HomeMy WebLinkAboutProduct Approval R U EP,"10 i IKI, 23 M
LE P®A EXTERIOR RESEARCH& DESIGN, I.I.C.
�f Certificate of Authorization#9503
TR�I�I�TY ER® 353 CHRISTIAN STREET,UNIT#13
OXFORD,CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
Owens Corning Evaluation Report 037940.02.12-116
One Owens Corning Parkway FL10674-R11
Toledo,OH 43659 Date of Issuance:02/06/2012
Revision 6: 10/15/2015
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,P.E.for
use of the product under the Florida Building,Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the 5th Edition(2014)Florida Building Code sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the
referenced Quality Assurance documentation changes. Trinity IERD requires a complete review of this Evaluation Report
relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building.Official.
This Evaluation Report consists of pages 1 through 7.
Prepared by: ��ntn�rrprn
V.
r�
• ,L^�t�.•* '.!• The facs'nnile seal appearing was authorized by Robert Niem inen,
Robert J.M.Nieminen,P.E. aFs� ;''" ,"c _
Florida Registration No.59166,Florida DCA ANE1983 :y`•l,ein `" P.E.m nt Sig 15.This does not serve as an en transmitted
signed
document Signed,sealed harden"ies have been transmitted to the
Product Approval Administrator and to the named client.
CERTIFICATION OF INDEPENDENCE:
1. TrinityJERD.does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. TrinitylERD is not owned,operated orcontrolled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically for that purpose.
��TRINITYIERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Sh ingles
Compliance Statement: Owens Corning Asphalt Roof Shingles,as produced by Owens Corning, have demonstrated
compliance with the following sections of the Florida Building Code and Florida Building Code, Residential Volume
through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM-D3462 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008
3. REFERENCES:
gniitlt Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic and Supreme'are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire'are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire''are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration', TruDefinition' Duration,, Duration Premium Cool, TruDefinition Duration® Designer Color
Collection,TruDefinition'Oakridge,Oakridge and WeatherGuard'HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Berkshire' Hip & Ridge Shingles, High Ridge, Hip & Ridge with Sealant, WeatherGuard HP Hip & Ridge
Shingles,ProEdge Hip &Ridge Shingles and DuraRidge'll Hip & Ridge Shingles are fiberglass reinforced,hip
and ridge asphalt roof shingles.
4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing :Materials
Directory for fire ratings of this product.
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certificate of Authorization#9503 FL10674-R11
Revision 6:10/15/2015
Page 2 of 7
QOTRINITYIERD
5.4 Wind Classification:
5.4.1 All.Owens.Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158, Class H,indicating the shingles are acceptable for
us in all wind zones up to Vasd=.150 mph'(V„it=194 mph). Refer to.Section 6 for installation requirements
to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter.Strip Plus noted herein are
Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for us in all wind zones up to Vasil= 150 mph (Vnit= 194 mph). Refer to Section 6
for installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B'or C and a building height of 60 feet or less.
Calculations by a qualified design professional are required for conditions outside these limitations.
Contact the shingle manufacturer for data specific to each shingle.
SAA Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3,per FBC Sections 1507.2.3,1$07.2.4 orR905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four(4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the.following
exceptions:
➢ Berkshire®shingles require minimum five(5)nails per shingle..
➢ WeatherGuard®HP shingles require minimum six(6)nails per shingle.
➢ Devonshire'm shingles require minimum six(6)nails per shingle.
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. Contact the shingle manufacturer for-details.
6.2.5 Minimum.Nailing—Starter Strip Shingle and Starter Strip Plus:
Feltunderlayment Deck Felt underlaymeat Deck Self-adhered
WeatherLockV
Sell-adhered undedayment
Weatherlocko
Underlayment
Drip_ Drip edge Drip---. Drip edge
edge- edge
Nails locatedNags located
2'-'from eave
2-3"from eave
Install list Self-sealing adhesive Self sealing adhesive
Starter Strip positioned along eave instal
ti"�6'removed
rst Starter Strip Pin Positioned along eave
shinglewep \ �
6"removed r r Starter tri Plus overhangs eaves and rakes 1141-3/4'
Starter Strip shingle overhangs eaves and rakes/i_/�" P 9s
Exterior Research and Design,LLC: Evaluation Report 037940.02.12-R6
Certificate of Authorization#9503 FL10674•Rll
Revision 6.10/15/2015
Page 3of7
f.
( 0
TRINITY I ERD
6.2.6 Minimum Nailing—Classic®&Supreme;
Normal Mansard or. Area para Normal Mansard or Area pare
Wind Areas High Wind desvanes y Wind Areas High Wind desvanes y
Area para womos normates Areas vientos fuertes Area para vientos normales Areas vientos fuerte5
t"11• .IA! tt,t` `t` 2` (A) 2• t"
727 121P
6"Exlposure 5 6/8"Exposure
Exposicidn -Exposici6n'
6.2.7 Minimum Nailing—Berkshire®:
Sealam strip Sealam strip
La tira de seflador !a Ura de sd iadar
T �5�---'►a a--� • e—'� •f---►• of--/a 4 —Te
9 Yt" 9 Yt 8 Yz" 1 "B.Yt' f3Yt' 8 Y 8Yf
Z` Asphalt,roefingcement
Cemento de techo de Wafto
6.2.8 Minimum Nailing—Devonshire':
T—
Nails
r r a' a a. r r r r c r r
S'.i FJA' YY 6`w
Nails Ten 1"Spots of Asphalt Roof Cement
.Exterior Research and Design,LLC. Evaluation Report 037940.02612-R6
Certificate of AutlfoNzatioa 119503 FL10674-R31
Revision 6:10/15/20.15
Page 4 of 7'
TRINJTY I ER®
6.2.9 Minimum Nailing — Duration®, TruDefinition® Duration, Duration® Premium Cool & TruDefinition®
Duration Designer Color Collection:
4 Nail Pattern 6 Nall R'hrcard and MUD Slopp4
erten between Sure0aa1°�
Esguema de 4 clavos Pattern area andtop d cut out.
uenta SuueNagefastening area width de Maws
aeras aenae el
Area de dauosSUueNailD d2aSueNaip yfaparfe
-y sr�eda r.4lraale
r r SureiYdDo \ Surenail�
lasteNnngg t�steninAA
area reidtb area wiatb
_ 12' 12 _ Arcade
Suer aBO 12' _ ` ` ^12-~ weria[P
Sia"Exposure 5V 63a"6cposure .
6'A ping.de exposid6pclavos 6s/a ping.de exposiei6a
5%"Fxposure Nags 5W'Exposure
51,5pulg.deexposicidn Davos 51Apulg.deexposid6n
6.2.10 Minimum Nailing—Tru Definition'Oakridge®,Oakridge®:
4 Nail Pattern 6 Nail Pattern
Esquema con 4 clavos Esquema con 6 clavos
1' 1'
r r
IF—
IT —sl I� ,r I� 12• -�►I IF ,z -�I
5618 Exposure Nails 5518"Exposure Nags
&posiddude65/8pulg. clavos Exposiddeda65/8ping. 55/8"Exposure Mayos 5518"Exposure
Exposiddn de 6610pidg. Exposi i6n de 56/Spu19.
6.2.11 Minimum Nailing—WeatherGuard° HP:
R-- I Ille Side View
s;:;.•,' :s• FidtaoRih.w�t Nrl lJin
cul mM!af5tr�fl�din
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire®Hip and Ridge Shingles, High Ridge,Hip&Ridge with Sealant,.WeatherGuard®HP
Hip and Ridge Shingles and ProEdge Hip & Ridge Shingles shall comply with the manufacturer's current
published instructions, using four (4) nails per shingle. Installation of DuraRidgeTM Hip & Ridge Shingles
shall.comply,with,the manufacturer's current published instructions,using two(2).nails per shingle. Refer
to Owens Corning published information on wind resistance and installation limitations,,including the use
of hand-sealing for wind warranties.
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certificate of Authorization#9503 F L10674-R11
Revision 6:10/15/2015
Page 5 of 7
�TRINrryIERD
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire®Hip&'Ridge and High Ridge:
Fig.1 4 Fig.2
<— Preval inp Wnd
Direction ZN� A Toptllea SiUeVieor
NaBs���4 A Nails Nails
Top Lece eJ
2' t
A Pi
¢e
A i �. ' •
4 I I
I I I
I I �
�EZPosnre—n EI
I
VI
I
I
I
I
1
1
6.3.4 Minimum Nailing—Hip&Ridge with Sealant:
tillem Fig. 2-High Wind Fastening Rattem
(4 Nails.
rim Shingj
nd Disr.,a2,�Excess —— :
SeallantStrip 124P
FasteningS"Exposure
DEistanae
12
6.3.5 Minimum.Nailing—WeatherGuard® HP Hip and Ridge:
Fig.C Hip&Ridge Shingle Fastening
Fig.A qv
vmla TopVkw
vreuuing
<—DlreCibn A
A
Na1Ls
A i i Malls Nails
)a 7"
4 I I z• 2"I I I I 1• 1.
I I r,,--r
AA ' i
5"
Exposu�
S. Ezposule
ir
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R6
Certifimte of Authorization#9503 FL10674-R11
Revision 6:10/15/2015
Page 6 of 7
QTRINrryIERD
6.3.6 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard -71„�
Wind Direction Fastening
Sealant Strip Pattern 27
6'Exposure ��«I I'
t2' 1 Sealant
r7lb”
,Faste17J=am6"ExposuredI+ 11 1Fastenh
Roof Cement I_ t2,--►�
i
6.3.7 Minimum Nailing—DuraRidgeTMl Hip&Ridge Shingles:
Note: The drawings below pertain to minimum, as-tested attachment requirements. Refer to Owens
Corning published installation instructions for their minimum requirements.
Frovailing Wind Oiretdcn Top View
�Mroctiondornimntadrvsnt I1- VWe We
Oi 1 IH
e=dolvimbo�pr•dornirunt.
or
NO
r
clow
y • Orcens Conning Surcrlail' • G°°
Nai6t��
f�ar•oe� i i I
I
1 f + Flo
fUi
- I
12-
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC--QUA9625;(414)248-6409;karen.buchmann@ul.com
- END OF EVALUATION REPORT-
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R6
Certif ate of Authorizotion#9503 FU0674-R11
Revision 6:10/15/2015
Page 7 of 7