside HVHZ: Yes
Impact Resistant: N/A
Verified By: Robert Nieminen PE-59166
Design Pressure: N/A
Created by Independent Third Party: Yes
Other: Refer to ER Section 5 for Limits of Use.
Evaluation Reports
FL6267 R6 AE er061913FINAL GAF Ventilation FL6267-
R6.Ddf
Created by Independent Third Party: Yes
Back Next
Contact Us :: 1940 North Monroe Street. Tallahassee FL 32399 Phone: 850-487-1824
The State of Florida Is an AA/EEO employer. Copyright 2007-2010 State of Florida.:: Privacy Statement :: Accessibility Statement :: Refund Statement
Under Florida law, email addresses are public records. If you do not want your e-mail address released In response to a public -records request, do not
send electronic mail to this entity. Instead, contact the office by phone or by traditional mall. If you have any questions, please contact 850.487.1395.
*Pursuant to Section 455.275(1), Florida Statutes, effective October 1, 2012, licensees licensed under Chapter 455, F.S. must provide the Department
with an email address if they have one. The emails provided may be used for official communication with the licensee. However email addresses are public
record. If you do not wish to supply a personal address, please provide the Department with an email address which can be made available to the public.
To determine if you are a licensee under Chapter 455, F.S., please click here .
Product Approval Accepts:
rCredf bra
EW
http://floridabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDqu02YBW7bM8MZA... 8/23/2013
EVALUATION REPORT
GAF
1361 Alps Road, Building 7-3
Wayne, NJ 07470
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT #13
OXFORD, CT 06478
PHONE: (203) 262-9245
FAX: (203) 262-9243
Evaluation Report 01506.02.06-R6
FL6267-R6
Date of Issuance: 02/28/2006
Revision 6: 06/19/2013
SCOPE:
This Evaluation Report is issued under Rule 9N-3 and the applicable rules and regulations governing
the use of construction materials in the State of Florida. The documentation submitted has been
reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and
Florida Building Code, Residential Volume. The products described herein have been designed to
comply with the 2010 Florida Building Code sections referenced herein.
DESCRIPTION: GAF Roof Ventilation Products
LABELING: Each unit shall bear labeling in accordance with the requirements the Accredited Quality
Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s)
changes, the referenced Quality Assurance documentation changes, or provisions of the Code that
relate to the product change. Acceptance of this Evaluation Report by the named client constitutes
agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality
Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation
Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may
be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it
shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by
the manufacturer or its distributors and shall be available for inspection at the job site at the
request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized
by Robert Nieminen, P.E. on 06/19/2013
This does not serve as an electronically signed
document. Signed, sealed hardcoples have been
transmitted to the Product Approval Administrator and
to the named client
CERTIFICATION OF INDEPENDENCE:
1. TrinityJERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity IERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which
the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
QOMN-ITYJERD
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Roofing Accessories that are an Integral Part of the Roofing System
Compliance Statement: GAF Roof Ventilation Products, as produced by GAF, have demonstrated
compliance with the following sections of the Florida Building Code through testing in accordance with
the following Standards. Compliance is subject to the Installation Requirements and Limitations /
Conditions of Use set forth herein.
2. STANDARDS:
Section
Property
Standard
Year
1523.6.5.2.13
Wind Driven Rain
TAS 100(A)
1995
1523.6.5.2.13.1
Physical Properties
TAS 110
2000
2612.2
Weatherometer
ASTM G155
2005
3. REFERENCES:
Entity
Examination
Reference
Date
ATI (TST 1558)
Physical Properties
01-49035.01
03/02/2004
ATI (TST 1558)
Wind Driven Rain
01-44964.01
01 /15/2004
ATI (TST 1558)
Wind Driven Rain
60172.01-122-18
10/07/2005
ATI (TST 1558)
Physical Properties
59665.02-106-31
09/16/2005
ATI (TST 1558)
Wind Driven Rain
84608.01-106-18
11 /12/2008
ATI (TST 1558)
Wind Driven Rain
A5250.01-109-18
02/18/2011
PRI (TST 5878)
Weatherometer
HBP-007-02-01
06/24/2004
PRI (TST 5878)
Physical Properties
HBP-002-02-01
06/06/2001
PRI (TST 5878)
Wind Driven Rain
HBP-01-02-01
11/02/2000
PRI (TST 5878)
Wind Driven Rain
BRY-021-02-01
12/31/2003
PRI (TST 5878)
Physical Properties
BRY-025-02-01
09/17/2004
PRI (TST 5878)
Physical Properties
GAF-138-02-06
02/09/2007
PRI (TST 5878)
Wind Driven Rain
GAF-138-02-04
02/09/2007
PRI (TST 5878)
Wind Driven Rain
GAF-310=02-01
07/07/2011
ETC Labs (TST 2411)
Physical Properties
ETC-01-718-10379.0
01 /16/2000
ETC Labs (TST 2411)
Physical Properties
ETC-03-718-14602.0
01 /20/2004
ETC Labs (TST 2411)
Physical Properties
ETC-07-718-19959.0
09/27/2007
Miami -Dade (CER 1592)
Various
Various NOAs
Current
UL, LLC. (QUA 9625)
Quality Control
Inspection Report
05/01/2013
4. PRODUCT DESCRIPTION:
4.1 Cobra® Exhaust VentTM is a low -profile attic ridge vent of mesh -construction for use in shingle
roof systems. The product measures 10'/2-inch wide supplied in 20 and 50 ft long rolls.
4.2 Cobra@ Rigid Vent 3TM is a plastic, low -profile attic ridge vent for use in shingle roof systems
with 12-inch width ridge caps. The product measures 13-13/16-inch wide supplied in 48-inch
long sections, and is supplied with 3-inch ring shank nails.
4.3 Cobra@ Rigid Vent 3TM - 9" is a plastic, low -profile attic ridge vent for use in shingle roof
systems with 10-inch width ridge caps. The product measures 11'/2-inch wide supplied in 48-
inch long sections, and is supplied with 3-inch ring shank nails.
4.4 Cobra@ Snow CountryTM is a plastic, low -profile attic ridge vent with filter for use in shingle
roof systems. The product measures 13-13/16-inch wide supplied in 48-inch long sections
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 2 of 8
QOTRINITYIERD
4.5 Cobra@ Snow Country Advanced TM is a plastic, low -profile attic ridge vent with filter for use
in shingle roof systems with 12-inch width ridge caps. The product measures 13-13/16-inch
wide supplied in 48-inch long sections, and is supplied with 3-inch ring shank nails.
4.6 Cobra@ Snow Country Advanced TM - 9" is a plastic, low -profile attic ridge vent with filter for
use in shingle roof systems with 10-inch width ridge caps. The product measures 11'h-inch
wide supplied in 48-inch long sections, and is supplied with 3-inch ring shank nails.
4.7 Cobra® Ridge RunnerTM is a polypropylene plastic, low -profile attic ridge vent for use in
shingle roof systems. The product measures 11'h-inch wide supplied in 20 ft long rolls.
4.8 TruSlateO Ridge Vent is a plastic, low -profile attic ridge vent for use in TruSlatea roof
systems. The product measures 11.4-inch wide supplied in 48-inch long sections.
5. LIMITATIONS:
5.1 This Evaluation Report is not for use in the HVHZ
5.2 Minimum slopes are as follows:
Product
Minimum Slope
Cobra® Exhaust Vent
2:12
Cobra® Rigid Vent 3TM
3:12
Cobra® Rigid Vent 3TM - 9"
3:12
Cobra@ Snow CountryTM
3:12
Cobra® Snow Country Advanced TM
3:12
Cobra® Snow Country Advanced TM - 9"
3:12
Cobra@ Ridge Runner TM
3:12
TruSlate® Ridge Vent
5:12
5.3 The maximum mean roof height for Cobra® Exhaust Vent, Cobra® Rigid Vent 3, Cobra®
Rigid Vent 3 - 9", Cobra® Snow Country, Cobra® Snow Country Advanced, Cobra® Snow
Country Advanced - 9", Cobra® Ridge Runner and TruSlate@ Ridge Vent shall be 33 ft.
5.4 Installation shall result in minimum net free ventilation area requirements set forth in FBC
Sections 1203.2 and 2326.3.2, with not less than 50% of ventilation from soffit or cornice
vents. When more than one level of roof ridge existing over a single attic space, use ridge
vents only at the high ridge.
6. INSTALLATION:
6.1 GAF Roof Ventilation Products shall be installed in accordance with GAF published installation
requirements subject to the Limitations set forth in Section 5 herein and the specifics noted
below.
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 3 of 8
j
C�Q
TRIM- Y I ERD
6.2 COBRA@ EXHAUST VENT:
6.2.1 Chalk a cut -line 1-inch off each side of the ridge and cut a slot along the apex of the roof
measuring 2-inch (for truss construction) or 3Y2-inch (for ridge pole construction). The slot
should terminate 6-inches from each end and 12-inches from hip intersections or chimneys.
Cut only the sheathing; do not cut trusses. Figure A.
6.2.2 Unroll the vent along the entire length of the ridge, covering uncut 6-inch sheathing area on
both ends. Shorter lengths can be joined by caulking and butting the ends. Figure B.
6.2.3 Apply a bead of polyurethane roof sealant to the underside of the entire perimeter of the vent
and nail with min. 2'h-inch galvanized roofing nails at each corner and 10-inch o.c. Do not
use excessive roof cement, as it may result in shingle blistering.
6.2.4 Apply a bead of polyurethane roof sealant in the shape of a "C" to the underside of the entire
perimeter of the cap shingles, and install cap shingles directly over the vent using Smart
Nails"' or 13/4-inch coil nails (supplied with the vent). Figure C. Do not use excessive roof
cement, as it may result in shingle blistering.
6.2.5 Cobra® Exhaust Vent (hand nail version) and Cobra® Exhaust Vent (nail gun version) have a
3/4-inch or 5/8-inch nominal thickness, respectively, to facilitate ventilation. Care shall be
taken not to crush or compact the product during installation. Figure D.
Hand -Nail Version
Exterior Research and Design, LLC.
Certificate of Authorization #9503
Nail Gun Version
Evaluation Report 01506.02.06-R6
FL6267-R6
Revision 6: 06/19/2013
Page 4 of 8
6.3
6.3.1
6.3.2
6.3.3
\I TRINITY I ERD
COBRA® RIGID VENT 3Tm, RIGID VENT 3Tm - 9"r SNOW COUNTRYTm. SNOW COUNTRY ADVANCED TM
AND SNOW COUNTRY ADVANCEDTm - 9":
Mark -off and cut the slot opening as follows, ensuring that the ends of the opening stop at
least 6-inch from any end walls and at least 12-inch from hip and ridge intersections or
chimneys.
➢ No Ridge Board: Cut a 7/8-inch opening on each side of the ridge (Figure A).
➢ With Ridge Board: Cut a 1-5/8-inch opening on each side of the ridge (Figure B).
13/4'
No Ridge Board
191 1 %11
31/4
With .RWOe Board
Sealant: Apply a bead of silicone caulking or roof cement to the underside of the outer baffle
along both edges and at exposed ends, ensuring the outside edges where the vent meets the
shingles are sealed with the caulk or flashing cement.
Vent Placement: Starting at one end of the slot, place, center and conform the Cobra®
rigid vent over the slot with the vent firmly against the roof surface, ensuring the vent
extends past the slot opening by at least 6-inch.
6.3.4 Fasteners: For Cobra® Rigid Vent 3T11, Cobra® Rigid Vent 3Tm - 9", Cobra® Snow Country
AdvancedTm and Cobra® Snow Country Advanced TM - 9" only, use the E-Z NailTm system.
Grasp attached nails by the head and peel back. Rotate nail to vertical position for easy
removal. For Cobra® Snow CountryTM, use nails at least 13/4-inch or longer. Nails must
always penetrate through plywood decks or at least 3/4-inch into wood planks. NOTE: GAF
recommends 3-inch ring shank nails for increased uplift resistance.
6.3.5 Spacing: Attach the vent section through the pre -molded nailing holes located at 3, 12, 24,
36 and 45-inch from the start of each 48-inch vent piece.
6.3.6 Joints: Apply the subsequent Cobra® rigid vent sections over the length of the ridge using
the overlap/underlap tabs.
6.3.7 Ridge Shingles: Install ridge shingles in accordance with shingle manufacturer's published
installation instructions, using nails detailed in 6.3.4. A nail line is inscribed on top of the
Cobra@ rigid vent to serve as a guide.
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 5 of 8
i
C)o
TRIM-r j ERD
6.4 COBRA® RIDGE RUNNERTM
6.4.1 Cut slot per 6.3.1.
6.4.2 Tear a 1-foot section to be used as a template for laying the vent out (Figure E-G) and center
the template/ locator over the ridge cap shingles at the beginning of the vent slot. Note the
location of the baffle (Figure H). Make sure to do this at both ends of the installation.
6.4.3 Measure the distance from the edge of the roof slot to the exterior baffle (D). Establish a
chalk line along one side of the ridge (Figure 1). Unroll the vent and use the included 1-3/4-
inch pneumatic roofing nails to attach the first side of the ridge vent with the exterior of the
baffle aligned with the chalk line (Figure J). Proceed with using the V interval EasyTearTM
system to custom size the vent to the appropriate length. If the EasyTearTM system can not be
utilized, use a utility knife to size the vent. Nail gun targets are embossed on the part as a
guide for property attaching vent to the roof. The vent should be fastened on 6-inch centers
(Figure K).
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 6 of 8
C)o
TRINITY I ERD
6.4.4 NOTE: When fastening the vent and cap shingles, be sure that the included 1 3/4-inch coil
nails completely penetrate plywood or provide at least 3/4-inch penetration into wood planks.
In the case they do not, you must use alternate nails that provide the required penetration.
Proceed with attaching the other side of the vent. When beginning to nail down the second
side, do NOT begin at the end; begin between the first and second one -foot sections and then
return to fasten the first one -foot section. This will allow for proper fit.
6.4.5 Install ridge shingles in accordance with shingle manufacturer's published installation
instructions, using the nail -lines on top of the ridge vent for proper lapping.
6.5 TRUSLATEO RIDGE VENT:
6.5.1 DO NOT use on hips.
6.5.2 Intall TruSlate@ Ridge Vent before installing the field slates.
6.5.3 After determining the total length of TruSlate@ Ridge Vent required (for proper ventilation),
determine the necessary slot opening. Mark -off and cut the slot opening, ensuring the ends
of the opening stop at least 6-inch from any end walls and at least 12-inch from hip and ridge
intersections or chimneys.
6.5.3.1 Roofs without a ridge board: Cut a 7/8-inch opening along the ridge on each side (Figure A).
6.5.3.2 Roofs with a ridge board: Cut a 1-5/8-inch opening along the ridge on each side (Figure B).
I
(22 mm)lle I/a (22 mm)
13/4".(44:mm)
No Ridge Board
Fig'. B
141 m,.)1 �s" 18'a (41 MM
3Yf (62mm)
With Ridge Board
6.5.4 Install an 18-inch wide section of ASTM D1970 self -adhering leak barrier (holding Florida
Statewide Product Approval or Approved on a Local Basis) from the edge of the ridge slot
extending down towards the roof deck on both side of the slot.
6.5.5 Place the TruSlate@ Ridge Vent over the ridge slot, "peaked" and centered over the ridge slot,
and attach using minimum 3-inch long ring -shank nails through the pre -molded nail holes on
the vent, located 3-inch from the ends and 9-inch o.c. Fasteners shall penetrate through
plywood decks or embed minimum 3/4-inch into wood plank decks.
6.5.6 Continue over the length of the ridge, utilizing the male/female connectors to connect units.
Ensure the finished ends include the pre -molded end caps. Cover all exposed nail heads on
the vent with silicone caulk. Intall a bead of exterior grade silicone sealant at the downslope
leading edges of the ridge vent, at the junction of the leading edge and the leak -barrier
below.
6.5.7 Install the top course of TruSlate@ field slates, UnderBlockTM UV & Moisture Barrier and
TruSlate@ trim slates in accordance with GAF published installation instructions. Intall
TruSlate® .trim slates with 10-inch exposure using minimum 1-5/8-inch long deck screws
through pre -drilled holes, through the ridge vent to engage the wood deck.
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 7 of 8
i
(`n
RaM Dock Pr010GOW
fas�,�
YVeatherkYatdi�or .
SformGuartl� Lriak 9arrwr
ME
7. LABELING:
Each unit shall bear a permanent label with the manufacturer's name, logo, city, state and logo of the
Accredited Quality Assurance Agency noted herein.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the
installation of this product.
9. MANUFACTURING PLANTS:
Contact the manufacturer or the named QA entity for information on plants covered under Rule 9N-3
QA requirements.
10. QUALITY ASSURANCE ENTITY:
UL, LLC. — QUA9625; (847) 664-3281
- END OF EVALUATION REPORT -
Exterior Research and Design, LLC. Evaluation Report 01506.02.06-R6
Certificate of Authorization #9503 FL6267-R6
Revision 6: 06/19/2013
Page 8 of 8