HomeMy WebLinkAboutProduct Approval RECEIVED MAY 17 ?OiS
6 COPY
EXTERIOR RESEARCH& DESIGN, I.I.C.
UNIT#13
Q10TRINITYERD
La Cert�cate ofAuthorization#9503
353CHRISTIAOXFORD'CT 6478
,
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
Owens Corning Evaluation Report 037940.02.12-116
One Owens Coming Parkway FL10674-R11
Toledo,OH 43659 Date of Issuance:02/06/2012
Revision 6: 10/15/2015
SCOPE:
This Evaluation Report is issued under Rule 611320-3 and the applicable rules and regulations governing the use of
construction materials in the State ofTlorida.The documentation submitted has been reviewed by Robert Nieminen,P.E.for
use of the product under the Florida Building,Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the 5th Edition(2014)Florida Building Code sections noted herein.
DESCRIPnON: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is"valid until such time as the named products) changes, the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the
referenced Quality Assurance documentation changes. Trinity)ERD requires a complete review of this Evaluation Report
relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may be displayed in
advertising literature: If any portion of the Evaluation Report is displayedi then it shall be done in its entirety.
INSPECTION: Upon request,.a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 7.
Prepared by: nittrrrnr,
,►�
'�• u r
f`
1
%� Lh'• The facsimile seal appearing was authorized by Robert Nieminen,
Robert J.M.Nieminen,P.E. i14�J1�rJ�;LfG4Y, P.E.on 10/15/7015.This does not serve as an electronicagy signed
Florida Registration Na.59166,Florida DCA ANE1983 p •- document Signed,sealed hardcopies have been transmitted to the
Product Approval Administratorand tothe named client
CERTIFICATION OF INDEPENDENCE:
1. Tri nitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen,P.E..does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product:
5. This is a building code evaluation. Neither Trinity I ERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically forthat purpose.
QOTRINITYIERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated
compliance with the following sections of the Florida Building Code and Florida Building Code, Residential Volume
through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section PropertV Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM.D3462 2009
1507.2.7.1,11905:2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008
3. REFERENCES:
gnftz Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC.(CER9626). Physicals&Wind Resistance 20120516-112453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (O.UA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
m
4.1.1 Classic and Supreme are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire TM are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration% TruDefinition® Duration®, Duration® Premium Cool, TruDefinition® Duration' Designer Color
Collection,TruDefinition®Oakridge,Oakridge®and WeatherGuard HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Berkshire® Hip & Ridge Shingles, High Ridge, Hip & Ridge with Sealant, WeatherGuard HP Hip & Ridge
Shingles,ProEdge Hip&Ridge Shingles and DuraRidge'"A Hip&Ridge Shingles are fiberglass reinforced,hip
and ridge asphalt roof shingles.
4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials
Directory for fire ratings of this product.
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certiflcate of Authorization#9503 F L10674-R11
Revision 6:10/15/2015
Page 2 of 7
�TRINITYIERD
5.4 Wind Classification:
5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158, Class H,indicating the shingles are acceptable for
us in all wind zones up to V,,d=150 mph'(V„It=194 mph). Refer to Section 6 for installation requirements
to meet this wind rating.
5.4.2 All Owens.Corning hip .& ridge shingles, Starter Strip Shingle and Starter Strip Plus: noted herein are:
Classified in accordance with FBC Tables 1507.2.7.1 and R905:2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for us in all wind zones up to V.,d= 150 mph (Vert= 194 mph). Refer to Section 6
for installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category Bor C and a building height of 60 feet or less.
Calculations by a qualified design professional are required for conditions outside these limitations.
Contact the shingle manufacturer for data specific to each shingle.
5:4.4 Refer to Owens Coming published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida.Building
Code and F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 611320-3,per FBC Sections 1507.2.3,1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four(4) nails per shingle in accordance with FBC Sections_1507.2 or R905.2, with the following
exceptions:
Berkshire'shingles require minimum five(5)nails per shingle.
➢ WeatherGuard®HP shingles require minimum six(6)nails per shingle.
➢ Devonshire7e shingles require minimum six(6)nails per shingle.
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5.. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. Contact the shingle manufacturer for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Felt underlayment Deck Fellunderlaymeat Deck Sell-adhered
WeatherLo"
Self-adhered underWymem
WeatherLocke
underlayment
Dag Drip edge D Drip edge
6
Nails locatedNads located
" 2'-3'from eave
2"-3 from cave
Install first Self-sealing adhesive Self-sealing adhesive
syrteStarter StripP Instal first Starter Strip Plus
igle
"uvith positionedalongeave vrith6'removed Postianedalongeare
6"removed
Starter Strip shingle overhangs eaves and rakes'/i='/i' Starter Sbip Plus overhangs eaves and rakes 114'-3/4•
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R6
Cerdflcate of Authorization#9S03 F L10674-R11
Revision 6:10/15/2015
Page 3 of 7
no
TRINITY I ER®
6.2.6 Minimum Nailing—Classic®&Supreme:.
Normal Mansard or Area para 7Wind
l Mansard or Area pain
Wind Areas High Wind desvanes y Areas HighWind desvanes y
Area pare vientos normelea Areas vientos fuertes para vientos normales Areas vientox fuertes
IAY 2' t'l s"
/JA �. s. 2. f6 2. �.
»• �r ;2� 12t
5"Exposure 5 5/8"Exposure
Exposieidrt Exposiei6n'
6.2.7 Minimum Nailing—Berkshire':'
Sealant strip Sealantstrip
La tira de s0sdor to ilia de seBadar
9 v 9w 8VT. t "8 Yt' 8V 811f 8W,
t
i
t
2.. Asphalt rooting cement
Cemento de techo de astalto
6.2.8 Minimum Nailing—Devonshire ll:
w
Nails
S'•: N: SK• G:•
Nails Ten 1"S ots of Asphalt Roof Cement
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certificate of Authorization#9503 FL10674-R11
Revision 6:10/15/2015
Page 4 of 7
QOTRINITYIERD
6.2.9 Minimum Nailing — Duration®, TruDefinition® Duration, Duration® Premium Cool & TruDefinition®
Duration®Designer Color Collection:
rtd
4 Nail Pattem 6 Nail �"Weennbetwrms aSNba�
Esquema de 4 clavas Pattern area andtop d wl od,
diar6art6 o Mes
Suejjb�l�ilefastening area width doe G clavoS ap dasfiRda rde.rtna el
Area de clavasSureNafNd easdexa3�pb yarla
Rpe orturaaa
Sureftata - \ Burexaita
+° +° tasted tasien�g
arawah ars widh
_ 12' 12' _ Aroada T' \1
_ Aram
dams
Su Nab E— 12' ` ^ ^12" Smeri IP
EW Exposure6s/e"Exposure
b�f ping.de expdsfdon NausClaws 6sh puig.de exp'osicion
5%Exposure Nags 5W Exposure
6%pufg.de exposition Clavos ,Ph pufgde euposid6n
6.210 Minimum Nailing.—Tru Definition®Oakridge®,Oakridge®:
4 Nail Pattem 6 Nail Pattem
Esquema con 4 clavos Esquema con 6 clavos
9• 1'
r r
1'r
55N'Exposure Nails 5 518"Exposure Nails
Exposlcl6nde6618paig Clavas Fxposfc+onde66/8pulg. 56/8"ExposureClavas 55/8"Exposute
Expos1d6n de 6618pulg Exposid6n de 56/8pulg.
6.2.11 Minimum_Nailing—WeatherGuard® HP:
1=
ilb
� _ 1 Ylifibril
:i•:•••
.s,.;: �;r• Fia6tr7hwnh Nil Lir
6.3 Hip&Ridge Shingles:
6°3.1 Installation of Berkshire®Hip and Ridge Shingles, High Ridge, Hip&Ridge with Sealant;WeatherGuard®HP
Hip and Ridge Shingles and ProEdge Hip & Ridge Shingles shall comply with the manufacturer's current
published instructions, using four (4) nails per shingle. Installation of DuraRidgel Hip & Ridge Shingles
shall.comply with the manufacturer's current published instructions,using two(2).nails per shingle. Refer
to Owens Corning published information on.wind resistance and installation limitations,including the use
of hand-sealing for wind warranties.
Exterior Research and Design,LLC. Evaluation Report 037940.02°32-R6
Certificate of Authorization#9503 FL10674•RSI
Revision 6:10/15/2015
Page 5 of 7
QOTRINITYIERD
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire®Hip&Ridge and High Ridge:
Fig.1 4 Fig.2
`—
Median on na lMnd TopVlew SideView
A
Has—). j.
Nails �Nails
4
I I 1' r Top Lan 4nated z' t
A I I 4' Piece
I I �
.� A I I 1i. 7• 1'
4 I 1 I
I I
Ir
� yl
Fxposum �I
I
I
I
I
I
1
6.3.4 Minimum Nailing—Hip&Ridge with Sealant:
em Fig. 7-High Wind Fastening Paittem
(4 Nails)
rim Shingle IP k
and Discard 2„ 2„
Excess ,111 111
Sealant -F
Strip T 12"
' Fastening 551.x" S"Exposure
Distance
12
6.3.5 Minimum Nailing—WeatherGuar&HP Hip and Ridge:
Fig.G Hip&Ridge Shingle Fastening
Fig.A 4 v Top"w
Prevailing wind
F—Direction A
A
flails
\ 4 4
A I Nails flails
♦4 I I 7� 2..
I
S'
E7tpOsure
S' Exposure,
12"
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certificate of Authorization X19503 F L10674-R11
Revision 6:10/15/2015
Page 6 of 7
�TRINITY(ERD
6.3.6 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard -11
Wind DirectionFastening
Sealant Strip Pattern
6'Exposure I�.� •I•� I'1'
t2° Sealant
Fasten 7'�t �'�_�
6"Exposure
Cover Exposed 1 1
Fasteners with
Roof Cement
6.3.7 Minimum Nailing—DuraRidgem Hip&Ridge Shingles:
Note: The drawings below pertain to minimum, as-tested attachment requirements. Refer to Owens
Corning published installation,instructions for their minimum requirements.
Pravaiing Wind Dirvcdon Top Via
—Diraaiondonimntad.wrntII• Vl"ata plan 1'IH
DiracdOn dal Ante pradornimnty
4
I Clou
r
ttviks��
b 2 j° . orfens coming surerlefr a c1OYD
C�Ivm �I I' I
r nror I I
$ I`
i
¢ +
P Imo—I1' I
7. LABELING'
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2. Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS;
As required by the Building,Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625;(414)248-6409; karen.buchmann@ul.com
- END OF EVALUATION REPORT-
Exterior Research and Design,LLC: Evaluation Report 03'7940.02.12-R6
Certificate of authorization#9503 FL10674-R11
Revision 6:10/15/2015
Page 7 of 7