HomeMy WebLinkAboutProduct Approval MIAW:DE MIAMI-DADS COUNTY
A PRODUCT CONTROUSECTION
11805 SW 26 Street,Rbom.208
DEPARTMENT OF REGULATORY-AND ECONOMIC RESOURCES(RER) . Miami,Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)31525.99
'NOTICE OF ACCEPTANCE (NOA) w�w`r.mlamiaaac.gor�ccono»r� : '
CertainTeed Corporation
1400 Union Meeting Road,P.O.Box 1100
Blue Bell,PA 19422-0761
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction.materials.The
documentation submitted'has been reviewed and accepted by Miami-bade County RER-Product Control Section to be
used in Miami Dade County and other.areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested"for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing 'and the AHJ "may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right 10
revoke this acceptance, if itis. determined. by Wami-Dade.County.Product Control Section that this product or
material fails to meet the requirements of the applicable building code,
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High'Velocity Hurricane.Zone of the Florida Building Code.
DESCRIPTION: CertainTeed'.Modified-Bituinen Roofing Systems over Wood Decks.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise Hated harem.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively'affecting the performance of this product.
TERMINATION of this NOA will occur after"the expiration date or if there has:been a revision or change in the
'materials,use,acid/or manufacture of the product or process.'Ivlisuse of this NOA as an endorsement bf any product,
for sales, advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section.
of this NOA shall be cause for terinitiation and reinoval'of NOA.
ADVERTISEIYIENT1. The NOA number preceded by the words Miami-Dade .County, Florida, and followed by the
expiration date may be displayed in advertising literature. If"anyportion of the NOA.is displayed,then it-shall.be done
in its entirety.
a
INSPECTION: A copy-of this entire NOA shall be provided to the user by the mane€acturer or"its distributors and
shall be available for irispection at the job site at the iiequest of the Building.Official.
This NOA renews NOA#13-0204,03 and consists of pages 1 through 16,:
The submitted documentation was reviewed by Alex Tigera. j
NOA.No.: 14-4224.03
CMIAMIDADS COCIF
iExpiration Date: '06119%18
Date:.04/10/14i
Page 1 of 16
ROOFING SYSTEM APPROVAL
Category: Roofing
'Siib-Category: Modified Bitumen
Material: APP/SBS
Deck Type: Wood
Maxhnum.De§ikn Pressure: -60 psf.
TRADE NAMES OF PRODUCTS MANUFACTURI{;D OR LABELED BY APPLICANT:
TABLE 1
Test Piroduci
Product Dimensions Specification Description
All Weather/Empire Base 36" x 65'10'••- ASTM'D 4601 Type Asphalt-coated,fiberglass reinforced
Sheet Rall weight:'86 lbs. -11 base sheet
(2 squares) UL Type 15
Flex-l-GlasTM Base Sheet 36",x 98"9";Roll ASTM D 4601,Type-Modified Bitumen coated fiberglass
Weight: 96 lbs. II base'sheet.
(3 squares). UL Type G2
Flex-I-GIasTM FR Base Sheet 39 378" x 50;Roll ASTM
D 6163, Modified;Bitumen coated.fibergl ass
-weight: 90 lbs. Grade S,Type I Base sheet.
/ --(1.5 squaros)
t FlintglasO PlySheet Type IV 36°x 1647%Roll ASTM D 2178 T e Fiberglass, asphalt im=re naffed ply
yp, , . Yp• g p . p . g py
or VI weight:40/55 lbs. IV or VI sheet.
(5 squares) UL Type GI
Flintlastic STA 39 3/a"x 33%Roll. ASTM D 6222, Smooth surfaced APP Modified
Weight:90 lbs. Grade S,Type II Bitumen membrane with non-woven
{1 square) polyesCer mat-reinforcement for torch
application.
Flintlastic GTA, GTA-FR 193/8,,03'3";3";Roll ASTM D 6222, Granule surfaced APP Modified
weight; 105 lbs. Grade G,Type II Bitumen membrane with non-woven
(1 square) polyester mat reinforcetnent.for;torch
application.
Flintlastic GMS', 39 3/a"-X.34'2";Roll ASTM D 6164, Granule surfaced SBS Modified
GMS Premium weight: 100/105 lbs, Grade G,Type II Bitumen membrane with non-woven
(1 square) polyester that re inforceinent-for mop..
application.
Flintlastic FR, 39 3/8" x.34'2";Roll ASTM D 6164, Fire resistant;granule surfaced SBS
FR P Premium
weight: 105 lbs, Grade G,Type I Modified'Bitumen Membrane with
-?
(,:square) non-woven polyester mat
reinforcement for mop application.
Flintlastic FR Cap Sheet 39*3/8"x 34'2";Roll ASTM D 6163, Fire resistant,granule surfaced SBS
weight;90 lbs. Grade G,Type I Modified Bitumen membrane with
(1 square) fiberglass mat reliiforcement for mop
applications.
MIAMI•DADE COON'iY
NOA No.: 14-0224.03
••• F Expiration Date: D6/19/18
Approval Date: 04/10/14
Page 2 of 16
TRADE. NAMES OF PRODUCTS MANUFACTURED OR LABE'LED'BY APPLICANT:
TA'OLL I
Test Product
Product Dimensions Snecificatio�n, Description
Flintlastic FR Cap T 39,3/8"x 34'2";Roll ASTM D6.163 Granule surfaced SBS Modified
weight:.81lbs..- Bitumen membrane with fiberglass
(I square) mat reinforcement for torch
application,
Flintlastic FR Base'T 39m'3/84'k 33';Roll ASTM D6163 Modified Bitumen,coated fiberglass
Weight;81 lbs. base sheet for totch application.
.(1.0 squares)
Flintlastic FR Cap CoolStar 39 3/$" x 34'2";Roll ASTM D,6163 Fire resistant, granule surfaced SBS .
weight: 90 lbs. Modified Bitumen membrane with
(I:square) fiberglass mat reinforcement-for mop
applications. Coveted with reflective .
CoolStar Coating.
Flintlastic FR Cap T CoolStar 393/8 x 34'2";Roll ASTM D 6163 Fire resistant,granule surfaced SBS
Weight:90 lbs. -Modified Bitumen membrane with
(I square) fiberglass mat reinforcement for mop-
applications, Covered-with-reflective
CoolStar Coating.
Flintlastic GTA,GTA-FR 39 3/8" x33'3";Roll ASTM D 6222 Granule surfaced.APP Modified .
CoolStar weight: 105 lbs. Bitumen membrane with non-woven
'(1 square) polyester mat reinforcement for torch
application. Covered with reflective
Cool Star.Coating.
Flintlastic GMS/GMS 39.3/a".x 34`2";Roll ASTM A 6164 Granule.surfaced SBS Modified
Premium CoolStar weight: 100/105 lbs. Bituinen'membrane,with non-woven
-(1 square) polyester inat reinforcement-for mop
application, Covered with'reflective.
Coolstar.Coating.
Flintlastic FR-P/FR-P Premium 39'3/$" x 34'2'.';Rofl ASTM D 6164 Fire resistant,.granule surfaced SBS .
CoolStar weight: 1'05 lbs. Modified.Bitumen Membrane with
-(1 square) non-woven'polyester mat
teinforcement for mop application.
Covered with reflective'CobiStar.
Coating. Covered with reflective
CoolStar Coating:
Ultra Poly SMS 36"x 64'4" ASTM.D 6164, Smooth surfaced SBS Modified.
(2 squares) Grade S,Type I Bitumen Membrane with rion-woven .
polyester mat reinforcement for mop
applications..'.
MImNO No;: 14.V24.03
MI•DaDe eoUF g Expiration pater 06/19/18
Approval Date-,'04/16/14
Page:3 of 16
GlasBaseTM Base Sheet 36" x 98'9'; Roll ASTM D 4601 Asphalt coated, fiberglass base sheet.-
weight:69 lbs. UL Type G2
(3 squares.}
PolySMS Base Sheet 393/8,, x 644";Roll ASTM D 4601, Modified Bitumen coated polyester
weight: 90 lbs. Grade S;Type II base-sheet.
(2 squares) UL Type G2,
Yosemite(D Buffer Base Sheet 36" x 32'10";Roll ASTM D 3909 Mineral Surfaced fiberglass reinforced
weight: 96 lbs. ASTM D 4897 buffer sheet.
(i square) UL Type 30
Black DiamondTN'Base Sheet 36"" x 687';Roll ASTM D 1970 Self-adhering,fiberglass reinforced
Weight:. 78 tbs. modified bitumen-base,-sheet.
(2 squares)
APPROVED INSULATIONS: .
TABLE 2.
Product Name Product Description Manufacturer
(With Current NOM
FlintBoard ISO Polyisocyanurate foam insulation CertainTeed Corporation
ACFoa►n-I1 Polyisocyanurate foam insulation Atlas Roofing Corporation .
High Density Wood Fiberboard Wood fiber insulation board Generic
Perlite Insulation Perlite insulation board Generic
DensDeck,DensDeck Prime Water resistant gypsum board Georgia Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels LLC
ENRGY 3, ENRGY 3 25 PSI Polyisocyanurate foam insulation Johns Manville Corp.
Multi,Max FA-3 Polyisocyanurate.foam insulation RMax Operating,LLC
APPROVED FASTENERS:
TAI)LE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NON)
1. None N/A None N/A
NOA No.: 144224.03.
htlAMI.pac►eCOUNTv expiration Date;
. 06119 IS
Approval Date. 04/10/14
Page 4 of 16
EVIDENCE SUBMITTED:
Test Agency'Adentifier Name Report Date
Factory Mutual Research Corp. FMRC"4470 J.T.-3Y8ALAM 03/23./96
FMRC 4470 J.I,-OD3A3.AM 04/04/97
FMRC 4470 J.I.2DOAO.AM 12/23198
FMRC 4470 41-11)7MAM 11/09/98
Underwriters Laboratories,Inc,. UL 790 R11656 01/11/13
United States Testing Company ASTM D'51 47 97457-4 06/63188
ASTM D 5147 97-457-211 12/02187
Momentum Technologies,'Inc, ASTM 0'4601 AX31G8D 09/05/08
ASTM 06164 'AX31 08F 06/05/09
ASTM D6222 AX3108G 06/05!09
ASTM D3909/D 4897 AX3I68C 09/65108
Trinity'ERD "TAS 114(J) #3504.06.01-1 .06/05!01 I
TAS 117(B) 3503.10.06 10/10106
TAS 117(B) 06490.04.07-RI 06/27/07
TAS 1:14(H) Letter. 04/05/06
TAS 114 3533.01.06 01/06!06 . ' -
TAS 114 3521.07,04 07/29104
TAS 117 (B)/ASTM D 6862 C8500SCA 1.07 11/30!07
TAS 114 'C8370.08!08 08/19/08
ASTM Physical Properties C1008O.Q9.08-R4 03/25110
ASTM.D6164/D4798. C31410.04'.11-2 "01/10111
ASTM D4601 040050.09,11-1 09/28112
ASTM D1970 040050.09.12-2 09/28/12
ASTM D5147/D4798 031410.10.10-RI 11/01.112
ASTM D5147/D4798 C31410.01,11-1-R1 11/01!12
ASTM 04798 031410.01.11>2A-R1 02/21113
ASTM D4798 031410.12,13 12/05113
ASTM D6222 040050.12.13 12/05/13
PRI Construction Materials ASTM D6163 CTC-032-02-01. 01/22108
Technologies LLC ASTM 06163 CTC-066-02-01 08/09111
ASTM-D6164 CTG-068-02-01 08/09/11
ASTM D6222 CTC-070-02-01 08109/11
ASTM D'6164/D4798 CTC�093-02=01 08/09/11
ASTM D2178 CTC-122-02.01 03/13/12
ASTM")2178 CFTC-123-02-01 03/.13/12
ASTM D4601 CTC-127-02-0I 03/13!12
ASTM 1)6163 CTC-128-02-01 06/11112
ASTM D6163 CTC-129=Q2-01 06111/12
ASTM D6164 CTC-132-02-01 06111/12 "
ASTM D6164 CTC-162-02-01 05/09;13"
ASTM D6164 CTC-161-02-01 05/09/13
ASTM 06162 CTC-183-02-01 10/02113
ASTM D6164 CTC-190-02-01 12/02,13
MIAMI-DADE tong NOA No.: 14-0224.03
IIII� ' Expiration Dates 06/19/18
Approval Date: 04/10714.
Page 5 of 16"
Membrane Type: APP Modified
Deck Type II: Wood,Non-Insulated
Deck Description: Minimum 19.l32"thick plywood attached using approved nails spaced 4"o.c. at wood joists
spaced maximum 24""o. c
System Type E(3): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of All Weather/Empire Base Sheet, GlasBase or Flintglas Premium Ply Sheet(Type VI)
mechanically attached as detailed below.
Fastening: 413ase sheet shall be lapped 4"and fastened with I 1 ga.annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
Ply Sheet: (Optional) One ply of�;11Weather/Empire Base Sheet,Ultra Poly SMS, Glas Base,Flex-I Glas
Base,Flex-I Glas FR Base orr -bly SMS or one or more Flintglas Ply Sheet(Type IV)or
Flintglas Premium Ply Sheet(Type VI)adhered in a full mopping"of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq, or'one ply of Black Diamond Base Sheet
self-adhered or Flintlastic STA torch adhered.
Membrane: Flintlastic GTA,Flintlastic GTA CoolStar,Flintlastic GIA-E4 or GTA-FR CooIStar torch
adhered to base/ply sheet.
Surfacing: (Optional)Any coating,listed below,used as a surfacing,trust be listed within a current NOA.
Install one of the following:
1. 400-lb./sq. gravel or 300-1b:/sq, slag in a flood coat of approved mopping asphalt at an
application rate of 60 lb./sq.
2. Karnak(#97 AF)Fibrated Aluminum Roof Coating,FlintCoat A-150,APOC 4212
Fibrated Aluminum Roof Coating at an application rate of 1 �%x gal./sq
Maximum Design
Pressure: -60 psf. (See General Limitation#7)
NOA No.: 14-0224.03
IAMI•DADE COUNTY Ex iration Date: 06/19/18
Approval Date 04110/14
Page 14 of 16..
r �
WOOD DECK.SYSTEm LIMITATIONS:
L. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened'base or anchor sheet.
GLNERAL LIMITATIONS:
1. Fire classification is..noi part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2, Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers'shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq.,or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied-in approved asphalt, panel size
shall be 4'x 4'maxiinum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is .used the base sheet shall.-be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side lap and one down the center.of the sheet allowing a continuous area of ventilation. Encircling of the i
strips is not acceptable. AI6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems sliall be limited to'a maximum design pressure of-45 psf. {
S. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force(F')value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 405: If the fasfener value, as field-tested, are below !
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required,as determined by the Building Official, a revised fastener spacing,-
prepared,
pacing;prepared,signed and,sealed by a Florida registered Professional Engineer,Registered Architect, or.Registered
Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value
taken from Testing Application Standards TAS 105 and'ealculations in compliance with Roofing Application
Standard RAS 117.
J7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated 'in compliance with Roofing
Application Standard RAS 117. Calculations prepared,signed and sealed by.a Florlda registered Professional
Engineer, Registered Architect, 'or Registered Roof Consultant (When this limitation. is specifically,referred
within this_NOA,'Geocral Limitatidn'#9 will not be applicable.)
8. All attachment and sizing of perimeter nailers,metal,profile,andtor flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load.requirements. -
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones(i.e. field,
perimeters, and corners),Neither rational analysis,nor extrapolation shall be perinitted'-for enhanced fastening at
enhanced pressure zones(i.e. perimeters, extended-corners and corners). (When this'limitation is specifically
referred within this NOA,General Limitation#7 will not'be applicable.)
10. All products listed herein shall.havo a.iluality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative.Code.
END OF THIS ACCEPTANCE
NOA No., 1.44224.43
MIAM•oAna`c uNTY Expiratior+.Aate:`db719/18
Approval Data. 04/10/14 .
Psige.16 of 16