HomeMy WebLinkAboutNotice of Acceptance p
MN r
MIAMI-
DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES.(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/economy
Polyglass USA,Inc.
150 Lyon Drive -
Fernley,NV 8.9.408
:.SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has.been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance.purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self-Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following
statement: "Miami-Dade County Product ControlApproved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance.of this product.
._ TERMINATION of this NOA will occur after the expiration date or'if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product;
for sales, advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the.
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it.shall be done
in its entirety:
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
.This renews NOA# 12-081.8.07 and consists of pages 1 through 26. .
The submitted documentation.was reviewed by Alex Tigera.
' NOA No.: 13-0514.10
MIAMI•DADeCouN7Y Expiration Date: 10�17I7
Approval Date:09/26/13
Page 1 of 26
i
4
ROOFING.ASSEMBLY APPROVAL
CategorV: Roofing
Sub-Category: Modified Bitumen
Materials. SBS/APP/TPO
Deck Tyne: Wood
Maximum Design Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Elastobase 65' 2"x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Type I base sheet.
Elastobase P 5' 2"x 3' 3-3/8" ASTM D 6164, SBS modified asphalt coated polyester reinforced base
Type I sheet.
Elastoflex SA V FR 32' 6"x3' 3-3/8" ASTM D 6163, Self-adhered;fiberglass reinforced, SBS modified
(1.5-mm) Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V 32' 6"x 3' 3-3/8" ASTM D 6163, Self-adhered,fiberglass reinforced, SBS modified
PLUS FR Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V(1.5- 32' 6"x3' 33/8" ASTM D 6163, Self-adhered,fiberglass reinforced, SBS modified
mm) Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SAV 32' 6"x 3' 33/8" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
PLUS Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA P FR 32' 6"x 3' 3-3/8". ASTM D 6164, Self-adhered,polyester reinforced, SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Elastoflex SA P 32"6"x 3' 3-3/8" ASTM D 6164, Self-adhered,fiberglass reinforced, SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P 32'.6"x 3' 33/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P FR 32' 6"x 3' 33/8" ASTM D.6222, Self-adhered,polyester reinforced,APP modified
Type I. bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko SBS SAP 32' 6"x 3' 33/8". ASTM D 6164, Self-adhered, fiberglass reinforced, SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
NOA No.: 13-0514.10
Miar��•n�e COUNTY Expiration Date: 10/11/17
Approval Date:09/26/13
Page 2 of 26
Polyfresko SBS SAP 32' 6"x 3' 33/a" ASTM D 6164, Self-adhered,fiberglass reinforced, SBS modified
FR Type I bitumen membrane with a self-adhering,back face and
a granule top surface.
Polyffesko APP SAP 32' 6"x 3' 3-3/S" ASTM D 6222, Self-adhered,polyester reinforced,.APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko APP SAP 32' 6"x 3' 3-3/8" ASTM D 6222, Self-adhered,.polyester reinforced,APP modified.
FR Type I bitumen membrane with a self-adhering back face and
a granule top surface
PolyKool 32' '10"x 3' 33/8" ASTM D6222 Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
PG325 Cold Process, 1,3, 5, 50, 55 gal.or ASTM D3019 A fibered cold process adhesive for use with roll or
_Adhesive tube Type III BUR roofing.
PGI 00 Asphalt Primer 1,3,5, 50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of
tube or 17 oz. spray: selected asphalts used to promote adhesion.
can .
PG350.Mod Bit 1,3,5,50,55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with
Adhesive i tube Type III, modified bitumen membranes..
PG400 Plastic Roof 1,3, 5,50,55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 dry or damp conditions.
PG425 Wet/Dry Roof 1,3,5, 50, 55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 dry or damp conditions.
PG450 Flashing 1,3,5, 50,55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement.
Cement tube
PG500 MB Flashing 1,3, 5,50,55 gal. or ASTM D4586 A thick, fibered,rubberized flashing cement for use.
Cement 'tube with modified bitumen membranes.
Polyplus 35 Premium 1,3, 5,50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with
Mod Bit Adhesive tube Type III modified bitumen membranes.
Polyplus 45 Premium 1,3,5, 50,55 gal..or ASTM D4586 A thick,fibered,rubberized flashing cement.
Flashing Cement tube
Polyplus 50 Premium 1,3,5, 50, 55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement for use
MB Flashing Cement tube with modified bitumen membranes.
Polyplus 55 Premium 1,3,5, 50, 55 gal. or ASTM D4586 A mastic compound for:use as a roof flashing .
Modified Flashing tube adhesive.
Cement
MIAMI•DADe COUNTY NOA No.: 13-0514,10
Expiration Date: 10/11117
Approval Date:09/26/13
Page 3 of 26
s
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description Manufacturer
(With Current NOA)
Polytherm-H Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm Composite Polyisocyanurate/perlite composite insulation. Polyglass USA,Inc.
ACFoam-II Polyisocyanurate foam insulation Atlas Roofing Corp
ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corp
High Density Wood Fiberboard Wood fiber insulation board Generic
Perlite Insulation Perlite insulation board Generic
Type X Gypsum Fire resistant rated gypsum. Generic
DensDeck,DensDeck Prime Gypsum insulation board Georgia-Pacific
H-Shield Polyisocyanurate foam insulation . Hunter Panels,LLC
H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels,LLC
ENRGY-3,JM ISO 3 Polyisocyanurate foam insulation. Johns Manville Corp.
Fesco Board Expanded mineral fiber Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating,LLC.
SECUROCK Gypsum-Fiber Roof Board Fiber reinforced coverboard United States Gypsum
Corporation.
NOA No.: 13-0514.10
MIAM6DADE COUNTY
Expiration Date: 10/11/17
Approval Date:09/26/13 .
Page 4 of 26
a
APPROVED FASTENERS:
TABLE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NOA)
1. Dekfast Fasteners#12,#14 Insulation fastener for wood, SFS Intec,Inc.
 HS steel and concrete decks
2. Dekfast Galvalume Steel Galvalume hex stress plate. 2'/s" x SFS Intec,Inc.
Hex Plate 3 'V4"
3. Dekfast Dekflat Round Polypropylene locking 3"x 3 '/4" SFS Intec,Inc.
Plastic Lock Plate plate.
4. . #12 Roofgrip Insulation and membrane Various OMG,Inc.
fastener
5: Flat Bottom Metal Plate A2-SS aluminized steel.plate 3" square OMG, Inc.
6. Plastic-Plate Polyethylene stress plate 3.2"round OMG,Inc.
7. Tru-Fast#14 HD Fastener Insulation fastener for steel and Altenloh,Brinck&Co.
wood decks U.S.,Inc.
8. Tru-Fast 3"Metal,Insulation Round Galvalume AZ50 steel 3.23 round Altenloh,Brinck&Co.
Plate plate 3"round U.S.,Inc.
9. Polygrip Fasteners#12,#14 . Insulation fastener for wood, Various Polyglass USA,Inc
 steel and concrete decks
10. Polygrip Hex Plates Galvalume hex stress plate. 2'/S" x Polyglass USA,Inc
3 %4"
H. Dekfast Galvalume Steel 3 3"round galvalume AZ50 steel 3"round SFS Intec,Inc.
in.Round plate
12. Millennium One-Step Insulation Adhesive Various Adco Products
Foamable Adhesive:
NOA No.: 13-0514.10
MItioaoe COU=NTYExpiration Date: 10/11/17
Approval Date:09/26/13
Page 5 of 26
0
APPROVED SURFACING:
TABLE 4
Product Product Application Manufactur
Name Description Rate Specification er
PG200 Non-Fibered Roof Coating A non fibered asphaltic coating used 1'/2-2 gal/sq TAS 140 Polyglass
to add life and rejuvenate existing USA,Inc.
BUR roofing substrates.
PG300 Fibered Roof Coating An asphalt cutback fibered roof 1%2-2 gal/sq ASTM D4479 Polyglass
coating. May be applied by brush or USA,Inc.
spray equipment to rejuvenate aged
BUR
PG600 Non-Fibered Aluminum Non-fibered aluminum roof coating. ''/2-1 gal/sq ASTM D2824 Polyglass
Roof Coating Type I USA,Inc.
P0650 Fibered Aluminum Roof Fibered aluminum roof coating. 1'/2-2 gal/sq ASTM D2824 Polyglass
Coating . . Type III USA,Inc. .
PG700 White Elastomeric Roof A premium white elastomeric acrylic 1-1'/2 gaUsq ASTM D6083 Polyglass
Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
PG800 Non-Fibered Asphalt An asphalt base,un-fibered clay .3 gal/sq in ASTM D 1227 Polyglass
Emulsion Roof Coating emulsion two coats USA,Inc.
PG850 Fibered Asphalt Emulsion An asphalt base,fibered clay 3 gal/sq in ASTM D 1227 Polyglass
.Roof Coating emulsion two coats USA,Inc.
Polyplus.65 Premium Fibered Fibered aluminum roof coating. 1'/2-2 gal/sq ASTM D2824 Polyglass.
Aluminum Roof Coating Type III USA,Inc.
Polyplus 60 Premium Non- Non-fibered aluminum roof coating. '/2-1 gal/sq ASTM D2824 Polyglass
Fibered Aluminum Roof Coating Type I USA,Inc.
Polybrite 70 White Elastomeric A premium white elastomeric acrylic 1-1'/2 gal/sq ASTM D6083 Polyglass
Roof Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
Gravel To be installed in a flood coat of 400 lbs/sq N/A Generic
approved asphalt at 60 lbs/sq
Slag To be installed in a flood coat of 3001bs/sq N/A Generic
approved asphalt at 60 lbs/sq
NOA No.: 13-0514.10.
MLAMIDAoeCouNr'� Expiration Date: 10/11/17
Approval Date:09/26/13
Page 6 of 26
EVIDENCE SUBMITTED:
Test Agency Test Name/Report Report No. Date
Factory Mutual Research 4470 J.I.2W7A7.AM 08.04.94
Corporation . 4450 2D5A9.AM 06.22.99
4470 J.1.3001334 02.15:00
4470 J.1.3000857 01.12.00
4470 . J.1.3004091 01.12.00
4470 3012321 07.29.07
4450 3014751 08.27.03
445.0 3019317 06.30.04
4470 3014692 08.05.03
Trinity I ERD TAS 114 11752.09.99-1 02.08.00
TAS 114 02764.09.05 09.09.05
TAS 114 020843.02.05-1 02.10.05
TAS 114 02762.03.05 03.30.05
TAS 117(B)-ASTM D903 . 020841.06.04 06.02.04
TAS 114 P1734.07.06-R1 02.27.07
TAS 114 02843.07.07 07.23.07
TAS 114 P1738.02.07 02.05.07
TAS 114 P1739.01.07 01.23.07
TAS 117(B)-ASTM D6862 C8500SC.11.07 11.30.07
ASTM D6164/ASTM D6222 P10490.08.08 08.13.08
ASTM D6164/ASTM D6222 P10490.10.08-RI 10.03.08
ASTM D6222 P7400.03.08-R2 10/09/08
TAS 114(D)—ASTM D1876 . P10070.10.08 .. 10/09/08
ASTMD6222 PI0490.10.08-2 10/3.0/08
FM 4470&TAS 114 P33970.03.11 03/15/11
ASTM D6163/ASTM D 4601 P33960.03.11 03/15/11
ASTM D6164 P37590.07.13-1 07/02/13
ASTM D6164 P37590.03.13-3A 03/06/13
ASTM D6163 P37590.03.13-2-R1 02/05/13
ASTM 136222 P37590.09:13 0912/13
PRI Asphalt Technologies ASTM D6222 PUSA-061-02-02 01/28/08
ASTMD6222 PUSA-062-02-02 12/04/08
ASTM D6163 PUSA-064-02-02 02/27/08
��Muu�i•oaoe counrx NOA No.: 13-0514.10
Expiration Date:.10/11/17
Approval Date:09/26/13
Page 7 of 26
{
Membrane Type: SBSIAPP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank,fastened with 8d common nails at 4"o.c. or#8 wood
screws at 6"o.c.
System Type E(3): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply.
Base Sheet: One ply of Elan tobase or Elastobase P fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank and 1-5/8"diameter tin caps spaced 8"o.c. in
a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: . One or more plies of Elastoflex SA V,Elastoflex SA V PLUS,Elastoflex SA V FR,or
Elastoflex SA V PLUS FR self-adhered.
Membrane: One ply of Polyfresko SBS SAP;Polyfresko SBS SAP FR,Polyfresko APP SAP,Polyfresko
APP SAP FR,Elastoflex SAP,Elastoflex SA P FR,Polyflex SA P,PolyKool or Polyflex SA P
FR self adhered.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:_ -60 psf;(See General limitation#7.)
CKAMMI-DMADE=UNTY
NOA No.: 13-0514.10
Expiration Date: 10/11/17,
Approval Date:09/26/13
Page 22 of 26
i
I
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt,panel size
shall be 4'x T maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet.is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side.lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips.is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of-45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force(F')value of 275 lbf.,as
tested in compliance with Testing Application Standard TAS 105. If the fastener value,as field-tested,are below
2751bf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanicalattachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value-in conjunction with the maximum design.value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing,prepared, signed and sealed by a Florida registered Professional Engineer,Registered Architect,or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or:Registered Roof Consultant (When this limitation is specifically referred
within this NOA,General Limitation#9 will not be applicable.)
8. All attachment and sizing of perimeter nailers,metal profile,and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicablewind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones(i.e. field,
perimeters,and corners).Neither rational analysis,nor extrapolation shall be permitted for enhanced fastening at.
enhanced pressure zones(i.e.perimeters,extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation#7 will not be applicable.)
END OF THIS ACCEPTANCE
NOA No.: 13-0514.10
MAMIDAD;COUNTY Expiration Date: 10/11/11
Approval Date:09/26/13
Page 26 of 26