Loading...
HomeMy WebLinkAboutproduct approval 'X -� 'ij. , C MiAMNtaADE 0 .Y MIAMI-DADS COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF PERMITTING,ENVIRONMENT,AND REGULATORY 11805 SW 26 Street,Room 208 AFFAIRS(PERA) Miami,Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamt4ade.g_rvv/vera/ DAB Door Company,Inc. 12195 NW 91e Avenue Hialeah Gardens,FL 33018 SCOPE:This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The documentation submitted has been reviewed and accepted by Miami-Dade County PERA-Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHI). This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section(In Miami Dade County)and/or the AHJ (in areas other than Miami Dade County)reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify,or suspend the use of such product or material within their jurisdiction. PERA reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein,and has been designed to comply with the Florida Building Code,including the High Velocity Hurricane Zone. DESCRIPTION:91-4"Wide x 16'High Steel Sectional Garage Door w/Window Lite Option APPROVAL DOCUMENT:Drawing No.01-09,titled"Sectional Garage Door",dated 02101/2001,with last revision F dated 10/1312011,sheets 1 through 5 of 5,prepared by Al-Farooq Corporation,signed and sealed by Javad Ahmad,P.E.,bearing the Miami-Dade County Product Control revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING:A permanent label with the manufacturer's name or logo,manufacturing address,model number,the positive and negative design pressure rating,indicate impact rated if applicable,installation instruction drawing reference number,approval number(NOA),the applicable test standards,and the statement reading`Miami-Dade County Product Control Approved' is to be located on the door's side track, bottom angle,or inner surface of a panel. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County,Florida,and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done in its entirety. INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA#11-0119.21 and consists of this page I and evidence pages E-1 and E-2,as well as approval document mentioned above. The submitted documentation was reviewed by Carlos M.Utrera,P.E. NOA No.12-0110.06 Expiration Date:August 9,2016 4 f Approval Date:March 1,2012 �Z/� Page 1 DAB Door Comyany,Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No.01-09,titled"Sectional Garage Door",dated 02101/2001,with last revision F dated 10/13/2011, sheets 1 through 5 of 5,-prepared by Al-Farooq Corporation,signed and sealed by Javad Ahmad,P.E. B. TESTS "Submitted under N©A#U9-o12804" 1. Test reports on 1)Uniform Static Air Pressure Test,Loading per FBC TAS 202-94 2)Large Missile impact Test per FBG,TAS 201-94 3)Cyclic Wind Pressure Loading per FBC,TAS 203-94 4)Forced Entry Test,per FBC 24113.2.1,TAS 202-94 along with marked up drawings and installation diagram of a DAB 824 24 GA Sectional Garage Door with Fixed Windows,prepared by Hurricane Engineering& Testing,Inc,Test Reports No.HETI-08-2149A/B,dated 06127/2008, signed and sealed by Candido F. Font,P.E. "Submitted under NOA#09-012$.04" 2. Test report of Tensile Test per ASTM E 8,Report No.HETI 08-TI82,prepared by Hurricane Engineering & Testing, Inc., dated 1212312008, signed and sealed by Candido F. Font,P.E. "Submitted under NOA#03-0210.04» 3. Test report on Salt Spray(Corrosion)Test per ASTM B 117 of a painted G-40 steel panels,prepared by Celotex Corporation,Test Report No.258592,dated 08/17/1998, signed by W. A. Jackson,P.E. C. CALCULATIONS "Submitted under NOA#09-0128 04" 1. Anchor verification calculations prepared by AI-Farooq Corporation,complying with F.B.0 2007,dated 12/19108,signed and sealed by Humayoun Farooq,P.E. D. QUALITY ASSURANCE 1. Miami-Dade Department of Permitting;Environment,and Regulatory Affairs(PERA) rlos .TArera,P.E. Product Control Examiner NOA Na 12-011&06 Expiration Date:August 9,2016 Approval Date:March 1,2012 E-1 DAB Door Qmvany,Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 08-0305.02,issued to SABIC Innovative Plastics,for their Lexan Sheet Products,approved on 04/2412008 and expiring on 07117/2013. 2. Notice of Acceptance No. 07-1016.07,issued to Insulfbam,LLC,for their Insulfbam Expanded Polystyrene Insulation,approved on 11/29/2007 and expiring on 11/2912012. 3. Notice of Acceptance No. 07-1107.08,issued to Dyplast Products,LLC,for their Expanded Polystyrene Block Type Insulation,approved on 04/26/2007 and expiring on 08127/2008. 4. Notice of Acceptance No. 07-0301.10,issued to Dyplast Products,LLC,for their Dyplast ISO-CI Polyisocyanurate Insulation,approved on 06/07/2007 and expiring on 01/11/2012. "Submitted under NOA#05-0228.02" 5. Test Report on Accelerated Weathering Using Xenon Arc Light Apparatus Test per ASTM G155 of"PVC Extrusion Material",prepared by Hurricane Engineering& Testing,Inc.,Report No. HETI 04-A002,dated 09/27/2004,signed and sealed by Rafael E.Droz-Seda,P.E. 6. Test Reports on Tensile Test per ASTM D638 of"PVC Extrusion Material",prepared by Hurricane Engineering&Testing Inc.,Report No. HETI 04-T251,dated 11/29/2004 signed and sealed by I.Ghia,P.E. 7. Test Report on Self-Ignition Temperature Test, Rate of Bum Test and Smoke Density Test of"REHAU non-foam PVC extrusion material",prepared by ETC Laboratories, Report No.04-761-15019.0,dated 05/06/2004,signed and sealed by J.L. Doldan,P.E. F. STATEMENTS 1. Statement letter of code conformance to 2010 FBC and no financial interest,issued by Al-Farooq Corporation,dated 10126/2011,signed and sealed by Javad Ahmad,P.E. 02 f Zj� 17- Carlos M.Utrera,P.R. Product Control Examiner NOA No.12-0110.06 Expiration Date:August 9,20'16 Approval Date.March 1,2012 9-2