HomeMy WebLinkAboutCorrected Product Approval ® 8585 Duke Boulevard
® Mason,Ohio 45040-3101 USA
BUILDING PRODUCTS (513)770.4800 - Fax(513)770-3558
ACrffcn Compmd
December 15, 2011
Evaluation Report for Clopay Building Products Company Sectional Garage Doors, W7
through W9
I have evaluated the wind load door designs as shown on the drawings listed below. I
have reviewed the test reports, which were generated by accredited independent
laboratories as required by 9N-3.005(4), the engineering rational analysis, and the
product drawings. The test reports are listed below. Testing was conducted by
American Test Lab North Carolina and Hurricane Engineering and Testing Inc.
For the doors listed in the Tables below, Static Pressure Tests were conducted in
accordance with TAS 202, ASTM-E330 and ANSI/DASMA 108. Missile Impact and Cyclic
Pressure Tests were conducted in accordance with TAS 201 and TAS 203 and
ANSI/DASMA 115. The pressures listed on the drawings are either direct results of
these tests or results obtained through engineering rational analysis based on actual
tests. I have concluded that the door designs listed below in the Tables below are in
compliance with the High Velocity Hurricane Zone test requirements of the 2010 Florida
Building Code Sections 1715.5.3.1, 1625 and 1626 and therefore are qualified as
impact-resistant assemblies.
TABLE 1: Drawings for doors with Manufacturina Product Code (MPC) PAN-2F153:
101702-Revll, max. door size 9'0" x 16'0 , +42/-48 PSP (design load)
101309-Rev15, max. door size 16'2" x 16'0", +42/-48 PSF (design load)
101296-Revl4, max. door size 9'0" x 16'0", +46/-50 PSF (design load)
TABLE 2: Drawings for doors with Manufacturing Product Code (MPC) PAN-2F143:
102621-Rev07, max. door size 18'2" x 16'0", +42/-46 PSF (design load)
103287-RevO4, max. door size 9'0" x -16:0", +54/-62 PSF (design load)
103547-Rev05, max. door size 9'0" x 160", +48/-54 PSF (design load)
101300-Revl6, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
101706-Rev13, max. door size 9'0" x 16'0", +62i-72 PSF (design load)
TABLE 3: Drawings for doors with Manufacturing Product Code (MPC) DSIE-1F171:
101703-Revll, max. door size 9'0" x 16'0", +48/-60 PSF (design load)
101488-Rev13, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
103028-RevOS, max. door size 18'2" x 1610", +46/-50 PSF (design load)
TABLE 4: Drawings for doors with Manufacturing Product Code (MPC) DSIEO-1M479:
103436-Rev02, max. door size 9'0" x 1610", +48/-60 PSF (design load)
103560-Rev04, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
TABLE 5: Drawings for doors with Manufacturing Product Code (MPC) C-DSIE-1F447:
101705-Rev08, max. door size 12'2" x 18'0", +52/-58 PSF (design load)
TABLE 6: Drawings for doors with Manufacturing Product Code (MPC) C-PAN-1E448:
102645-RevO7, max. door size 12'2" x 18'0", +50/-56 PSF (design load)
103288-Rev03, max. door size 14'2" x 18'0", +50/-56 PSF (design load)
PACE 1 of 5 FILE: CBPC 111215-A.DOC
C1®pUY
EVALUATION REPORT FOR CLOPAY BUILDING PRODUCTS COMPANY SECTIONAL GARAGE DOORS,w7—w9
TABLE 7: Drawings for doors with Manufacturing Product Code (MPC) PAN-2F443:
104067-Rev2, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
104121-Rev01 max. door size 9'0" x 16'0", +50/-58 PSF (design load)
TABLE 8: Drawings for doors with Manufacturing Product Code (MPQ DSIE-iF471:
104038-Rev02, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
TABLE 9: Drawings for doors with Manufacturina Product Code (MPG) DSIU-1F171:
104185-Rev01, max. door size 9'0" x 16'0 , +48/-50 PSF (design load)
104280-Rev01, max. door size 16'2" x 16'0", +46.6/-52 PSF (design load)
104281-ReV01, max. door size 18'2" x 16'0", +46/-50 PSF (design load)
TABLE 10: Drawings for doors with Manufacturing Product Code (MPC DSIUO-1K479:
104277-RevO2, max. door size 9'0" x 16'0 , +54/-60PSF (design load)
104278-Rev02, max, door size 16'2" x 16'0", +46.6/-52 PSF (design load)
TABLE 11: Drawings for doors with Manufacturing Product Code (MPC) C-DSIU-1F447:
104112-ReV00, max. door size 16'2" x 18'0'x, +50/-56 PSF (design load)
TABLE 12: Drawings for doors with Manufacturing Product Code (MPC) C-DSIU-1D447:
104245-Rev01, max. door size 12'2" x 18'0' , +52/-58 PSF (design load)
Test Reports:
ATL 0428.01-09; ATL 1112.01-96, 0808.01-06; 0305.01-08; HETI 95-494, 95-496,
ATL 0808.01-06; ATL 0924.02-02; ATL 0823.01-06; HETI 94-252, 94-254,
ATL 0808.01-06; ATL 0827.01-04; ATL 1008.01-07; ATL 0606.01-05; ATL 0107.01-09;
HETI 02-1267, 02-1268, ATL 1018.01-04; ATL 1018.01-04; ATL 0415.01-08;
ATL 0331.01-08; ATL 1106,01-07; ATL-0128.01-08; ATL 0327,01-08; HETI 03-1.358,
03-1359; ATL 0610.01-08; ATL 1202,01.-08, ATL 1210.01-08; ATL-0609.01-09;
ATL 0415.01-08; HETI 03-1358, 03-1359; ATL 0606.01-05; ATL 1106.01-07;
ATL 0512,01-09; ATL 0127.01-09.
Product Description for doors with MPC PAN-2F153:
These doors consist of 2"thick steel pan sections with min. 25 ga. (0.019")
skins. The steel skin is at least G40 DDS per ASTM A653. The maximum section height
is 21 These doors may have optional Impact-Resistant Glazing in either the top
section or the next-to-the-top section. Optional Impact-Resistant Glazing is a one-piece
injection-molded front frame and glazing. The following models are at least structurally
equivalent to the tested door: 73, 75, 6RST, 42, 42B, 84A, 94, 98, 4RST, 4F, 48, 48B,
1500, 190, 55, 55S.
Product Description for doors with MPC PAN-2F143:
These doors consist of 2" thick steel pan sections with min. 24 ga. (0.0239")
skins. The steel skin is at least G40 DDS per ASTM A653. The maximum section height
is 21". These doors may have optional Impact-Resistant Glazing in either the top
section or the next-to-the-top section. Optional Impact-Resistant Glazing is a one-piece
injection-molded front frame and glazing. The following models are at least structurally
equivalent to the tested door: 84A, 94, 98, 4RST, 4F, 48, 48B.
PAGE 2 OF 5 FILE:CBPC_111215-A.DOc
Cl0pay
EVALUATION REPORT FOR CLOPAY BUILDING PRODUCTS COMPANY SECTIONAL GARAGE DOORS,W7-W9
Product Description for doors with MPC DSIE-1F171:
These doors consist of 2"double-skin insulated sections with an EPS core
laminated to both skins. Both inner and outer skins are min. 27 ga. (0.01611) G40 DDS
per ASTM A653. The maximum section height is 21".The following models are at least
structurally equivalent to the tested door: 4300, 4301, 4310, 4400, 4401, HDG, HDGL,
HDGF, 66,-66G, 67, 67G, 68, 68G, 6200, 6201, 6203, SP200, SF200, SE200.
Product Description for doors with MPC DSIEO-1M479:
These doors consist of a base 2" double-skin insulated section with an EPS core
laminated to both skins. Decorative overlays are attached to the exterior skin, adding
not more than 5/8" to the total thickness. Both inner and outer skins are min. 27 ga.
(0.016") G40 CS Type B per ASTM A653. The maximum section height is 24". The
following models are at least structurally equivalent to the tested door: CGnn, CPnn,
HPnn, CXnn, SXnn, AGnn. Note that`nn' represents the arrangement of the decorative
overlays. The first digit will have a value from 1 to 3 and the second digit will have a
value from 1 to 5.
Product Description for doors with MPC C-DSIE-1F447•
These doors consist of 2"thick steel pan sections with min. 24 ga. (0.019")
exterior and 27 ga. (0.016") interior skins. The steel skin is at least G40 CS-B per
ASTM A653. The maximum section height is 24". The following models are at least
structurally equivalent to the tested door: 3200, 3220, 240.
Product Description for doors with MPC C-PAN-1E448:
These doors consist of 2" thick steel pan doors with min. 24 ga. (0.022") outer
skins. The steel skin is at least G40 CS-B per ASTM A653. The maximum section height
is 24". The following models are at least structurally equivalent to the tested door: 524,
520, 224, C4ST, COST.
Product Description for doors with MPC PAN-2F443:
These doors consist of 2"thick steel pan doors with min. 24 ga. (0.022") outer
skins. The steel skin is at least G40 DDS. per ASTM A653. The maximum section height
is 24". The following models are at least structurally equivalent to the tested door:
G4S, GS4, GD4S, GR4S, E4S, ED4S, SS4r.AR4S.
Product Description for doors with MPC DSIE=1F471•
These doors consist of 2" double-skin insulated sections with an EPS core
laminated to both skins. Both inner and outer skins are min. 27 ga. (0.016") G40 DDS
per ASTM A653. The maximum section height is 24". The following models are at least
structurally equivalent to the tested door: GD2SP, GR2SP, GD2LP, GR21 Pi AR2SP,
AR2LP, ED2SP, ED2LP.
Product Description for doors with MPC PAN-2F151
These doors consist of 2"thick steel pan doors with min. 25 ga. (0.019") outer
skins. The steel skin is at least G40 DDS per ASTM A653. The maximum section height
is 21". The following models are at least structurally equivalent to the tested door: 76.
PAGE 3 of 5 FILE:CBPC 111215-A.DOC
l Clopay
EVALUATION REPORT FOR CLOP"BUILDING PRODUCTS COMPANY SECTIONAL.GARAGE DOORS,W7—W9
Product Description for doors with MPC DSIU-1F171:
These doors consist of 2" double-skin insulated sections with polyurethane
Insulation foamed in place between both skins. Both inner and outer skins are min. 27
ga. (0.016") G40 DDS per ASTM A653. The maximum section height is 21". These
doors may have optional Impact-Resistant Glazing in either the top section or the next-
to-the-top section. Optional Impact-Resistant Glazing is a one-piece injection-molded
front frame and glazing. The following models are at least structurally equivalent to the
tested door: HDP20, HDPF20, HDPL20, 7200, 7201, 7203, 8200, 8201, 8203, 9200,
9201, 9203.
Product Description for doors with MPC DSIUO-IK479:
These doors consist of a base 2" double-skin insulated section with polyurethane
insulation foamed in place between both skins. Decorative overlays and optional
cladding are attached to the exterior skin, adding not more than 1"to the total
thickness. Both inner and outer skins are min. 27 ga. (0.016") G40 CS Type B per
ASTM A653. The maximum section height is 24". The following models are at least
structurally equivalent to the tested door: CAN2nn, CAN2nn-N, BRK2nn, BRK2nn-N.
Note that`nn' represents the arrangement of the decorative overlays. The first digit will
have-a value from 1 to 3 and the second digit will have a value from 1 to 8.
_Product Description for doors with MPC C-DSIE-1F447•
These doors consist of 2"double-skin insulated sections with an EPS core
laminated to both min. 24 ga. (0.019") exterior and 27 ga. (0.016") interior skins. The
steel skins are at least G40 CS-B per ASTM A653. The maximum section height is 24".
The following models are at least structurally equivalent to the tested door: 3200,
3205, 3220, 240, 240G.
Product Description for doors with MPC C-DSIU-1F447•
These doors consist of a base 2" double-skin insulated section with polyurethane
insulation foamed in place between both skins. Both inner and outer skins are min. 27
ga. (0.016") G40 CS Type B per ASTM A653. The maximum section height is 24". The
following models are at least structurally equivalent to the tested.door: 3720, C7X20,
2400, 3722, COX22.
Product Description for doors with MPC C-DSIU-1D447.,
These doors consist of a base 1-3/4" (min.) double-skin insulated section with
polyurethane insulation foamed in place between both skins. Both inner and outer skins
are min. 27 ga. (0.016") G40 CS Type B per ASTM A653. The maximum section height
is 24". The following models are at least structurally equivalent to the tested door:
3717, C7X17, 3718, C7X18, 3720, C7X20, 240U, 3722, COX22.
Limitations:
The drawing(s) cited above are an explicit part of this evaluation report. The
text of this report does not attempt to address all design details and relies on the
illustrations and text of these drawings as well.
Jambs, lintels, sills or other structural elements required to prepare openings
are not covered. The design of the supporting structural elements shall be the
responsibility of the professional of record for the building or structure and in
PAGE 4 of 5 FILE:CBPC_111215-A.DOc
`
M
MCIDPW
EVALUATION REPORT FOR CLOPAY BUILDING PRODUCTS COMPANY SECTIONAL GARAGE DOORS,W7-_W9
accordance with current building,codes for the loads listed on the drawing(s) referenced
above.
Installation requirements per 9N'3.0OS including attachments, are
detailed onthe dnywAng/slUstedabove. InStaUaUonrnustbe |naccordance vVith
noaVUfacturer'sinstallation� ' instructions and must beuashown onthe dnawing(s) listed
above. The manufacturer's licensed design professional listed oUthe dnaVv|og(a) has
reviewed the attachment details and installation requirements.,
' r^ /
'
PAGE 5op5 RLE:CepC_111215-A.c)uc