HomeMy WebLinkAboutProduct Approval i
From: 05/02/2016 07:55 #042 P.001/007
it
`. ` EXTERIOR RESEARCH&DESIGN,LLC.
Certificate of Authorization/19503
353 CHRISTIAN STREET,UNIT#13
`J TRINITYER® OXFORD,CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
Owens Corning i Evaluation Report 037940.02.12-R6
One Owens Coming Parkway FL30674-R1i
Toledo,OH 43659 Date of Issuance:02/06/2012
Revision 6: 10/15/2015
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has beenyeviewed by Robert Nieminen,P.E.for
use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the 5th Edition(2014)Florida Building Code sections noted herein.
DESCRIFRON: Owens Corning Asphalt Roof Shingles
i
LA8EUNG: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPUANCE: This Evaluation Report is valid until such time as the named products) changes, the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen,P.E.if the product changes or the
referenced Quality Assurance documentation changes. Trinity)ERD requires a complete review of this Evaluation Report
relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 7.
Prepared by: ttiutnn�
"A
t r
a -
�; Z.
4 ,:•E' � •mss.
Robert l.M.Nieminen,P.E. Thefacs4n3esealappearinswasauthorizedbyRobenNiemhren•
t•��`'/�\aV Vis.' P.E.on 10/15/201$.This does notserve as an electronically signed
Florida Registration No.59166,Florida DCA ANE1983 "���••'�t"`"v document.Signed,sealed hardcop'ies have been transmitted to the
CERTIFICATION OF INDEPENDENCE: Product Approval Administrator and to the named client
1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. TrinitylERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity ERD nor Robert Nieminen,P.E.are, in any,way)the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically for that purpose.
05/02/2016 0'7:55 0042 P.002/007
From:
TR11w- 11-TY;ERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles,as produced by Owens:!Corning,have demonstrated
compliance with the following sections of the Florida Building Code and Florida Buildi 1 9,g Code, Residential Volume
through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section prone Standard Year
1507.2,5,R905.2.4 Physical Properties ASTM D3462 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,8905.2.6.1 Wind Resistance ASTM D7158 2008
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File 82453,Vol.302/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120S16-R2453', 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL I.I.C.(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter j 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs I Various
UL LLC (QUA9625) Quality Control Service Confirmation,R2453 I Exp.08/20/2017
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic and Supreme are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire'are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 DevonshireT*are fiberglass reinforced,S-tab asphalt roof shingles.
4.1.4 Durationo, TruDefinition Duration*, Duration* Premium Cool, TruDefinitiotil. Durationo Designer Color
Collection,TruDefinition'Ciakridgeo,Oakridge*and WeatherGuard*HP are fiberglass reinforced,laminated
asphalt roof shingles. 1
4.2 Berkshire* Hip & Ridge Shingles, High Ridge, Hip & Ridge with Sealant, WeatherGuard' HP Hip & Ridge
Shingles,ProEdge Hip&Ridge Shingles and Durallldgem Hip&Ridge Shingles are fiberglass reinforced,hip
and ridge asphalt roof shingles.
4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
'I
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinitylERD nor Robert Nlermr�,_n, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
J
5,2 This Evaluation Report is not for use in the HVHZ. 1
5.3 Fire Classification is not part of this Evaluation Report, refer to current,Approved Roofing Materials
Directory for fire ratings of this product.
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R6
Cerqkv Le of Au tho dzaHD n M503 FLI0674-R11
Revision 6*10/15/2015
Page 2 of 7
i
From: 05/02/2016 07:56 0042 P.003/007
TRINITY ERD
5.4 Wind Classification:
5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H,indicating the shingles are acceptable for
us in all wind zones u V
p to V asd=150 mph(p „lt=194 mph). Refer to Section 6'for installation requirements
to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter,
Plus noted herein are
Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for us in all wind zones up to Vasd= 150 mph (V„h= 194 mph). Refer to Section 6
for installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less.
Calculations by a qualified design professional are required for conditions outside these limitations.
Contact the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C.Rule 611320-3.
6. INSTALLATION: !
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 611320-3,per FBC Sections 1507.2.3,1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the manufacturer's currentpublished instructions, using
minimum four(4)nails per shingle in accordance with FBC Sections 1507.2 or R905.2,with the following
exceptions:
D Berkshire'shingles require minimum five(5)nails per shingle.
y WeatherGuarde HP shingles require minimum six(6)nails per shingle.
Y Devonshire'°"shingles require minimum six(6)nails per shingle;
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nailslper strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. Contact the shingle manufacturer for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Fe4t un
derlaymeut ."yr Deck Feb undetesynlam Occk SeHddhered
y
Seff•adhered c. WeatherLOWI undedaymm t
WeatherLocke
underlayment
Drip_ .rDrip edge Drip. — — �Pedge
edge
edge + i ;
—Nails locatedNaas located
n3" rave 2'-3'from rare
Installfirst Self-sealing adhesive seHaeain edhosive
Starter Strip_ ,•• Instep first Starter strip Ms' •• g
shingle with positioned along rave sroonedalon rave
6"removed
Starter Strip shingle overhangs eaves and rakes 4i-jw Stan&Strip MS overhangs eaves and rakes IM-3/4"
I
Exterior Research and Design,LLC. ,Evaluation Report 037940.02.12-R6
Certf/leate o/Authorlration ASS03 FL10674-Ril
Revision 6:10/15/2015
Page 3 of 7
I
i
06/02/2016 07:57 #042 P.004/007
From:
1`R,INII " ERCP
6.2.6 Minimum Nailing—Classic®&Supreme:
I
Normal Moneard or Area porn Normef 'Manssrd or Anea para
Wind Areas High Wind deavanea V Wind Arora High Wind desvamw y
Area pare viontos normates =3 viorrtos Mertes Arca para vientos normates ;AT*" vientox foartaa
t• ��Ai in s x•l (BIS 2- s• r ..._ _ r r 'x=;fg'}' x- 'r
:sem
w Exposure[M. ,7 6 SOr Exposure
Exposiei6n Expoatai6n (I
6.2.7 Minimum Nailing—Berkshire':
°i.
5e81am strip seafal strip
Lafbad.ufiadtt L8frr8da dkdot
a t�^ a of a it a it a yr avr a+ir a+/r
t• t" t• t"
i
2" Asph.t 11.1 tingoeanent
Cemento de fiebode a!tatto
6.2.8 Minimum Nailing—Devonshire'"": 4
—_— +—t----•--^ter—^ Nails
I
Nails Ten'I'Spots of Asphalt Roof Cemeot
{
I
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R6
Cerdpeate of Authoriraffon#9503EL10674-Ril
Revision 6:10/15/2015
Page 4 of 7
nen
From: 05/02/2016 0 7:5 8 #042 P.005/007
TRINITY ERD
6.2.9 Minimum Nailing Duration®, TruDefinition® Duration, Durationo Premium Cool & TruDefinition*
Duration Designer Color Collection:
4 Wall Pattern 6Na6
Esquama de 4 davos Pattern
2M a Wet-0 eat 01C
SurejUPlasteningatea wkhb Esquema tol 0 Wma"
Area do dams SuMarl dq 8 daves opmWALMol
9wSuffliar rbp3l
11T suml
latteri L swftlp
arramNMI
WOW
kears
SWExposum Nab 6%'Exposure
Ah pulg,do exposid6n Mvos Aipufg.do exposkian
Wo'Exposure Naas W Exposure
Ri P010.&exposkidn C4 vI ol, 61,;pulg.do exl
6.2.10 Minimum Nailing—TruDefinition*Oakridge®,Oakridge®:
4 Nall Pal 6 Nall Pattern
aquema con 4 claws Euperna con 6 clavos
r
5 5W ExposureMy'ExposureNaas
Evo%fd6nd*6618jpdg Own EXPos1d6nde6616pzdg. Sliff'Exposure cWosxposure
Exposid5n do 654 pulp Exposidorr de 56/6 pufg
6.2.11 Minimum Nailing—WeatherGuard®HP:
atingle sib Vftw
Vhft AormW
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire'Hip and Ridge Shingles, High Ridge,Hip&,Ridge with Sealant,WeatherGuard'HP
Hip and Ridge Shingles and Prolidge Hip & Ridge Shingles shall comply with the manufacturer's current
published instructions, using four (4) nails per shingle. Installation of Durall'idgelm Hip &Ridge Shingles
shall comply with the manufacturer's current published instructions,using two(2)nails per shingle. Refer
to Owens Corning published information on wind resistance and installation limitations,including the use
of hand-sealing for wind warranties.
Exterior Research and Design,U.C. k
Evaluation Report 037940.02.12-116
CertifkatE qfAuthodzutibn#9503 FLI0674R11
Revision 6:10/25/201S
Page 5 of 7
05102!,2016 OI7:58 0042 P.006f007
From:
111TRINITY' ERCP
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905,2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshiree Hip&Ridge and High Ridge:
Fig,1 v...` , Fig,2 iI
�..— rneearav%und i"�— I TLpV�vN �I' SneViav
gnmion rte\:•.` \`•,' 111
rtaca jxals
TLplw"od
W?
` a a
f.-'
Ir
f
\
6.3.4 Minimum Nailing—Hip&Ridge with Sealant:
em Fkj.2-Hig nd Fwtwinq Pattem
�4 Naels�
sire Shingle
rxl Discard ,
Excless
Sealant ,l „
Strip T
'
Fastening S yle 5"Exposure
Distance I
12n
6.3.5 Minimum Nailing—WeatherGuard®HP Hip and Ridge:
-— Fig.C Hip&Ridge Shingle Fastening
Fig.A Topvlew 'I
Naito^--.—•_.._._.__--_—_T,44 ~�:.-� -.} '
v •� nails tails
A.
A.
4 E%peLLM
II b" Eryositre
v
I I
I
Exterior Research and Design,LLC. Evaluation Report 037840.02.12-R6
Certrpi vte of Authoriratlon#9503 FL10674-Rll
Revision 6:10/15/7015
Page 6 of 7
� I
i
I
:1":u+':..�T�w.tt,^h^?.,MYtntV,n^++.af'^7Y�ms'.c�.p.,•mm.....�....,•.�.«.x�.wn,Hm>.+�..y..�.w.wi..r-.w.mam,+na�r..�.........................................-w.�,-........._.-.._...._._..v...s-.-...w�-,-�.+-�..o-r-w.n.i-.m•w.—��...,...�r�a..rYi�. ...-.w...�.�...�,....�.�,�wm-:-.+.-._......»..._Y. �.+.....w.,..M..n.x�.n.,
From: 05/02/2016 07159 0042 P.007/007
IRD
TRINITY:
6.3.6 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard
Wind Direction Sealant Strip Fast Fattening
Patt:M
A-` 6'Exposure 7'_1
Sealant
Fasten 79r' 6. t
ir 61pasufa
Cover fixpoasd
Fasteners with
Roof COMM
..............
6.3.7 Minimum Nailing—Durallidgel Hip&Ridge Shingles:
Note: The drawings below pertain to minimum, as-tested attachment requirements. Refer to Owens
Corning published installation instructions for their minimum requirements.
=1,r%!�- n TOP
VW vu..
2
Ulu
e;� u
fig
1J J
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the.required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order.to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 CIA
requirements.
10. QuALrry AssuRANCE ENTITY:
UL LLC-QUA9625;(414)248-6409;karen.buchmann@ul.com
END OF EVALUATION REPORT-
Exterior Research and Design,LLC.
Evaluation Report 037940.02.22-R6
Cert&0care ofAutharization M03 FL10674-R11
Revision 6:10/15/2015
Page 7 of 7